Peer to Peer network error 0x80070035 the network path was not found

We are adding an XP computer to a peer to peer network with Vista machines.  The Vista machines can see the XP machine in the network but when clicking to get to share files, message comes up Windows cannot access \\XPcomputer.   The message adds that there may be a spelling error or that there may be a problem with the network.  But the error message is the one listed in the subject of this email.
XP machine is properly set to share folders and there is no other visible proble.  There is no message from the antivirus software so I am assuming the address is within the Antivirus acceptable range.  Antivirus is Norton 360.
Any suggestions...very frustrating... thank you

Hi,
Before we start, please access the following article. This KB article introduces our support policies for peer-to-peer network
Using Crossover Cables in Home or Peer-to-Peer Networks
http://support.microsoft.com/default.aspx?scid=KB;EN-US;278870
The error code 0x80070035 indicates that the network path is not found. This behavior occurs if the NetBIOS over TCP IP is not enabled in Windows Vista. Please follow the steps below.
1. Click "Start", input "NCPA.CPL" (without quotation marks) and press Enter.
2. Right click on the connection that you use for the local connection, and then click "Properties".
3. Click Continue button to verify the administrator permission.
4. Click to select "Internet Protocol Version 4 (TCP/IPv4)", and then click "Properties".
5. Click "Advanced" button in the open window. On the "WINS" tab, click to select "Enable NetBIOS over TCP/IP", and then click "OK" to save the setting.
The following article introduces NetBIOS over TCP/IP
NetBIOS over TCP/IP
http://technet.microsoft.com/en-us/library/bb727013.aspx
If the issue is not resolved, you may try to access the computer with \\[IP address] as a work around.

Similar Messages

  • I have downloaded a movie from ITunes.  It shows up in my video app.  When I go to play it I get an error message: "The requested URL was not found on this server". When I checked back on iTunes, where you click to rent or buy a movie it says "Downloaded"

    I have downloaded a movie from ITunes.  It shows up in my video app.  When I go to play it I get an error message: "The requested URL was not found on this server". When I checked back on iTunes, where you click to rent or buy a movie it says "Downloaded".  Any advice on what I can do in order to watch this movie that I rented a couple of weeks ago?

    Select the content which is causing a problem and use the 'Report a problem' button in Your Purchase History on your computer.

  • I am trying to authorize my computer and I get an error message: The required directory was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed. Help?

    I am trying to authorize my computer and I get an error message: The required directory was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed. Help?

    I used Terminal to change the permissions on the folder in question.  I followed the instructions in this article:
    iTunes: Missing folder or incorrect permissions may prevent authorization
    In my case, the folder was there, so I needed the command to change permissions on the folder, not to create one.   I was hesitant to use Terminal b/c I know that if I made an error I could wipe out my hard drive or render my computer unusable.  So to be SURE I didn't make an error, I carefully copied the command from that page and *pasted* it into Terminal.  Also, before I could do anything in Terminal, I had to go change my admin password (it had been a blank password before and that's not acceptable for making changes in Terminal).  I was just super careful when entering my password or doing anything else while Terminal was open (making sure I didn't accidently hit the spacebar or another key, etc.)  And it fixed the problem right away.
    What was confusing for me was that the iTunes error message said to change permissions in the FINDER, which is what I was trying to do.  It didn't mention Terminal.  What would really be helpful is if Apple included a link to a page like this in their error message.

  • HT1848 I cannot authorize my computer, I'm having this error message The required file was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed." please hel

    cannot authorize my computer, I'm having this error message The required file was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed." please help me

    Doublechecking. In the course of your troubleshooting to date, have you worked through the instructions from the following document?
    iTunes: Missing folder or incorrect permissions may prevent authorization

  • I keep getting this error message The required file was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed.

    I keep getting this messae when I try to share itune to my new mac The required file was not found or has a permissions error. Correct this permissions problem and try again, or deauthorize this computer if the permissions cannot be changed.

