Perplexing Wireless Router Issue! Please Help!

OK Guys and Girls, I could really use some help.  I have a wireless router Mod. WRT54G ver. 2.0, and yes it has the firmware upgrade. The problem that I am current having is this, my computer can connect to the router no problem, and  i  can access the settings too, but it will not let me access the internet at all. It's not the cable modem because I can hook up my laptop to it and get internet.  So in short the router isn't, for some strange reason, letting my computer access the internet but the router can access the web.  Please any suggestions are welcome. Thank you in advanced.

Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter.
When it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

Similar Messages

  • I am having some serious wireless networking issues - please help!

    I had a working wireless network setup in my home until the laptop was dropped and the hard drive needed to be replaced.  The network consists of the laptop, desktop and wireless printer.  I am now unable to get my wireless network up and running again.  Is there anybody that can walk me through this.  Right now I have the laptop hardwired to the cable modem so I am able to use the internet.
    Please help!!!!!! 

    1. Go to Wireless. Set using Manual Config.
        Mode = Mixed
        SSID = Create your own SSID
        Channel = 9
        Broadcast = Enabled
    2.Go to Wireless Security
        Security = WPA Personal
        Passphrase = Type your 8 character long password
    3. Go to Security. Disable Block/Filter WAN Request
    4. Check if you are still online wired.
    5. Connect your laptop to the wireless network
    Regards,
    Lord Maxthor

  • Installed iOS 5.0 and wifi will not stay up on my phone and only way to reset it is power reset my wireless router? Please help this is driving me mad!!!!

    Have iPhone 4 just installed iOS 5.0.1 and wifi will not
    Stay up on my phone even though router is 10 feet away
    And cannot recover wifi except by resetting router never. Asks for
    PW etc? Plus battery life is reduced on this iOS?

    Try a SMC reset:
    http://support.apple.com/kb/HT3964
    Try a NVRAM/PRAM reset:
    http://support.apple.com/kb/HT1379
    If no joy, take it back, and take full advantage of your warranty!
    You also may want to let Apple know about this as well:
    http://www.apple.com/feedback//
    I wish you the best

  • Mid 2010 15" MBP i5 A1286 POWER ISSUE-PLEASE HELP-

    The MBP works fine when mains connected but the only issue is every time I take the charger out it shuts down on me!!! So I have checked with a multitester & looks good the only thing i find hard to check for power is the battery itself as its hard to get a good connection, also I took to local Apple store & they checked with a new battery but said its still same issue so the guy disconnected nearly all the connecters off to check if they causing issue & he said now the battery is charging.
    So they still have the laptop to do further tests etc, but I’m not sure what could be the problem hear as maybe there is some component which is bad so the battery’s not charging or what else could be the issue please help & advice as I’m really confused as if it was something to do with the logic board then surely it would not even charge even after checking with the multitester or like Apple genius done by disconnecting other components...
    ANY HELP OR ADVICE WOULD BE HELPFULL,
    THANKS GUYS

    THANKS FOR THE HELP GUYS!!! BEEN AROUND 5 DAYS & NOT ONE PERON HAS HELPED...
    BUT YEAH THANKS AGAIN...
    WASTE OF TIME THIS IS...

  • Trackpad Issue - Please Help!

    Hi there,
    Hope you can help me out here.
    I've recently purchased a 15" i7 Macbook pro. The machine is but 3 weeks old &, of course, very well looked after.
    A few days ago, the built-in trackpad started behaving eratically. Cursor moving by itself, not responding to touch, clicking and opening things involuntarily. Not good at all. Many users seem to have had this exact same issue.
    These problems seemed to miraculously stop after a few re-boots and possibly a software update? I really couldn't tell you what resolved the problem.
    Unfortunately I now have a totally different problem.
    There is a thin, possibly 8 to 10mm horizontal strip across the centre of the trackpad that no longer responds to touch. If I move my finger from the botom of the trackpad upwards (or vice versa), the cursor will stop momentarily as it passes over the horizontal strip. The buttons are fine and the rest of the trackpad is fine. For the moment, I've increased the cursor acceleration so that I can at least navigate round the screen with a smaller area of the trackpad. USB magic mouse seems to work fine.
    If anyone else has experienced this &/or found a solution for this issue, please help me out here. I have rifled through endless threads about MBP trackpad issues with little success & do not live close to an apple store/genius bar.
    This is a 3 week old machine that cost me a small fortune. To be getting software/hardware issues so early on in it's lifespan is really rather worrying for the future.
    Appreciate your help here.
    J

