Personal Domain not function after Move the Domain (iWeb) to a New Mac

Hey,
I recently move my iWeb Domain to a new Macbook Pro..after Published the iWeb...the message window shown visit the website as web.me.com/xxx instead www.xxx.com
Why?
i try to reset the personal domain in MobileMe ,remove it and add it again...now re-published...the same result...and when click on Visit...the URL shown web.me.com/xxx instead www.xxx.com
Any problem here?help me please...thanks

All right now...
I Delete the iWeb.plist (UserID-Library-Preferences-com.apple.iweb.plist) and re-publish it again...Now...huh...No Problem at all...
cheers

Similar Messages

ASA5505 L2L VPN does not function after move and reconfiguration

                   I have an ASA5505 that had multiple VPNs to both Cisco5505's and other Vendor security appliances. The one in question that moved to a new IP address checks out on isa sa, ipsec sa and nat, yet there is no communication accross the tunnel. This behavior is consistent accross all remote sites. The remote sites function normally. Below is the output with some show commands.
ASA Version 8.4(4)
hostname RitterBars
names
name 67.231.37.42 RitterLAB-ASA
name 67.231.37.45 RitterLAB-LB-WAN1
name 64.233.131.94 RitterLAB-LB-WAN3
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 3
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
description Port 7 on 9108
nameif outside
security-level 0
ip address dhcp setroute
interface Vlan3
no forward interface Vlan2
nameif CoreNetwork
security-level 0
ip address 172.20.10.22 255.255.255.128
boot system disk0:/asa844-k8.bin
ftp mode passive
clock timezone CST -6
clock summer-time CST recurring
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.9.0
subnet 192.168.9.0 255.255.255.0
object network obj-192.168.85.0
subnet 192.168.85.0 255.255.255.0
object network obj-10.200.1.0
subnet 10.200.1.0 255.255.255.0
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.1.2
host 192.168.1.2
object service obj-tcp-source-eq-22
service tcp source eq ssh
object service obj-tcp-source-eq-5922
service tcp source eq 5922
object network obj-192.168.1.10
host 192.168.1.10
object service obj-tcp-source-eq-5125
service tcp source eq 5125
object service obj-tcp-source-eq-80
service tcp source eq www
object network obj-192.168.1.119
host 192.168.1.119
object service obj-udp-source-eq-69
service udp source eq tftp
object network obj-192.168.1.51
host 192.168.1.51
object service obj-tcp-source-eq-443
service tcp source eq https
object service obj-tcp-source-eq-5980
service tcp source eq 5980
object network obj-192.168.1.114
host 192.168.1.114
object network obj-96.43.39.27
host 96.43.39.27
object network obj-xxx.xxx.xxx.xxx
host xxx.xxx.xxx.xxx
object-group network Inside
network-object 192.168.1.0 255.255.255.0
access-list split-tunnel extended permit ip 192.168.1.0 255.255.255.0 192.168.9.0 255.255.255.0
access-list no_nat extended permit ip 192.168.1.0 255.255.255.0 192.168.9.0 255.255.255.0
access-list no_nat extended permit ip 192.168.1.0 255.255.255.0 192.168.85.0 255.255.255.0
access-list no_nat extended permit ip 192.168.1.0 255.255.255.0 10.200.1.0 255.255.255.0
access-list no_nat extended permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
access-list VPN2LAB extended permit ip 192.168.1.0 255.255.255.0 192.168.85.0 255.255.255.0
access-list VPN2LAB extended permit ip 192.168.1.0 255.255.255.0 10.200.1.0 255.255.255.0
access-list Barracudalab extended permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
access-list inat extended permit ip 192.168.1.0 255.255.255.0 any
access-list vnat extended permit ip 192.168.1.0 255.255.255.0 host 216.163.29.244
access-list out2in extended permit tcp host 64.233.128.6 host 192.168.1.2 eq ssh
access-list out2in extended permit tcp 64.233.128.0 255.255.255.0 host 192.168.1.2 eq ssh
access-list out2in extended permit tcp 64.233.128.0 255.255.255.0 host 192.168.1.10 eq 5125
access-list out2in extended permit tcp 64.233.128.0 255.255.255.0 host 192.168.1.10 eq www
access-list out2in extended permit udp 64.233.128.0 255.255.255.0 host 192.168.1.119 eq tftp
access-list out2in extended permit tcp 64.233.128.0 255.255.255.0 host 192.168.1.51 eq https
access-list out2in extended permit ip 64.233.128.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list out2in extended permit tcp any host 192.168.1.10 eq 5125
access-list out2in extended permit tcp any host 192.168.1.10 eq www
access-list out2in extended permit tcp any 192.168.1.0 255.255.255.0 eq ftp
access-list out2in extended permit tcp any 192.168.1.0 255.255.255.0 eq ftp-data
access-list out2in extended permit udp any host 192.168.1.119 eq tftp
access-list out2in extended permit tcp any host 192.168.1.51 eq https
access-list out2in extended permit icmp any any
pager lines 24
logging console alerts
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu CoreNetwork 1500
ip local pool vpn-pool 192.168.9.10-192.168.9.250
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static obj-192.168.1.0 obj-192.168.1.0 destination static obj-192.168.9.0 obj-192.168.9.0 no-proxy-arp
nat (inside,any) source static obj-192.168.1.0 obj-192.168.1.0 destination static obj-192.168.85.0 obj-192.168.85.0 no-proxy-arp
nat (inside,any) source static obj-192.168.1.0 obj-192.168.1.0 destination static obj-10.200.1.0 obj-10.200.1.0 no-proxy-arp
nat (inside,any) source static obj-192.168.1.0 obj-192.168.1.0 destination static obj-192.168.3.0 obj-192.168.3.0 no-proxy-arp
nat (inside,outside) source static obj-192.168.1.2 interface service obj-tcp-source-eq-22 obj-tcp-source-eq-5922
nat (inside,outside) source static obj-192.168.1.10 interface service obj-tcp-source-eq-5125 obj-tcp-source-eq-5125
nat (inside,outside) source static obj-192.168.1.10 interface service obj-tcp-source-eq-80 obj-tcp-source-eq-80
nat (inside,outside) source static obj-192.168.1.119 interface service obj-udp-source-eq-69 obj-udp-source-eq-69
nat (inside,outside) source static obj-192.168.1.51 interface service obj-tcp-source-eq-443 obj-tcp-source-eq-5980
nat (inside,outside) source static obj-192.168.1.114 obj-96.43.39.27
nat (inside,CoreNetwork) source dynamic obj-192.168.1.0 interface destination static obj-xxx.xxx.xxx.xxx obj-xxx.xxx.xxx.xxx
nat (inside,outside) source dynamic Inside interface
nat (inside,outside) after-auto source dynamic any interface
access-group out2in in interface outside
route CoreNetwork 172.20.30.0 255.255.255.248 172.20.10.1 1
