PLease Help!! Leopard and Blue Screen

I know there is a lot of discussion out there about a blue screen after installing Leopard. Well I had leopard installed and working for a while and then one day i started having issued where iTunes would lock up my MacBook and I would have to restart the MacBook because i could not stop it from "determining gap less playback" It would do it every time i plugged in my iPhone or my iPod. So everything was working great other than the iTunes issue. Then one night while my wife was using the MacBook it turned off on her so she proceeded to turn it back on only to have it boot up to a blue screen. Keep in mind we had been running Leopard for a few months this was not a brand new install. I purchased my MacBook used from a fried who did not provide me with the CD/DVD's to restore the MacBook since he lost them in his move. So I have searched far and wide trying to resolve this issue. I have booted into Single user mode and did the command prompt options...
1. Reboot into single-user mode (hold Cmd-S while booting machine)
2. Follow the directions OSX gives you when you get to the prompt (I think these were them - just type the two commands it tells you to):
fsck -fy /
/sbin/mount -uw /
3. Remove the following files:
rm -rf /Library/Preference Panes/Application Enhancer.prefpane
rm -rf /Library/Frameworks/Application Enhancer.framework
rm -rf /System/Library/SystemConfiguration/Application Enhancer.bundle
rm -rf /Library/Preferences/com.unsanity.ape.plist
4. Exit, to continue booting normally
exit
restart
I have tried to boot the MacBook in safe mode with no luck. I think i have done everything i can. I called Apple support and was told that the MacBook is out of warranty by 408 days. Can i buy the restore CD/DVD? Is there something that I am missing? What am I not doing? Please help me???

Does the Blue Screen happen after the Gray screen with the Apple logo and the spinning gear below it or when you turn on the computer you see the blue screen right away? You can try resetting the PRAM. Turn on the computer while holding the CommandOption+PR. These buttons will reboot your computer manually so let go after you saw the computer restart by itself. You also mentioned that you installed Leopard on your computer. So do you still have the Leopard install disk with you? If you do, boot from that disk. With the Leopard disk inside your optical drive, press the C key while turning it on. Once booted, try do repair the disk permissions and disk in Disk Utility.
Hope this helps.

Similar Messages

  • Blank Black Screen And Blue Screen. Do I Need To Do Reflow To Ati Chipset?

    Hello i want to tell you my problems and what i did until now.
    I have hp pavilion dv3 4150st. I was using win7 64 bit . and i was geting an error that says "display driver amd driver stopped responding and has successfully recovered".I started to get this eror often . And a few days later  my pc startet to get blue screen errcor after a few second later than display driver error. . And  after 2-3 blue screen error i lost my screen. It was blank black . when i restart pc the screen was blank black. there was no image. When i started to fix another monitor, i saw screen . And i installed the win 7 with another external monitor. Bu i had still black screen after install the windows.. Itand  was still black after i remove the ectgernal monitor. I installed bios again but i had still black screen. And i tried the install ati display driver after installing windows . But after i installed the display driver, i had the blue screen error again. And now i have still both blank black screen and blue screen problem. 
    I cleaned the motherboard. I resetted bios. I installed bios. i installed windows again. i installed ati display driver.But these couldnt solve the problems. Please can you tell me what can i do now ?

    Hi beginner_2012,
    Thank you for your post, I will do my best to assist you.
    I grasp that you were getting the error "display driver amd driver stopped responding and has successfully recovered" quite often.  Then a  few days later you got the blue screen then the above error message, after 2 -3 more errors the screen is now blank or black. Here is a document to assist you with this.  Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot.
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • X-Fi Titanium and Blu-Screen (Win XP)

    %[ Hi ti all, i am a new user and, of course, i have my first big problem with creative drivers/software.
    Before installation of audio card all worked greatly but after i get a blu screen at shut down or at reboot (is the same).
    I used the latest version of the drivers available on the web (2.7.0006).
    I removed audio card and drivers and all works greatly, too.
    I reinstalled audio card + drivers and blu screen at shut down/reboot appears again.
    Anyone knows the solution.
    Audio card works correctly but with this blue screen ?the creative console don't save any settings, so every time
    i turn on the pc i have to configure it (effect, mixer, number of speakers, mic amplifiers, etc. etc.).
    Please help me.
    This is my configuration:
    Cpu Intel Core i7 920
    M/b Asus P6T (bios 0603)
    Ram 6 Gb DDR3 (3x2Gb DDR3 Corsair) ('cause i have Vista64 on another partition)
    ATI Radeon HD4890 Gb?
    HD Seagate 500 Gb
    Thanks in advance.