    Doublechecking. In the course of your troubleshooting to date, have you worked through the instructions from the following document?
    iTunes: Missing folder or incorrect permissions may prevent authorization

  • Error -5093 "The analysis library was not found" in 64 bit project. But the analysis library is found in 32 bit project

    Hello,
    I'm using the Labwindows/CVI  2010 Full Development system, in a Windows 7 professional 64 bits computer. So, The analysis library is installed (see in the attached file), and the Option Analysis from the Customize library menu is selected.
    I'm using several function from analysis library  (WhiteNoise, MaxMin1D, LinFit, etc). The projects in 32 bits work very well. In 64 bits project  there is not linkage error, the exe is created, but there are errors like that:
    Function WhiteNoise: (return value == -5093 [0xffffffffffffec1b]). The analysis library DLL was not found or could not be loaded.
    the same for the other analysis library functions.
    how to do to use the analysis library in 64 bit projects, it's the analysis library 64 bit compatible?
    thanks in advance
    Solved!
    Go to Solution.
    Attachments:
    AnalysisLibraryInstalled.jpg ‏220 KB

    Hi DansatB,
    thanks you for posting on this forum !!
    Yes, the advanced analysis librairy is 64 bits compatible. i can do the test on my computer on CVI 2013.
    i think it will be great to correctly uninstall your CVI version ans all install again.
    Regards
    Aurélien Corbin
    National Instruments France
    #adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
    Cahiers de vacances de NI
    Présentations en ligne : 12 fondamentaux à réviser, du 9 juillet au 29 aoû...

  • I keep getting "error 404 the requested URL was not found on the server. Thats all we know" message. Any idea how I can fix?

    I have tried to reset firefox and I have attempted to disable all my extensions, but keep getting this error message half the time i try to click on a new link. Any help?? Thanks!!

    Select the content which is causing a problem and use the 'Report a problem' button in Your Purchase History on your computer.

  • While accessing my iTunes an error message comes up saying; The requested URL was not found on this server

    While trying to access my library in iTunes, I receive an error message; The requested URL was not found on this server. This only happens with my older songs, but not with the ones I have most recently added? Any thoughts?

    Select the content which is causing a problem and use the 'Report a problem' button in Your Purchase History on your computer.

  • Recorded Videos after Sync: The requested URL was not found on this server.

    A few days ago, i recorded a couple of videos. They were saved properly and i could watch them after it in the Camera Roll of my iPhone. Because my memory was almost full, i connected my iPhone to my MacBook and synchronized about 900 old pictures with iPhoto and selected to delete the pictures after the sync. I did not select the recently recorded videos.
    After the sync, i opened the Camera Roll on my iPhone and tried to watch the videos again. But now, they all have a grey icon and it says the duration is 0:00 minutes. When i click on a video, it shows me the following error message:
    The requested URL was not found on this server.
    When i connect my iPhone to iTunes, it says that there is about 350 MB of "Documents and Data" on my phone that I have no idea where it is coming from. Do you think it is possible that the videos are still saved on my phone but my phone doesn't recognize it as videos and can't assign it to the icons in the Camera Roll? Do you have any tips how I can access the videos in case they are still saved somewhere on my iPhone?
    Thank you very much in advance for your help and tips!

    I have the same problem too!! I was deleting some photos and videos in my phone when the next picture I swiped to was a blank picture with JPG in the middle~ after I closed camera roll and reopened it my photos and videos after that picture are all gone~ and I'm left with 3 videos I took about 30 mins before with 0:00 and when I tried to play them the message popped up saying "requested URL cannot be found on this server" T^T does anyone have a solution to this problem?

