PC Used to work with XP and airport Extreme Basestation but not with Vista

Please help, my PC Used to work with XP and airport Extreme Basestation but not now with Vista. I have a MacBook Pro connected and also a Mac Pro connected to the network on it and they still work, i have put the latest software on the PC and the firmware is up to date. The only thing i can see on the network on the PC is the basestation Hard Disk (shared also to the Macs) but i cannot connect with the password, i have tried everything in my knowledge, including formatting the machine and reinsatlling OS and changing security setting to no avail. Any ideas anyone?

With regard to your printer problem - take a look at this discussion:
http://discussions.apple.com/thread.jspa?messageID=6312413&tstart=0

Similar Messages

  • Are there any compatibility issues with Sonos and Airport extreme??

    are there any compatibility issues with Sonos and Airport extreme??

    Sonos uses its own priopietory wireless protocol SonosNet to distribute audio data among all its products, thus it should not affect other network devices which use standard WiFi 802.11a/b/g/n protocol at all though they may share the same radio channel for wirless signaling.
    On my dual-band (5 GHz / 2.4 GHz) Airport Extreme staion, I select the option "802.11n Only (5GHz) - 802.11n (2.4GHz)" and turn on "Use wide channels" in Wireless configuration in order to use only 802.11n protocol and more radio channels to achieve maximum wireless bandwidth of 400 Mbps. This bandwidth is necessary for quick Time Machine backup to NAS connected to the Airport Extreme station through Ethernet cable. So my iMac and MacBook Pro always connected to the Airport Extreme through 5 GHz radio channel with 802.11n protocol whereas my iPhone 4S always connected through 2.4 GHz radio channel with the same protocol.
    In my living room Sonos ZP-90 (same as new CONNECT model) zone player is connected to Airport Extreme directly through Ethernet cable (recommended by Sonos) and Sonos S5 (same as new PLAY:5 model) zone player in bedroom is connected wirelessly through SonosNet protocol to the ZP-90 zone player in living room.
    These devices are in operation simutaneouly most of the time. Music is playing through the Sonos ZP90/S5 zone players througout the day, I am streaming viedo through Internet (fibre broadband 25 Mbps) on my MacBook Pro in bedroom or iMac in living room or reading news on my iPhone. So far so good and have no encounter any interference problem for about three years. Further more bandwidth for 802.11n protocol does not seem to be affected at all.
    In fact with a low power Fujitsu USB drive (2.5" / 500 GB, designed for notebook) plug into USB port of Airport Extreme, it can be used as NAS drive for Sonos music distribution system without any problem. Just transfer all files from Music folder in my home directory on iMac into this NAS drive and set it up as music source in "Manage > Music Library Settings" in Sonos Controller for Mac application will do. Though the same drive can be served as Time Machine's backup disk as well, an independent full-fledged NAS drive for Sonos and Time Machine backup is better long-term solution for reliability and performance. With the NAS configured as sole music source, you do not need to keep any computer powered on all the time in order to play music through the Sonos system.

  • HT3669 Hi I have a Konica Minolta PagePro 1300W printer. This works with my Windows-based Toshiba laptop but not with my i-Mac. Can someone please advise me how I get the printer to work with my i-Mac? I have installed it but documents don't print. Thanks

    Hi I have a Konica Minolta PagePro 1300W printer. This works with my Windows-based Toshiba laptop but not with my i-Mac. I have the latest (Mountain Lion 10.8.2) OS-X software.
    I have installed the printer using 'System Preferences' on my i-Mac and it appears on the list of available printers but documents that I create just don't print.
    Can someone please advise me how I get the Konica Minolta PagePro 1300W printer to work with my i-Mac?
    Thanks, John Lee

    Looking at the Konica web site for the PagePro 1300W, I saw the following note.
    Please note: This printer is designed to be used in computer operating systems running MS Windows only. Operating systems such as UNIX, Macintosh, or Linux are not supported nor do we have workaround drivers available. Older MS Windows versions, such as Windows 3.1/95/98[pre-SE] and NT 3.51/4.0, are not supported.
    So KM are not going to help you. But the LinuxFoundation does provide a workaround that should allow you to print. Have a look at this web page. You will need to install all three packages as per the instructions from that page.

