Power button not functioning well

 van any one give solution tothis problem.  my laptop show blank screen although led lights are on in batery. with external power also fisrt pres same thning happen but upon hard reset and putting on again it starts normally. waht is the problem and solution to this problem. nay on please help me

Amazing how people areover reacting... think guys for god sake! Why do you think the button doesnt click? yeah right!!! because there is rubber under it! Why? to make the device waterproof.
Offcourse it doesnt make the sound or give the same feedback a button gives on a not waterproof smartphone. 
One advise if you really hate it. and i do too because it feals like the button will stop working any minute. you enable the double tap function on the screen to wake the device. If you install Lock screen by Go launcher EX you can put a button on the homescreen to shutdown the screen. This way you wil never have to press the power button except when you need to reboot or power down the device.

Similar Messages

  • Cinema Display Power Button Not Functional

    The power button on my cinema display does nothing when pressed. The other button on the display (display preferences button) does work as expected. I have confirmed that the 'Disable power button' is not selected in the display settings panel.
    The button glows brighter when I press it, but nothing else happens.
    I would like to be able to start up and shut down my computer with this button since my bluetooth keyboard cannot do it, and I keep my laptop shut when it is connected to the external display.
    I was just given this display, so I do not know if has ever worked.
    Any ideas?

    Hi Ron,
    Possibly a daft question but do have either of the Cinema Display's USB or firewire cables plugged into your G4 as well as the DVI connection? This may sound obvious but I couldn't get the buttons on my 20" ACD to work until I plugged the USB connection into my Macbook.

  • Power button not functioning

    My power button doesn't respond whenever I click it. Instead, the volume up button does so.

    Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
    Are there not any reaction at all if you press and/or hold the ON/OFF button down? If not, it sounds more related to a hardware problem that a technician at an authorized service center needs to examine and fix.
    Thereby, I suggest that you visit nearest service center to have the phone examined by a technician. You can contact your local support team for further information about nearest service center and/or how to proceed with this in the best possible way:
    http://www.sonymobile.com/global-en/support/contact-us/contact-info/
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Bbz10 power button not function

    I own bbz10 nearly 2 months now, but since last week power button started not responsed, I tried to restore about 3 times already, same things keep occured. Need solution desperately. Thx

    If you tried to restore your phone, and by that I assume you mean either battery pulls and/or factory reset, and it still doesn't work, it sounds like a hardware issue for which you would have to talk to T-Mobile.  We can only advise on software issues here, we can't fix anything related to hardware.
    I hope that helps you.  
    - If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

  • Power button not working properly for iphone 5. Warranty expired on 22 nov 2013 what to do?

    Hi,
    Power button not functioning properly for my iphone 5. Kindly give advice on what to do. Its warranty expired on 22nd november 2013.

    Read here:
    https://ssl.apple.com/support/iphone5-sleepwakebutton/

  • I just restored my ipod and the power button works, as well as the home button but when I slide the unlock button it doesn't respond. Basically it is not sensing that I am touching it. I've tried restoring it and restarting it but nothing seems to work.

    I just restored my ipod and the power button works, as well as the home button but when I slide the unlock button it doesn't respond. Basically it is not sensing that I am touching it and I can not get out of the home screen. I've tried restoring it and restarting it but nothing seems to work. I've tried everything, is there anything I can do myself to fix it?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Iphone 5 power button not working!! They have replacement program for months but why they dont email you and say it??

    I have had iphone 5 and have never been happy and i think apple is not leading the technology and future of market anymore as they are lowering quality of their products(even hardware). I had to change first iphone 5 i had because of wireless issues and then i had battery problem  and had to charge 3 times a day and finally after 2 years i bought they decided that its faulty and they decide to change it. Luckily enough i read it on an online tech magazine and after googling i see that they have had replacement for power button as well which i am eligible for as well!! i go to genius bar and they replace battery but they dont replace power button cause they examine it and passes till the audio dock test! It connects to charder dock or cable but it doest to audio test dock and he says one off the pins inside is not right but it charges perfectly with every cable in the store!! And i tell him that they have to change power button not the charging pin cause it doesnt make sense!! Its a faulty product and maybe if they emailed and said it nearly a year ago my pin was right then!!  so i think they found a silly reason not to change it and so i am struggling with that phone and brand  that i hate(once i used to love)!

