Printer will no longer print PDF document--"no pages selected" although specific pages were selected?

Brother printer will no longer print PDF document--"no pages selected" although I did specify pages.  Have reviewed and tried Adobe trouble shooting, not helpful.  Cannot print page as image.  Brother says to contact Adobe

There may be some security issues related to the USPS PDFs.
http://www.certified-mail-envelopes.com/signatures-usps-certified-mail-return-receipt-requested
I can't help with the scan/print problem. You seem to have done everything I would try.
I don't know if maybe using a registry cleaner would help.
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

Similar Messages

  • MY HP DESKJET 697C PRINTER WILL NO LONGER PRINT???? - HELP!!!!!

    My HP DeskJet 697C Printer will no longer print!?
    1.  First, a mechanical bang noise comes from inside the printer.
    2.  Next,  the top over the "ON" switch yellow light blinks!
    3.  Finally, the following on screen Error Mesage reads:
    "Your HP DeskJet 697C Printer has Failed to Print!"
    No reason is Given!
    But I suspect, something inside the printer has malfunctioned since there is a one singular "Bang" Noise
    each time I attempt to make a Print!..As if the sliding on the chrome rail ink cartridge was obstructed by something blocking its full back and forth movement during the printing process!?
    HELP!
    DFIX9
    9-12-11
    2:40 pm.

    Try resetting the printing system.
    OS X Mavericks: Reset the printing system
    If you have the printers IP address open Terminal (applications/Utilities) and at the prompt type: ping {printerIP}. You will get a reply or failure.
    Network Printer Troubleshooting
    HP – Wireless Printing Center
    HP – Printer Not Found During Wireless Installation

  • HPc410a printer will no longer print wirelessly

    running windows 7, works to print by eprint but no longer will print wirelessly. I hsve tried unplugging, tried deleting the printer from comp and reinstalling.  the tests show that the wireless connection is good. Not getting any error reports when trying to print it just never comes thru the printer. Desktop, ipad, laptop and Iphone all quit printing.

    Let's set a static IP address for the printer:
    - Print a Network Config Page from the front of the printer. Note the printer's IP address.
    - Type that IP address into a browser to reveal the printer's internal settings.
    - Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
    - On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
    - Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
    - Enter your router's IP (on the Network Config Page) for the gateway.
    - Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS. This is Google DNS. You can choose another external DNS if you wish.
    - Click 'Apply'.
    Now, shut down the router and printer, start the router, wait, then start the printer.
    After this you may need to redo 'Add a Printer' using the new IP address.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • My HP printer will no longer print in colour

    After upgrading to the latest OS my HP printer will not print in colour for me. I thought at first it was the printer error, but then I realised it still prints in colour for my husband's Dell. I've tried uninstalling and reinstalling the printer; updating the printer driver; looked and looked at the settings to try to find a colour setting in case I've somehow got it set to b&w - but I still can't get any colour print. Any ideas?

    It is quite a while since I've used an HP printer, MillyJ, but immediately under the "orientation" selection in the standard print dialogue is there a drop down box which provides a variety of choices including "Quality and Media"? If so, select it and make sure that "Grey Scale Printing" is not enabled. If not look through any other options offered. Strangely, the option for grey scale or black and white printing doesn't appear under the "Color" settings with quite a few printers.
    You might also want to have a look at http://ostatic.com/question/mac-leopard-printing-in-black-and-white and see if using the instructions there provide any clues to resolving the issue (essentially in reverse, as this person was actually trying to print in B&W and having trouble)
    Cheers
    Rod

  • HP Officejet 6500 Wireless will no longer print cyan

    Printer will no longer print Cyan.

    Make sure to use HP Genuine Ink Cartridges for your Printer as the use of refilled ink can the damage the Printhead which may cost a more serious problem related to your printing. First, check your ink levels, if your cyan ink seems to be empty then, replace it. If not, got to the Setup menu of your printer then look for "Tools" then select "clean printhead". This allow the printer to free the printhead from dust build-ups and any dried ink. If cleaning the printhead still doesn't fix the issue then try another Cyan ink cartridge. If replacing the cartride still doesn't solve the issue then you must take all the cartridges out including the printhead and manually clean the copper contacts of the printhead by wipping it with a soft lint free cloth. After cleaning, insert all back-in and perform another cleaning in the tools menu of your printer. Problem should be fixed after performing all that steps.
    Please click "Kudos" "Thumbs up" If this post was helpful.

  • CreatePDF Desktop Printer will no longer be available so how do I print a PDF from a scanned document????

    CreatePDF Desktop Printer will no longer be available so how do I print a PDF from a scanned document????