  • DNS Server Issues with Comcast and Airport Extreme wifi routers

    I am having significant challenges with 3 Airport Extreme (latest gen) wifi routers and my Comcast Xfinitity service.  It once worked just fine, but now I continually get the blinking amber lights stating "No DNS servers" for each of the Airport Extreme (AE) routers.  My configuration is:
    Coax cable -> Comcast Xfinity cable modem -> ethernet to 16-port gigabit ethernet switch ->->-> ethernet to 3 Airport Extremes around the house direct connected with switch
    I have many wifi devices throughout the house (iPads, MacBooks, home automation devices) as well as direct-connected devices via ethernet (one PC connected to AE router).
    Each Airport Extreme router is set with these settings in the Airport Utility app: 
    Internet tab=  Connect using: DHCP
    Wireless tab=  Network mode: Create a wireless network
    Network tab=   Router mode: Off (Bridge Mode)
    I have attempted to put the Xfinity cable modem in bridge mode, and use the Airport Extreme to serve up the IP addresses, but still lost internet connectivity.
    I have also attempted to set the Network tab=> Router Mode to "DHCP and NAT" but get "Double NAT" error issues as well.
    I have tried using the Comcast DNS server addresses (75.75.75.75;75.75.76.76) setting on the Internet tab for the routers and do end up getting a green light, but NO internet connectivity.
    Lastly, I have tried using the Google DNS servers (8.8.8.8;8.8.4.4) setting on the Internet tab the routers giving me the No DNS servers amber light error and again, no Internet connectivity for either wifi-connected or even ethernet connected (directly to Airport Extreme router) devices (like my PC) despite getting a green light on the router.
    Any this point, it really seems that these AE routers are NOT compatible with the Xfinity cable modem or service… (and yes, I've tried power-cycling and restarting the modem, and then the AE routers, MANY times to little avail).
    Should I move one of these Airport Extreme wifi routers to before the switch, and have the other 2 in Bridge mode after the switch?  Do I need to setup a specific range of DHCP reservation addresses for each different AE router?
    Appreciate any insight anyone can share with this aggravating DNS server issue between Comcast & multiple Airport Extreme wifi routers.

    I do not see anything wrong with your basic setup.. the issue is indeed the WAN ports of the AE.. AC version are having problems with some network equipment.
    You have listed a stack of things you have tried.. but I want you to move the ethernet patch cable you use on each AE to its LAN port instead of WAN.
    Restart the airport when you do that.. and then see if it becomes stable.
    In bridge mode the airport moves the WAN port to LAN.. but the WAN port setup itself seems more problematic than the LAN ports.
    There are other methods we can try if this does not work.. but in the end.. I would be tempted to take the whole lot back to apple.. they need to start making equipment that works with standard modems and switches.
    BTW what brand is the 16 port switch?? Does it happen to be managed (smart type)?

  • MSN webtv and airport extreme basestation issue?

    Hello, My mother has an airport extreme M8930LL/A hooked up to a comcast highspeed internet modem by the wan port and a msn-webtv box hooked to the base station by the lan port. The problem(I know msn;)) is that when she uses the webtv is that webtv sometimes flashes off and on as if the webtv box is powering on off, but it seems more like the signal coming through the ethernet connection from the airport extreme basestation is powering on off. It also appears to be in sync with one of the lights flashing on the basestation. I forget which light as I have been sidetracked from this for a few weeks now and have just been able to get back to it. Any help would greatly be appreciated.
    Thank you,
    Message was edited by: electriczipper

    Hi, It appears that it is a comcast thing and nothing to do with airport or msn webtv. Still trying for a permanent solution as comcast came out and replaced a connection that resolved it temporarily.

  • Using an iBook G3 on and Airport Extreme Network

    Hi,
    We currently have an iBook G3 800 MHz (no airport card) and are planning to get a new superfast 24" iMac 3.06 GHz. My son will be getting a newer MacBook (assumedly with Airport Extreme built in) through school.
    My question: If we set up an Airport Extreme wireless network, will including the old iBook (since it has only non-Extreme Airport potential) slow the rest of the network down, and, if so, would the slow down be enough to notice?
    Would upgrading the OS on the iBook (currently 10.3.9) matter?
    Thanks,
    Rob S.

    Hi, Rob. Welcome to Apple Discussions.
    +If we set up an Airport Extreme wireless network, will including the old iBook (since it has only non-Extreme Airport potential) slow the rest of the network down+
    Yes.
    +would the slow down be enough to notice?+
    Probably not (at least for the internet). If you're swapping files between computers, it will slow that down on your network, but not troublesomely so (at least, not in my experience). The way I understand it, unless you have internet access in excess of 11 MB, you are not going to slow your internet experience down at all by having the iBook up and running on your network. We use ours on our 10 MB internet and don't see a slowdown with our newer computers when the iBook G3 is on the network.