route CoreNetwork 216.163.29.244 255.255.255.255 172.20.10.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 0:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set psset esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto map samap 1 match address VPN2LAB
crypto map samap 1 set peer RitterLAB-ASA
crypto map samap 1 set ikev1 transform-set ESP-AES-256-SHA
crypto map samap 2 match address Barracudalab
crypto map samap 2 set peer RitterLAB-LB-WAN1 RitterLAB-LB-WAN3
crypto map samap 2 set ikev1 transform-set ESP-3DES-SHA
crypto map samap interface outside
crypto isakmp identity address
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 11
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access inside
dhcpd dns 64.233.128.10 64.233.128.11
dhcpd auto_config outside
dhcpd address 192.168.1.100-192.168.1.150 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 66.187.233.4 source outside
ntp server 64.99.80.30 source outside
webvpn
username xxx.xxx.xxx.xxx password xxx.xxx.xxx.xxx encrypted privilege 15
username xxx.xxx.xxx.xxx attributes
vpn-group-policy WebVPNpolicy
username xxx.xxx.xxx.xxx password xxx.xxx.xxx.xxx encrypted privilege 15
username xxx.xxx.xxx.xxx attributes
vpn-group-policy WebVPNpolicy
tunnel-group 67.231.37.42 type ipsec-l2l
tunnel-group 67.231.37.42 ipsec-attributes
ikev1 pre-shared-key xxx.xxx.xxx.xxx
tunnel-group 67.231.37.45 type ipsec-l2l
tunnel-group 67.231.37.45 ipsec-attributes
ikev1 pre-shared-key xxx.xxx.xxx.xxx
tunnel-group 64.233.131.94 type ipsec-l2l
tunnel-group 64.233.131.94 ipsec-attributes
ikev1 pre-shared-key xxx.xxx.xxx.xxx
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect ip-options
inspect tftp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:bcdf7281cbf323ff6af7457149529a5b
: end
RitterBars# sh isa sa
IKEv1 SAs:
   Active SA: 2
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2
1   IKE Peer: 67.231.37.45
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
2   IKE Peer: 67.231.37.42
    Type    : L2L             Role    : initiator
    Rekey   : no              State   : MM_ACTIVE
There are no IKEv2 SAs
RitterBars# sh ipsec sa
interface: outside
    Crypto map tag: samap, seq num: 1, local addr: 96.43.41.168
      access-list VPN2LAB extended permit ip 192.168.1.0 255.255.255.0 192.168.85.0 255.255.255.0
      local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.85.0/255.255.255.0/0/0)
      current_peer: 67.231.37.42
      #pkts encaps: 4, #pkts encrypt: 4, #pkts digest: 4
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 4, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 96.43.41.168/0, remote crypto endpt.: 67.231.37.42/0
      path mtu 1500, ipsec overhead 74, media mtu 1500
      current outbound spi: 6F98A015
      current inbound spi : 6DD466F0
    inbound esp sas:
      spi: 0x6DD466F0 (1842636528)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 1122304, crypto-map: samap
         sa timing: remaining key lifetime (kB/sec): (4374000/28182)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    outbound esp sas:
      spi: 0x6F98A015 (1872273429)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 1122304, crypto-map: samap
         sa timing: remaining key lifetime (kB/sec): (4373999/28182)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    Crypto map tag: samap, seq num: 2, local addr: 96.43.41.168
      access-list Barracudalab extended permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
      local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.3.0/255.255.255.0/0/0)
      current_peer: 67.231.37.45
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 96.43.41.168/0, remote crypto endpt.: 67.231.37.45/0
      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 51AF17EA
      current inbound spi : 859BC586
    inbound esp sas:
      spi: 0x859BC586 (2241578374)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 1118208, crypto-map: samap
         sa timing: remaining key lifetime (sec): 28152
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    outbound esp sas:
      spi: 0x51AF17EA (1370429418)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, }
         slot: 0, conn_id: 1118208, crypto-map: samap
         sa timing: remaining key lifetime (sec): 28152
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
RitterBars# sh nat int inside
Manual NAT Policies (Section 1)
1 (inside) to (any) source static obj-192.168.1.0 obj-192.168.1.0   destination static obj-192.168.9.0 obj-192.168.9.0 no-proxy-arp
    translate_hits = 0, untranslate_hits = 0
2 (inside) to (any) source static obj-192.168.1.0 obj-192.168.1.0   destination static obj-192.168.85.0 obj-192.168.85.0 no-proxy-arp
    translate_hits = 18, untranslate_hits = 0
3 (inside) to (any) source static obj-192.168.1.0 obj-192.168.1.0   destination static obj-10.200.1.0 obj-10.200.1.0 no-proxy-arp
    translate_hits = 0, untranslate_hits = 0
4 (inside) to (any) source static obj-192.168.1.0 obj-192.168.1.0   destination static obj-192.168.3.0 obj-192.168.3.0 no-proxy-arp
    translate_hits = 0, untranslate_hits = 0
5 (inside) to (outside) source static obj-192.168.1.2 interface   service obj-tcp-source-eq-22 obj-tcp-source-eq-5922
    translate_hits = 0, untranslate_hits = 0
6 (inside) to (outside) source static obj-192.168.1.10 interface   service obj-tcp-source-eq-5125 obj-tcp-source-eq-5125
    translate_hits = 0, untranslate_hits = 9094
7 (inside) to (outside) source static obj-192.168.1.10 interface   service obj-tcp-source-eq-80 obj-tcp-source-eq-80
    translate_hits = 0, untranslate_hits = 126
8 (inside) to (outside) source static obj-192.168.1.119 interface   service obj-udp-source-eq-69 obj-udp-source-eq-69
    translate_hits = 0, untranslate_hits = 0
9 (inside) to (outside) source static obj-192.168.1.51 interface   service obj-tcp-source-eq-443 obj-tcp-source-eq-5980
    translate_hits = 0, untranslate_hits = 195
10 (inside) to (outside) source static obj-192.168.1.114 obj-96.43.39.27
    translate_hits = 0, untranslate_hits = 0
11 (inside) to (CoreNetwork) source dynamic obj-192.168.1.0 interface   destination static obj-216.163.29.244 obj-216.163.29.244
    translate_hits = 107, untranslate_hits = 0
12 (inside) to (outside) source dynamic Inside interface
    translate_hits = 35387, untranslate_hits = 2940
Manual NAT Policies (Section 3)
1 (inside) to (outside) source dynamic any interface
    translate_hits = 291, untranslate_hits = 78