  • Error code: 0x80070035 The network path was not found

    "Error code: 0x80070035 The network path was not found" while trying to access another PC running Windows 7 Ultimate I searched and read dozens of similiar posts to try to resolve this issue with no success.
    The situation is, I have a router in home with 4 PC's connected. My central PC is running Windows 7 Ultimate. The others are Windows 7 Ultimate again, and 2 running XP Pro. No special Firewalls, just have Windows Firewall enabled on all PC's, and am running KasperskyInternetSecurity2010 on all. (Have disabled these on all PC's and tried to view/connect and it didnt make a difference, same error)
    Fact one: not attempting a Homegroup connection at all, just simply wishing to connect in a basic network environment where I can drag and drop files between all PC's in my Home Network or in my house , however its considered. But on the Windows 7 I am unable to view either of the XP's only the other Win7, and when I try to access that one is when I get the "Error code: 0x80070035 The network path was not found".  
    Furthermore, while troubleshooting the problem I opened a Command Prompt in all computers, then an "ipconfig" to view each ip address. Then began to ping each machine to determin connectivity. Which resulted in partial success. My main Win7 machine (which i am on now) was able to ping successfully to all machines. But all other machines were unable to ping to me (main Win7). with a 100% loss.
    So at least I determined this is most likely a helpful fact in resolving this. Going into "services.msc" I made sure that all the obvious services are started and running:
    DCHP Client, Homegroup Listener, Homegroup Provider, Link-Layer Topology Discovery Mapper, NetTcp Port SHaring Service, Network Connections, Network List Service, Network Location Awareness, TCP/IP NetBIOS Helper
    All strarted and running in Automactic mode.
    Not sure what other information I can give at this point, to help assist in fixing this problem. Please dont hesitate to ask for me for more info if needed. Ready and willing to try anything to get this working, except for reinstalling the OS. All my programs work great and do not wish to go through the drama ao reinstalling all my programs and activating them and redoing all my Adobe settings and CAD settings.
    Someone please help !

    Hi,
    In addition, I would like to suggest the following:
    Enable NetBIOS over TCP/IP:
    1.    Go to “Control Panel\Network and Internet\Network Connections”.
    2.    Right-Click on the connection and choose Properties.
    3.    Click “Internet Protocol (TCP/IP) Version 4” in the list.
    4.    Click Properties, and then click Advanced.
    5.    On the Advanced TCP/IP settings windows, go to “WINS” tab.
    6.    Under NetBIOS setting, click “Enable NetBIOS over TCP/IP”, and then click OK.
    Thanks.
    Nicholas Li - MSFT

  • Error Code 0x80070035 - The network path was not found, Windows Server 2008 SP2

    I have bee receiving following "error code 0x80070035 - The network path was not found" when trying to open file shares in both directions using Windows Server 2008 Standard SP2 at both ends. The issue is identical to the KB article KB958285, however the hotfix is only valid up to but not including SP2. One of the servers in question has moved several times between 2 subnets seperated by a VPN. I have tried changing settings in and around the local NIC/DNS Suffix and in the network connection sharing centre, but with no luck. Firewalls are turned off at both sites, and pings and AD queries are successful (one server is a DC). DNS is also working correctly at both sites. Any help/suggestions would be appreciated.
    Richard

    I thought I would add in another scenario, since this link came to the top of my list in the search engine.
    We are running 2008 R2 with SP1 (it happened without SP1 as well)
    We could not map using UNC (IP, FQDN, or netbios name).  We could ping access the other servers via other utils like event viewer and services.msc but just could not map.
    In our case it turned out to be a VMWARE issue but we still had to make a regedit change first
    You have to go to regedit HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\NetworkProvider\Order\
    And add LanmanWorkstation to Providerorder
    I found on a Citrix board that citrix has an issue with this as well
    If you're running VM  here is an additional step you should do as well
    When you upgrade VMware Tools installed with HGFS from ESX 3.x to ESX 4.x, the HGFS driver may not get uninstalled properly. In this case, the virtual machine's network Provider Order tab in Network Connections
    > Advanced > Advanced Settings displays incorrect information and the virtual machine may lose network connectivity.
    To avoid this issue, uninstall VMware Tools 3.x before installing VMware Tools 4.x.
    To workaround this issue, if you have already upgraded VMware Tools:
    Click Start >
    Run, type regedit, and click OK. The Registry Editor window opens.
    Navigate to
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\NetworkProvider\Order\.
    Delete the reference to
    hgfs.
    Reboot the virtual machine.
    We found that if you strip out the HGFS, you do not have to reboot for the provider order tab to come back
    I hope that this saves people a lot of time.   I spent days researching this.
    This was the solution for me on 2008 R2 DC w/ Exchange.  I do not have VMWare installed but do have Hyper-V.  Thank you so much!

