Paging setup with HT503 and Bogen system

We have to setup a Bogen Paging system using a HT503 ATA device in local GW FXS port for CUCM.
Please provide an understandding on how this is gonna setup.
It will have multizone paging i.e. if you press different number it will page out different zone.
Generally we create a Route pattern which will go to the gateway and activate the FXS port.

OK, first of all, you will not be connecting the FXS port of the 2921 to the HT503. The HT503 LAN port need to be on your LAN and you need to configure it as a SIP gateway. The 2921 is not needed to access the Bogen.
A multi-zone paging adaptor needs to use a trunk port. Correction: most multi-zone paging adaptors need a trunk port; It is possible (which means someone has done it) to configure a paging adaptor on an FXS port that connects and then waits for a DTMF tone to select the zone.
Based on the code you mentioned, I assume you are talking about a Bogen UTI312 unit, which does use an FXO port. It needs an FXO port (i.e. trunk port) because it is expecting call setup signalling over the line. That signalling would be the selected zone. So the setup here would be the CUCM has a route pattern that sends the Bogen code (i.e. *01) as the called number and routes the call to the HT503 gateway, which is setup as a SIP gateway in CUCM. The SIP gateway on the HT503 is configured to route any call that starts with an '*' to the FXO port. And finally the Bogen in connected to the FXO port of the HT503.
HTH,
Chris

Similar Messages

I have interface M Audio firewire 400 new Mac Pro has firewire 800 Do you think an adaptor will provide the same quality? Will the M audio 400 work with lion and new system? Thanks so much

I have interface M Audio 400 with 400 firewire new Mac Pro has firewire 800 Do you think an adaptor will provide the same quality? Will the M audio 400 work with lion and new system or do I need new software? Thanks so much

If you have a little Firewire adaptor, everything should work fine. It does on my system.

Can I use our PC with existing SCXI setup (conencted to a PC by PCI-MIO-16E4) and use one labview application to communicate with FP and SCXI systems at the same time?

We have an existing PC with SCXI setup. can i plug in a PCI-485/2 card connected to a FP-1001 network, and get both systems to be utilized in a single labview VI?

Yes, you can utilize both sets of resources (SCXI and FieldPoint) at the same time from the same VI.
If you were using the SCXI RS-485 interface, the SCXI and FieldPoint system would have to be on separate serial ports. Beyond that, there should be no real restrictions on accessing both of them.
Regards,
Aaron

Problem with Spotlight and some system problem, Please HELP!

I'm using iMac G5 with iSight (10.4.8)
Recently, I've noticed that my spotlight didn't search anything, when I type something it just do nothing.
I try to re indexing the spotlight by move the HD to the privacy zone in the spotlight preference but nothing appear on the list. I can't add anything to the privacy zone both by draging the folder or click + button.
Then I search for the application that can clear the cache and re indexing the spotlight, I found Onyx and Maintenance.
Both of them can't be open, it say that I have to use an admin account.
Even I was logged in as a Admin, I have only one account in the system and set as an admin already.
So, I search on the internet and someone suggest another way to re index in terminal by using this command: sudo mdutil -E /
First I open the terminal and type the command, it said "-bash: sudo: command not found "
So, I try to use terminal by boot on the DVD that bundle with iMac, and same result.
I tried boot in single user by press command and S when boot and type sudo command, same reult.
Another information, I noticed on my macbook when I open the terminal, it will show this info:
Last login: show the time
Welcom to Darwin!
My computer name
But on my iMac, it didn't show anything except only the computer name line.
What should I do? Thanks

Highly recommend that you read, reread and understand the consequences and then follow the directions as presented on X Lab
http://www.thexlab.com/faqs/stopspotlightindex.html
That is before you follow some of the directions you find on some of these discussions. Even mine.

Integration with ERP and other systems

We have integrated iP Oracle with OEX and we are now trying to
integrate with BBP/SAP, Maconomy Procurement systems. Has anyone
tried to integrate OEX with other systems?