  • Canon i550 won't print with MacBook and Airport Extreme

    Since we got a new MacBook, we upgraded our Airport Express (b/g) to Airport Extreme (n). Needed tech support from Apple to get the computers on the internet (something about the cable company switching IP addresses), which worked great, but since then the only problem is that I can't print wirelessly from the new MacBook to our Canon i550 printer, which is hooked up by USB to the Airport Extreme. (Ironically, when the internet wasn't working through the Airport Extreme, the one thing that DID work was printing wirelessly.) The other computer, a 2007 MacBook Pro, prints wirelessly with no problems, but I see that under "location" in the print utility it still has "Express" listed (on the MacBook I get the new network name, "Airport Extreme"). I've tried reselecting the printer in Bonjour, reselecting it in AirPort Utility under Printers, turning printer on and off, but no matter what, in the printer status box it just says "Connecting", and never actually prints. I just upgraded to 10.5.6 which still didn't help. Anyone have any thoughts? Thanks.

    Welcome to the discussions, Brian!
    Please work your way through the Apple Troubleshooting Guide to see if your HP might be compatible with the AirPort Express.
    Keep in mind that if your device is compatible, only printing is supported at the USB port on the AirPort Express. So, if you need to scan, copy, fax or check ink levels, etc., you will need to hook the device directly to your computer.

  • I have trouble opening PDF documents with Firefox. They will open using IE8 and with the older version of Firefox but not with the new version of Firefox.

    Specifically, I am trying to open brokerage statements with Charles Schwab. I go to the link using Firefox and click and all I get is a blank box with ABOUT: BLANK in the header at the top. Yet, I had no trouble viewing the statements with the older version of Firefox and I also have no problem viewing the document using Internet Explorer. Any help you can offer is appreciated. I would rather continue to use Firefox as my browser and not have to use IE.

    https://support.mozilla.com/en-US/kb/Using+the+Adobe+Reader+plugin+with+Firefox
    https://support.mozilla.com/en-US/kb/Opening+PDF+files+within+Firefox

  • 10.4.8 and Airport Extreme - wireless con. not showing up on boot up

    Ever since I installed 10.4.8, in order for my 2WIRE connecttion to show up in the "Internet Connect" drop menu on my desk top, I have to check off the "Internet Robustness" setting first, and only then will my airport extreme locate 2WIRE and connect.
    I've engaged - and disengaged to see if it made any difference - the preference for "enable interference robustness in the Airpor>options pane. Made no difference. It's not a huge deal, but I wonder why the change. Any ideas?

    Could be that a combination of the last OSX 10.4 security update and also
    the AirPort Extreme updates have some effects on these subtle or not so
    subtle differences in how the system works, now. Mine occasionally won't
    work correctly with my desktop iMacG4 unless the Robustness setting is
    turned on; and I have the nearby option to choose a wired connection
    through the AEBS on the wall by my desktop computer, too. My iBook
    seems to mostly just work; unless there is an AEBS or IP/DSL issue.
    That kind of problem never used to happen and I'd just lose the wireless
    without any understandable reason; at least now I know interference rob-
    ustness setting appears to make a difference when it unexpectedly quits,
    I have at least one more thing to toggle to see if I get it back; before I
    start in on the DSL modem or other settings inside the AirPort Setup Utility.
    The last thing if it does not work, is unplug the AEBS and/or ADSL unilt.
    But, if you use a small straightened paperclip in the reset hole, you'd
    have to check and rechoose settings in the AEBS; as it goes default.
    Seems to me, once I uploaded to the AEBS from the iBook that runs
    OSX 10.4.x, it was acting funky; but for awhile since another update
    was done, it seems to work OK. Since the odd behavior messed with
    the iMacG4 (10.3.9) I more often use it via ethernet from AEBS. The
    iBook sees the wireless better than the iMacG4. Since both of mine
    have Extreme wireless cards, I changed the AirPort's 802.11 to /g only.
    That helped a bit and the desktop Mac on wi-fi doesn't drop as much.
    I see no real answers to "fix" this; but there is some incidental evidence
    that some newer spec wireless base stations may be coming soon to
    an authorized reseller or through the authentic online source. Perhaps a
    new answer is out there, in new hardware and software. I hope an update
    will fix these little issues; I've had one AEBS for about three years and
    it used to just work fantastically with OS 9.2.2 and standard airport, with
    dialup. Then I brought in Jaguar in the machines I had then, and Panther;
    plus Tiger, and now two other Macintoshes plus a spare AEBS.
    Cross fingers?!