I just recently got the triple play package from verizon with fios too. And of course the Actiontec is total crap. The very first night it rebooted over and over again. What good is an internet connection you can't use right... Anyways, I have a cisco 831 that i use for a VPN to work, and so, I decided to put that up front.
Anyways, had the same problem. First I setup my router to bridge the connetion from the Actiontec to my router. So it goes Broadband Moca -> Actiontec LAN -(eth cable)-> Cisco WAN port. This worked great, except now my vod didn't work. So then I found this article....
http://www.dslreports.com/forum/r19559467-How-To-MI424WR-Network-Bridge-working-FIOS-TV
It was genius, add a second bridge from the Cisco LAN -(eth cable)-> Actiontec WAN -> local Moca.    And then put DHCP relay on the bridge. Everything worked again, hooray. then I added an access list, and there went my vod again.
So then I spent about two hours turning ports on and off and such, finally I figured it out. You'll need to allow inbound established tcp connections that internal hosts create. This will get back your guide and allow the vod menu to work again. then you have to allow inbound connections on udp port 21310. I applied it and lo and behold vod is back. Now my only problem is that the 831 only has a 10 Mb/s ethernet WAN, so I can't get HD VOD but ah well. I'll upgrade one of these days to an 851 or 871.
Here's what the access lists should look like in IOS:
permit tcp any host (your external IP address) established
permit udp any host (your external IP address) eq 21310
probably is going to be a little bit different since you have an ASA but I think you get the idea.