  • Vista - The network path was not found 0x80070035 - Leopard SMB

    Hello,
    This is driving me crazy. I have Samba enabled and configured properly on my Mac. My XBOX in XBMC can see and access the shares from the Mac perfectly. Vista shows an icon in the My Networks screen for the Mac, but when I double click it I get "The network path was not found" error code 0x80070035. I've already set Vista to work with NTLMv1 correctly. What else can I do? Or is this hopeless? I really wanted my Mini to work as a media server since I have it on all the time anyway.
    This is on Leopard 10.5.6.

    What does C:\ConfigMgrSetup.log tell?
    Torsten Meringer | http://www.mssccmfaq.de

  • When I try to open up a PDF document, i get the following error message: "There was an error opening this document. The network path was not found" AArrgh please help as I need to open up my documents. Thanks.

    When I open up a PDF Document all i get is an error message saying: "There was an error opening this document. The network path was not found" I dont know how to fix this, so looking for some advice please, as I really need o open up my documents.
    Thank for any help.

    The documents I’m trying to read are already saved on my computer, under various different headings, I know that we have a server, so I only assume these documents are saved on here, as I said before I’m not good with all this techno stuff. I do my work each week ( on a payroll system) and save the documents for each company, they automatically go to the correct place. I never request for them to be saved in a certain place ( well not that I’m aware of) . I then on occasions need to open up this information, it is then that I can’t read or open the documents. We do have a tech help, but they are off sick until the 5th Jan, hence me trying to work out if I can fix this problem through this help site. Its ADOBE Reader that I’m trying to use.

  • SCOM agent install fails Error 80070035 - the network path was not found

    I have deployed SCOM 2012 agents to most servers (2008, 2008 R2, 2012, 2012R2) in our estate but some either fail to install or are not monitored. I assume the two problems are related, but for now I am concentrating on the servers that fail completely.
    Installation is from the Discovery Wizard and I have about 20 servers that fail of various server versions.
    So looking at one specific server that is failing to install the agent - a 2008 standard service pack 2
    The firewall in on and file and printer sharing is enabled for domain, remote administration is enabled for domain
    I added a specific rule to allow TCP 5723 and 5724
    DCOM is enabled
    I can Ping the target server from the SCOM server by both name and FQDN - both return the same IP and our DNS server has only one entry for this server
    I can browse to the admin share \\server\C$ from the SCOM Server, using the same account that I specify for the agent install that is a domain admin with rights on this server (and on the other servers the agent
    did install to) and the server has plenty of disk space available
    I am not sure what else to look at so would welcome any ideas
    Thanks