    Anyone?Message Edited by Rayman968 on 08-0-2009 2:47 PM

  • Dmp file and blue screen error Windows 7

    Hi,
    Just wondering if someone can tell me how to read the dmp file created after the blue screen appears ?
    I have just recently upgraded my Toshiba P300 from Vista 64 bit to Windows 7 Home Prem 64 bit. 
    I dont know why Windows 7 keeps crashing and so far I have no idea of how to open the .dmp
    file (I have zipped the dmp file and attahced below).
    http://cid-7a99d6152c55359c.skydrive.live.com/self.aspx/.Public/minidump/022710-26223-01.zip
    The message that I been given so far says :
    Problem signature:
      Problem Event Name:                        BlueScreen
      OS Version:                                          6.1.7600.2.0.0.768.3
      Locale ID:                                             3081
      Additional information about the problem:
      BCCode:                                               a
      BCP1:                                                    FFFFF6FC40052000
      BCP2:                                                    0000000000000002
      BCP3:                                                    0000000000000000
      BCP4:                                                    FFFFF80002E62322
      OS Version:                                          6_1_7600
      Service Pack:                                       0_0
      Product:                                               768_1
      Files that help describe the problem:
      C:\Windows\Minidump\022710-26223-01.dmp
      C:\Users\Caroline\AppData\Local\Temp\WER-125393-0.sysdata.xml

