PCI USB2 Controller card conflicts with network card

I've installed a PCI USB2 controller card since my motherboard (IWill K266-R) only has support for USB1. However, the card seems to conflict with one of my network cards, because traffic on the internet-connected NIC is very slow, and often drops completely. Traffic to and from the other (local) NIC seems to work fine, though.
I have tried moving around all three cards in different PCI slots, I think I've tested almost every possible combination by now. I've also tried disabling as much as possible in BIOS, such as onboard sound, serial and parallel ports etc. I've tried lowering the FSB.
For now, I've removed the controller card, and is using the USB1 ports on the motherboard instead. This is very frustrating, though.
Does anyone have any suggestion on what I can try next? I've browsed forums, both this and others, but I haven't found any more hints on what to try. Could there be some setting in Arch that could affect these sorts of things?

"I guess the ATA100 card will work fine correct?"
If you mean large drive support, it may provide that or may require a firmware update to do so. You should check the manufacturer's web site for specifics. All ATA-133 cards do provide 48-bit LBA for large drive support. I'd return the Ultra ATA-66 card to the eBay seller, although many refuse to pay for return shipping, even when the mistake is their own, either through ignorance or deliberate misrepresentation. In cases such as this, it's sometimes more cost-effective to swallow the loss and keep the incorrect part.
"Will adding a jumper apply for a ATA100 card as well? I'll need a blue and gray ribbon correct?"
If you use an 80-conductor ribbon cable with color-keyed connectors, set the drive configuration jumper to CS and connect the drives to the cable as you wish (in terms of physical placement in the computer). If the ribbon cable doesn't have color-keyed connectors, set the jumper for the device connected to the end connector as Master and the drive (if any) connected to the middle connector as Slave.

Similar Messages

  • Installing Cisco E3000, conflict with Network Magic

    I have replaced, for security reasons, my old Belkin with the Cisco E3000.  The installation disk runs and then says will not configure router.  I tried Cisco Router chat but they say it is a Network Magic problem, because the software in the install disk conflicts with Network Magic.  I have checked my firewall (Sunbelt's Vipre) and did not see any problem.  I am running XP SP3.  I also uninstalled all the Belkin entries I can find, rebooted, and still it would not install.  Somewhere, in Network Magic, has to be the process in which I need. 
    Information to help in diagnosis:
    Network Magic version 5.5.9195.0-Pure0
    Cable Connection
    Cable modem is a Motorola, SB 5100
    Router I am trying to install:  Cisco E3000.  Since it won't setup, I can't give you any info
    Router Connection: Wired
    Ethernet port is a PCI Card
    Windows XP SP 3 with all updates
    Firewall from Sunbelt software, the Vipre product versions 4.0.3904, updated 30 minutes ago
    Vipre also applies to the Anti-Virus
    My physical locating is Western PA, USA
    I was able, with the router setting up, connect to the internet simply by plugging in the router to the modem and then PC.  Plugging in the router to the cable modem was part of the setup procedure.  Connecting to the PC was something I did via Network Magic.  This did not set up the router.

    jobanks wrote:
    I have replaced, for security reasons, my old Belkin with the Cisco E3000.  The installation disk runs and then says will not configure router.  I tried Cisco Router chat but they say it is a Network Magic problem, because the software in the install disk conflicts with Network Magic.  I have checked my firewall (Sunbelt's Vipre) and did not see any problem.  I am running XP SP3.  I also uninstalled all the Belkin entries I can find, rebooted, and still it would not install.  Somewhere, in Network Magic, has to be the process in which I need. 
    Information to help in diagnosis:
    Network Magic version 5.5.9195.0-Pure0
    Cable Connection
    Cable modem is a Motorola, SB 5100
    Router I am trying to install:  Cisco E3000.  Since it won't setup, I can't give you any info
    Router Connection: Wired
    Ethernet port is a PCI Card
    Windows XP SP 3 with all updates
    Firewall from Sunbelt software, the Vipre product versions 4.0.3904, updated 30 minutes ago
    Vipre also applies to the Anti-Virus
    My physical locating is Western PA, USA
    I was able, with the router setting up, connect to the internet simply by plugging in the router to the modem and then PC.  Plugging in the router to the cable modem was part of the setup procedure.  Connecting to the PC was something I did via Network Magic.  This did not set up the router.
    Hi jobanks,
    Call Network Magic Support for help.
    By phone: 888-812-9402
    Mon-Fri, 9am-5pm Pacific Time
    Sat-Sun, 11am-4pm Pacific Time
    (We're closed on most US national holidays.)
    thecreator - Running Network Magic version -5.5..9195.0-Pure0 on Windows XP Home Edition SP 3
    Running Network Magic version -5.5.9195.0-Pure0 on Wireless Computer with McAfee Personal Firewall Build 11.5.131 Wireless Computer has D-Link DWA-552 connecting to D-Link DIR-655 A3 Router.