We are now running a project to integrate OEX with SAP R/3 4.6c (MM Module). Oracle recommendation includes semiautomatic process associated to the RFQ in SAP and P.O. placement in SAP.
This semiautomatic process is consequence of poor XML integration with some transaction on OEX in which the buyer needs to operate in both systems: SAP and OEX. Nevertheless we are trying to request the incorporation of this changes in OEX's new version.
Its a matter of time that ORACLE will understand that a full integration is needed to satisfy users; SAP has done it and most of ERP transactions can be taken to XML format through their product Business Connector (Original a Webmethods product bought by SAP).
Juan Carlos Blesa

Airport express setup with iPad and no computer -- possible?

In September I will be staying a week in Germany in an apartment that lacks wireless but does have a broadband LAN connection. I would prefer not to take my MacBook Pro and, instead, rely on my iPad 2. But there's the rub: no way to connect via ethernet. I do have an Airport Express I could take with me. Is there a way to use it, creating my own wireless network, without having a laptop with me and using Airport Utility to set it up? Or am I stuck with lugging my MacBook Pro?

Is there a way to use it, creating my own wireless network
What I do with my Airport Express is to configure it to create a wireless network using DHCP at home before I leave, and then wherever I am, I just plug it in to the network via ethernet cable and turn it on. The Airport Express will grab an IP address from the ethernet network and create its own network that you can connect to.
So far, that has worked for me everywhere I have been.
From reports it appears iOS 5 will have the ability to configure an Airport Express, but we don't know the release date of that.

Windows 7 64bit Raid 1 Data Storage setup with UEFI and 6TB drives

i just bought a GigaByte MB with UEFI bios, 1 SSD 128GB drive for the OS (boot up), and 2 6TB drives for use in a raid 1 setup for the data storage.
I have been able to install win 7 64bit using the UEFI dvd drive. I have been able to define the 6TB mirror via the bios (under the Intel Rapid Storage Technology option) . But when ever i go into windows, and check under Disk Management, i don't
see the raid 1, i see two drives listed for the data, each at 1492 GB. I should be seeing 1 drive at 5.4TB.
note: I have tried re-installing win7 64bit many times to see if i have missed something. When i run setup off uefi dvd drive, i see that drive 1 (of what should be part of the mirror) and drive 2 are listed there at the reported 1492 GB size each.
So it seems that win7 doesn't see that mirror that i created via the bios. So is this a bios setting problem somewhere? i presume on this screen i should see the correct mirror size already.
Also, do i need to install win7 via the uefi dvd if i don't want to boot off those large drives (i just want to boot off the ssd. But when i did try that using a legacy mode, i couldn't later try to create a single large drive for the mirror using
GPT formatting. it just wasn't an option. although the mirror was recognized as 1 drive, but broken into 2TB and 3TB.)
what could i possibly be doing wrong??
Thanks for any help

Thank You Roger. I did call Gigabyte. This is how i solved it with the gigabyte support team.
1. Don't try installing Win7 64bit sp1 and setup RAID at the same time. (even go ahead and unplug those raid drives if you have it plugged in). The OS should be installed first on the boot drive, but make sure the BIOS is already set
to RAID (not AHCI. If you already installed OS under AHCI, you need to reinstall OS. i find this crazy because what if you decide to install raid down the road.. to an existing machine.. you can't do that because of this). Make sure
to install OS with the UEFI dvd drive option (i had done this).
2. Once the OS is installed, install all drivers that come for the Motherboard... That should include intel Raid drivers. (note gigabyte support didn't tell me to do this, but i didn't want to take a chance to have to reinstall OS again or have more problems,
but it makes sense.)
3. Now i have the GA-H97-Gaming 3 mother board, it had Bios F3. I upgraded it to F5 as per support tech.
4. turn off machine, and replug in the two 6TB drives.
5. after reboot, i find out that i no longer see Intel RAPID Storage Technology. (this should have displayed when i set the SATA Mode Selection to RAID before i started all this business... it did under bios F3, but not under F5.. bug?? i think so,
so i plan on letting gigabyte know about this). This is a problem. In Intel RAPID Storage Technology is where you define the RAID in the first place. OK, well after several reboots.. i tried to use CTRL-I to get to intel's interface
rather than that of the gigabyte bios. Voila... i define the Mirror...
6. I am able to boot into OS. I got to Drive Management. I now see 1 6TB drive. I initialize it of course using GPT. Format it. All all looks good now.
Hope this helps someone.. took me enough tries to get it right. I really am bothered about requiring the OS installed in the correct SATA mode just to get RAID working. As i mentioned, you can't change your mind afterwards without reinstalling
OS. Also i couldn't even get the OS setup to start when i had those raid drives plugged in.. so make sure to unplug them.
Best Regards.