    I have try step 1 and didnt boot up the window normaly...same thing happened
    Window 7 is loading...then boom the screen failed and blue screen appear...
    there is the latet crash report
    Version=1
    EventType=BlueScreen
    EventTime=129810543666556864
    ReportType=4
    Consent=1
    ReportIdentifier=9fb6a978-99f3-11e1-9b67-fa9a72be4846
    IntegratorReportIdentifier=050912-14508-01
    Response.type=4
    DynamicSig[1].Name=OS Version
    DynamicSig[1].Value=6.1.7601.2.1.0.256.1
    DynamicSig[2].Name=Locale ID
    DynamicSig[2].Value=3084
    UI[2]=C:\Windows\system32\wer.dll
    UI[3]=Windows has recovered from an unexpected shutdown
    UI[4]=Windows can check online for a solution to the problem.
    UI[5]=&Check for solution
    UI[6]=&Check later
    UI[7]=Cancel
    UI[8]=Windows has recovered from an unexpected shutdown
    UI[9]=A problem caused Windows to stop working correctly.  Windows will notify you if a solution is available.
    UI[10]=Close
    Sec[0].Key=BCCode
    Sec[0].Value=a
    Sec[1].Key=BCP1
    Sec[1].Value=0000000000000000
    Sec[2].Key=BCP2
    Sec[2].Value=0000000000000002
    Sec[3].Key=BCP3
    Sec[3].Value=0000000000000001
    Sec[4].Key=BCP4
    Sec[4].Value=FFFFF8000308BB7E
    Sec[5].Key=OS Version
    Sec[5].Value=6_1_7601
    Sec[6].Key=Service Pack
    Sec[6].Value=1_0
    Sec[7].Key=Product
    Sec[7].Value=256_1
    File[0].CabName=050912-14508-01.dmp
    File[0].Path=050912-14508-01.dmp
    File[0].Flags=589826
    File[0].Type=2
    File[0].Original.Path=C:\Windows\Minidump\050912-14508-01.dmp
    File[1].CabName=sysdata.xml
    File[1].Path=WER-27253-0.sysdata.xml
    File[1].Flags=589826
    File[1].Type=5
    File[1].Original.Path=C:\Users\Moz\AppData\Local\Temp\WER-27253-0.sysdata.xml
    File[2].CabName=Report.cab
    File[2].Path=Report.cab
    File[2].Flags=196608
    File[2].Type=7
    File[2].Original.Path=Report.cab
    FriendlyEventName=Shut down unexpectedly
    ConsentKey=BlueScreen
    AppName=Windows
    AppPath=C:\Windows\System32\WerFault.exe
    ive also have got a AI SUITE II crash...
    Version=1
    EventType=APPCRASH
    EventTime=129809041249476693
    ReportType=2
    Consent=1
    UploadTime=129809041250516752
    ReportIdentifier=ddea075d-9895-11e1-9a9f-eb38eba38a41
    IntegratorReportIdentifier=ddea075c-9895-11e1-9a9f-eb38eba38a41
    WOW64=1
    Response.BucketId=2555721005
    Response.BucketTable=1
    Response.type=4
    Sig[0].Name=Application Name
    Sig[0].Value=AI Suite II.exe
    Sig[1].Name=Application Version
    Sig[1].Value=1.0.0.40
    Sig[2].Name=Application Timestamp
    Sig[2].Value=00000000
    Sig[3].Name=Fault Module Name
    Sig[3].Value=KERNELBASE.dll
    Sig[4].Name=Fault Module Version
    Sig[4].Value=6.1.7601.17651
    Sig[5].Name=Fault Module Timestamp
    Sig[5].Value=4e211319
    Sig[6].Name=Exception Code
    Sig[6].Value=0eedfade
    Sig[7].Name=Exception Offset
    Sig[7].Value=0000b9bc
    DynamicSig[1].Name=OS Version
    DynamicSig[1].Value=6.1.7601.2.1.0.256.1
