Photosmart all in one 7510 not recognized but connected to wireless

I have a NETGEAR Router, WNDR3800.  It is a dual band router running both a 5GHz and 2.4GHz network.  I have never been able to maintain a working connection to the printer.  After I reload the printer onto the known printers for the Mac, if the printer goes idle I am never able to re-establish the printer for use.
The mac and the printer are both connected to the same 2.4GHz network.
The network has WPA2-PSK [AES] security enabled
The network configuration page shows the network status as ready with Bonjour enabled
The Mac has never been able to pick up the printer wirelessly. I have always had to set it up via USB connection to get the Mac and printer to talk to each other.  The printer will join the wireless network without the Mac, however, if i complete the process that way then the Mac will never see the printer.
Recenty updated to OS X Mavericks. Printer would not work although shows the status above.  Downloaded new drivers for the OS X update.  When running the HP utility to set up the printer, it was not recognized on the network. (reverified both were connected to the same 2.4Ghz network).  Attempted to connect via USB.  When establishing the network configuration for the printer on the HP Utility via the USB cable reveived an error message that stated the following (paraphrased):
Your printer is connected to the network but is not recognized by your Mac check with hp print website help (essentially)
I have reset the router and re-tried the above process. No difference
I have reloaded all the software and restarted the mac and printer. No difference.
I have manual assigned the IP Address for the printer and reserved the address on the router.  Re-attempted to connected wirelessly and via usb. No difference.
I am at a loss as to what I can do next.  Not sure if it a router issue or printer issue but I have no other issues with any equipment on this router both establishing connections to and communicating between several other devices.  I would appreciate any help with this issue.

Hello dan_man182 and welcome the HP Forums!
I understand you're having an issue printing wirelessly. I can provide help for you.
Follow this document please: 'Unable to Find Printer' Error Message Displays on the Computer During a Wireless Network Installati...
Another tip I can give you is the security on your router. For some reason the connection may not like the WPA2-PSK [AES] security type. Try changing that to [TKIP] and see if that helps.
Furthermore, if your 5.0Ghz is active, but you are not using it, try disabling the 5.0Ghz frequency altogether. There is a possibility it could interfere somehow.
That is my personal thought on the matter, if you want a full detailed description on router settings you can refer to this: Suggested Router Configurations
Source: VisionAiry
Thank you for choosing the HP Forums! Let me know if that helps!
GiGi10
I used to work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the left to say “Thanks” for helping!

Similar Messages

  • Photosmart all in one B210a showing offline - no connection to MAC OSX 10.8.5 nor IPad

    NEVERMIND!  It's working now!  (Of course as soon as I give up after 4 hours and contact the Forum, NOW it works!!)
    Thanks anyway!
    Changed my router from the factory default name and password settings.  Reconfigured printer to recognize router, and the display & printed page said there was no problem / set up successful.  Then I downloaded the most recent update to my printer from HP website.  The only "device" found was HP Photosmart "[F7E632] Bonjour multifunction."  (I never saw anything prior to this with the F-coding nor "bonjour" information.)  Now when I try to print from the Mac, the print que message says the printer "may not exist or is unavailable at this time."  When I try to print from the IPad, it says the printer "is offline."
    I'm not that computer savvy, and I am COMPLETELY at a loss as to how to troubleshoot this.  Can someone help me?  
    Thank you.

    Hi @Riversend ,
    I understand you were able to resolve the issue you were experiencing. I am sorry to hear that it had been so time consuming. If you ever need support in the feature of course you can come back to the HP Forums, but you can always use your printer support page as well.
    HP Photosmart Plus e-All-in-One Printer - B210a support
    Although you no longer require assistance, I want you to know that we are here to help. Thanks for choosing HP.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • Itunes all of a sudden not recognizing ipod connection

    just an hour before this happened i made an update to my ipod then this happend. i re-installed the ipod and itunes software, but nothing. this ipod is really aggrevating me b/c u expect less hassle from a $300 product.
    please help!!

    is your ipod functioning normally?
    if itunes is not recognizing it, read the following:
    http://docs.info.apple.com/article.html?artnum=61711

  • After move, all-in-one will not print or connect

    My All-In-One was working fine before we moved.  Now, it says it isn't connected to the computer. I have tried connecting via ethernet and USB as well as wirelessly.  I have downloaded the HP doctor, new drivers, and I am at my wits end.  Really need the printer capability!  Copy and fax are working fine.