    Hi jwlaunch,
    This document describes some alternatives to CreatePDF Desktop printer: Adobe CreatePDF Desktop Printer is no longer available
    Please let us know if you have additional questions.
    Best,
    Sara

  • I have a macbook pro and aphotosmartD110 wireless printer.  I was told that if I install the printer software on my computer, it will no longer print wirelessly.  Is that true and how do I scan wirelessly without loading in the software?

    I have a macbook pro and a photosmart D110 printer.  I was told that if I load the software for the printer onto my mac that it will no longer print wierlessly.  Is that true and how can I scan wirelessly without loading the software? Also, can I just connect my mac to the printer with a cable and scan or do I need that software loaded onto the mac?  Thanks for all help!

    If you are running Lion then all drivers are distributed through Software Update. You do not need to install anything, other than to install the printer in System Preferences > Print & Scan. If you already added the printer while it was connected using USB, you might want to delete it and set it up again wirelessly to avoid confusion. Or, give them two distinct names e.g. "Photosmart D110 (USB)" and "Photosmart D110 (wireless)".
    All scanning functions are now performed using Preview, but you can also access the scanner through the same Print & Scan preference pane, or with Image Capture.
    This HP document may help explain how driver software is distributed now:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03079365&cc=us&dlc=en&lc=en &product=4144493&tmp_track_link=ot_search#N108

  • Ps will no longer print, Print on menu is grayed out

    Ps (CS5) will no longer print, Print on menu is grayed out
    Have found many discussions about this but no solutions that work in my case.
    I tried changing printers, did not work.
    I tried changing whether Ps or printer manages color - cannot find that setting except when the Print dialog shows up... and of course it does not show.
    For my Adobe PDF printer I tried changing various settings, nothing made a difference.
    Must I reinstall Photoshopj?

    Ps (CS5) will no longer print, Print on menu is grayed out
    Have found many discussions about this but no solutions that work in my case.
    I tried changing printers, did not work.
    I tried changing whether Ps or printer manages color - cannot find that setting except when the Print dialog shows up... and of course it does not show.
    For my Adobe PDF printer I tried changing various settings, nothing made a difference.
    Must I reinstall Photoshopj?

  • After downloading Yosemite, my HP Photosmart D110 printer will no longer work. The wireless connection is fine but says it cannot find my printer when trying to print.

    After downloading Yosemite my printer, a HP Photosmart D100 will no longer print. The wireless connection is fine, and a test page printed perfectly directly from my printer. When trying to print from my computer, it says it cannot connect or find the printer. I tried downloading the most updated software from HP website but it doesn't appear to be helping.

    Try resetting the printing system.
    OS X Mavericks: Reset the printing system
    If you have the printers IP address open Terminal (applications/Utilities) and at the prompt type: ping {printerIP}. You will get a reply or failure.
    Network Printer Troubleshooting
    HP – Wireless Printing Center
    HP – Printer Not Found During Wireless Installation

  • My HP Officejet Pro 8500 A910 will no longer print aqua.

    My HP Officejet Pro 8500 A910 will no longer print aqua.  I just tried two new cartridges and when I clean the heads, no aqua prints.  I get no error messages however.
    One possible issue: Recently I used a new HP aqua print cartridge (940XL version) that kept stalling my printer.  If my printer sat without printing for 10 minutes or more, the only way I could get it to print would be to shut down the printer and restart it.  Then, as long as I kept printing, it worked fine.  When I replaced the problematic print cartridge the printer works fine except now it won't print aqua.  Could the problematic cartridge damaged something?
    I looked at the print head and it looks fine.  What is strange is that NO AQUA INK at all shows on the print head page.
    What should I do?  Help!

    Hey @CWickstrom ,
    Thank you for taking the time to post on the HP Forums today! Hope you enjoy the experience.
    I recommend calling HP Technical Phone Support for this issue I believe you will be given options and help I can't.
    If you are in Canada or US call 800 474 6836, or you can Contact HP Worldwide.
    HP printers generally have a 1 year warranty from their purchase date, you can verify the warranty using the following link if you would like; warranty check.
    I hope this helps.
    I worked for HP.

  • Macbook Pro OSX 10.8 and Epson WF 7525 will no longer print. It did until quite recently . Now I get Filter failed and RastertoescpII when i try to print ( test sheets ok) . Have tried to to uninstall and reinstall but nothing. Any advice, please.

    Question ?
    Macbook Pro OSX 10.8 and Epson WF 7525 will no longer print.
    It did until quite recently . However now I get filter failed and RastertoescpII and pages of items when i try to print .
    Print head test sheets/head cleaning etc ok  .
    Have tried to to uninstall and reinstall but nothing.
    Any advice, please?.
    ps
    The printer deos not show up on Epsons site but i think I have the software from Apple.
    Not an ideal situation.