    I'm not sure what caused this, but I extended my lunch break and drove the machine down to the Westfield apple store. I didn't have an appointment with the Genius Bar but I managed to persuade one of the staff to speak to a technician in the workshop. She came back into the store and told me that they had replacement trackpads and that , considering the machine was only 3 weeks old, the technicians kindly sandwiched the repair into their timetable at zero cost. 2 Hours later, I now have a perfectly functioning trackpad/machine.
    I can't thank them enough.
    My only gripe is that I couldn't speak to a technician to find out what the problem was, how they resolved it or what causes these issues for future reference. Understanding why these problems occur often helps to build your own framework of understanding. Most of the threads i've read about trackpad issues are largely unresolved with people only speculating the problem/solution.
    The initial issue I had with the trackpad's erratic behaviour seemed to be a well known problem that many are associating with a trackpad firmware update. Unless by pure coincidence I had an immediate & major hardware fault after it, which is unlikely, my personal guess is that the two issues were related.

  • Transport Issue Please help

    Hello,
    I have got a major prolen during transport.
    I have GEMPLOYE1 Which is a time dependient master data. which has Attribute called 0COUNTRY_ID.
    I have a custome attribute Called Actual PSGroup/Grade GPAYSCGR which has a compounpunding attribute 0COUNTRY_ID
    Now when I am trying to transport PSGroup/Grade GPAYSCGR to QA that transport is failing , the log massage is
    Characteristic GEMPLOYE1: Attribute GPAYSCGR compounded to 0COUNTRY_ID has a diff. time-dpdncy
    If any one saw this issue, please help me to fix the same.
    Samit

    Hi Venu,
    We can't add authorisation objects on Individual servers.We need to add authorisations on BWD ie Dev system and transport to BWI QUA system.This is the Process we need to follow as per our rule set.
    So,As the problem mentioned above if i add some auth. objects on BWD DEV system and transport it to BWI QUA system,it is getting transported Successfully to BWI,but the auth.objects what i have added on BW DEV system is not found on BW QUA system.
    What could be the problem for that,Is that the problem with transports like TP error or is it related with some tables of auth.objects...................
    Could u please analyse the problem and tell me the solution for this..........
    Thanks Much
    Swapna.D

  • Headerrenderer issue -Please help

    Headerrenderer issue -Please help
    hi
    I have a datagrid and I am  doing a custom sorting on the grid(by getting data from DB).
    I achieve this by capturing the headerrelease event of datagrid .In thee venthandler I will query from DB and do event.preventdefault to prevent standard grid sorting.
    Now I need to display my own custom ascending/descending arrows in the header.i have created an header renderer for this,
    In the headerrenderer I am lsitening to the headerrelease event of datagrid and in the eventlistener, as per the sortfield, i am trying to make the sort arrow visible/invisible.
    But somehow making the sort arrows visible/invisible is not working.The initial arrow works fine.it is shown the correct column(Name) as done in the init() method.
    The eventhandler is invoked on clicking the column headers and all the alerts are shown.
    Please see the headerrenderer code below and help me.(code is not complete only the relevant part is included)
    <?xml version="1.0" encoding="utf-8"?><mx:HBox   
    xmlns:mx="http://www.adobe.com/2006/mxml" width="100%" height="100%" horizontalScrollPolicy="off" creationComplete="init()" implements="mx.controls.listClasses.IDropInListItemRenderer">  
    public function init():void{
     headerLabel = dataField.label; 
    _dataGrid.addEventListener(DataGridEvent.HEADER_RELEASE,sortChanged,false);  
    if(_dataField.localeCompare('Name')==0)asc.visible=true; } 
    private function sortChanged(e:DataGridEvent){
     var dg:DataGrid=e.currentTarget asDataGrid;
    varcolumn:DataGridColumn = DataGridColumn(e.currentTarget.columns[e.columnIndex]);if(_dataField.localeCompare(e.dataField)==0)
    if(asc.visible ||(!asc.visible&&!desc.visible))
    Alert.show( 
    'in..');
    asc.visible=false;
    desc.visible=true;
    else if(desc.visible){
    asc.visible= true;
    desc.visible=
    false;
    else{
    asc.visible= 
    false;
    desc.visible=
    false;
    ]]>
    </mx:Script>
    <mx:Text text="{_headerLabel}" />
    <mx:Image source="{ascIcon}" id='asc' visible="false">
    <mx:Image source="{descIcon}" id='desc' visible="false"/>
    </mx:HBox>

    I got the solution!!
    i need to assign the headerrendereer to the columns dynamically inorder for this to work:
    if anybody wants to know details of solution let  me know

  • Router/Connectivity issues please help!

