Ports Required for SCCM Distribution point

Hi All,
Can anybody tell me the ports required for distribution point. as in I have a site server with distribution point in HO, i want to have a distribution point server on a remote site. i went through the microsoft document which says u require port 445 open between site server and distribution point and it says u only require port 80 or 443 open between distribution point and branch distribution point. little confused!!!. which ports i require to be open between site server with distribution and remote site distribution point.
Cheers.

Hi,
Regarding the doc here:
http://technet.microsoft.com/en-us/library/bb632618.aspx
Site Server -- > Distribution Point
SMB 445 TCP
RPC Endpoint Mapper 135 UDP and TCP
RPC dynamic TCP
Site Server < -- > Site Server
SMB 445 TCP
Point to Point Tunneling Protocal (PPTP) 1723 TCP
Follow me through my blog and Twitter!

Similar Messages

  • Ports Required for SCCM 2012 Distribution point

    I think below are the port need to open for distribution point instalaltion
    Site Server -- > Distribution Point
    SMB 445 TCP
    RPC Endpoint Mapper 135 UDP and TCP
    RPC dynamic TCP
    my question here is for install Distribution point instalaltion , only
    Site Server -- > Distribution Point one way port open  is enough? or do we need to open both ways?

    One way is enough for a standard Distribution Point. All distribution is initiated by your Primary site server by the Package Transfer Manager.
    Regards,
    Nickolaj Andersen | www.scconfigmgr.com | @Nickolaja

  • What are the ports required for the Audio, Video and A/V conferencing when the following end points are enabled for QoS in Lync 2013 server?

    Hi All,
    What are the ports required for the Audio, Video and A/V conferencing when the following clients are enabled for QoS in Lync 2013 server?
    Client Type
    Port range  and Protocol required for Audio
    Port range and Protocol required for
    Video
    Port range and Protocol required for
    A/Vconferencing
    Windows Desktop   Client
    Windows mobile App
    Iphone
    Ipad
    Andriod phone
    Andriod Tablet
    MAC desktop client
    Please advise. Many Thanks.

    Out of the box, 1024-65535 for all of the client ports.  :) 
    https://technet.microsoft.com/en-us/library/gg398833.aspx
    You'll want to tune your client ports a bit
    https://technet.microsoft.com/en-us/library/jj204760.aspx as seen here, and then the client ports would use those ranges which is easier to set QoS markings.  I'm not sure the mobile clients respect that setting.
    Elan's got the best writeup for Windows clients here:
    http://www.shudnow.net/2013/02/16/enabling-qos-for-lync-server-2013-and-various-clients-part-1/
    However, the marking of the packets is the tricky part.  Windows can do it via Group Policy, but for the other clients you'll need to have the network specifically prioritize ports regardless of DSCP markings.  You have to do it based on ports
    as the traffic could be peer to peer.
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
    SWC Unified Communications
    This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

  • Ports required for voice gateway registration

    Hi,
    Currently our remote office voice gateway is trying to register to the CM and in between there is a firewall. We have opened port DNS, NTP, 2427 and 2428 but it still showing registering to the call manager. What other ports shall we open to make it works?
    What about the port requirement for CUE?
    Thanks.

    For MGCP:
    DNS
    NTP
    UDP 2427
    TCP 2428
    TFTP (UDP 69)
    For CUE, here is a link you may find helpful:
    http://www.cisco.com/en/US/partner/netsol/ns340/ns394/ns165/ns391/networking_solutions_design_guidance09186a00801f8e31.html#wp41149
    hth,
    nick

  • Port required for Veritas cluster implementation

    hello there ,
    i need to know what are the port required for veritas cluster implementation on Sun Messaging Server 6.2 . anybody care to help me on this ?
    thanks