    Hello @momof3cs,
    Welcome to the HP Support Forums!
    I would like to assist you today with resolving the communication issue you're experiencing when attempting to print from your Windows 7 computer to your HP Officejet Pro L7580 All-in-One Printer. Now, with a new location comes a new setup of your printer. If your printer was previously configured over your network you will need to reconfigure the network settings on your product to re-establish that communication. Please follow the steps below to correct this connection issue.
    If you have a USB Cable attached to your printer, please disconnect that now. 
    If you have an Ethernet Cable attached to your printer, please disconnect that as well.
    Step 1: Restore Printer:
    For troubleshooting purposes, it is important to have a nice clean slate to work with. Therefore, I am going to have you restore any network settings on your printer.
    Select the Setup button on the front panel of your printer
    Right arrow to Tools and select OK
    Right arrow to Restore Factory Defaults and select OK
    Once the Restore is complete, please proceed to the next step.
    Step 2: Uninstall Drivers:
    Click on your Start menu
    Select All Programs
    Select the HP folder
    Select your HP Officejet
    Select Uninstall
    Follow the onscreen instructions to complete the uninstall.
    Step 3: Install Drivers:
    If you want to use the printer over an Ethernet connection, please plug the ethernet cable in from the rear of your  printer directly into your router
    Next, click here to download the drivers for your printer
    Once the website opens select the Download button on the top left
    If prompted, please allow the download to Run
    Once the download is complete, please follow the onscreen instructions to install your network printer
    Once the installation is complete, please test your machine to ensure that everything is functioning.
    If you also want your printer installed with a USB Cable, please follow the steps below.
    Click on your Start menu
    Select All Programs
    Select the HP folder
    Select your HP Officejet
    Select 'Connect a Device' or 'Add a Device'
    Choose that you want  to install for USB
    Only plug in the USB Cable when the installer prompts you to
    Once this install is complete, please test printing to ensure everything is working.
    If you want your network printer to be the default printer you will need to go to your Start menu, click on Devices and Printers, right click on your network Officejet and select Set as Default Printer.
    Please respond to this post with the result of your troubleshooting. Best of luck!
    X-23
    I work on behalf of HP
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping!

  • One iphone not recognized, but another is in Windows XP

    I have a user that has an odd problem.
    This person has 2 iPhones - a 4 and a 4s.  This week the 4 stopped being recognized by Windows XP on his laptop when he plugs it in.  It won't charge from that computer either.  However if you plug it into another computer it will see it fine (and charge it).  The 4s will recognize and charge fine on his computer.
    To recap:
    4s - works fine - syncs and charges when connected to his laptop or any other computer.
    4 - not seen by his computer, will not charge.  Plugged into a different computer, it works fine.
    I'm kinda stumped on this one and I haven't seen a precident that matches this problem.
    Any help would be greatly appreciated!

    I FIGURED IT OUT. THANK FREAKING GOD!
    This is what I did:
    I went to control panel and unistalled iTunes completely, then I installed 10.6.3
    http://support.apple.com/downloads/#itunes which you can find here
    It came up with an error saying that my library had beed used with a more updated verision, basically had to upgrade. I installed iTunes 10.7
    After it had installed and iTunes was running I hooked up both my iPhone and my flash drive, I have more than 1 usb port I figure most computers do now, and by the time and date in the bottom right corner a small icon came up showing that I had devices hooked up. It showed both my iPhone (but did not know what it was) and my flash drive. If you right click on the iPhone it has the option to Troubleshoot it. I did it and my iPhone 5 now FINALLY SYNCS!
    I'm sooo happy now.