    DynamicSig[2].Name=Locale ID
    DynamicSig[2].Value=3084
    DynamicSig[22].Name=Additional Information 1
    DynamicSig[22].Value=0a9e
    DynamicSig[23].Name=Additional Information 2
    DynamicSig[23].Value=0a9e372d3b4ad19135b953a78882e789
    DynamicSig[24].Name=Additional Information 3
    DynamicSig[24].Value=0a9e
    DynamicSig[25].Name=Additional Information 4
    DynamicSig[25].Value=0a9e372d3b4ad19135b953a78882e789
    UI[2]=C:\Program Files (x86)\ASUS\AI Suite II\AI Suite II.exe
    UI[3]=AI Suite II has stopped working
    UI[4]=Windows can check online for a solution to the problem.
    UI[5]=Check online for a solution and close the program
    UI[6]=Check online for a solution later and close the program
    UI[7]=Close the program
    LoadedModule[0]=C:\Program Files (x86)\ASUS\AI Suite II\AI Suite II.exe
    LoadedModule[1]=C:\Windows\SysWOW64\ntdll.dll
    LoadedModule[2]=C:\Windows\syswow64\kernel32.dll
    LoadedModule[3]=C:\Windows\syswow64\KERNELBASE.dll
    LoadedModule[4]=C:\Windows\syswow64\WINTRUST.DLL
    LoadedModule[5]=C:\Windows\syswow64\msvcrt.dll
    LoadedModule[6]=C:\Windows\syswow64\CRYPT32.dll
    LoadedModule[7]=C:\Windows\syswow64\MSASN1.dll
    LoadedModule[8]=C:\Windows\syswow64\RPCRT4.dll
    LoadedModule[9]=C:\Windows\syswow64\SspiCli.dll
    LoadedModule[10]=C:\Windows\syswow64\CRYPTBASE.dll
    LoadedModule[11]=C:\Windows\SysWOW64\sechost.dll
    LoadedModule[12]=C:\Windows\syswow64\ADVAPI32.DLL
    LoadedModule[13]=C:\Windows\system32\VERSION.DLL
    LoadedModule[14]=C:\Windows\WinSxS\x86_microsoft.windows.common-controls_6595b64144ccf1df_5.82.7601.17514_none_ec83dffa859149af\COMCTL32.DLL
    LoadedModule[15]=C:\Windows\syswow64\GDI32.dll
    LoadedModule[16]=C:\Windows\syswow64\USER32.dll
    LoadedModule[17]=C:\Windows\syswow64\LPK.dll
    LoadedModule[18]=C:\Windows\syswow64\USP10.dll
    LoadedModule[19]=C:\Windows\system32\MSIMG32.DLL
    LoadedModule[20]=C:\Windows\syswow64\SHELL32.DLL
    LoadedModule[21]=C:\Windows\syswow64\SHLWAPI.dll
    LoadedModule[22]=C:\Windows\syswow64\OLE32.DLL
    LoadedModule[23]=C:\Windows\syswow64\OLEAUT32.DLL
    LoadedModule[24]=C:\Windows\system32\IMM32.DLL
    LoadedModule[25]=C:\Windows\syswow64\MSCTF.dll
    LoadedModule[26]=C:\Windows\system32\CRYPTSP.dll
    LoadedModule[27]=C:\Windows\system32\rsaenh.dll
    LoadedModule[28]=C:\Windows\syswow64\imagehlp.dll
    LoadedModule[29]=C:\Windows\system32\ncrypt.dll
    LoadedModule[30]=C:\Windows\system32\bcrypt.dll
    LoadedModule[31]=C:\Windows\SysWOW64\bcryptprimitives.dll
    LoadedModule[32]=C:\Program Files (x86)\ASUS\AI Suite II\AsMultiLang.dll
    LoadedModule[33]=C:\Windows\system32\WINSPOOL.DRV
    LoadedModule[34]=C:\Program Files (x86)\ASUS\AI Suite II\ImageHelper.dll
    LoadedModule[35]=C:\Windows\WinSxS\x86_microsoft.windows.gdiplus_6595b64144ccf1df_1.1.7601.17514_none_72d18a4386696c80\gdiplus.dll
    LoadedModule[36]=C:\Windows\system32\USERENV.dll
    LoadedModule[37]=C:\Windows\system32\profapi.dll
    LoadedModule[38]=C:\Windows\system32\GPAPI.dll