    ahmetfromlondon63 wrote
    And I don't know what these guys are talking about? I have an unsolved hardware issue and I posted here!
    This is a user-to-user technical support forum. This is not AppleCare. You are not addressing Apple here. No one here can help you resolve your customer service issue with Apple. Use the Contact Us link at the bottom right of every page for information on how to contact Apple directly. When you talk to them, I'd suggest not using profanity. It makes people less likely to help you.

  • Exit button not functioning in MSS Team - Recruiting - Create new Candidate

    Hello Experts,
    Exit button not functioning in MSS Team - Recruiting - Create new Candidate Assessment iview
    Location of exit button :Create new Candidate Assessment iview we have next button when we click on we can see exit button in next iview
    any idea why it not functioning / help on this / or is it a bug from SAP
    Thanks,
    Regards
    Vijay

    Hi Krishore,
    Thanks for reply,
    The version of BP_ERP5ESS is 1.0 SP8 and The version of SAP_ESS is  600 SP8.
    do need to add extra patch for this.
    please help me on this issue. 
    Thanks,
    Regards
    Vijai

  • Power button not working

    iPopd touch 4th generation sleep/power button not working.
    Any ideas? how long is warranty?

    The standard warranty is one-year. Yu can purchase, before the one-year is up and additional year. Yu can check your coverage here:
    Apple - Support - Check Your Service and Support Coverage
    Have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?

  • Power button not working with 7.1 update

    Power button not working with 7.1 update

    I take it your phone was still under warranty then?!
    Unfortunately I was not so lucky, and my experience was rather poor service-wise. They're called Apple Geniuses but I beg to differ...
    I'm not sure where in the world you are located, but my "experience" involved visiting the Leeds store and confusing everyone with this issue. I can tell you, just by the looks on their faces, they had never been faced with this problem before!
    I suggested my phone was rolled back to the version it was previously to establish whether this was the underlying issue. I was asked whether my phone had been backed up and as it had the "genius" proceeded to restore the phone "as it came out of the factory" to quote him.
    When this was completed the phone was still doing the same thing and I was advised "the software update must have highlighted a hardware issue." I was told it would have to be physically repaired and was told to have this done by a third party as Apple would charge approximately £160. Incidentally, I work in IT and repair PC's, laptops and mobile devices for a living and made a point of raising that a sleep/wake button ribbon cable for an iPhone 4S can be bought on eBay for as little as £3.00...if indeed it does need replacing, which I suspect it does not.
    Anyway, so now I was left with a phone for the rest of the day which was blank and still the problem remained. On the train, on the way home, you can then imagine my disbelief when I actually took the time to look at my phone's configuration and realised that iOS version 7.1 was still installed, so obviously the issue would still remain. So the visit to the "genius bar" was a complete waste of time as I'm still in the very same position, and I still blame the 7.1 update for this...let's home 7.2 is released very shortly and this solves the issue...
    I have downloaded the package to roll the version back to 7.0 but I'm a little reluctant to carry this out yet as I would expect Apple to so the issue they have caused. This is NOT hardware related but software.
    I seriously think Android is calling me...

  • T430 Bluetooth not functioning well

    I had a T430 for half year, recently the bluetooth not functioning well.
    when I try to open a connected device(mobile phone), the device control window will show up for just 2 second, then turn off. If i keep trying for a couple times, and error message will show up: "This operation failed to initialize......."
    I had been using the WII remote for a while before this happened. It still can connect new device correctly. 
    I have try uninstall the driver, 
    For that 2 second I can see the control window has correct information for the mobile phone, 
    Has anyone had the similar issue?

    yes i had something similar happen once. I tried to uninstall the bluetooth driver and reinstall the latest version of the bluetooth driver. That worked for a while, then it failed again. In the end i had to reinstall the OS from scratch, which solved the issue (i also had some other driver issues, and decided that reinstall the OS was the fastest way to resolve it).
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • HT1688 Power button not working