COM object model not functioning after encrypting the word document using office extention

     After encrypting A word document using office extention, it seems like the COM object model becomes unusable. I cannot not manipulate the encrypt document through COM interface, nor can I write macro VBScript to do some operation on the docuent.
     For example, I create a word Macro with some simple code.
Sub hi()
    Dim i As Integer
    i = ThisDocument.Fields.Count
    MsgBox i
End Sub
     If the document is not encrypt, then we will see a msgbox which tells us the number of bookmarks in the current document.
     Now, encrypt the word document using the office extention, running the macro code will fail with error code " 80004005" and error message:Method 'Fields' of bject 'ThisDocument' failed.
It is very important for us to manipulate word documents through COM interface in our system, I want to know why the COM interface does not work anymore after the document is encrypted.

I take macro script as an example to demonstrate that word COM object model cannot be used after encripted. Actually you can reproduce the same problem when you manipulate word document through COM interface using any programming language.
For example, you can create a text document with the following VBscript:
set a = createobject("Word.Application")
set doc = a.Documents.Open("E:\temp\test.docx")
msgbox doc.Fields.count
doc.close
a.quit
Save the document with ".vbs" file extention and then run it by double clicking it. it will fail if the document is encrypted using the office extention.

HT2292 Phone indicates connection to itunes on screen, will not function, after rebooting the itunes connection screen is still there.

While downloading update, itune connection screen will not go away, phone will not work even after rebooting with itunes connection screen reappearing

Your iPhone is in recoverty mode at the moment so to possibly get it back up and running you would need to do a restore as you have been trying. Follow the steps in the article below for the specific error messages you have been receiving. If after following all steps the issue remains book an appointment at a local Apple Retail Store to have the iPhone evaluated.
Resolve specific iTunes update and restore errors

Could not provision the RemoteApp collection. Error: Could not join the domain. Unable to reach the domain.

Hi
I am trying to set up an Azure RemoteApp Hybrid solution.
I have created RemoteApp net and uploaded a custom image and all that is fine.
When I link my template to my Collection it fails after provisioning for about an hour.
I recive the following message: Could not provision the RemoteApp collection. Error: Could not join the domain. Unable to reach the domain.
The join domin works fine and I have tryed with account with different lvl of access to my AD.
Any suggestion how to solve this?

Hello Eric,
I am landing into the same Problem and i read your guidance on this issue. Let me answer it point by point.
1. Check the VPN state to ensure it is active or connected state:
Sundesh:My Azure RemoteApp Virtual Network after successfull S2S configuration shows as Ready. Is that what you mean by Connected State? Earlier to S2S, it was just under connecting state.
2. Verify your VNET configurations have proper IP address ranges
Sundesh: The VNET address range, the Local address range and DNS has already been verified twice. In fact the same address ranges(with exception to VNET) are working fine on a VENT config on Azure VM instance. Verified.
3. Verify your DNS IP configurations are valid, (often this is the problem)
Sundesh: Yes its done and verified
4. Verify the credentials entered for domain join are valid.
Sundesh: Tested these credentials by joining a regular Azure VM to domain and it works there.
5. Make sure your VPN endpoint that Azure RemoteApp service is connecting to is not blocking traffic.
Sundesh: Can you please let us know the specific port numbers that we need to consider and i can have it checked with the Network team
Thanks
SUndesh

Why is the scroll function not working after accessing the voice feature in settings?

Why is the scroll function not working after accessing the voice feature in settings?

For some prerecorded audio files the Transpose slider will not work reliably. I found no clear pattern, when it does and when not.
If all fails, create a loop from the audio file. Select the region in the track and use the command "File: Add region to Loop library".
Set the current key and tempo, name the loop, and save the loop.
Now add it from the loop browser to a new track and delete your old track. The search field in the Loop browser will help you to find the loop quickly.
You will be able to transpose the sample as described above, like a regular loop.
For example - a audio file turned into a loop and transposed:

Error: A user with the specified SID could not be found in the domain.