  • Windows 7 and Airport Extreme disk do not connect

    I have three windows computers (XP, VISTA & 7) and one mac mini all sharing a drive connected to my airport extreme. I can access the drive fine with computers except windows 7.
    My configuration on the airport was to prompt for a disk password, so I changed it to ask for username and password and I still cannot connect.
    I have tried to map it via \\10.0.1.1\Disk and also \\extreme\Disk neither work.
    I have been able to connect or at least it appears to connect by showing me the drive listed in windows 7, but none of the files are present. Windows xp and vista show the files fine and still can connect.

    But currently have it working with the Win 7 defaults of:
    1) "Send NTLMv2 response only" for "Network security: LAN Manager authentication level"
    2) "Require 128-bit encryption" for "Network security: Minimum session security for NTLM SSP based (including RPC) clients"
    also, my "Windows Search" is enabled.
    I might end up revisiting these ideas though, because if I disconnect the network drive from the PC and then try to remap it, I run into some of the same problems that occurred in the initial troubleshooting - in other words I cannot just map the drive, need to reboot.
    So the problem that I had in summary:
    - I had gotten the Airport Extreme shared USB drive to connect to the PC by first a reboot and then connecting via wireless to the Airport Extreme
    - If I disconnected from the shared drive on the PC, then I could not re-map it (I could get it back by the reboot / connect mentioned above): Windows was asking for "user name" and "password" when I went through the "Map network drive", following the ideas specified in "AirPort: How to mount an AirPort Extreme USB hard disk volume in Mac OS X and Windows" (http://support.apple.com/kb/HT1331?viewlocale=en_US)
    After more monkeying and searching around, I found that could fix this by:
    1) On the PC, go to Start, type "advanced share" in the search box. This will take you to "Change sharing options for different network profiles" (can also get there by going to Control Panel\All Control Panel Items\Network and Sharing Center\Advanced sharing settings).
    2) Once there, go down to the bottom "Password protected sharing" and click "Turn off password protected sharing". Save your changes.
    3) Disconnect / reconnect to your Airport Extreme - I am doing it via the primary (non-guest) wireless.
    Then, whenever I connect to the primary (non-guest) wireless on Airport Extreme, the share automatically maps itself. I can disconnect from it (the share) and it will disappear from under My Computer. To reconnect to it (the share), I just recycle the wireless connection. And, if I log on to the guest network, the share is not visible, which is how I would expect it to perform with my settings.
    In Control Panel Microsoft describes "Password protected sharing" as:
    When password protected sharing is on, only people who have a user account and password on this computer can access shared files, printers attached to this computer, and the Public Folders. To give other people access, you must turn off password protected sharing.
    Maybe I am just tired from pounding away at this (yes, still using the "Monkey Theory" analogy - it is actually listed as the "Infinite monkey theorem" on Wikipedia if you want to read about it) but the whole thing still doesn't make much sense to me.
    As far as why changing Network security policies may work for some and not others is a bit of a mystery. I did pursue this further and ran Wireshark while I changed these settings around. There were some differences in the "Negotiate Protocol Request" and "Negotiate Protocol Response" sequence, as would be expected but the end result for me was just keeping the default Win 7 values and making the changes mentioned above to get things working.
    Otherwise, in Wireshark, I could just continually see as the PC got rejected for an attempt to logon to the share with its credentials, which I could not effectively change via the "Map network drive".
    I also just ended up Turning off network discovery from the control panel (same location as mentioned above). Now, if I try to browse in the "Map network drive" , I get a popup that sates:
    "Network discovery is turned off. Network computers and devices are not visible. Please turn on network discovery in Network and Sharing Center."
    Yet, there is my nicely mapped Airport Extreme shared drive, sitting under My Computer, fully accessible and listed as a Network Drive. So, I am not sure what is really more baffling, the semantics or the technology that is at work underneath it.
    I would love to hear if anyone else can get things working by doing any of the above.
    Message was edited by: aprouser