    LoadedModule[39]=C:\Windows\system32\cryptnet.dll
    LoadedModule[40]=C:\Windows\syswow64\WLDAP32.dll
    LoadedModule[41]=C:\Windows\system32\SensApi.dll
    LoadedModule[42]=C:\Windows\system32\Cabinet.dll
    LoadedModule[43]=C:\Windows\system32\DEVRTL.dll
    LoadedModule[44]=C:\Windows\system32\WindowsCodecs.dll
    LoadedModule[45]=C:\Windows\system32\WINHTTP.dll
    LoadedModule[46]=C:\Windows\system32\webio.dll
    LoadedModule[47]=C:\Windows\syswow64\WS2_32.dll
    LoadedModule[48]=C:\Windows\syswow64\NSI.dll
    LoadedModule[49]=C:\Windows\system32\credssp.dll
    LoadedModule[50]=C:\Windows\syswow64\mswsock.dll
    LoadedModule[51]=\\.\globalroot\systemroot\syswow64\mswsock.dll
    LoadedModule[52]=C:\Windows\syswow64\WININET.dll
    LoadedModule[53]=C:\Windows\syswow64\Normaliz.dll
    LoadedModule[54]=C:\Windows\syswow64\iertutil.dll
    LoadedModule[55]=C:\Windows\syswow64\urlmon.dll
    LoadedModule[56]=C:\Windows\system32\Secur32.dll
    LoadedModule[57]=C:\Windows\System32\wshtcpip.dll
    LoadedModule[58]=C:\Windows\System32\wship6.dll
    LoadedModule[59]=C:\Windows\system32\IPHLPAPI.DLL
    LoadedModule[60]=C:\Windows\system32\WINNSI.DLL
    LoadedModule[61]=C:\Windows\system32\dhcpcsvc6.DLL
    LoadedModule[62]=C:\Windows\system32\dhcpcsvc.DLL
    LoadedModule[63]=C:\Windows\syswow64\CFGMGR32.dll
    LoadedModule[64]=C:\Windows\system32\uxtheme.dll
    LoadedModule[65]=C:\Windows\system32\DNSAPI.dll
    LoadedModule[66]=C:\Program Files (x86)\Bonjour\mdnsNSP.dll
    LoadedModule[67]=C:\Windows\system32\rasadhlp.dll
    LoadedModule[68]=C:\Windows\System32\fwpuclnt.dll
    LoadedModule[69]=C:\Program Files (x86)\ASUS\AI Suite II\AssistFunc.dll
    LoadedModule[70]=C:\Windows\system32\PROPSYS.dll
    LoadedModule[71]=C:\Windows\WinSxS\x86_microsoft.windows.common-controls_6595b64144ccf1df_6.0.7601.17514_none_41e6975e2bd6f2b2\comctl32.dll
    LoadedModule[72]=C:\Windows\system32\apphelp.dll
    LoadedModule[73]=C:\Windows\syswow64\CLBCatQ.DLL
    LoadedModule[74]=C:\Windows\system32\wpdshext.dll
    LoadedModule[75]=C:\Windows\system32\WINMM.dll
    LoadedModule[76]=C:\Windows\System32\shdocvw.dll
    LoadedModule[77]=C:\Windows\SysWOW64\ieframe.dll
    LoadedModule[78]=C:\Windows\syswow64\PSAPI.DLL
    LoadedModule[79]=C:\Windows\SysWOW64\OLEACC.dll
    LoadedModule[80]=C:\Windows\syswow64\SETUPAPI.dll
    LoadedModule[81]=C:\Windows\syswow64\DEVOBJ.dll
    LoadedModule[82]=C:\Windows\system32\ntmarta.dll
    LoadedModule[83]=C:\Program Files (x86)\ASUS\AI Suite II\pngio.dll
    LoadedModule[84]=C:\Program Files (x86)\ASUS\AI Suite II\AsAcpi.dll
    LoadedModule[85]=C:\Program Files (x86)\ASUS\AI Suite II\asacpiEx.dll
    LoadedModule[86]=C:\Windows\system32\RpcRtRemote.dll
    State[0].Key=Transport.DoneStage1
    State[0].Value=1
    State[1].Key=DataRequest
    State[1].Value=Bucket=-1739246291/nBucketTable=1/nResponse=1/n
    FriendlyEventName=Stopped working
    ConsentKey=APPCRASH
    AppName=AI Suite II
    AppPath=C:\Program Files (x86)\ASUS\AI Suite II\AI Suite II.exe