Hi All,
I am getting a error as below,
A user with the specified SID could not be found in the domain.
Check the spelling of the account name 'domain\usersAMAccountName' and try again.
-    at Microsoft.Office.Server.UserProfiles.UserProfileGlobal.GetSidFromAccount(String strAccountName, SID_NAME_USE[] IntendedAccountType, SID_NAME_USE& sidUse)
   at Microsoft.Office.Server.UserProfiles.UserProfileGlobal.GetSidFromAccount(String strAccountName)
   at Microsoft.Office.Server.UserProfiles.UserProfileGlobal.GetSidFromAccount(UserProfileApplicationProxy proxy, Guid partitionID, String strAccountName, Boolean isWindowsAccount)
   at Microsoft.Office.Server.UserProfiles.UserProfile.set_SID()
   at Microsoft.Office.Server.UserProfiles.UserProfile..ctor(UserProfileManager objManager, String strAccountName, String strPreferredName)
   at Microsoft.Office.Server.UserProfiles.UserProfileManager.CreateUserProfile(String strAccountName, String strPreferredName)
   at Microsoft.Office.Server.UserProfiles.UserProfileManager.CreateUserProfile(String strAccountName)
Any help?
Thanks,
Mohakk

Hi,
Per my understanding, the code should be OK, I have two suggestions as below:
1. Please ensure that the account of that user is valid in your production environment;
2. Try other accounts in the CreateUserProfile() funciton to see if it can work.
Feel free to reply if there any progress.
Best regards,
Patrick
Patrick Liang
TechNet Community Support

Customer exit is not functioning after ECC upgrade/support package

It seems our customer exit is not functioning after ECC upgrade/support package. I tried to activate the project again, no use. please help. Thanks! (see below for the enhancement info)
COZF0002 Change purchase req. for externally procured component
EXIT_SAPLCOZF_002
INCLUDE ZXCOZU02
*& Include           ZXCOZU02
CONSTANTS: lcc_eban(25)   TYPE c VALUE '(SAPLCOBC)EBAN'.
FIELD-SYMBOLS: <fs_eban>   TYPE eban.
DATA: l_fkstl TYPE prps-fkstl.
Move values from the LUW to the Internal Table
ASSIGN (lcc_eban) TO <fs_eban>.
If the field symbol is "NOT' empty then proceed
IF ( <fs_eban> IS ASSIGNED ).
if WBS work order, get cost center from PRPS
IF ( caufvd_imp-auart = 'ZM05' ).
    SELECT SINGLE fkstl INTO l_fkstl FROM prps
      WHERE pspnr = caufvd_imp-pspel.
    IF ( sy-subrc = 0 ).
      WRITE l_fkstl TO <fs_eban>-zzfistl.
    ENDIF.
if not WBS WO, move cost center minus leading zeros to funds center
ELSE.
    WRITE caufvd_imp-kostl TO <fs_eban>-zzfistl.
ENDIF.
ENDIF.

Did you mean set a break point in the follow code?(Include ZXCOZU02), I tried set a break point in this code, but It didn't stop .
*& Include ZXCOZU02
CONSTANTS: lcc_eban(25) TYPE c VALUE '(SAPLCOBC)EBAN'.
FIELD-SYMBOLS: <fs_eban> TYPE eban.
DATA: l_fkstl TYPE prps-fkstl.
Move values from the LUW to the Internal Table
ASSIGN (lcc_eban) TO <fs_eban>.
If the field symbol is "NOT' empty then proceed
IF ( <fs_eban> IS ASSIGNED ).
if WBS work order, get cost center from PRPS
IF ( caufvd_imp-auart = 'ZM05' ).
SELECT SINGLE fkstl INTO l_fkstl FROM prps
WHERE pspnr = caufvd_imp-pspel.
IF ( sy-subrc = 0 ).
WRITE l_fkstl TO <fs_eban>-zzfistl.
ENDIF.
if not WBS WO, move cost center minus leading zeros to funds center
ELSE.
WRITE caufvd_imp-kostl TO <fs_eban>-zzfistl.
ENDIF.
ENDIF.

Iphone 4 personal Hotspot not working after update to IOS 7.1 India BSNL cellular

Iphone 4 personal Hotspot not working after update to IOS 7.1 India BSNL cellular

BSNL is not a supported carrier. Personal Hotspot requires carrier support and provisioning of the account to enable it. iOS 7.1 disabled the ability to manually configure Personal Hotspot on unsupported carriers.

Personal hotspot not working after upgrading to ios7

Personal hotspot not working after upgrading to ios7

I was having this problem (iphone 5 wouldn't work as hotspot for my PC laptop) and had tried everything suggested on these message boards, so I finally went to the Apple Genius Bar and they fixed it for me. Here's what they did:
1) Turned the Hotspot off on my iphone
2) Went to the Control Panel on my laptop to "Network and Internet" > "Network and Sharing Center" > "Manage Wireless Networks" (on the left navigation panel) and deleted my iphone from the list of WiFi connections I've attempted.
3) Flipped the manual WiFi switch on my laptop to Off and then back On again (to reset it)
4) Turned the Hotspot on my iphone back on
After that, when I tried to connect, it worked. Hope this works for someone else.