    > We are planning a 2 node Oracle 9i RAC cluster on Sun
    Cluster 3.Good. This is a popular configuration.
    Can you please explain these 2 questions?
    1)
    If we have a hardware disk array RAID controller with
    LUNs etc, then why do we need to have Veritas Volume
    Manager (VxVM) if all the LUNS are configured at a
    hardware level?VxVM is not required to run RAC. VxVM has an option (separately
    licensable) which is specifically designed for OPS/RAC. But if
    you have a highly reliable, multi-pathed, hardware RAID platform,
    you are not required to have VxVM.
    2)
    Do we need to have VxFS? All our Oracle database
    files will be on raw partitions.No.
    IMHO, simplify is a good philosophy. Adding more software
    and layers into a highly available design will tend to reduce
    the availability. So, if you are going for maximum availabiliity,
    you will want to avoid over-complicating the design. KISS.
    In the case of RAC, or Oracle in general, many people do use
    raw and Oracle has the ability to manage data in raw devices
    pretty well. Oracle 10g further improves along these lines.
    A tenet in the design of highly available systems is to keep
    the data management as close to the application as possible.
    Oracle, and especially 10g, are following this tenet. The only
    danger here is that they could try to get too clever, and end up
    following policies which are suboptimal as the underlying
    technologies change. But even in this case, the policy is
    coming from the application rather than the supporting platform.
    -- richard

  • Ports Required for SMTP access from DMZ

    We have a Windows 2000 Adv Server on a DMZ interface of a PIX firewall. We are using native Windows SMTP services as a Front End server for Exchange mail. Our Exchange server has a SmartHost entry that sends outbound mail to the server on the DMZ. Our MX record points to the server on the DMZ for inbound traffic.
    We originally allowed DNS resolution and SMTP (Port 25) traffic to the server. We've done this numerous times from the Internal interface of the PIX. Yet, there apparently is at least one other port that needs to be opened up because the mail stays in the Queue of the SMTP server on the DMZ. We got around the problem by opening up all outbound ports from that server.
    My question is: "Does anyone know what ports are required for an SMTP server to work on a PIX DMZ?"
    Thanks

    Should just be TCP/25 and probably DNS (UDP/53). Probably the easiest way to figure out what other port it's using is to look at the active connections from this going through your PIX.
    Let's say the IP address of the mail server is 10.1.1.1. Doing:
    sho conn | include 10.1.1.1
    will give you all the connections. This will tell you where it's connectig to and on what ports. The output will look something like:
    FW1(config)# sho conn | incl 10.1.1.1
    UDP out 10.2.2.1:17127 in 10.1.1.1:10655 idle 0:01:23 Bytes 1000
    UDP out 10.2.2.1:18733 in 10.1.1.1:10477 idle 0:01:38 Bytes 1000
    UDP out 10.3.3.2:18429 in 10.1.1.1:10789 idle 0:01:10 Bytes 1000
    The numbers after the colons are the port numbers on the connection. Of course yours will show TCP and port 25 (and something else hopefully), but you get the idea.

  • Ports required for Flash Player?

    What ports are required to be open by Flash Player 10 Active X?

    Hi,
    Regarding the doc here:
    http://technet.microsoft.com/en-us/library/bb632618.aspx
    Site Server -- > Distribution Point
    SMB 445 TCP
    RPC Endpoint Mapper 135 UDP and TCP
    RPC dynamic TCP
    Site Server < -- > Site Server
    SMB 445 TCP
    Point to Point Tunneling Protocal (PPTP) 1723 TCP
    Follow me through my blog and Twitter!

  • Ports required for GG setup (Oracle to Oracle replication )

    GG version: 11.2.1.0.1
    OS : RHEL 5.4
    We are going to configure GoldgenGate which is going to replicate the DMLs for few tables (Uni-directonal) from source to target.
    Since there is a firewall between source and target, We need to request the network team to open ports at both source and target servers.
    For manager process , we are going to use the default 7809 both at source and Target. What are the other ports that we need to request the network team to open for both servers ?