  • Samsung CLP-315 and Airport Extreme, sporadically does not print

    Hi:
    I am using MacBook Pro, OS X 10.5.8, Dual-band Airport Extreme with v.7.4.2, and a Samsung CLP-315.
    Previously I had Airport Express and had trouble printing. I fixed it with the workaround using HP Jetdirect with address 10.0.1.1:9101. I then upgraded to Airport Extreme and that fix did not work. I deleted the printer from Print & Fax and added again with Bonjour. Since, it has been printing sporadically. Sometimes, it simply does not print. I have tried to pin down what causes it, but I have only been able to consistently reproduce the error when trying to print from Graphic Converter. Other applications print sporadically.
    I have tried to download the new drivers from Samsung, but that has not solved it. I have tried to recreate the workaround through HP Jetdirect, but I always get a "printer busy" error when printing (using both 9100 and 9101)
    I also tried to run FixAirportPrinter and although the application sees the printer when launched, after running the application the same symptoms remain.
    Any help on how to resolve this is greatly appreciated.
    Thanks,
    Rodrigo

    This is to say that I have exactly the same problem with a Samsung CLP-310 unit. I have 2 Books as below.
    My older powerbook has no problem printing to this printer. My newer Intel unit will not print.
    If I open Airport utilities on the 10.4 Powerbook and select "Base Station options" I can see the Samsung printer under USB devices. If I repeat the process on my 10.5 Intel unit and double-click on the Airport, the properties page shows the Samsung CLP-310 but it I go to USB devices they are empty.
    What gives? The SAME Airport only prints to a USB printer if it is sent from a Power PC Book?
    The Samsung CLP-310 is connected directly to the USB Airport output.
    Message was edited by: Eugene Baker1

  • Scripts works in Simulator and Apple DVD player but not on TV

    I have a basic project with two different tracks.
    The first one is video and audio. Plays "as is".
    The second has video, two audio and one subtitle. Depending on which button, the second Track should be played with different audio and with/without subtitles.
    (I use GPRM 1 to set the subs stream, GPRM 2 for the audio and GPRM 3 for menu button navigation).
    On the second Track I have a pre-script that sets the streams depending on the value of GPRM 1 and 2.
    Works fine in Simulator and in Apple DVD player, but not on the stand-alone player.
    Any idea what might be the issue here?
    in short:
    Button 1: Play Track 1 "as is" (audio 1, no subs)
    Button 2: Play Track 2, audio 1, subs on
    Button 3: Play Track 2, audio 2, subs off
    Button 4: Play Track 2, "as is" (audio 1, subs off)
    Menu button and End Jump should go to the corresponding menu button.
    Many thanks for your help.

    It is part personal preference, part artistic, part what makes the user experience the best so there may not be one "right" answer and I have often made menus one way than changed them when viewing the DVD for something that seemed to work better.
    Looking at you description I started playing with some ideas in my head and started typing them, then changed what I was writing
    It sounds like you want chapter selections for both track 1 and track 2? If so it may make sense to have the initial menu have Track 1 and Track 2 buttons which then link to sub menus where there is "Play All," selections for each section of each movie and one last button for the preferences.
    Alternatively you could also place the preferences selection button on the main menu, though since Track 1 does not sound like it really has preferences you need to make sure that users do not become confused and think they have turned something on/off and are not seeing these options when they thought they selected them when they play back Track 1.
    Also with 6 to 8 chapter markers you may be getting close to the point where scripting could make it easier if your selections are just to play the sections - in other words for track 2 four stories take care of the combinations Audio 1/Sub Off, Audio 1 Subs On, Audio 2 Subs Off, Audio 2 Sub On. If the chapter selection starts the track a scene then plays through you can target chapter markers in the story so 4 stories takes care of it. If you are just playing sections you would need 4 x 6 or 8 chapters - 24 or 32 stories roughly. But it is actually fairly quick to do - just set up the intial Play All with all subtitles and audio selections unchecked except for "1" then copy from there. Probably should take under 10-15 minutes or so
    Put a real quick thing together for a quick view of the tracks. I can flesh it out more if you like.
    http://www.dvdstepbystep.com/081107Sub.dmg
    The main menu will be the title menu, then the sub-menus (including the set up menus) can be placed in the same VTS as the applicable tracks which can help a bit with DVD performance speed. Since there is 6 to 8 chapter markers on a track each of the main sub-menus would have 8-10 buttons which can work in the design.

  • My Photoshop Elements 11 works with RAW from my Nikon D5100 but not with my D5200?

    Is there a download to cope with the greater number of Mbs in the D5200 image?