Firewire does not function after uninstalling macfuse and an out of date version of NTFS32 and then installed latest version of Tuxera NTFS for Mac.

I purchased a 3TB HDD (WD USB 3.0 $100) to replace the 2TB Seagate for a new Time Machine HDD. The 2B was full and backups were deleting older files. The 3TB was formatted NTFS and I want to "recover" the included SW before I reformatted the HDD for the iMac. I discovered that MacFuse was out of date and unsupported and my NTFS-32 was also out of date so I uninstalled both and then installed the most recent version of Tuxera NTFS for Mac. I rebooted and discovered that the FW800 port was unresponsive. Below is the EtreCheck report:
Problem description:
Firewire does not function after uninstalling macfuse and an out of date version of NTFS32 and then installed Tuxera NTFS for Mac.
EtreCheck version: 2.0.8 (95)
Report generated October 30, 2014 7:11:17 PM EDT
Hardware Information: ℹ️
iMac (24-inch Mid 2007) (Verified)
iMac - model: iMac7,1
1 2.8 GHz Intel Core 2 Duo CPU: 2-core
4 GB RAM
BANK 0/DIMM0
2 GB DDR2 SDRAM 667 MHz ok
BANK 1/DIMM1
2 GB DDR2 SDRAM 667 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
ATI,RadeonHD2600 - VRAM: 256 MB
iMac 1920 x 1200
System Software: ℹ️
OS X 10.8.5 (12F45) - Uptime: 0:17:34
Disk Information: ℹ️
WDC WD5000AAKS-40TMA0 disk0 : (500.11 GB)
S.M.A.R.T. Status: Verified
disk0s1 (disk0s1) <not mounted> : 210 MB
ML 10.8 (disk0s2) / [Startup]: 499.25 GB (20.92 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
USB Information: ℹ️
Apple Inc. Built-in iSight
Apple Computer, Inc. IR Receiver
Logitech USB Receiver
Apple Inc. Bluetooth USB Host Controller
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Applications/Hardware Monitor ƒ/HardwareMonitor.app
[loaded] com.bresink.driver.BRESINKx86Monitoring (7.0) Support
/Applications/Parallels Desktop.app
[not loaded] com.parallels.kext.hidhook (8.0 18615.948847) Support
[not loaded] com.parallels.kext.hypervisor (8.0 18615.948847) Support
[not loaded] com.parallels.kext.netbridge (8.0 18615.948847) Support
[not loaded] com.parallels.kext.usbconnect (8.0 18615.948847) Support
[not loaded] com.parallels.kext.vnic (8.0 18615.948847) Support
/Applications/Toast Titanium v11.1/Spin Doctor.app
[not loaded] com.hzsystems.terminus.driver (4) Support
/Applications/Toast Titanium/Toast Titanium v11.1 (1072).app
[not loaded] com.roxio.TDIXController (2.0) Support
/Library/Application Support/Symantec/AntiVirus
[loaded] com.symantec.kext.SymAPComm (12.2f1 - SDK 10.6) Support
/System/Library/Extensions
[loaded] com.Logitech.Control Center.HID Driver (3.9.0 - SDK 10.6) Support
[loaded] com.eltima.ElmediaPlayer.kext (1.58 - SDK 10.4) Support
[not loaded] com.hzsystems.driver.CDSDAudioCaptureSupport (1.5) Support
[not loaded] com.increw.kext.speedit (0.32) Support
[loaded] com.logitech.manager.kernel.driver (4.10.0 - SDK 10.8) Support
[not loaded] com.olympus.CamBlockCommandsDevice (2.0.0) Support
[not loaded] com.olympus.CamBlockCommandsDeviceUP (2.0.0) Support
[not loaded] com.palm.ClassicNotSeizeDriver (3.2.1) Support
[not loaded] com.roxio.BluRaySupport (1.1.6) Support
[not loaded] com.seagate.driver.PowSecDriverCore (5.1.1) Support
[loaded] com.symantec.kext.internetSecurity (5.2f1 - SDK 10.6) Support
[loaded] com.symantec.kext.ips (3.5f1 - SDK 10.6) Support
[loaded] com.symantec.kext.ndcengine (1.0f1 - SDK 10.6) Support
[loaded] com.taoeffect.ispy.kext (2.0.2 - SDK 10.2) Support
/System/Library/Extensions/OlympusDSCDriver.kext/Contents/PlugIns
[not loaded] com.olympus.CamFWSerialBusProtocolTransport (2.0.0) Support
[not loaded] com.olympus.CamUSBMassStorageClass (2.0.0) Support
/System/Library/Extensions/Seagate Storage Driver.kext/Contents/PlugIns
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.1.1) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.1.1) Support
[not loaded] com.seagate.driver.SeagateDriveIcons (5.1.1) Support
/Users/[redacted]/Downloads/LCC Installer.app
[not loaded] com.Logitech.Unifying.HID Driver (1.3.1 - SDK 10.8) Support
Startup Items: ℹ️
TuxeraNTFSUnmountHelper: Path: /Library/StartupItems/TuxeraNTFSUnmountHelper
Startup items are obsolete and will not work in future versions of OS X
Launch Agents: ℹ️
[running] com.canon.MFManager.plist Support
[not loaded] com.cooliris.SetLaunchArch.plist Support
[loaded] com.google.keystone.agent.plist Support
[running] com.Logitech.Control Center.Daemon.plist Support
[running] com.logitech.manager.daemon.plist Support
[running] com.micromat.TechToolProAgent.plist Support
[loaded] com.oracle.java.Java-Updater.plist Support
[running] com.seagate.SeagateStorageGauge.plist Support