  • IPad Air with iOS 8.02 freezes and blue screen appears. What should be done ? Why is this happening ?

    IPad Air with iOS 8.02 freezes and blue screen appears. What should be done ? Why is this happening ?

    If nothing else works, you might try this one. It has worked for many others ...
    Use iTunes to do a reset to factory default condition. Always be sure to do your backups before fiddling with your iPad. You might do both the iCloud and the iTunes backup, just to be sure!
    Back up and Restore your iOS Device with iCloud or iTunes
    http://support.apple.com/kb/ht1766
    iTunes: About iOS Backups
    http://support.apple.com/kb/ht4946
    Use iTunes to Restore your iOS Device to Factory Settings
    http://support.apple.com/kb/ht1414
    Various issues from many different users have been solved by this. I've lost count on how many have been helped by this, so far. But, it doesn't mean EVERYONE will be helped, but I've seen a whole lot. You can only try and see ...
    iPad 2 and iOS 8.0.2 Problems
    For all iPad 2 owners, this is an important solution for you! These problems result from long-term use, continuous upgrades, corrupted files and various glitches that happen over this long term use. You just need to get your iPad 2 back to FACTORY FRESH CONDITION to start out clean!
    Here's one person's solution which will help a lot of iPad 2 users!
    keithfrommariettaOct 12, 2014 3:25 PM Re: IPAD2 very slow after IOS 8 upgrade
    Re: IPAD2 very slow after IOS 8 upgradein response to pacoKAS
    SOLVED:  IOS 8 Issues on iPad 2:
    I just returned home from a visit to the Genius Bar. Like you and many others, when I upgraded my iPad 2 to IOS 8, it became practically unusable. It was VERY slow, lagged whenever trying to to do anything. Lots of screen freezes and apps spontaneously crashing. I was convinced that the processor on the iPad 2 just couldn't handle the new IOS and I went in to see about restoring to IOS 7.
    Thankfully, I was hooked up with a very sharp guy at the bar. The problem is not with the OS, it is with it being an *upgraded* OS. He used the analogy of when you had an older Windows computer and how over time (and over upgrades), they just tended to get slower and slower because of all of the garbage that was carried forward in the upgrades. At those times (and if you've ever had a Windows computer, you get this), the only thing that would speed it up would be to wipe the machine and do a fresh install of the current OS and then reload your apps, and the viola, everything would be fast again. Well, it turns out that IOS can suffer the same problems.
    THE FIX:  FIRST, be sure you have a current iCloud backup of your device.  Connect your iPad to a computer that has a clean fresh copy of IOS 8 on iTunes (this is best done with a computer other than the one that you sync your device to because you DO NOT want to restore it from a back up just yet). Ideally, if you do this at an Apple store you'll be assured of the right version there and someone to answer any questions you might have along the way. You then hold the power and home button down to hard-reset the device and continue to hold them down until it reboots into recovery mode. You then follow the instructions on the computer to reinstall the OS on the device (which wipes everything from it and then reinstalls a clean copy of it). Once this is done (which only takes about 15 minutes), your device will reboot and ask you to set it up. Answer the questions about language, location, etc. and continue until it asks you to log into your iTunes account. Once you do that, it will ask if you want to either 1) Set it up as a new device, 2) Restore from iCloud, or 3) Restore from iTunes. Choose (2), restore from iCloud. This will ensure that it brings down "clean" copies of all of your apps and preferences rather than the potentially corrupted ones that might reside in your iTunes backup. That's it! It will take a few hours depending on how much data and apps you have, but I am happy to report that my iPad 2 is now running IOS 8 and it's running as fast as it ever did when it was brand new!
    To sum it up, this process 1) Wipes your device and the garbage causing your problems, 2) Loads a clean and bug-free version of IOS 8 to your device, and 3) restores your apps and data so that it looks just like it did before the wipe, with the exception that it works now!  :-)
    Note also that by following this process you don't have to go through the painful and laborious process of reloading all of your apps, data and/or settings. iCloud takes care of all of that for you.

  • Can Motion 5 replace a green screen and blue screen in the same shot?

    Can Motion 5 replace a green screen and blue screen in the same shot? I would like to replace a green screen with one image, and a blue screen with another.

    Fox gives a good example for keying green & blue (or any other color)  from the same shot. I'd suggest doing a few things to get better accuracy.
    First, the motion keyer always removes the color it detects the most of by default (blue/green). You can override this by setting the Strength parameter to zero, then use the Color sample tool to select the color you want. The advantage is motion will do a good job of targeting only the hue (color) that you want to remove and set an appropriate starting softness.  It also will remove spill based on this color.  Looking at Fox's example movie and the shot, I'd approach the same shot this way:
    Remove the Blue
    1. Apply the keyer and set the strength to zero.
    2. Use the Sample Color tool and select the blue (or other color) to be removed.
    3. Decrease the spill level (if needed). In Fox's example the spill from the blue glasses is going to be minimal, especially compared to the green screen, your shot may need different adjustments. Only de-spilling what you need to will give you more accurate color right away and minimize additional color correction that might be needed later.
    4. Use the Color selection tools (Chroma wheel/Luma bar) to fine tune.  Ideally you want a minimal tolerance, the inner selection, with a nice fall off, the outer selection. Try with the Scrub boxes setting first, then switch to manual if you need more control. Again see Fox's example.
    Remove Green
    It's the same as the blue, you could apply the keyed to the same clip or a parent group, at this point it's many user preference.
    With these techniques you can remove any color from a shot or create a mask based on a color. BTW, as you are learning to use the keyer I'd highly recommend  having the Color Selection open so you can see the graphs.  These give you real time feedback as you make selections and changes with the Strength, Refine and Color selection tools.  Watch what happens as you make selection or changes, sometimes the problem area is actually in the brightness not the color, or the softness may change  more than the tolerance selection.  Observing what is happening in these graphs will help you figure out wha to change and speed things up.