    Hi Petro,
    I have a Agent installation failure cheat sheet, For your error 80070035 it is said to perform a manual installation.
    So i would like to understand which version of SCOM is this ? 2007 R2 or 2012 or 2012 r2 ?
    Also check if your agents have the WMI service started and enabled ?
    Also if yours is a SCOM 2007 R2 do you have a RMS & MS in your management group ? If yes then Pushing the agent installation from MS may cause such issue. So would suggest you push the installation from RMS.
    Also check if your Network connectivity meets the minimum requirement as recommended by SCOM. Below is applicable for Both SCOM 2007 R2 & SCOM 2012 & 2012 R2.
    Component A
    Component B
    Minimum Requirement
    Root management server or management server
    Agent
    64 Kbps
    Root management server or management server
    Agentless
    1024 Kbps
    Root management server or management server
    Database
    256 Kbps
    Also check if you have any Anti virus / Firewall which is blocking the install / communication. If yes disabe or add the "Monitoringhost.exe to the safe list or what your feature is.
    Check if you have another IP assigned to the NIC card and remove it tempraurly andchecl.
    Also post the event logs of the Agents which are in not monitored state for analysis.
    SCOM Agent installation failure error codes
    Error
    Error Code(s)
    Remediation Steps
    The MOM Server could not execute WMI Query "Select * from Win32_Environment where
    NAME='PROCESSOR_ARCHITECTURE'" on computer server.domain.com
    Operation: Agent Install
    Install account: domain\account
    Error Code: 80004005
    Error Description: Unspecified error
    80004005
    1.  Check the PATH environment variable.  If the PATH statement is very long, due to lots of installed third party software - this can
    fail.  Reduce the path by converting any long filename destinations to 8.3, and remove any path statements that are not necessary.
    2.  The cause
    could be corrupted Performance Counters on the target Agent.
    To rebuild all Performance counters including extensible and third party counters in Windows Server 2003, type the following commands at a command
    prompt. Press ENTER after each command.
    cd
    \windows\system32
    lodctr /R
    Note /R is uppercase.
    Windows Server 2003 rebuilds all the counters because it reads all the .ini files in the C:\Windows\inf\009 folder for the English operating system.
    How to manually rebuild Performance Counter Library values
    http://support.microsoft.com/kb/300956
    3.  Manual agent install. 
    The MOM Server could not execute WMI Query "Select * from Win32_OperatingSystem" on
    computer “servername.domain.com”
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: 800706BA
    Error Description: The RPC server is unavailable.
    8004100A
    800706BA
    1.  Ensure agent push account has local admin rights
    2.  Firewall is blocking NetBIOS access
    3.  Inspect WMI health and rebuild repository if necessary
    4.  Firewall is blocking ICMP  (Live OneCare)
    5.  DNS incorrect
    The MOM Server failed to open service control manager on computer "servername.domain.com". Access is Denied
    Operation: Agent Install
    Install account: DomainName\User Account
    Error Code: 80070005
    Error Description: Access is denied.
    80070005
    80041002
    1.  Verify SCOM agent push account is in Local Administrators group on target computer.
    2.  On Domain controllers will have to work with AD team to install agent manually if agent push account is not a domain admin.
    Disable McAfee antivirus during push
    The MOM Server failed to open service control manager on computer "servername.domain.com".
    Therefore, the MOM Server cannot complete configuration of agent on the computer.
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: 800706BA
    Error Description: The RPC server is unavailable.
    800706BA
    1.  Firewall blocking NetBIOS ports
    2.  DNS resolution issue.  Make sure the agent can ping the MS by NetBIOS and FQDN.  Make sure the MS can ping the agent by NetBIOS
    and FQDN
    3.  Firewall blocking ICMP
    4.  RPC services stopped.
    The MOM Server failed to acquire lock to remote computer servername.domain.com. This means there is already an agent management operation proceeding
    on this computer, please retry the Push Agent operation after some time.
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: 80072971
    Error description: Unknown error 0x80072971
    80072971
    This problem occurs if the LockFileTime.txt file is located in the following folder on the remote computer:
    %windir%\422C3AB1-32E0-4411-BF66-A84FEEFCC8E2
    When you install or remove a management agent, the Operations Manager 2007 management server copies temporary files to the remote computer. One
    of these files is named LockFileTime.txt. This lock file is intended to prevent another management server from performing a management agent installation at the same time as the current installation. If the management agent installation is unsuccessful and
    if the management server loses connectivity with the remote computer, the temporary files may not be removed. Therefore, the LockFileTime.txt may remain in the folder on the remote computer. When the management server next tries to perform an agent installation,