    Hello, I'm running Verizon FiOS with the Westell 9100EM Modem/Wireless Router. I just recently upgraded the security settings on this (Upped to WPA2-Personal from WEP, Turned on MAC filtering, and turned off SSID Broadcast). I input all of the wireless devices in my home network (2 laptops, 3 gaming consoles, 1 netbook, 1 desktop w/ wireless card, and 1 wireless printer) into the allowed devices list, and confirmed all of them were able to connect to the home network after turning off the SSID Broadcasting.
    The next morning I awoke to find that nothing could connect wirelessly, so I troubleshot that by just connecting again to the network by entering in the SSID when prompted, and entering in the security key. Went to work and came home to find that once again nothing was connecting wirelessly, and that I was getting "Low connectivity" warnings, and I could not connect to any internet service (browsers, IM programs, Windows Sidebar gadgets, etc.).  In the midst of trying to figure out what was going on, we had a power flicker (gotta love Florida) which reset the modem and things came back on like normal.
    Last night, I come home from work and what do ya' know... it's the same "Low Connectivity" error and symptoms as I just described, I try resetting the modem... nothing. I try resetting the modem and restarting the computer... nothing. Opened a command prompt and ran ipconfig /all and it pulled up an IP Address of 254.204.X.X (the x's are only there because I don't remember the last two octets), and so I checked the properties of the networking device on my computer to see if somehow a static IP had been set up, but it was all still set up to auto-assign everything. So, I started opening up the actual network properties and checked some boxes, changed a setting here and there, but stupidly didn't make any notes about what changes I made, and then the next thing I know the internet just came to life.
    Tonight, once again, I come home from work and school, and the network is pulling the same thing, only this time, I was able to reset the modem/router and it seemed to fix the issue.
    My question is this: Did I mess something up when I turned off SSID Broadcast, turned on WPA2-Personal, and set up MAC filtering? Or is there something wrong with the unit? Or is there something else going on here altogether?
    If anyone could please help me with this, it would really be nice to get my mom off my back. Thanks!

    You don't say what version of windows. I suggest you enable the SSID broadcast and see if that helps. If you are running WPA 2 with AES you are secure enough. The MAC filtering is adding extra overhead that is not necessary. I suggest you get rid of that. Anyone can just as easily spoof the MAC address and anyone can find the SSID if hidden. These are not security measures. WPA2 with AES is.

  • Perplexing connectivity issue Please help

    Hello,
    I am a frequent user of skype and last week itself, on thurs and friday i had two international sessions of two hours that were uninterrupted. Today, i tried the same on skype and it kept disconnecting and dropping. I thought it was a skype issue, and I tried google hangouts and same errors on both sides. Both of our internet connections are stable and working. He is utilizing skype from his mobile phone because we are utilizing teamviewer for remote desktop viewings... Someone please help me with this issue of connectivity. I performed all necessary updates for my yosemite (mac) and also reset my router and internet. went to speedtest.net am at 65mbps and 4mbps respectively..... I dont know what is going on its quite frustrating. 
    There are no firewalls being implemented btw....

    hello please help 

  • Wireless not working , please help .

    well ive been having this problem for a while with my linksysE2000 for a while . it wont let my ps3 connected wireless and when it does it stays for a while then it disconnnect after 1 hours . sometimes my wife is strong and stay for a whole day and then othere sdays my wifi doesnt even want to work please help what should i do ?

    So the main concern is only with the wireless connection? You might need to adjust some wireless settings in the router.
    Please check this link to see if this will help:
    List of common issues with Linksys wireless-N routers

  • 2 x Issues Please Help!!