  • Windows 7 Screen Resolution not changing at all when I try to change settings. I ve lost my ToolBar on internet for settings ( deletion of cache) Please help me to reset screen.

    Windows 7 Screen Resolution not changing at all when I try to change settings. I ve lost my ToolBar on internet for settings ( deletion of cache) Please help me to reset screen. The screen seems to have slipped or moved to the right. Only icons on left of
    screen showing. I Need to regain The right side of the scree
    I have tried everything I know to sort this out. Thankyou you in advance. Katy Nanna x

    Hi,
    When you set your monitor to a screen resolution that it won't support, the screen will go black for a few seconds while the monitor reverts back to the original resolution.
    Regarding screen resolution, we may follow the below two articles to change it:
    Change your screen resolution
    Getting the best display on your monitor
    Follow the steps below:
    1. Open Screen Resolution by clicking the Start button, clicking
    Control Panel, and then, under Appearance and Personalization, clicking Adjust screen resolution.
    2.Click the drop-down list next to Resolution. Check for the resolution marked (recommended). This is your LCD monitor's native resolution—usually the highest resolution your monitor can support.
    And if the monitor is LCD monitor, The monitor's  manufacturer or reseller should also be able to tell you the native resolution for your LCD monitor.  Or we may check the monitor's manual to adjust.
    Best regards
    Michael Shao
    TechNet Community Support

  • Grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced 6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen

    grey screen no apple followed by blue screen with vertical lines. Graphics and logic board replaced <6 months ago. What to do? I held down shift, it gets HOT HOT and makes noises. (for safety mode) followed by a blank grey screen and blue screen. Then tried the other way (sorry, I think  it's command alt delete? I don't remember) and it turned from grey (no apple symbol) to blue blank. Then third time, grey followed by blue with vertical lines, not blocky clear lines that you can see if you are close to it.
    Thanks for any help!

    You have to take the computer to the Apple store to have it checked out.
    Genius Bar reservation
    http://www.apple.com/retail/geniusbar/
    Best.

  • I am getting frequent lock-ups and blue screens during boot up. The lock ups occur during normal use and I cannot click anything or force quit. The cursor shows something is loading, but never stops. I have to use power button. Ideas?

    I am getting frequent lock-ups and blue screens during boot up on my Mac Pro.  The lock- ups occur sometimes during normal use and I cannot click anything or force quit. The cursor shows something is loading, but never stops. I have to use power button.
    I had the Mac Defender malware and I have used apple jack but still having issues.

    I am getting frequent lock-ups and blue screens during boot up on my Mac Pro.  The lock- ups occur sometimes during normal use and I cannot click anything or force quit. The cursor shows something is loading, but never stops. I have to use power button.
    I had the Mac Defender malware and I have used apple jack but still having issues.

  • Help....I am trying to set up iClould on my pc....the set up was complete....when I try to sign in to set up it says the Apple ID is valid but is not an iCloud account.  Please help me and tell me what I am doing wrong.

    Help....I am trying to set up iClould on my pc....the set up was complete....when I try to sign in to set up it says the Apple ID is valid but is not an iCloud account.  Please help me and tell me what I am doing wrong. Thx

    Hi DesCoop,
    You must initiallly activate iCloud from an IOS device or a Mac. You cannot inititally activated from a PC.
    Sorry.
    GB

  • I just want to ask if there is any way i can fix my ipod touch 4G from watar damage and i dont think that a larg amount of water have entered and the ipod isnt working at all and i tried charging it but it didnt work so please help me, and thankyou.