    Hi,
    If a firewall is being used at an Oracle GoldenGate target location, additional ports are required on the target system to receive dynamic TCP/IP communications from remote
    Oracle GoldenGate processes. These ports are:
    ● One port for each Collector process that is started by the local Manager to receive propagated transaction data from remote online Extract processes. When an Extract
    process sends data to a target, the Manager on the target starts a dedicated Collector process.
    ● One port for each Replicat process that is started by the local Manager as part of a remote task. A remote task is used for initial loads and is specified with the RMTTASK
    parameter. This port is used to receive incoming requests from the remote Extract process.
    ● Some extra ports in case they are needed for expansion of the local Oracle GoldenGate configuration.
    ● Ports for the other Oracle GoldenGate products if they interact with the local Oracle GoldenGate instance, as stated in the documentation of those products.
    To specify these ports, use the DYNAMICPORTLIST parameter in the Manager parameter file.
    Follow these guidelines:
    ● You can specify up to 5000 ports in any combination of the following formats:
    7830, 7833, 7835
    7830-7835
    7830-7835, 7839
    ● The ports must be unreserved and unrestricted.
    ● Each Manager instance on a system must use a different port list..
    Although not a required parameter, DYNAMICPORTLIST is strongly recommended for best performance. The Collector process is responsible for finding and binding to an available
    port, and having a known list of qualified ports speeds this process. In the absence of DYNAMICPORTLIST (or if not enough ports are specified with it), Collector tries to use port 7840 for remote requests. If 7840 is not available, Collector increments by one until it finds an available port. This can delay the acceptance of the remote request. If Collector runs out of ports in the DYNAMICPORTLIST list, the following occurs:
    ● Manager reports an error in its process report and in the Oracle GoldenGate ggserr log.
    ● Collector retries based on the rules in the Oracle GoldenGate tcperrs file
    For more information about PORT and DYNAMICPORTLIST, see the Oracle GoldenGate Windows and UNIX Reference Guide.
    Hopefully this will help you
    Annamalai.

  • Firewall Ports Required for NAC manager to manage/add Cisco switch

    Hi,
    I am trying to add cisco switches to the NAM, however i am not able to add the switch as I am getting the error "unable to control switch" I have tried to open ports 161-162 on the firwall; if i was to allow any traffic between the NAM and switch, the cisco NAM is able to add/manage the switch.
    Not sure what other ports may be required for cisco NAM to manage the switch?
    Thanks.

    Hi,
    AFAIK, only the UDP ports 161-162 for the SNMP communication need to be open.
    Please make sure you have configured the correct port on the switch:
    (config)# snmp-server host 172.16.1.61 traps version 2c cam_v2 udp-port 162 mac-notification snmp
    If still not working i would check the logs on the firewall for any blocked traffic between the CAM and the switch.
    HTH,
    Tiago
    If  this helps you and/or  answers your question please mark the question  as "answered" and/or rate  it, so other users can easily find it.

  • Ports required for Goldengate Setup 7809......

    hi,
    i am using default port 7809 on my server.we have also firewall. we have just open only one port.i.e 7809 Telnet srev2 7809... connected
    but problem in data pump process, can't be establish the Network connection with remote server.
    So is there any other ports that should be open on Source & Target server as well.
    Regards,
    AMSII

    1.Paste your source and target mgr.prm and data pump paramater files entries.
    2. What is the exact error message in report file?
    3. Did you open port for source system as well as target systems?
    for more details ,
    Assigning Manager a port for local communication
    The Manager process in each Oracle GoldenGate installation requires a dedicated port for communication between itself and other local Oracle GoldenGate processes. To specify this
    port, use the PORT parameter in the Manager parameter file. Follow these guidelines:
    1. The default port number for Manager is 7809. You must specify either the default port number (recommended, if available) or a different one of your choice.
    2. The port must be unreserved and unrestricted.
    3. Each Manager instance on a system must use a different port number.
    Use the DYNAMICPORTLIST parameter to specify a list of available ports to which the following,
    local Oracle GoldenGate processes can bind for communication with a remote Oracle GoldenGate process:
    ● Collector: to communicate with a remote Extract to receive incoming data.
    ● Replicat: to communicate with a remote Extract to receive data during an initial load task.
    ● Passive Extract: to communicate with a remote Collector
    ● GGSCI: to issue remote commands
    Hopefully this will help you
    Annamalai.