[running] com.symantec.uiagent.application.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[running] com.cleverfiles.cfbackd.plist Support
[running] com.eltima.ElmediaPlayer.daemon.plist Support
[loaded] com.embraceware.awaken.plist Support
[loaded] com.google.keystone.daemon.plist Support
[loaded] com.macpaw.CleanMyMac2.Agent.plist Support
[running] com.micromat.TechToolProDaemon.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
[loaded] com.prosofteng.DriveGenius.locum.plist Support
[running] com.smithmicro.schedulerdaemon.plist Support
[loaded] com.symantec.liveupdate.daemon.ondemand.plist Support
[failed] com.symantec.liveupdate.daemon.plist Support
[not loaded] com.symantec.sep.migratesettings.plist Support
[running] com.symantec.sharedsettings.plist Support
[running] com.symantec.symdaemon.plist Support
[running] com.taoeffect.ispyd.plist Support
[running] com.wdc.drivemanagerservice.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist Support
[loaded] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist Support
[loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist Support
[loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist Support
[running] com.prosofteng.DGMonitor.plist Support
[running] com.smithmicro.cleaning.schedulermailer.plist Support
[running] com.taoeffect.EspionageHelper.plist Support
User Login Items: ℹ️
Speedy Mac Application (/Applications/Speedy Mac/Speedy Mac.app)
AwakenHelper Application (/Users/[redacted]/Library/Application Support/Awaken/AwakenHelper.app)
GetBackupAgent Application (/Users/[redacted]/Library/Application Support/BeLight Software/Get Backup 2/GetBackupAgent.app)
WDDriveUtilityHelper Application (/Users/[redacted]/Downloads/WD/WD Drive Utilities.app/Contents/Resources/WDDriveUtilityHelper.app)
ClustersHelper Application (/Library/PreferencePanes/Clusters.prefPane/Contents/Resources/ClustersHelper.a pp)
RealPlayer Downloader Agent Application (/Users/[redacted]/Library/Application Support/RealNetworks/RealPlayer Downloader Agent.app)
SAVDiskMountNotify UNKNOWN (missing value)
ScanNotification UNKNOWN (missing value)
Launch Nikon Message Center 2 Application (/Applications/Nikon Software/Nikon Message Center 2/Nikon Message Center 2.app/Contents/SharedSupport/Launch Nikon Message Center 2.app)
Internet Plug-ins: ℹ️
EPPEX Plugin: Version: 10.0 Support
Flash Player: Version: 15.0.0.189 - SDK 10.6 Support
AdobePDFViewer: Version: 9.4.6 Support
Unity Web Player: Version: UnityPlayer version 3.5.3f3 - SDK 10.6 Support
NPVirtools: Version: 4.0 Support
iPhotoPhotocast: Version: 7.0 - SDK 10.8
RealPlayer Plugin: Version: (null) Support
DirectorShockwave: Version: 11.6.8r638 Support
QuickTime Plugin: Version: 7.7.1
FlashPlayer-10.6: Version: 15.0.0.189 - SDK 10.6 Support
GarminGpsControl: Version: 2.9.3.0 Release Support
ToontownBundleManager: Version: (null) Support
CANONiMAGEGATEWAYDL: Version: 3.1.0.2 Support
Silverlight: Version: 5.1.10411.0 - SDK 10.6 Support
OVSHelper: Version: 1.0 Support
CoolirisWebKitPlugin: Version: (null) Support
Google Earth Web Plug-in: Version: 6.1 Support
Flip4Mac WMV Plugin: Version: 3.2.0.16   - SDK 10.8 Support
SharePointBrowserPlugin: Version: 14.4.4 - SDK 10.6 Support
JavaAppletPlugin: Version: Java 7 Update 67 Check version
OfficeLiveBrowserPlugin: Version: 12.3.6 Support
User Internet Plug-ins: ℹ️
BrowserPlus_2.9.2: Version: 2.9.2 Support
Picasa: Version: 1.0 Support
Safari Extensions: ℹ️
DivX Plus Web Player HTML5 <video>
Open in Internet Explorer
DivX HiQ
Aimersoft Video Converter
3rd Party Preference Panes: ℹ️
BrowserPlus Support
Clusters Support
Déjà Vu Support
Flash Player Support
Flip4Mac WMV Support
Java Support
Logitech Control Center Support
Logi Preference Manager Support
MenuMeters Support
Perian Support
Symantec QuickMenu Support
TechTool Protection Support
Tuxera NTFS Support
Time Machine: ℹ️
Skip System Files: NO
Auto backup: YES
Destinations:
iMac TimeMachine [Local]
Total size: 2 TB
Total number of backups: 80
Oldest backup: 2011-09-18 05:21:33 +0000
Last backup: 2014-10-05 20:18:55 +0000
Size of backup disk: Excellent
Backup size 2 TB > (Disk size 0 B X 3)
/sbin excluded from backup!
/usr excluded from backup!
/System excluded from backup!
/bin excluded from backup!
/private excluded from backup!
/Library excluded from backup!
/Applications excluded from backup!
Top Processes by CPU: ℹ️
      2% WindowServer
      0% Speedy
      0% SystemUIServer
      0% RealPlayer Downloader Agent
      0% ps
Top Processes by Memory: ℹ️
288 MB SymDaemon
150 MB Speedy
137 MB Safari
82 MB WebProcess
82 MB coreservicesd
Virtual Memory Information: ℹ️
2.17 GB Free RAM
1.46 GB Active RAM
148 MB Inactive RAM
518 MB Wired RAM
388 MB Page-ins
0 B Page-outs
I hope someone has some ideas! TIA.

