Phone Not Starting after the battery was drained

My Phone's battery was drained and when connected to charge the phone it is not charging. I have kept it for hours but When I try to start my phone it does not do any thing. I am not sure if it is charging or not. Neither anything works please help me with this.

When connected to a power source hold down both the volume up and power button for around 20 seconds then leave it for around 2 hours then check - If this fails then unfortunately your only options are to either return your device to the place of purchase or contact Xperia care http://www.sonymobile.com/global-en/support/contact-us/
For a successful technology, reality must take precedence over public relations, for Nature cannot be fooled.   Richard P. Feynman

Similar Messages

  • My I Pad is not charging, it started after the battery went dead while i was playing a game, when i tried charging it all it does is flash the apple icon and it switches off again, help Pliiz

    my Ipad is not charging, it started after the battery died while i was playing a game, when i tried charging its only flashing the apple icon and it switches off again, help PLIIZ

    Not charging
    1. Reset iPad
    2. Try another wall socket
    3. Try another cable (make sure it's an original Apple cable)
    4. Try another charger (make sure it's an original Apple charger)
    5. Clean Lightning port with compress air or new paint brush

  • A 305- S6825 will not start with the battery and charger. There's no light, no noise on fan or HDD

    PC will not start with the battery and charger. There's no light, no noise on fan, hard drive and CD writer. The hard drive, fan and charger are new. But I was havingproblems and sudden blackouts System 32. Try several times to install theoperating system but the pc turned off suddenly and restarted until I stop working completely. Now it does nothing and no light. I hope it can help me I need torespect and love very much this notebook.
    Thanks in advance
    Jose Echevarria
    [email protected]

    Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections. If it still won't start, remove the battery and start with just the AC power. Next try without the AC power and just the battery.
    - Peter

  • My Itunes will not start after the latest update. I keeo getting error message tEventType : InPageError     P1 : c000009c     P2 : 00000003 . I have tried to reinstall but no joy. Any advise?

    My Itunes will not start after the latest update. I keeo getting error message tEventType : InPageError     P1 : c000009c     P2 : 00000003 . I have tried to reinstall but no joy. Any advise?

    'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
    That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
    XP instructions in the following document: How to perform disk error checking in Windows XP
    Vista instructions in the following document: Check your hard disk for errors
    Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
    Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
    Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

  • Ipod nano 5th gen - works fine when plugged in either to wall or computer and appears to be fully charged but as soon as it is unplugged screen goes blank and will not start - is the battery shot?

    Ipod nano 5th gen - works fine when plugged in either to wall or computer and appears to be fully charged but as soon as it is unplugged screen goes blank and will not start - is the battery shot?

    Yes, your battery is likely toast and in need of replacement.  Not much else for troubleshooting here.  Sorry.
    B-rock

  • My new iPhone4S could not start after the Apple mark disappear, the running screen stand still over 30mn. Can someone tell me how to solve this problem.

    My new iPhone4S could not start after the Apple mark disappear, the running screen stand still over 30mn. Can someone tell me how to solve this problem.
    I tried to connect to iTune hoped to restore the system but iTunes did not reconige it.

    here is link to the apple product feedback website:
    http://www.apple.com/feedback/

  • Why does installation not start after the message "setup wants to make changes"?

    Why does installation not start after the message "Setup wants to make changes.  Type your password to allow this"?

    Hi
    It wants your system's admin password. Standard procedure on Mac for non-admin users
    Thanks

  • My phone has frozen after its battery was completely finished. what to do?

    my iphone 3gs was out of battery completely.
    when i tried to recharge it it didnt recharge and now it is completely frozen.
    what can i do?

    If the battery was discharged and that caused the phone to turn off, it may take up to 30 minutes or more for the phone to respond once it is plugged into the charger.
    I suggest using the charger that came with the phone and plug that into a known good wall outlet. Then wait 30 minutes. After thirty minutes, and with the phone still plugged into the charger reset your phone. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the phone restart.
    If the phone restarts, leave it on the charger until it is fully charged.
    If the phone does not restart then check to make sure the lightning or dock connector port is free of any lint or other debris. You might also try a different cable and different charger. If none of these work its time to have you phone checked out by an Apple technician. Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • TS3274 iPad does not start after the latest software update

    After downloading the latest software update on 25 April 2014, my iPad does not start. The reset mechanism does not have any effect. I would be thankful for advice.

    If the reset doesn't work, force iPad into recovery mode.
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.