  • Ports required for communication between Web servers and service applications (the default is HTTP)

    We're using SharePoint 2010, I'm the system admin for a SharePoint farm. We enabled SharePoint Search by adding a Search Service APplication. One of the crawl report timer job is failing every 5 minte with the error "Cannot connect to remote server".
    After digging around, we found that the server running the timer job tries to connect to the SearchAdmin.svc on the index server, over HTTPS / port 32844 However, communication over SSL via a non default port is blocked by our firewall.
    According to this article: https://technet.microsoft.com/en-us/library/cc262849.aspx the default is HTTP for communication
    between web servers. How is it possible that it's trying to connect over SSL?

    Hi,
    Quoted from
    https://technet.microsoft.com/en-us/library/cc262849.aspx#ServiceApp :
    You can change the protocol and port binding for each service application. On the Service Applications page in Central Administration, select the service application, and then click
    Publish.
    Here is an article for configuring Windows firewall port rules for SharePoint using PowerShell in case you need:
    http://www.xylos.com/default.aspx?id=1050
    Regards,
    Rebecca Tu
    TechNet Community Support
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • SCCM Distribution Point Failures

    I have 16 DP's in Config manager all were working last week. Now only 2 are allowing content. The error message states:
    Possible cause: Distribution Manager does not have sufficient rights to the computer.
    Solution: Verify that the site server computer account is an admin on the distribution point computer.
    I have done all this. As I stated they were all working last week No permission changes have been made. I am stumped.
    J. Mink

    Please add details about the issue. Are you talking about distributing content to DPs? Or that clients cannot download content? 
    Also the log above does not look like it's distmgr.log. "DISM" in distmgr.log does not look familiar to me. Please add some more lines. 
    Torsten Meringer | http://www.mssccmfaq.de

  • Ports required for VPN (L2TP)?

    I am having problems getting my VPN (L2TP) working. I have opened up port 1701, do any other ports have to be opened up for the VPN to work?
    Thanks
    Tony

    4500/udp (ipsec) and 500/udp (isakmp) as well. You also need to open Protocol ESP on your firewall. If you travel past a NAT router that one needs to be capable of IPsec as well.
    MacLemon

  • Port required for DNS Integrated Zone replication

    Hi All,
    A segment of the network is secured through a firewall, inside this segment I have a Windows 2012R2 DNS Server that hosts also Active Directory integrated zones, what ports should I allow so that the DNS server can replicate the DNS zone from and to the
    main network?
    I read this https://technet.microsoft.com/en-us/library/dd772723%28WS.10%29.aspx?f=255&MSPPError=-2147217396
    but I would like to limit the port to the minimum

    Hello,
    you wrote "inside this segment I have a Windows 2012 R2 DNS Server that also hosts AD integrated zones"
    So this server is a domain controller.
    Best regards
    Meinolf Weber
    MVP, MCP, MCTS
    Microsoft MVP - Directory Services
    My Blog: http://blogs.msmvps.com/MWeber
    Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
    Twitter:  

  • Distribution Point

    Hello,
    One server Distribution Point died this morning.
    1. Is it possible to disable temporarily (thinking the new server will use the same name and IP ) the distribution Point for this site? Or should I delete it?
    2. What are the requirements for a Distribution Point Server? Documentation?
    SCCM 2007 R3 - 2,000 Clients
    Thanks,
    Dom
    System Center Operations Manager 2007 / System Center Configuration Manager 2007 R2 / Forefront Client Security / Forefront Identity Manager

    Removing DP :
    http://technet.microsoft.com/en-us/library/bb680873.aspx
    Requirements :
    http://technet.microsoft.com/en-us/library/gg712321.aspx
    http://technet.microsoft.com/en-us/library/bb680614.aspx
    Arnav Sharma | Facebook |
    Twitter Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members
    reading the thread.

Maybe you are looking for