    I have a 32 GB iPod Touch & have a couple of issues.
    1) Cannot seem to connect to wifi at home or the office. keep getting unable to connect error message.
    2) The main issue I am having is that my songs wont download onto the device from the library. The podcasts are going on ok but the songs arent. Initially thought it was songs I had saved to hard drive but problem still occurs with purchased tunes. I have been through the 5 r's online, re-installed the iTunes & reset all settings on device & am still having the problem. Please help cos at the moment all I have is an expensive paperweight

    Hey… I've just realised that LinkSys don't seems to make ADSL modems. Anyway, I use a 3Com OfficeConnect ADSL Wireless 11g Firewall Router which wasn't at all expensive and has worked extremely reliably for me.

  • Linksys WRT160N Online Downloading issues Please help!!

    Ok guys im a newbie to this Networking way of life.
    Your help is greatly needed and appreciated here is my problem.
    Equipment= Comcast motorola modem/Linksys WRT160N Wireless router/Linksys WGA600N wireless gaming adapter
    The issue here is i do alot of online gaming through my Xbox 360 console i can host a variety of matches online and for hours and hours at a time no lag what so ever but as you know on the Xbox360 dashboard they incorporate a wide range of downloaded content whether it be for your game library or media when I click on content to download no matter the size of the file the speed is terrible it takes about 5-10mins to get from 1% to 3% and just sits there for even a longer period of time as it is at this rate I will have to wait anywhere from 1-2hrs to download a demo or a video or netflix movie. I've contacted tech supp on this and trouble shooted different scenarios I have also port forwarded the ports and I'm still having this issue. 
    The Wireless router is located 15feet away from the gaming adapter FYI 
    Please advise!!!!   

    This may be a little old, but I have a WGA600N and a WRT610N..  I've had much the same problems but here is what I've discovered that may help.
    The WGA600N in the initial setup connected to your computer doesnt have a means of specifying exactly how you want to connect to your wireless (no channel, band, etc).  What ends up happening is that you set your wireless on your router to be "mixed" and the adapter will constantly switch channels.
    I went so far as to specify on my 5ghz band on the router that it be "N-Only" and the adapter still gave sluggish performance.
    On a whim, after reading some advice I re-setup my adapter and gave it a static IP address outside of the range of my DHCP settings.  This still gave me no better performance.
    Then, I decided to try hitting the static IP of the adapter in my browser, and voila!  I can access all the advanced settings of the adapter that you couldn't during the initial setup connected to the computer.  My adapter is using the 1.00 release and I'm able to finally tell the adapter to use "N-Only" as it defaults to "Mixed" mode and will channel surf on you dropping connections.
    Having played with both my WGA600N and WRT610N, I can hope for a better firmware release soon but hopefully these tips help you set up your adapter and router a bit better.
    Good luck!
    - Rob

  • Can I Use My Time Capsule as a 2nd Wireless Router? Pls Help

    Thanks for trying to help. I have a Time Capsule that I'm currently using to back up my files. My next door neighbor is willing to share his internet with me for half the monthly cost. He already has a wireless router and I can connect to it (no probs) except the signal strength is not so powerful since I'm a couple feet far from his router. I was wondering if I can use my Time Capsule to hook up the internet via WIFI through his wireless router (that way I have a stronger signal strength from my Time Capsule). Basically using my Time capsule as a 2nd wireless router.
    Neighbour's wireless Router = Time Capsule = My Macbook
    If I can please tell me how to set this up in details please. thanks for your time.
    Message was edited by: Thomas Pink

    You are trying to set up the Time Capsule as a Wireless Router
    and Repeater? - To share an existing wireless network, wireless?
    The AirPort Extreme was capable of repeating (like a transceiver)
    to and from an existing wireless network, to expand upon it; but
    only did this with another AirPort product, such as an Express.
    The Time Capsule and many of its features are outlined here, with more
    information: AirPort + Time Capsule: http://www.apple.com/support/airport/
    You may have to direct your question regarding expanding an existing
    wireless network, to the Discussions section for the specific products.
    Usually, the "extend a network" wireless feature in the software setup
    only applies to the use of a second Apple AirPort-type base station;
    such as the Extreme, Express, etc. The compatibility is between the
    AirPort-like Apple products; but a bridge could be made if an Express
    were attached to the other wireless network via Ethernet cable, then
    the Time Capsule may be able to see it. This would require testing.
    Apple - Support - Discussions - AirPort (+ Time Capsule)
    http://discussions.apple.com/category.jspa?categoryID=140
    Good luck & happy computing!