  • SB Audigy Value card Conflict with Modem re-booting my

    My PC using Intel D95GAV M/B, 3.2GHz with XpSP2. On-board sound ok. Recently installed SB Audigy Value card. It is working perfectly. But with that card I can't use any modem function, any time if I dial or connecting to Internet or Outlook my PC gets re-boots. I already disabled on-board audio. different PCI slot tried. Then I replaced the Audigy card. Replaced the Modem. Audigy Value card tried with another 3 PCs. all are facing the same problem.
    Please Help me!
    4S7MD

    Unfortunately if you read the release notes for the Vista compatible driver it tells you not to use it on your particular sound card ;(?http://us.creative.com/support/downl...rtype=&x=2&y=7?Notes:
    DO NOT?install this driver for Sound Blaster Li've! 24-bit, Sound Blaster Audigy LS, Sound Blaster Audigy SE, or Sound Blaster Audigy Value.<However when you tell the site you have an Audigy Value card it directs you to these incompatible drivers
    go go Creative

  • Solaris9 x86 problem with network cards, ACPI, IRQs

    Hello!
    For the last two days I've been trying to solve the problem of Solaris9 x86 not being able to use my network card. I have tried with 3c905CX-TX-M, RealTek 8139 and Realtek 8029 and none of them works. The problem is the following:
    Everything is properly configured, networking etc., but the cards can only send and cannot receive packets. When trying to ping, the packets leave the NIC but none of the reponses are detected by NIC. When I check with 'kstat elxl' I can see that 'intr' is zero, and out_packets is increasing as it's sending packets.
    From the discussion forum I can see that this same problem has been known for several years. One of the conclusions is that Solaris x86 sucks at dealing with IRQ setup and that the best thing is to disable ACPI and 'PnP OS' option in BIOS. However, I've tried all releases of AMI bios and none them has neither of those options. I have played with various priority levels in BIOS but all that has accomplished is that the card, when first started, captures a few interrupts/packets but then stops again. This is usually just enough to finish the ARP exchange (arp -a shows the remote host).
    And of course, all the cards work just fine in WindowsXP and Linux. And all the cards work nice in another PC which runs the same Solaris 9 x86.
    My motherboard is Gigabyte 7VTXE. (The other one in which it works is ASUS P2B-DS).
    I would really appreciate help!
    Josip

    I had almost identical problem today on an HP Kayak - which happened to be dual CPU one. The fix
    set pcplusmp:apic_forceload = -1
    in /etc/system worked for me. The only drawback is that it also leaves the machine single CPU. AFAIK this (downloadable) S9x86 kit is licensed only for one CPU anyway, so I wonder if something has been fixed in the code to make sure it is not run on multi-CPU systems. Before the fix, mpstat showed thousands of interrupts on CPU0, both CPUs were constantly busy at about 70% and there was no network connection on a number of cards I tried (3Com 90x - elxl, Intel iprb, another one with Realtek 8139 was never recognized, so I did not bother too much to find if there is a fix for this); pinging out resulted in the hub port light blinking, nothing comes back.
    Anyway, the fix is good enough to test s9 for now; everything else seemed to be OK. If it may be of some use for somebody, don't go into the disk option of the Solaris Management Console; the machine in question had Windows 2003 server (RC2) installed before Solaris9, the disk tool decided that there was no label on the disk and asked to write it on; I clicked the 'cancel' button, but the partition table was irreversibly damaged, so I had to start from installing W2k3. My guess is that tool has been tested only with Sparc, so there is no issue with BIOS level partitioning there. BTW, system info of the SMC insists that the CPUs are Sparcs...

  • Want to check local wifi hotspots with network card

    I've been told that my new MacBook Pro comes with a wireless network card and that I can use it to check whether there are wifi networks around.  Is there a way find out info on local networks with my Mac?