    Try a reset >  OS X Mountain Lion: Reset the printing system

  • With Leopard, iPhoto6 will no longer print captions in books

    Now that I've upgraded to Leopard, iPhoto6 (6.0.6) will no longer print the captions in books when I send them to my desktop printer (Epson Stylus Photo R300). It does print the titles on the front covers. For calendars, it'll print the lines but not the dates. Is there anything I can do to fix this?

    Try repairing permissions, try the latest security update, try recreating your drivers from scratch using the latest drivers on Xerox's website, try using open source drivers*, or recovering your old copy of the previous operating system from your backup and disabling Java.

  • MY PRINTER WILL NOT STOP PRINTING

    I have a brand new HP 309a wireless printer.  I am using it with a USB PORT.   I downloaded something from a PDF file and the printer will not stop printing.  I rebooted the computer, I disconnected the printer for an hour and when I turned it on it resumed   I hit the cancel button, the display reads "print cancelled" and then it reads "now printing."  When I attempt to use the printer to print something else it reads "busy."  HELP.
    This question was solved.
    View Solution.

    Hi,
    Disconnect the  USB cable and follow the below steps  to restart  the spooler service.
    Click Start (Windows logo) >> All Programs >> Accessories >>
    Right click on  Command Prompt and open it as Administrator ( choose run as administrator)
    Enter the below command in black window and hit enter key..
    net stop spooler
    That will stop the spooler service.
    Then enter the below command and hit enter key to start the spooler service
    net start spooler
    That will delete the current print comment and the  things in print queue.
    Press the widnows key and R key on the key board to open run window ( Click on Start >> Run).
    In run window  enter services.msc and click Ok.
    That will open services window.
    From there double click on the print spooler service.That will open a new window.
    Click on Stop button to stop and then click on start button to restart the spooler service.
    Make sure that startup type is : Automatic and Service status is : Started
    Click on Apply and Ok to close the services window.
    If the issue resolved,
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Saul
    Tech Support Eng.
    HP

  • Hi,how can i change the default settings on my adobe readerX1 such that it will display all my pdf files according to their individual cover pages (as cover picture thumbnails)before i click them to open and read........i really enjoyed this feature as a

    hi,how can i change the default settings on my adobe readerX1 such that it will display all my pdf files according to their individual cover pages (as cover picture thumbnails)before i click them to open and read........i really enjoyed this feature as a default settings upon installation in previous editions of adobe reader .i use a windows 8 pc now.thank

    For sideloaded content the nook pulls the metadata from ePub file itself.  I would suggest looking at a program like Sigil or Calibre that will let you edit the metadata in the book to make it appear like you want.
    For the PDF vs ePub - No, that's the way PDFs work (think of them as graphics, not text), wheres ePubs are Web Pages - so  no you can't them to behave exactly alike without converting the files.

  • Open a document and go to a specific page.

    Hello.
    Is there any way to tell the Reader that opens a document and go to a specific page?
    I want to do it from FileMaker, Mac and Windows.
    Regards..

    SOLVED:
    This YES WORKS ... in Windows, in Mac not.
    "File:C:/Documents and settings/user/directory/books/Book I.pdf#page=889"
    Is it a bug in Acrobat Reader 9 for MacOS X?
    II use a WebViewer in FileMaker Pro 9.

Maybe you are looking for

  • How do I connect my MacBook Pro to my Epson Stylus NX420?

    When I try to find local printers, mine doesn't come up.

  • Error while initiating travel form-Portal

    Hi Experts, I am facing an issue in portal - when I try to Display/Print the travel expense form-I am unable to see the PDF and the message that i get is "Error while initiating travel form". I am using EP7.0 SP17, have checked ADS configuration and

  • Unhiding folders and files

    How do I globally unhide folders and files.  For example, I want access to /Users/XXXXX/Library/Application Support/Microsoft/Office/User Templates/My Themes and I can't see /Users/XXXXX/Library/...

  • Importing a page

    I have imported a page from one application to another application int the same workspace. After importing the page it runs very slow in the new application (but all the functions works fine). Do I have to do any change after importing the file? thx,

  • I'm getting a cwinstr error after upgrading from labview 7.0 to labview 2010

    Hello  recently upgraged a PC from Labview 7.0 pro to Labview 2010 pro. Now I can not open a calibration executable we been using for a xantrex xfr power supply (unfortunately I don't have source code). The only error I get is "cwinstr-can't load pro