  • MBP running at a snail's pace, and a myriad of other interrelated issues, please help :'-(

    Hello, my MBP is running very slowly, MS Office for Mac constantly freezing, Safari constantly freezing, various little issues are arising with many different functions/programs when I try to use them; i.e., the enter key will just stop working in Excel or my Adobe Acrobat will shut itself down out of nowhere, Finder freezes and/or won't relaunch; these are just a few examples, but the overall theme is that I am experiencing problems in usability and functionality with my MBP across the board. There is no rhyme or reason to any of it, and all programs and apps seem to be affected. I first began noticing the problems upon installation of the Yosemite upgrade so initially thought that was the issue, but I have since found that malware items have added themselves to my Safari extensions. I found instructions to remove them entirely, but could not find them anywhere on my computer other than the Safari extensions when I followed the steps provided. I tried clicking "uninstall", but had no luck, which is not surprising since I am pretty sure the "uninstall" option listed with the extension is just part of the malware. I have "disabled" the extensions, but that didn't do anything. I'm sure that they have implanted themselves elsewhere and are lurking in the shadows of my operating system and wreaking havoc throughout my computer.
    The whole situation is making it extremely difficult to get anything done, and if I don't fix it soon it is going to be the major contributing factor to my complete mental collapse.
    PLEASE HELP!!!
    I tried to find suggestions in other areas of the Apple Support Community, and found the EtreCheck tool in one of the discussion threads. I ran the report on my system, and it looks like my MPB is riddled with problems. I don't even know where to begin in order to correct them. I am not sure if the malware has just taken over and is behind all of these, or if I am dealing with several different sources of trouble.
    Any help with this would be much appreciated, the EtreCheck report is as follows:
    Problem description:
    MBP usability decreased significantly after installing Yosemite. Computer constantly freezing and completing any task in any program/using any function of MBP takes 5-10x as long as it used to.
    EtreCheck version: 2.1.8 (121)
    Report generated February 8, 2015 at 7:53:07 AM EST
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Click for support] links for help with non-Apple products.
    Click the [Click for details] links for more information about that line.
    Hardware Information: ℹ️
        MacBook Pro (13-inch, Late 2011) (Technical Specifications)
        MacBook Pro - model: MacBookPro8,1
        1 2.4 GHz Intel Core i5 CPU: 2-core
        4 GB RAM Upgradeable
            BANK 0/DIMM0
                2 GB DDR3 1333 MHz ok
            BANK 1/DIMM0
                2 GB DDR3 1333 MHz ok
        Bluetooth: Old - Handoff/Airdrop2 not supported
        Wireless:  en1: 802.11 a/b/g/n
        Battery Health: Normal - Cycle count 364
    Video Information: ℹ️
        Intel HD Graphics 3000 - VRAM: 384 MB
            Color LCD 1280 x 800
    System Software: ℹ️
        OS X 10.10.1 (14B25) - Time since boot: 4 days 17:53:1
    Disk Information: ℹ️
        ST9500325ASG disk0 : (500.11 GB)
            EFI (disk0s1) <not mounted> : 210 MB
            Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
            Macintosh HD (disk1) / : 498.88 GB (332.61 GB free)
                Encrypted AES-XTS Unlocked
                Core Storage: disk0s2 499.25 GB Online
        MATSHITADVD-R   UJ-8A8 
    USB Information: ℹ️
        Apple Inc. FaceTime HD Camera (Built-in)
        Apple Inc. BRCM2070 Hub
            Apple Inc. Bluetooth USB Host Controller
        Apple Inc. Apple Internal Keyboard / Trackpad
        Apple Computer, Inc. IR Receiver
    Thunderbolt Information: ℹ️
        Apple Inc. thunderbolt_bus
    Gatekeeper: ℹ️
        Mac App Store and identified developers
    Kernel Extensions: ℹ️
            /Applications/Kies.app
        [not loaded]    com.devguru.driver.SamsungACMControl (1.4.26 - SDK 10.6) [Click for support]
        [not loaded]    com.devguru.driver.SamsungACMData (1.4.26 - SDK 10.6) [Click for support]
        [not loaded]    com.devguru.driver.SamsungComposite (1.4.26 - SDK 10.6) [Click for support]
        [not loaded]    com.devguru.driver.SamsungMTP (1.4.26 - SDK 10.5) [Click for support]
        [not loaded]    com.devguru.driver.SamsungSerial (1.4.26 - SDK 10.6) [Click for support]
            /Library/Extensions
        [loaded]    com.sophos.kext.sav (9.2.50 - SDK 10.8) [Click for support]
        [loaded]    com.sophos.nke.swi (9.2.50 - SDK 10.8) [Click for support]
    Problem System Launch Agents: ℹ️
        [killed]    com.apple.CallHistoryPluginHelper.plist
        [killed]    com.apple.CallHistorySyncHelper.plist