    Abeldacre wrote:
    Is there a download to cope with the greater number of Mbs in the D5200 image?
    Explanation here:
    http://forums.adobe.com/thread/1030798?tstart=0
    Each camera model has its own raw format. The  5200 format was issued after PSE11.
    http://helpx.adobe.com/creative-suite/kb/camera-raw-plug-supported-cameras.html
    http://helpx.adobe.com/x-productkb/global/camera-raw-compatible-applications.html
    So 3 solutions :
    - use the Canon software to convert to tiff files that can be edited by Elements editor
    - update to PSE12
    - (my advice) use the free Adobe DNG converter to batch convert your raw files to the DNG format. Your PSE11 will be able to edit them and you'll keep all the advantages of raw editing.
    The size of your raw files are not relevant here.

  • Can video chat with Aim users on a PC but not with Ichat users on Mac!

    Hello
    I am having the odd problem of being able to video chat with someone when they are using their pc running aim, but I cant chat with the same person when he on his Mac!
    I am running as DMZ behind a Linksys WRT54G wireless router.
    The problem is on my side because I cant chat with the test accounts either.
    I tried this after bothe forwarding and triggering all the ports that were suggested.
    I am stumped!

    Hi Lullah,
    This is going to be down to the Staelite connection.
    It has what is called latency.
    This adds an unexceptable delay in the passing of data at the start of the connection.
    Very few people have reported success.
    The things you can try are to fool the link into passing more intense data prior to starting a chat.
    If you have web pages try uploading a Pic of larger file to the site.
    Just as this finishes start up iChat
    You should also check that System Preferences > Quicktime > Streaming tab has the speed to match you download set.
    Hopefully (But no reported success) you may get iChat to see more bandwidth as you have just had the modem busy.
    Following the launch of iChat with a video chat request may be able to get that bandwidth.
    Realistically the 128 k upload even if you were getting close to it is very tight to the lowest point Apple say will work.
    Speed testing a 128 k service i likely to get a result of about 80% of the figure (102k) iChat will use about 80 % of what is left (you are down to about 83K). You are now below the 100k min.
    With regards to your LAN there are several things that may help if not set up already.
    Only have one device doing DHCP. The way routers work as compared to modems is that they pass all routing data though to the computers.
    This means the computers can be sitting in two subnets (1) from Modem to computer via router and (2) from Router. The computer can only display one of these IP addresses but can get confuse info regarding iChat.
    Do not use Port Forwarding or Port triggering, twice or together on the LAN. iCHAT does not like two lots of NAT (bath are forms of Network Address Translation [NAT]).
    Use UPnP where you can.
    IF you are trying to test this yur Mac to your PC you ahve to allow for the fact that the modem is handling two Video chats in effect. This means you need twice the minimum bandwidth (let alone the fact that ichat to AIM semms to like 50% more than Mac to Mac contacts.
    Sorry to be the bearer of so much doom and gloom.
    11:03 PM Tuesday; March 28, 2006

  • Not able to edit Yahoo Mail address book. Okay with Apple Safari's Yahoo Mail but not with Firefox's,

    Editing a contact in Yahoo Mail it always just "hangs" (doing nothing) when I am using Firefox. Editing the same account using Apple's Safari browser went through without any problem. It seems that Firefox interface with Yahoo caused this.

    Just found the answer (it's a reported bug) and a likely solution!
    Instead of dragging the group over to the 'To' box in a new email, the suggestion was to just start typing the name of the group. So far it seems to be working!!!

Maybe you are looking for

  • Bit of a strange question

    Hi guys, here goes - I have created a small movie in livetype (a title sequence) and have imported this into a new FCE project. The project also contains a number of still images. Now, I set the project up as I want it and have audio added, and can e

  • Installation of Adobe Acrobat Pro X from DVD stalls and does not continue?

    I recently purchased the DVD version of Acrobat Pro X for macintosh and the installation does not seem to progress?  It keeps adding time to the 'running package scripts' page.  I quit the installer and tried again and not it gets stuck again saying

  • Using MB_DOCUMENT_BADI on MB31

    Hi, I'm trying to use the BADI MB_DOCUMENT_BADI on MB31 (when saving document) to insert notification number on MKPF-XABLN (GR/GI Slip No). I created an Implementation of the BADI, the class and a method  IF_EX_MB_DOCUMENT_BADI~MB_DOCUMENT_UPDATE whe

  • Server with a frontend GUI

    I have an application which maintains a database of objects as an ArrayList. I'm trying to add a sort of background server, which would accept requests for information from this database and provide responses, and also be able to store new objects in

  • Call settings changed in one system

    Hi , I have changed my call settings from one system and skype used in other system for the same login doesn't reflect the same setting. Will the settings stpred in local not updated in the server. Also the IM msgs not able to view from the other sys