    Power button not working on iPhone 5

    This is a defect on iPhone 5 power button that wears out in about 13-14 months of usage just after you go out of warranty. Apple is aware of this issue but chooses not to accept this as a defect. I asked the Genius bar guy and they told me this is a common case recently and costs $269 to replace your phone. There is no repair option. I am very mad and believe Apple needs to take action or will lose their customers. All iPhone 5 owners that I know started having this problem in the month of 13 -14.
    I believe if the numbers go high, Apple may start a recall program. Please encourage anyone with this problem to post here. $700 phone should not wear out this soon. Apparently the part is defective on almost all iPhone 5 devices.
    Other threads about this:
    https://discussions.apple.com/message/23797113#23797113
    https://discussions.apple.com/message/23258974#23258974

  • TS1538 iphone5 went in recovery mode after replacing power button, everything went well in the repair  ,try to restore but it quit in the middle of the process

    iphone5 went in recovery mode after replacing power button, everything went well in the repair  ,I try to restore but it quits in the middle of the process and go back to i tunes logo please help I been without my phone for a week.

    Hi
    did you get any reply?
    I have the same problem I dont know what to do..
    Regards

  • I have an iphone 4, when I upgraded to ios 7.1.1 the application 'superlive pro' is not functioning well it is stucked and some times the device needs to be restarted

    I have an iphone 4, when I upgraded to ios 7.1.1 the application 'superlive pro' is not functioning well it is stucked and some times the device needs to be restarted

    if there is a compatability between the app and newer versions of the ios then likely the developer if he/she knows about it will release an update fixing the issue
    but of cause the developer has to know about it so maybe you should inform the developer about the issue and wait for a fix

  • :( Multi Touch Pad Not Functioning Well.

    +*I'm using 15 inch MacBook Pro which i purchase on June 2008, Ok here is my problem that I'm facing, lately my multi touch pad not functioning well it can be use only on safari other then that it unable to use at any-other folders or places. Like normally I'm able large the picture by using the multi touch pad but now i can only use it on safari to larger the font size. Do i need to update my Multi Touch Pad? What do i have to do? Please help...*+

    Hello @LouisTONG,
    Welcome to the HP Forums.
    It appears that you're tocuhpad is causing some issues. I will attempt to assist you with this.
    If this is a new notebook, make sure you've run all Windows updates and completed any updates listed in the HP Support Assistant.
    Something may address that issue.
    This may also have something that could help you: Using and Troubleshooting the TouchPad or ClickPad (Windows 8).
    If you need further assistance could you please provide the Model and Product numbers for your notebook.
    Thank you for posting on the HP Forums.
    I worked on behalf of HP.

Maybe you are looking for

  • Determine the number of records in a file

    I want to analyse record types from a large input file and so far have managed to extract different groups and created the relevant files. All I want to do now is count the number of records in each file so I can produce a report showing the differen

  • Palm Pre USB - host and client?

    I see a lot of posts about using USB Mode to transfer files between a PC and the Palm Pre, but is it possible to connect a USB hard drive or flash drive directly to the Pre to do file transfers to/from the phone?  The Palm website says that the Pre h

  • Cannot record ingame sound with glc (-git)

    I have a problem with recording ingame sound with some games with glc (well, glc-git). glc says, it can record sound from games, if they use alsa (or sdl and forcing sdl to use alsa). As long as I don't use pulseaudio, this shouldn't be a problem. Bu

  • Output not printing correctly for BI Publisher report.

    Hi All, We have a BI Publisher report which is printing correctly on one printer but not on another printer. The top and right side of the output are getting truncated. Printer type for both the printer is same that is "--PASTA Universal Printer Type

  • RVS 4000 Email responses that need addressing

    I have been bounced around between Cisco and Linksys for months-. I have two simple questions- One I know the answer on- the second, I haven't a clue- I have corresponded with 12-15 people at Linksys, and Cisco- Their last answer is I should contact