Extended network setup with printer and airport disk

The network I want looks like this: The modem plugs into Airport Express using ethernet. Audio plugs in here to go to the stereo for music. Then the signal is sent wirelessly to an Airport Extreme in the other room, which has a printer and a hard drive connected to it.
I can't get the Extreme to stop flashing yellow. I tried extending the network created by the Express. I tried a WDS network with Express as main and Extreme as remote. Same network name, different network names, factory resets...I seem to be at a loss. I had an older "Snow" type Airport and I had the printer working on it (though it didn't support hard drives). I can't seem to duplicate the steps I took when I set up that network.
Thank you for any help you may be able to offer.

Tim,
It would help to know which AirPort Extreme, 802.11b/g or n, and Fast Ethernet versus Gigabit, and Express (b/g or n) devices you have.
Also, if you have any of the newer 802.11n AirPort devices, make sure that you update the firmware and AirPort Utility software.
If you're trying to setup a WDS, that's for 802.11g and if you're trying to "extend" a network, that for 802.11n.
Hope this helps.

X.75 ISDN test setup with 2811 and PVDM2-12DM modem

Hi all,
We have a customer that requires ISDN-X.75 connection as a back-up for IP. This is used by emergency services that require redundancy. We have to build a test set-up. We have two routers with the modem cards and with HWIC-1CE1T1-PRI= cards. We need to build a test set-up to simulate an incoming call. With ISDN-V110 we could use one of the routers to place an outgoing call to the other router. This set-up is not possible with X.75, since the card can not dail out. What would be the best/cheapest/simplest approach to build this test set-up?
My involvement in this project is to build a Perl script that collects data via IOS using expect. If someone has the procedure to collect the calling and called line information for a connection with an example I would be very grateful. Our routers run Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3).
For V110/V.34 and X.25 the tty/vty is collected by issueing a show tcp to relate an IP connection that is created to the tty/vty. The tty/vty port is then correlated to the calling and called line id. This is done with show x25 vc for X.25 or show modem csm for V.110/V.34. We need something similar for X.75 to distill the calling and called line IDs for a given TCP connection.
Thanks in advance!

It colud be Hardware(Digital Modem Module ) problem.
Try this link:
http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a00806b941f.html#wp1068376