    Well, it's not technically a card, it's built in, but it's easy.  First go to System Preferences (it's under your Apple Menu, top right corner), then click on Network.  Along the right side is an icon that says "Airport".  Click on that.  Then check off "Show AirPort status in menu bar".  On your menu bar, then you should see something that looks like a signal (which shows strength).  If you click on that, you will see all the hotspots near you.

  • HP Storage Management Pack Conflicts with Network Monitoring SNMP

    The HP Storage management pack that I installed requires starting the Windows SNMP services, which creates a conflict with SNMP used for SCOM network monitoring.  I am spinning up a second SCOM mangement server so I can split these functions. What would
    you recommend to split these functions across the two management servers?  Uninstall the HP Storage Management Pack, and install on the new server?  Or move the network monitoring to the second server?
    Thank you for your help!

    Does the HP Storage pack support resource pools? What I've found with these 3rd party packs that implement connector services is they do not provide true HA via SCOM resource pools - they are standalone systems with a connector service. This is true for
    the NetApp (DataONTAP) pack, and it's a huge disappointment.
    Vendors do this because they have an API, and they think the only way to implement discovery and monitoring in SCOM is to create a service that accesses the API - and then the service is basically a collector in this case, and typically has a handful of
    rules (sometimes just one rule) that scrape events on the management server and they are misinterpreted to be alerts coming from some instance.
    I turn green when I run into this type of problem, because all this can be accomplished with native modules or managed code that are designed to work very well with SCOM.
    I know this doesn't answer your question - it's more a way for me to express my distain for these type of packs.
    Jonathan Almquist | SCOMskills, LLC (http://scomskills.com)

  • Sound conflicts with video card

    I have the 845GLMS/GVMS series MS-6754 Motherboard and I have having some major conflicts between my GeForce FX 5200 PCI 256 MB video card and any sound that I run off the card -whether it be the AC97 sound off the board or my installed Create Audigy LS PCI card or my Create Soundblaster USB device.  What happens is that if I run a game like Doom 3 - with any audio enabled, the FPS slows down to 5-8 BUT if I turn all sound off, it goes up to 30-40 FPS and this is also true with other games.  I have all the latest drivers and the BIOS is as up to date as Live Update will let it.  What should I do???  HELP!!!!

    change the sound card to another pci slot..
    BTW which slot is the vid card in, it should be in the first available from the top..

  • Usb portable sound card conflict with a game called rise of lege

    can anyone help me with a conflict issue i have with my usb sound card and the game of rise of legends

    Great Question!
    To know the answer to this question you usually have to be knowledgeable with multiple series of ATI, Intel, AMD & NVIDIA graphics cards & CPUs but I have a couple ideas for you to save time.
    The first is to visit PassMark Software, there they have almost all desktop/notebook graphics cards & CPUs benchmarked in an easy to read graph with higher meaning better. When you have the chart up just do a find on the page and put in 4800+ for the CPU or X1800 for the graphics card depending on which chart you have up. That will you your line on minimum specs you will take on a machine. I think you will be happy with the results! =)
    Second, if you already have the machine in front of you go to the Game-O-Meter website and run its diagnostic, after it has given you a baseline just pick one of the hundreds of games available in their list to see if yours is qualified or not. Not only will this give you your answer for Singularity but any others you might have been wondering about.
    Hope this helps!
    I am an HP employee.
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.

  • Person That bosted a Conflict with Sound Card Please Read

    I am sorry, I was trying to click on your thread to read it and my mouse was slightly off and it clicked on the Delete Thread.  For some reason there is no longer a warning saying "Are you sure you want to delete this thread" it was just POOF Gone! (I have reported the bug to MSI, not that it helps you at all.)
    I am sorry but you will have to post it again.
    My Apologies,
    Richard

    Hi I am experiencing the same issue since that I have upgraded my osx to 10.6.8 yesterday !
    Basically , my mac pro freezes after 10-15 minutes and I have no choice but to reboot the computer which is extremely frustrating !!! It is not only doing this with logic 9 but also with safari (youtube) or anything osx related.
    For now I have just unplugged my duet and nothing happened so far.. I am going to try it on my macbook pro and see how it goes..
    I will update later.
    cheers

  • Error message 'memory card error' with SD card on C5180

    Photosmart C5180 displays 'memory card error' when SanDisk SDHC inserted.  (The card is not damaged, it's new & works in camera.)  I've been unsuccessful in finding  answers on HP site.  Any help most appreciated.  Thanks much.
    This question was solved.
    View Solution.