  • C6150 All In One is not recognized over network

    My printer works fine for printing over the network.  My problem is that I cannot initiate a scan to computer, or initiate from within HP solution center.  I can access and interact with my printer directly via the web browser interface.  The HP driver install and HP home network diagnostic utility all find the printer OK on the network, but the diagnostic utility keeps saying that software is missing that is necessary to run the printer over the network.  I have uninstalled all HP software, then downloaded the full version of the latest HP software suite and installed it - all OK except now when I try to run Solution center it no longer even gets to the main menu - an error message comes up and says no HP devices were found and quits.  When obtaining software from the HP site I was careful to specify XP as the OS and have not tried anything that does not have XP listed as compatible.
    I still can connect to it directly and print.  I have looked at every possible driver that HP has on the site.  I have run the scan diagnostic - It verifies the connection OK but when it gets to the driver section of the test it crashes and a Windows error message comes up and says it has encountered a problem and has to close.
    I am running XP Home with all of the updates installed.

    Hi,
    seeing as you can acces the printer via the browser, so directly from its ip adress the connection is ok. What in these cases is most likely is that there is something on your computer blocking HP software ability to check out the network. Most likely something like a firewall or virusscanner.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Although I work for HP my posts and replies are my own
    Please mark the post that solves your problem as "Accepted Solution"

  • HP Photosmart All-in-One 7510 Series - won't print

    I just reinstalled driver. When I tried printing it said driver offline. How do I get the driver back online? I have already downloaded all the updates. The messages say that the printer is fully operational.

    Hi,
    Please touch the wireless symbol (2nd from left) on the printer control panel. What do ypu see ?
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • HP Deskjet 3050 All in One Mac not working w USB or Wireless

    I have tried to setup my nen to me printer both via USB and Wireless connection. The computer did locte the priinters wifi signal but that was as far as i could get with that. The USB connection was a little better but when I added the printer there was not an option for the software matching the product number so i used the generic. Once setup I have tried to print and the printer icon comes up momentarilly then  disapears. I am lost. Help please!!!

    Hello there! Welcome to the forums @colemanthompson ,
    I understand you are running into troubles when connecting your Deskjet 3050 to your Mac. I will certainly do my best to help! Please first respond to me with which Mac OS X you are running.
    Thank you
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • HT1338 I have updated my new MacBook Pro for HP Photosmart All-in-One, but it still will not scan - it will print, but will not scan. How can I fix this?

    I have installed the updates for my HP Photosmart All-in-One c309a.  It prints, but will not scan.  Tells me to update - I did that, but still won't scan.  Any suggestions to make the scanner work?
    This all worked perfectly with my old 2008 MacBook Pro.

    Have you tried scanning from Image Capture or Preview?
    A current driver is shown to be available for Mavericks (auto-downloaded):
    http://support.apple.com/kb/ht3669#HP
    But many people have found that manufacturer scanning control software doesn't work. They have to use the Apple-provided software.

  • Problem with drivers for HP B109 a-m all-in-one, have printer working but not scanner in windows 8

    Still have a problem with the drivers in Windows 8 release preview, for my HP B109 a-m all-in-one, have printer working but not scanner, is there any chance of a fix before final release of Windows 8 ?.

    Review my post here:
    http://h30434.www3.hp.com/t5/Windows-8-Release-Preview/SOLUTION-Get-Win-7-Printer-Drivers-HP-Solutio...
    And see if something similar will work for you.

  • Okay so i recorded a song but each part comes out as like take 1, i have 10 takes. how can i put them all together as one take, to make one song all in one take not small pieces of a song.

    okay so i recorded a song but each part comes out as like take 1, i have 10 takes. how can i put them all together as one take, to make one song all in one take not small pieces of a song. like i hit record and sang the entire song but when i hit play it was in pieces not just one song like it was in ten takes. is there any way i can blend it all into one take, to make one clear song?

    You're not very clear in stating your problem. Maybe it's terminology: "takes" in recording lingo (and in GB lingo) are different version of exactly the same part in a song, so you only want one of them in the end. Please tell us exactly what you did and what it is that you don't like.