Database setup with MySQL and PHP question

Hello all,
I recently had a problem getting a report to work for a site I was updating. This site is written in PHP with a MySQL database. The application is to track customer calls to auto repair stores. The database has a lot of foreign keys because they wanted to update information in only one spot and have multiple records be updated all at once. So, I've got all the information from individual calls saved in the call_log table, and have foreign keys to reference information in other tables (for example this table lists what store received the call referencing the store table). If a store changes locations, they want to have reports automatically update with the new address, connection to conversation number, etc.
In one of the responses to my question on how to get this report to work, I was told that this could be done without using foreign keys (by Normalizing the database using mapping tables). I am still a newbie to MySQL, and after looking though a lot of manuals, tutorials, and forum posts, I am more confused now than ever.
I got the report to work using the foreign keys, but I would like to learn what I should have done with the database (and how to get the information displayed).
So for example one report would be displaying the following:
           Store                                                      Reason for the Customer Call
                                           breaks             oil change            shocks              tune up         total calls
5636 - Bloomington                  2                       4                        0                       2                   8
8875 - Duluth                           1                       6                       4                        8                  19
with links on the store name to pull up the information on that specific store. How would I change the database (listed below) to do this without foreign keys? Any help would be greatly appreciated.
call_log             (table that contains the following:)
call_id
conv_number
date
camp_type         (foreign key to the campaign table so it displays the campaign_id)
reason               (foreign key to the call_reason table so it displays the reason_id)
location              (foreign key to the store table so it displays the store_id)
associate
call_summary
trainig_issue      (foreign key to the training_points table so it displays the training_key_id)
visit_closed
example            (foreign key to the example_type table so it displays the example_id)
campaign          (table that contains the following:)
campaign_id
campaign_name
campaign_promotion
campaign_coupon
campaign_startdate
campaign_enddate
call_reason       (table that contains the following:)
reason_id
reason
store               (table that contains the following:)
store_id
store_number
store_address
store_city
store_state
store_postalcode
store_name
store_phone
store_email
store_mgr
training_points (table that contains the following:)
training_key_id
key_issue
policy
example_type (table that contains the following:)
example_id
example_name
example_image
Thank you very much.

Frankly, that is way to much of a question to be answered in detail on a forum... There's a lot involved and a lot of general database understanding required. I would highly recommend:
Database Design for Mere Mortals:                       A Hands-On Guide to Relational Database Design, Second                       Edition -- by Michael                     J. Hernandez
This is an invaluable book to get you going in the right direction and on a firm foundation.
Lawrence   *Adobe Community Expert*
www.Cartweaver.com
Complete Shopping Cart Application for
Dreamweaver, available in ASP, PHP and CF
www.twitter.com/LawrenceCramer

Replace bzip2 and gzip with pbzip2 and pigz system wide?

I just now got word of these multithreaded ports and would like to know if theres anyway to replace their single threaded brethren? pigz is already in AUR and it wouldn't take much to put pbzip2 into it either.
Maybe some global variable should be set?
Edit: Strike the part about pbzip2. It's already in community
Last edited by uncholowapo (2010-10-10 23:48:04)

karol wrote:One thing you may want to check: if you compress a file w/ pbzip2 and send it over to me, will I be able to uncompress it with bzip2?
I just did some testing by downloading the Linux kernel source, and then using bzip2 and pbzip2 to decompress and recompress it several times. In another terminal window I monitored the speed of each CPU core by running:
watch 'cat /proc/cpuinfo | grep MHz'
What I found out was that yes, the files created by either tool will be able to be decompressed with the other. However, if you use pbzip2 to decompress a file compressed with the regular bzip2, it will only use one core. Only when decompressing a file that was compressed with pbzip2 did pbzip2 use both CPU cores.

Help with partitions and file systems [SOLVED]

Hi, i have been using Ubuntu for a while, and now i want to move to Arch. I've probed it in a PC and i like so i want to make que change.
But, before installing Arch, I have 2 doubts. I red the beginners guide and also the instalation guide. There it says that if better to have diferents partitions for /, /boot/, /home, /usr, /var, y /tmp
Usually, i alwayes used something like this:
* /boot (32megas)
* /swap (512 megas)
* /root (6 a 8 gigas)
* /home (80 gigas aprox)
It's really better to also have partitions for /var, /usr y /tmp? o some of them? and, in that case, wich size should i give them? because i don't want to make them too small, but i don't want to waste disk space neither.
Adn that takes me to my second question, wich filesystem is better for each partitionn? in many places, i read taht JFS its good for /var or that XFS if better for /home and big files
I thinked to use something like this:
* /boot (ext2)
* / (JFS)
* swap
* /home (XFS)
Is a good design? or should i use other filesystem like reiserfs, etc... and for /var, /usr and /tmp partition, wich one should i use?
Thank you
Ps: This Pc is gonna be a desktop pc
Ps2: sorry for my bad english. it is not my real lenguage
Reason of edit: added the swap partition. I forgot it
Last edited by Thalskarth (2008-12-21 20:11:00)