    the management server detects the lock file. Therefore, the management agent installation is unsuccessful.
    http://support.microsoft.com/kb/934760/en-us
    The MOM Server detected that the following services on computer "(null);NetLogon" are not running. These services are required for push
    agent installation. To complete this operation, either start the required services on the computer or install the MOM agent manually by using MOMAgent.msi located on the product CD.
    Operation: Agent Install
    Remote Computer Name: servername.domain.com Install account: DOMAIN\account
    Error Code: C000296E
    Error Description: Unknown error 0xC000296E
    C000296E
    1.  Netlogon service is not running.  It must be set to auto/started
    The MOM Server detected that the following services on computer
    "winmgmt;(null)" are not running
    C000296E
    1.  WMI services not running or WMI corrupt
    The MOM Server detected that the Windows Installer service (MSIServer) is disabled on computer "servername.domain.com". This service is
    required for push agent installation. To complete this operation on the computer, either set the MSIServer startup type to "Manual" or "Automatic", or install the MOM agent manually by using MOMAgent.msi located on the product CD.
    Operation: Agent Install
    Install account: DOMAIN\account
    Error Code: C0002976
    Error Description: Unknown error 0xC0002976
    C0002976
    1.  Windows Installer service is not running or set to disabled – set this to manual or auto and start it.
    The Agent Management Operation Agent Install failed for remote computer servername.domain.com.
    Install account: DOMAIN\account
    Error Code: 80070643
    Error Description: Fatal error during installation.
    Microsoft Installer Error Description:
    For more information, see Windows Installer log file "C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameAgentInstall.LOG
    C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameMOMAgentMgmt.log" on the Management Server.
    80070643
    1.  Enable the automatic Updates service…. Install the agent – then disable the auto-updates service if desired.
    Call was canceled by the message filter
    80010002
    Install latest SP and retry. One server that failed did not have Service pack installed
    The MOM Server could not find directory \\I.P.\C$\WINDOWS\. Agent will not be installed on computer "name". Please verify the required
    share exists.
    80070006
    1.  Manual agent install
    Possible locking on registry?
    http://www.sysadmintales.com/category/operations-manager/
    Try manual install.
    Verified share does not exist.
    The network path was not found.
    80070035
    1.  Manual agent install
    The Agent Management Operation Agent Install failed for remote computer "name". There is not enough space on the disk.
    80070070
    1.  Free space on install disk
    The MOM Server failed to perform specified operation on computer "name". The semaphore timeout period has expired.
    80070079
    NSlookup failed on server. Possible DNS resolution issue.
    Try adding dnsname to dnssuffix search list.
    The MOM Server could not start the MOMAgentInstaller service on computer "name" in the time.
    8007041D
    80070102
    NSlookup failed on server. Possible DNS resolution issue.
    Verify domain is in suffix search list on management servers.
    The Agent Management Operation Agent Install failed for remote computer "name"
    80070643
    1.  Ensure automatic updates service is started
    2.  Rebuild WMI repository
    3.  DNS resolution issue
    The Agent Management Operation Agent Install failed for remote computer "name". Another installation is already in progress.
    80070652
    Verify not in pending management. If yes, remove and then attempt installation again.
    The MOM Server detected that computer "name" has an unsupported operating system or service pack version
    80072977
    Install latest SP and verify you are installing to Windows system.
    Not discovered
    Agent machine is not a member of domain
    Ping fails
    1.  Server is down
    2.  Server is blocked by firewall
    3.  DNS resolving to wrong IP.
    Fail to resolve machine
    1.  DNS issue
    The MOM Server failed to perform specified operation on computer "name". Not enough server storage…
    8007046A
    1.  This is typically a memory error caused by the remote OS that the agent is being installed on.
    There are currently no logon servers available to service the logon request.
    8007051F
    1.  Possible DNS issue
    This installation package cannot be installed by the Windows Installer service. You must install a Windows service pack that contains a newer version
    of the Windows Installer service.
    8007064D
    1.  Install Windows Installer 3.1
    The network address is invalid
    800706AB
    Possible DNS name resolution issue.
    Tried nslookup on server name and did not get response.
    Verify domain is in suffix search list on management servers.
    The MOM Server failed to perform specified operation on computer servername.domain.com
    80070040
    1.  Ensure agent push account has local admin rights
    The MOM Server detected that the actual NetBIOS name SERVERNAME is not same as the given NetBIOS name provide for remote computer SERVERNAME.domain.com.
    80072979
    1.  Correct DNS/WINS issue.
    2.  Try pushing to NetBIOS name
    Gautam.75801