  • Ink System Failed error on Photosmart All in One C7180

    I have a Photosmart All in One C7180.  I am getting the Ink System has failed....Error: 0xc05d0281 message.  I have tried all of the suggested solutions to make this go away but it seems to be a hardware failure.  Is this something that can be fixed/replaced or is the printer history?  I don't want to pay for an HP service call if this is not something that can be fixed/replaced.  Thank you for any help

    Hello there! Welcome to the forums @cleardaypdx,
    I read your post about the scanning troubles you're facing with your moms Photosmart C309a and wanted to share my suggestion with you.
    Click here to see the guide and follow the steps: 'Another program has control of the scanner' Message Displays on the Computer When Scanning
    I hope that helps, have a terrific day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Can my hp photosmart all-in-one 7200 printer connect to ipad 2 via bluetooth?

    I have a hp photosmart all-in-one 7200 printer with a hp blue tooth dongle.  It works well with my cameras, but I cannot get my ipad 2 to recognize the printer.

    Hi,
    Printing via Bluetooth from an iPad is not possible due to iOS limitations, as Apple did not include the Bluetooth printing protocol in the iOS.
    If your printer is HP Photosmart C7200, you may use the HP ePrint Home & Biz App to print from your iPad through your home network
    However for the Officejet 7200 your only option is to look for any available 3rd party printing solution from the App Store.
    Regards,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • After upgrading to mavericks how can I connect my HP PSC 2510 photosmart all-in-one printer to my mac?

    After I upgraded my macbook air to mavericks, my HP PSC 2510 photosmart all-in-one printer doesn't connect to my macbook air.  When I try to launch the all-in-one installer from the HP CD that came with the printer, I get a message saying it cannot open because powerPC is not supported.  The HP site has not been helpful in resolving this issue.  My understanding is I first must connect the printer to the wireless system (I use airport extreme) before using airplay for printer software upgrade.

    Your suggestion is helpful, but after some digging on the HP site I found a detailed solution to my problem.  The link is: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01749025&tmp_task=setupCate gory&cc=us&dlc=en&jumpid=reg_r1002_usen_c-001_title_r0001&lc=en&product=303770

  • Poor photo quality in Photosmart All-in-one B209a

    Hello All,
    I purchased a HP Photosmart 8150 printer back in 2005 for the sole purpose of making prints. Recently the thing crapped out to the extent that the repair would cost more than the printer did. It was recommended that we purchase a new printer. We bought the HP Photosmart All-in-one B209a. Most of its use will be printing photo too. 
    The main issue I am having is in the noticeably poor quality in the prints compared to the 8150. I was shocked since it is advertised as a good photo printer, but I can't believe that in 5 years this the quality has gone down? Can anyone confirm that this is the case: Is it just that the previous 8150 model was a better printer for photos or is there something wrong with the B209a. The quality in the shadows is especially disturbing and true black is never achieved, rather a very grainy shade of grey comes up. I have gone through the Print - Quality Toubleshooting guide online here, but the problem persists.
    Any recommendations? 
    -Ronan

    Hi
    i have just bought the same printer and when i printed some photos using the paper supplied the pictures actualy seemed dark. I am not happy with this as you would expect the print quality to improve. does anybody know why the print quality is not as advertised?
    Thanks
    ronesyzf wrote:
    Hello All,
    I purchased a HP Photosmart 8150 printer back in 2005 for the sole purpose of making prints. Recently the thing crapped out to the extent that the repair would cost more than the printer did. It was recommended that we purchase a new printer. We bought the HP Photosmart All-in-one B209a. Most of its use will be printing photo too. 
    The main issue I am having is in the noticeably poor quality in the prints compared to the 8150. I was shocked since it is advertised as a good photo printer, but I can't believe that in 5 years this the quality has gone down? Can anyone confirm that this is the case: Is it just that the previous 8150 model was a better printer for photos or is there something wrong with the B209a. The quality in the shadows is especially disturbing and true black is never achieved, rather a very grainy shade of grey comes up. I have gone through the Print - Quality Toubleshooting guide online here, but the problem persists.
    Any recommendations? 
    -Ronan

Maybe you are looking for