    I just want to ask if there is any way i can fix my ipod touch 4G from watar damage and i dont think that a larg amount of water have entered and the ipod isnt working at all and i tried charging it but it didnt work so please help me, and thankyou.

    Probably dead if you have tried to charge it.
    You should never try to charge or turn on a wet electronic device.
    You should let it dry for  a week or so, then try.

  • HT5312 I forget answer to my qustion with rescue email adrees please help me and send the answer to my main mail. Thank you very much

    I forget answer to my qustion with rescue email adrees please help me and send the answer to my main mail. Thank you very much

    We are fellow users here on these forums, you're not talking to iTunes Support.
    If you don't have access to your rescue email account, or you don't have one on your iTunes account, then you will need to contact iTunes Support / Apple to get the questions reset.
    Contacting Apple about account security : http://support.apple.com/kb/HT5699
    When they've been reset you can then use the steps half-way down this page to add/change a rescue email address for potential future use : http://support.apple.com/kb/HT5312

  • Can anyone help me with blue screen while updating to ios8?

    help me with blue screen while updating to io8.2

    I don't have a 4G device, but I thought you can use mobile safari, the safari on the iPad, on 4G.
    You could also try looking for a third party app. The official facebook app has been non to barely functional for years. I use mobile safari on my iPad although I do have a couple  of apps I've used upon occasion.

  • Cropping and Blue Screening - 2 unrelated questions.

    1) When I straighten a still in Canvas by using the wire frame, to make a house level, say, the cropping lines, naturally, move with it. So a cropping line at an angle will give me a slanting top and bottom line. So how can I crop it so that the picture has a square aspect? Is the only recourse to go back to the original site for the picture, GIMP or iPhoto, perhaps, crop it there and re-import the photo into FCE? Or is there a quicker way?
    2) I have added a number of videos above my main video to show, for example, falling snow, and eliminated their black background by Modify - Composite Mode - Screen. Very easy and by no means unusual. So, my question, is, why all the fuss about green and blue screening? Setting it up seems troublesome. A black background for the purpose is much easier to make, and, for that matter, easier to find. I looked down my back yard this morning and this side of the creek are jet black bushes which would seem ideal for such a purpose. This seems such a no-brainer that I think I must be missing something. But it is curious.
    Allosaurus

    1) I shall immediately turn to the garbage matte section in your book - I'm sure I remember seeing one - and work it out from there. And here I always thought a garbage matte was that rug I bought in Cairo.
    2) A black screen. That does give me a thought. When I return to my upcoming masterpiece, " "Orrible Murder at the Castle Doom" I could put one of my granddaughters in a black suit, photograph her against a black background and Voila! a floating head. I wonder if they give out Oscars for original ideas?
    Once more. Thank you.
    Allosaurus

  • I lost my iPhone 3 days ago.. it wasn't connet to internet and I don't know how find it without the connection.. please help me and give me some advices!!

    I lost my iPhone 3 days ago.. it wasn't connet to internet and I don't know how find it without the connection.. please help me and give me some advices!!

    Change your passwords.

Maybe you are looking for

  • Simple Java question about releasing beans from memory

    Hi, I use many beans in my app. Is there a way to release them from memory, or destroy the object. I feel that its possibly eating my memory up over time. Most of my beans are in page scope. Some are in session scope. So the page scope ones should ki

  • Photoshop CS6 sign in required not working

    the username/password is correct. it just will not proceed....

  • How to expand multi-line fields in pdf forms?

    I have a FormsCentral PDF form, which allows users to fill out the form and save as a PDF. However, after receiving the completed forms, I am unable to see all the text in the multi-line field boxes without opening them and scrolling down. Since I wi

  • Can I turn off iMessage for one contact?

    My wife recently switched from the iPhone 4 to a Galaxy S3, and in order to be able to send her a text message, I have to turn off iMessage. Is there any way to turn it off for an individual contact instead of turning it off completely? Or can I tell

  • Itunes store to iphone 3G

    hey i have a question, when i buy an app from the itunes store how do i get it onto my iphone 3G??