  • WinRM cannot process the request. The following error occured while using Kerberos authentication: The network path was not found.

    I have two forests with a transitive on-way trust between them: PROD -> TEST (test trusts PROD). I had previously had kerberos authentication working with winrm from PROD to machines in TEST. I have verified the trust is healthy, I also verified users
    in TEST can use WINRM with kerberos just fine. Users from PROD cannot connect via kerberos to machines in TEST with winrm.
    I have verified the service has registered the appropriate SPNs. I ran dcdiag against all my PROD and TEST domain controllers and didn't find anything that would prevent kerberos from happening. I even tried disabling the firewall entirely on my TEST dcs
    but that didn't gain me anything.
    I've enabled kerberos logging but only see the expected errors such as it couldn't find a PROD SPN for the machine, which it shouldn't from what I understand, it should go to the TEST domain and find the SPN from there.
    I'm really out of next steps before I call PSS and hope someone here has run into this and could provide me some next steps.
    PowerShell Error:
    Connecting to remote server failed with the following error message : WinRM cannot process the request. The following error occured while using Kerberos authentication: The network path was not found.  
     Possible causes are:
      -The user name or password specified are invalid.
      -Kerberos is used when no authentication method and no user name are specified.
      -Kerberos accepts domain user names, but not local user names.
      -The Service Principal Name (SPN) for the remote computer name and port does not exist.
      -The client and remote computers are in different domains and there is no trust between the two domains.
     After checking for the above issues, try the following:
      -Check the Event Viewer for events related to authentication.
      -Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use HTTPS transport.
     Note that computers in the TrustedHosts list might not be authenticated.
       -For more information about WinRM configuration, run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic.
        + CategoryInfo          : OpenError: (:) [], PSRemotingTransportException
        + FullyQualifiedErrorId : PSSessionStateBroken
    winrs Error:
    Winrs error:
    WinRM cannot process the request. The following error occured while using Kerberos authentication: The network path was not found.  
     Possible causes are:
      -The user name or password specified are invalid.
      -Kerberos is used when no authentication method and no user name are specified.
      -Kerberos accepts domain user names, but not local user names.
      -The Service Principal Name (SPN) for the remote computer name and port does not exist.
      -The client and remote computers are in different domains and there is no trust between the two domains.
     After checking for the above issues, try the following:
      -Check the Event Viewer for events related to authentication.
      -Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use HTTPS transport.
     Note that computers in the TrustedHosts list might not be authenticated.
       -For more information about WinRM configuration, run the following command: winrm help config.

    Hi Adam,
    I'm a little unclear about which SPNs you were looking for, in which case could you confirm you were checking that on the computer object belonging to the actual destination host it has the following SPNs registered?
    WSMAN/<NetBIOS name>
    WSMAN/<FQDN>
    If you were actually trying to use WinRM to connect to the remote forest's domain controllers, then what you said makes sense, but I was caught between assuming this was the case or you meant another member server in that remote forest.
    Also, from the client trying to connect to this remote server, are you able to telnet to port 5985? (If you've used something other than the default, try that port)
    If you can't, then you've got something else like a firewall (be that the Windows firewall on the destination or a hardware firewall somewhere in between) blocking you at the port level, or the listener on the remote box just isn't working as expected. I
    just replied to your other winrm post with steps for checking the latter, so I won't repeat myself here.
    If you can telnet to it and the SPNs exist, then you might be up against something called selective authentication which has to do with how the trust was defined. You can have a read of
    this to learn a bit more about selective trusts and whether or not it's affecting you.
    Cheers,
    Lain

Maybe you are looking for

  • Can any one tell how to create pivot table

    Hi , Am trying to create a pivot tabel in the MDM Import Manager. Iam able to see the preview of the pivot table which i want to create. But when i try to click "OK" button, an error message getting displayed like... "The new table cannot be created

  • How can I shuffle individual playlists?

    Can I set my iPod Classic (newest 160 GB model) to shuffle songs within an individual playlist? The "Shuffle Songs" setting only shuffles EVERYTHING!

  • Disabling auto-sync, turning on "manually manage songs"

    Just so everyone here knows, I had an iPod mini which I managed manually. I got the new iTunes, and plugged in my ipod. It said it was "updating", and I couldn't figure out how to make it stop. I thought it was going to delete my music and sync it wi

  • Exception sending serialised data from servlet to applet

    Hello, I have a servlet that sends periodically a serialised object to an applet, under a http get request. it works fine, but if I force the comunication not waiting too much between requests, I am getting this anoying exception: java.io.StreamCorru

  • Tiger quitting unexpectedly while my CD plays

    When I slot my CD into my slotdrive, there's this "cluck, cluck, cluk" sound until the CD is fully loaded. Does it happen to anyone else? It den decided to hum so loud sometimes... So I sent it for repair. Apparently, I was told they got it replaced.