        [killed]    com.apple.cmfsyncagent.plist
        [killed]    com.apple.coreservices.appleid.authentication.plist
        [killed]    com.apple.EscrowSecurityAlert.plist
        [killed]    com.apple.Maps.pushdaemon.plist
        [killed]    com.apple.rcd.plist
        [killed]    com.apple.recentsd.plist
        [killed]    com.apple.SafariNotificationAgent.plist
        9 processes killed due to memory pressure
    Problem System Launch Daemons: ℹ️
        [killed]    com.apple.AssetCacheLocatorService.plist
        [killed]    com.apple.awdd.plist
        [killed]    com.apple.coresymbolicationd.plist
        [killed]    com.apple.ctkd.plist
        [killed]    com.apple.emond.aslmanager.plist
        [killed]    com.apple.GSSCred.plist
        [killed]    com.apple.ifdreader.plist
        [killed]    com.apple.installd.plist
        [killed]    com.apple.nehelper.plist
        [killed]    com.apple.periodic-monthly.plist
        [killed]    com.apple.periodic-weekly.plist
        [killed]    com.apple.sandboxd.plist
        [killed]    com.apple.softwareupdate_download_service.plist
        [killed]    com.apple.tccd.system.plist
        [killed]    com.apple.wdhelper.plist
        15 processes killed due to memory pressure
    Launch Agents: ℹ️
        [not loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
        [running]    com.adobe.AdobeCreativeCloud.plist [Click for support]
        [running]    com.canon.MFManager.plist [Click for support]
        [unknown]    com.oracle.java.Java-Updater.plist [Click for support]
        [running]    com.sophos.uiserver.plist [Click for support]
    Launch Daemons: ℹ️
        [loaded]    com.adobe.fpsaud.plist [Click for support]
        [loaded]    com.microsoft.office.licensing.helper.plist [Click for support]
        [unknown]    com.oracle.java.Helper-Tool.plist [Click for support]
        [running]    com.sophos.common.servicemanager.plist [Click for support]
    User Launch Agents: ℹ️
        [loaded]    com.adobe.AAM.Updater-1.0.plist [Click for support]
        [loaded]    com.adobe.ARM.[...].plist [Click for support]
        [loaded]    com.divx.agent.postinstall.plist [Click for support]
        [loaded]    com.kodak.KODAK AiO Firmware Updater.plist [Click for support]
        [loaded]    com.kodak.KODAK AiO Software Updater.plist [Click for support]
        [running]    com.kodak.StatisticCollection.plist [Click for support]
    User Login Items: ℹ️
        iTunesHelper    Application Hidden (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
        Dropbox    UNKNOWN  (missing value)
        bomgar-scc-20140103-113305    UNKNOWN  (missing value)
        KiesAgent    Application Hidden (/Applications/Kies.app/Contents/MacOS/KiesAgent.app)
        fuspredownloader    Application Hidden (/Users/[redacted]/Library/Application Support/.FUS/fuspredownloader.app)
    Internet Plug-ins: ℹ️
        AmazonMP3DownloaderPlugin1017277: Version: AmazonMP3DownloaderPlugin 1.0.17 [Click for support]
        OVSHelper: Version: 1.1 [Click for support]
        Default Browser: Version: 600 - SDK 10.10
        AdobeExManDetect: Version: AdobeExManDetect 1.1.0.0 - SDK 10.7 [Click for support]
        AdobeAAMDetect: Version: AdobeAAMDetect 2.0.0.0 - SDK 10.7 [Click for support]
        AdobePDFViewerNPAPI: Version: 11.0.10 - SDK 10.6 [Click for support]
        DivXBrowserPlugin: Version: 2.2 [Click for support]
        FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
        Flash Player: Version: 16.0.0.305 - SDK 10.6 [Click for support]
        QuickTime Plugin: Version: 7.7.3
        Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Click for support]
        SharePointBrowserPlugin: Version: 14.4.7 - SDK 10.6 [Click for support]
        AdobePDFViewer: Version: 11.0.10 - SDK 10.6 [Click for support]
        CANONiMAGEGATEWAYDL: Version: 3.2.0.1 - SDK 10.6 [Click for support]
    User internet Plug-ins: ℹ️
        WebEx64: Version: 1.0 - SDK 10.5 [Click for support]
        Google Earth Web Plug-in: Version: 7.1 [Click for support]
    Safari Extensions: ℹ️
        Saveonmac
        iMedia Converter Deluxe 
        MacVeXe
        DivX Plus Web Player HTML5 <video>
    3rd Party Preference Panes: ℹ️
        DivX  [Click for support]
        Flash Player  [Click for support]
    Time Machine: ℹ️
        Time Machine not configured!
    Top Processes by CPU: ℹ️
            16%    WindowServer
            11%    SophosAutoUpdate
             8%    com.apple.WebKit.Plugin.64
             8%    Safari
             2%    SophosUIServer
    Top Processes by Memory: ℹ️
        120 MB    Safari
        116 MB    SophosWebIntelligence
        43 MB    SophosScanD
        43 MB    InterCheck
        39 MB    WindowServer
    Virtual Memory Information: ℹ️
        44 MB    Free RAM
        751 MB    Active RAM
        724 MB    Inactive RAM
        1.21 GB    Wired RAM
        60.34 GB    Page-ins
        819 MB    Page-outs