  • Phone not working after the software upgrade

    I performed the software upgrade as indicated by the phone in the notifications.
    One the phone rebooted, I proceeded to enter my email accounts and it froze on a white screen with a spinning wheel.
    I rebooted and it continued to freeze.
    I took the battery out, rebooted, still can't add email accounts.  It freezes in the setting section.  I actually can't change any settings.
    If I reply to a text, the screen freezes black.
    If I try to reply to an email, the screen says, "Could not display this message"
    I have wiped it three times, powered off a billion times and still keeps freezing.  The update has been nothing but grief. 
    Any advice??

    Hello 2canoes and welcome to the BlackBerry Support Community Forums.
    Sorry to hear you're experiencing issues with your device after updating your software.
    It's recommended you contact your mobile service provider for investigation on this matter and to open a support ticket with BlackBerry technical support.
    Thanks!
    -HMthePirate
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

  • MacBook Pro will not start after removing battery?

    My MacBook Pro has recently had a brand new battery put it, it's worked perfectly till now. My mouse was very loose so I decided to tighten it up. So I removed the battery, tightened the mouse and replaced the battery back (I've checked it's right) . However it now won't start up! At all, even when plugged into the mains. A faint flicking green light comes on the charger. Please help!
    MacBook Pro 13" 2010 mid (out of warranty) - Mac OS Lion

    Try this:
    PRAM/NVRAM Reset.
    http://support.apple.com/kb/HT1379
    good luck.....if all else fails, bring it to Apple and see what's going on with it.  Just don't let them know that you took the battery out.

  • Firefox 4 download will not start after the download is complete. It just doesn't run (Windows Vista), and can't be found in the program list. Solutions?

    I have tried to open it both as the original user and as administrator. Nothing happens after I indicate that it should open

    I was able to work the problem out by logging in as administrator. When the download was finished and extracted, a choice was offered to save rather than run. So I saved it on the desktop, and then right clicked on the icon, and selected "run as administrator". It then ran and installed with no problem.

  • FE service cannot start after the update was done

    Hi,
    We are installing lync 2013 standard Edition server on windows server 2008 R2.
    Certificates are public ones and they are from Digicert.
    We managed to go to step 3 (certificates part is ok).
    We cannot start the FE service.
    We tried everything regarding resetting fabric state, registrat  etc.
    We made the update with the newest patch (February 2015).
    FE cannot be started:
    We still got the errors:
    "Failed to sync data for Routing group {19F4D868-D0A1-53D8-BE89-1BFA7BDE645E} from backup store.
    Cause: This may indicate a problem with connectivity to backup database or some unknown product issue.
    Resolution:"
    "This process was not able to update its health status
    The Audio-Video Conferencing Server failed to send health notifications to the MCU factory at.."
    and so on...
    as could be seen under link: http://troubleshootinglync.blogspot.com/2014/03/lync-2013-front-end-service-wont-start.html
    Any idea what could be wrong?

    Hi iron_folower,
    You can follow the steps below to troubleshoot your problem:
    1. Install the Root Certificate and the Intermediate Certificate from Digicert.
    2. From:
    https://social.technet.microsoft.com/Forums/lync/en-US/506821e2-d3fe-42bd-a6dc-daed6c5f0df6/the-audiovideo-conferencing-server-failed-to-send-health-notifications-to-the-mcu-factory-at?forum=ocsconferencing
    Try to create the REG key:
    HKLM\System\CurrentControlSet\Control\SecurityProviders\SCHANNEL and create a dword entitled
    Sendtrustedissuerlist with a hax value of 0.
    3. Reinstall the base OS features:
    Import-Module ServerManager
    Add-WindowsFeature Web-Dyn-Compression,desktop-experience,RSAT-ADDS,Web-Server,Web-Scripting-Tools,Web-Windows-Auth,Web-Asp-Net,Web-Log-Libraries,Web-Http-Tracing,Web-Stat-Compression,Web-Default-Doc,Web-ISAPI-Ext,Web-ISAPI-Filter,Web-Http-Errors,Web-Http-Logging,Web-Net-Ext,Web-Client-Auth,
    Web-Filtering,Web-Mgmt-Console,Msmq-Server,Msmq-Directory
    Best regards,
    Eric
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Why does it say can not open  iphone mobile device service not started after the udate fixes?

    can someone please help after i update my soft ware to fix sum bug issues now when i hook up my iphone to my laptop it say can not open iphone mobile device is not started

    Check the links listed in the More Like This box on the right of this window.

  • HT3180 My Apple TV is not starting after the software updates

    I have tried to use menu and down on remote , disconnected power supply etc but nothing is working to restart the Apple TV

    Welcome to the Apple Community.
    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Devices list, and then click Restore.
    (You may already have a micro USB cable if you have a camera or other digital device)

Maybe you are looking for