thanks everybody for the help,
kaola_linux wrote:@Thalskarth - it's better to have /var especially if you're using ext3 or other filesystems which was designed for larger files as your partition for /home and /. Having a seperate partition for /var would be nice (backup purposes and reinstalling without downloading the entire package whole over again). 5gb would be sufficient for your /var, anyway you can always resize it to your needs.
so, a 5gb partition in reiserfs would be OK for a /var
Inxsible wrote:
Lot of people also use XFS which is known to have better performance with huge files. I think EXT3 offers a good balance...because I am never sure whether my home partition will have all huge files or not..same with my external drive...so i just use EXT3
If you have a specific partition for movies or some video/audio editing that you do..you may wanna consider XFS too. I don't do all that...so I have never used XFS. I wouldn't know the exact performance difference between ext3 and XFS.
Yes, in many places i red that XFS is better for big files. But i couldn't fine wich is the meaning of "big file". Does it mean a 200 mg file? or a 4.4gb one??
the same applies to reiserFs, what is a small file? a 1mg one or a 4kb one?
I have alwayes used ext3, i thinked in XFS and JFS just to give them a try.
amranu wrote:I have no idea about better filesystems, all my partitions are ext3 (soon to be ext4)
Inxsible wrote:One thing that makes me wanna keep EXT3 is that EXT4 is coming out (soon?) and you can upgrade from 3 to 4 without having to reformat and having to make backups of your current data.
really is cominf soon? i didn't think in ext4 beacuse many places said that was in development for many years... meybe they were a bit out-of-date
Edit: i search in the wiki and it says that since 11 october 2008, ext4 is "stable" and is been included since kernel 2.6.28 as stable realase, is to early to prove it? or it better to wait a while??
thanks.
and, does anyone try the JFS one?
Last edited by Thalskarth (2008-12-03 00:14:56)

Pc icloud setup with IE9 and windows live mail

can the icloud be set up on a pc with windows 7 using IE9 and windows live mail?

No, he means this:
http://download.live.com/wlmail
Please adivse when PC Suite will support Windows Live Mail (it includes a calendar too)
Message Edited by spiny on 05-Mar-2009 11:19 PM

New setup with Yosemite and CC 2014 Speedgrade

Sg will not open for me at all. I was able to use it before when running Mavericks and before the latest update to CC 2014. I was thinking it had something to do with my Yosemite installation, but after doing a fresh install of everything it still will not open. Am I the only one having this problem?

Having both AMD + nVidia in my Mac Pro has work wonders. I have two DVi monitors connected to the nVidia card and single monitor connected to the display port on the AMD card. When I received my Mac Pro I had the option to add two AMD cards which requires more power than the Quadro card and the AMD put together. I'm using a splitter for power.
I have been able to get working. (for how long is the question) I only ran the nVidia card and BAM, Sg worked. I then only ran the AMD card and BAM, Sg worked. I then added both cards back and BAM everything is now working. I'm at a lost..... The weird thing is I can't view any .MXF file when going directly to Sg, but I can if I us dynamic link from Premiere. I can though import .mp4's in Sg and can view them with no problems.

BILLING SETUP WITH NOMADIX AND CISCO WLC

Hai I need to implement cisco wireless controller along with nomadix box for bandwidth control and billing in a hotel . anybody implemented same ?.
how the topology in this case ?.nessary config on wlc

Refer the post: https://supportforums.cisco.com/discussion/11431756/wlc-and-nomadix
https://supportforums.cisco.com/discussion/11601111/guest-ssid-redirect-nomadix-box

Paging setup with HT503 and Bogen system

Similar Messages

Maybe you are looking for