    The minimum requirement is 2GB, but most people think 4GB is the bare minimum.
    I primarily buy from Crucial, Other World Computing, or MemoryTen. As long as they have a "configurator" where you pick you exact Mac from a list and it lists all the compatible memory for that Mac, AND it has a lifetime warranty on the RAM, it should be ok.  Macs are very picky about the RAM because they use it to its full capacity. If there are any faults in the modules, it will crash.
    There are suggestions for sites in other parts of the world on the EveryMac website. Look down in the Section for RAM where you'll find links to their sponsors (OWC is the US-based one).
    In Apple's world, there is a difference between and "Upgrade" and an "Update." Updates should generally be installed as they patch vulnerabilities and fix bugs.
    Upgrades on the other hand are an entirely new Operating System (OS). A change in the OS can cause many problems with your installed software as it may not be compatible with the changes. It may rely on programming interfaces that have been removed. They should know that they will be removed as Apple publishes those facts many years prior to removing the features.
    An Upgrade takes you to a major, new version of software whereas and Update just makes changes to the same major version of the software.
    Yosemite was an Upgrade, not an Update.

  • Connecting to a wireless print server, please help!!!

    i have a canon mp500 connected to a network through a wireless printserver and wireless router. the printer works when directly connected to my macbook, but not when connected to the print server. i contacted linksys and they sent a docment on how to set the printer up using it's ip address. still didn't work (the instructions were for 10.1 and 10.2). i have downloaded and installed the current mac os x drivers from the canon website with no luck. please help

    I'm no expert, but I was able setup HP printer connected wirelessly to AEBS by using Apple's Printer Setup Utility and Bonjour. I was, however, able to install the HP drivers using the software that came with the printer, but it sounds like you could not do so with Canon?
    Anyway, here are Apple's help files for adding an IP printer:
    "Connecting to an IP printer
    An IP printer is a network printer that uses TCP/IP protocols (such as LPD/LPR, IPP, or Socket or Jet Direct) to communicate with your computer. If the IP printer you want to use is not listed when you print, you can add it to your list of available printers.
    To add an IP printer, you need to know its IP address or DNS name. See your network administrator for assistance.
    Open the document to print, and choose File > Print.
    Choose Add Printer from the Printer pop-up menu, and click IP Printer in the dialog that appears.
    Choose the appropriate printing protocol from the Protocol pop-up menu.
    Type the IP address or DNS name for the printer in the Address field.
    If your printer requires it, type the queue name for your printer in the Queue Name field. If you don't know the queue name, see your network administrator for assistance.
    Enter a name and location for the printer, so you can identify it in the Printer pop-up menu.
    If the Print Using pop-up menu does not display the name of your printer's model, choose the item appropriate for your printer from the Print Using pop-up menu, and then select your printer in the Model Name list.
    Click Add.
    Usually, your computer can detect whether a printer has special accessories installed, such as additional paper trays, extra memory, or a duplex unit. If it can't, a dialog appears that lets you specify them. Make sure the settings in that dialog accurately reflect your printer's installed accessories so you can take full advantage of them."

Maybe you are looking for