    Looking at the product specification, I see "High Capacity" (SDHC) memory is NOT supported on the device:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00701803&tmp_task=prodinfoCategory&lc=en&dlc=en...
    I also verified this with our group in San Diego - SDHC isn't supported.
    ~TechHelper7
    I work for HP.

  • ESATA card compatible with CF card reader

    Can anyone recommend an eSATA card that would be compatible with the Addonics flash card reader below:
    http://www.addonics.com/products/flash_memory_reader/aepddesu.asp

    Their page says any SATA card on any computer.
    The essential question is, "Do you want Mac Bootable" ??
    Then you are limited to a few cards by Sonnet and FirmTek, or if you have a 2008 Mac Pro or previous to using a "cheater" SATA cable off the "extra" Optical Drive SATA ports.

  • Network Card Driver

    Hello Dear All,
    I am new to Solaris 10 and I wud like share my problem with you guys.
    I have installed solaris 10 on my intel x86 machine. It's working fine. Only the issue is with Network Card.
    Following is My Hardware Profile...
    Mother Board :- Intel D945GCR
    Onboard Lan :- Intel(R) Pro/100 VE Network Connection.
    Externel Lan Card :- Silan sc92031 PCI Fast Ehternet Adapter.
    The above mention LAN cards are not getting installed and I have 64 bit Kernel and drives are of 32 bit.
    So kindly Help me to get correct driver and patch of Solaris10 for the same, as i had done lots of google but, I am not able to identify the correct one.
    Thanks lot to all for all your kind guidance and support in Past and Future.

    Hello Dear All,
    I am new to Solaris 10 and I wud like share my problem with you guys.
    I have installed solaris 10 on my intel x86 machine. It's working fine. Only the issue is with Network Card.
    Following is My Hardware Profile...
    Mother Board :- Intel D945GCR
    Onboard Lan :- Intel(R) Pro/100 VE Network Connection.
    Externel Lan Card :- Silan sc92031 PCI Fast Ehternet Adapter.
    The above mention LAN cards are not getting installed and I have 64 bit Kernel and drives are of 32 bit.
    So kindly Help me to get correct driver and patch of Solaris10 for the same, as i had done lots of google but, I am not able to identify the correct one.
    Thanks lot to all for all your kind guidance and support in Past and Future.

  • How to configure HP Designjet T610 network card.

    Dear All! i have HP Design jet T610 with network card HP JetdDirect 620N & now i want to configure my plotter on network, i checked plotter setting & go to connectivity panel but there is no option to give it static ip or host name etc. so can some please guide me how i configure my plotter via network?

    We have HP Designjet T610, it has already network interface card placing on the plotter, so i don't know that is Jetdirect or not?! How should i know that, also how to configure and include in the network? it saying "Jetdirect -> No" on the connectivity settings. Pls help? 

  • Network card config

    I cannot get the box running solaris to see any other computer or my internet gateway.
    When i try and go to network card config (via preferances), it brings up a wizard type thing, that has nothing to do with network card.
    Am i doing something wrong?
    Any help would be great. I'm pulling my hair out
    Cheers andy

    Are you trying to get an IP using dhcp or static IP.
    If your trying to use dhcp then make sure your hostname is in /etc/nodename
    and do a "touch /etc/dhcp.<int>" where <int> is the name of the driver for your interface.
    If your trying to do static then put the IP of the router in /etc/defaultrouter
    And your hostname in /etc/hostname.<int>
    And make sure you have an entry for your hostname in /etc/hosts and /etc/inet/ipnodes

  • Regarding Network card

    Hi Team
    I  just want to confirm a
    point..regarding network
    card..when I Start
    MMConsole root  it gets started also work process come to wait state but when I open the easy access screen and give any Tcode it says "work process terminated session restarted"...
    ok when I give some command in command prompt saying .....
    sqlplus /nolog then
    connect /as sysdba..
    it sometimes says
    connected to an idle instance and sometime says connected ...now if at all I go back to SAPGUI and when I login into Easy access screen it takes time to process the command and then it gives the same message "work process restarted  session terminated"....
    now One of my friend says there is some problem with network card ...So your database gets disconnected.Is it the same problem...plz suggest  a solution.
    manjula

    Hi,
    Problem may be anywhere, you need to follow complete check so that you can trace the error.
    First of all check whether your database is up or not, then check all processes from MMC and later on try to connect through GUI. If everything is working and still you face problem to connect then it may problem of your ports or may be network card.
    Hope this help
    Regards,
    Rajesh

Maybe you are looking for