Do you have another cable you can test with? Do you have access to another computer with Firewire you can test with?
FireWire Device not Working
FireWire/USB - Quick Assist

Unable to find domain controller for the specified domain. Please explicitly specify the domain controller.

Im getting error "Unable to find domain controller for the specified domain. Please explicitly specify the domain controller." when I try to create an AD connection for my User Profile Service. The entire sharepoint environment is installed
on one server. That server has everyting on it, AD, SQL, Sharepoint, and its the domain controller. I cant figure out why this will not identify?Trevor Fielder

Hi,
Did you get this error when clicking on the Populate Containers button?
If yes, please make sure that you have provide the domain credentials in the account name and password
boxes below when entering the domain information. The account must be granted the replicating directory changes permission on the domain.
You can refer to this blog:
http://www.harbar.net/articles/sp2010ups.aspx
Xue-Mei Chang

Radio Fm in not functioning after upgarding firm w...

Hi,
radio Fm in not functioning after upgarding firm ware 410.21.010
please help to solve it

I am not aware of any "on-device" or native OS FM radio functions. Perhaps it has yet to be implemented, or awaiting a third party to develop an app to use it?
I'd love to have it functional also!
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Transfer of domain created in iweb to a new Mac running OS X Lion 10.7.4. Files not present.

I'm moving a domain created in iweb to a new Mac running OS X Lion 10.7.4. I transferred the domin files via a thumb drive and I can see that the domain contents are present on the new computer. However, when I double click, iweb opens and the domain files are not there. I have also tried dropping the domain files into iweb via Library/Application Support/iweb. Same thing happens when opening from there. Thank you!

I'm a little unclear on what you have done, but the entire contents of your iWeb site should be in the Domain.sites2 file in ~/Library/Application Support/iWeb. (Note that tilde ['~'] character, it's important! That means that we're talking about the Library folder in the user folder, not the one at the root level of the hard drive.)
In order to use that file on a different machine, you must take that entire file and put it in the same folder on the new machine. Be sure you are putting it in the correct Library folder! If you put it in the wrong place, iWeb will not see it, and will open as if you haven't created any sites yet.
If you're having trouble getting to that folder (since Lion makes the user Library folder invisible), hold down the option key while choosing Library from the Finder's Go menu. That will open a new window showing the contents of the user Library folder.

I am trying to setup my new time capsule but it is not working. after entering the airport utility and locating the TC, after I tell the program to continue, the unit just disappear and the setup menu says there is an error. Any idea of what is happening?

I am trying to setup my new time capsule but it is not working. after entering the airport utility and locating the TC, after I tell the program to continue, the unit just disappear from the menu and the setup menu says there is an error. I tried using the wireless connection, and also the cable, but none worked. Any idea of what could be happening?

What are you setting it up as.. join wireless network .. the very worst setup, it will disappear.. reboot the whole network in order modem. router TC.. clients and it will likely reappear.
Tell us what network setup you are using..
If you setup with cable to a computer completely isolated from the network with TC also isolated.. finish the setup of everything you want. .before update.. then plug it into the network. .then restart everything in correct order.. it will work most of the time.

Personal Domain not function after Move the Domain (iWeb) to a New Mac

Similar Messages

Maybe you are looking for