Problem of USB keyboard on K7N2L

HEY, I GOT MY NEW K7N2L AND FOUND OUT THAT MY MS USB KEYBOARD DOESN'T WORK. I UPDATED THE NEW 3.3 BIOS, IT DIDN'T SOLVE THE PROBLEM. I USED TO HAVE A EPOX KT133 BOARD, IT WORKED FIND WITH MY MS USB KEYBOARD. SO, SOME ONE PLEASE GIVE ME A SOLUTION.
THANKS

problem solved!!!
what i did was to move the kb to the usb port DIRECTLY under ps2 kb connector. it wasn't working when pluged to the usb under ps2 mouse. very strange problem, but good to get it work. 8)

Similar Messages

[K8N NEO3-F] Problem with USB keyboard and PS2 mouse after upgrading BIOS

Hello everyone!
I have upgraded BIOS from 1.1 to 1.4... I have Sempron 2600 (64bit) so BIOS v.1.1 did not recognise it.
The motherboard works, but after upgrading I have a small problem with my keyboard and mouse.
When I use USB keyboard my PS2 mouse doesn't work. When I connect PS2 keyboard mouse works!!!
Can you tell me what's wrong?
Thanks, bartull@
PS. Does BIOS v.1.3 recognise Sempron 64bit? Can you give me a link to it?

I think that the problem may have been caused by flashing either with liveupdate or with winflash. I had the problem when i used winflash correctly (shutting down all programs, checking all the boxes to clear bootblock and cmos) but had usb keyboard connected during flash. My suggestion is to reflash with floppy to last bios version that worked using only ps2 mouse and keyboard with the following instructions:
DOS floppy flash shall be performed with :
awfl833d.exe w7030nms.180 /py /sn /wb /cc /cd /cp /f /e
(Replace biosfilename with appropriate version for Neo1/neo2 etc , switches remain the same )
After flash is complete :
TURN OFF PSU (don't restart) wait 15 seconds
Turn on again , press the power button .
Enter BIOS and load optimized defaults (NO OTHER CHANGES) , save + exit
Boot the system again with the floppy in the drive to let the DMI pool build and update itself .
If that works, then reflash to the bios you tried before with the same procedure. Once you have stable system with ps2 keyboard and mouse working, re-enter bios and enable usb and keyboard support as a lot of bios' have it disabled by default for some strange reason.
Good luck.

Bug Report - Windows 8.0 - 6.0.1 USB arbitration causes USB keyboard driver failure

Can't find a place to submit a bug report. So here goes.
Full Error Message:
Windows cannot load the device driver for this hardware because a previous instance of the device driver is still in memory.
Problem Occurs:
Windows 8.0 x64
Vmware Player 6.0.1 build-1379776
Problem:
A USB keyboard ceases to function on the host operating system following the first host OS reboot after installing 6.0.1 on Windows 8.0. This issue does not occur with 6.0.0. The issue disappears upon uninstalling Player 6.0.1. Reinstallation allows Player to operate as expected, but issue re-appears after host OS reboot.
The issue happens immediately after host OS loads, and continues irrespective of whether VMWare Player is launched.
Looking at the keyboard drivers, the usb keyboard's driver has not loaded (see attached images). The built-in keyboard driver however reports no errors and continues to operate as usual.
Changing the USB keyboard device to that of a different manufacturer does not resolve the issue. Any USB keyboard driver appears to fail.
Work Around:
1) Launch msconfig
2) Disable VMWare USB arbitration service
3) Reboot
4) USB Keyboard works. VMWare Player continues to operate as normal, minus the ability to mount USB storage devices on the guest OS.

This issue was fixed on my PC as follows.
1) Taking ownership of the above usb*.sys files in the drivers folder
2) renaming them to usb*.sysold
3) Using Device Manager to uninstall all USB devices with the yellow warning ! next to them
4) Doing a Scan for Hardware changes via the Device Manager toolbar and then waiting a few moments whilst the USB devices are re-installed with signed drivers.
Hope this helps you....
usb drivers files in my drivers folder after the above process:
12/02/2013 04:12            19,968 usb8023.sys
21/11/2010 03:24            32,896 USBCAMD2.sys
27/11/2013 01:41            99,840 usbccgp.sys
12/07/2013 10:41           100,864 usbcir.sys
27/11/2013 01:41             7,808 usbd.sys
27/11/2013 01:41            53,248 usbehci.sys
25/03/2011 03:29            52,736 usbehci.sysold
27/11/2013 01:41           343,040 usbhub.sys
25/03/2011 03:29           343,040 usbhub.sysold
25/03/2011 03:29            25,600 usbohci.sys
27/11/2013 01:41           325,120 usbport.sys
25/03/2011 03:29           325,120 usbport.sysold
14/07/2009 00:38            25,088 usbprint.sysold
11/03/2011 04:37            91,648 USBSTOR.SYS
25/03/2011 03:29            30,720 usbuhci.sys
21/11/2010 03:23           184,960 usbvideo.sys
              19 File(s)      2,783,104 bytes
The .sysold files are the ones I renamed, I think also renamed the usbccgp.sys - but accidentally deleted it after the rename..

Z68A-GD65 G3 / Tesoro Durandal G1NL (USB Keyboard) problems

Hi all.
I got some Problems with my new Tesoro Durandal G1NL USB-Keyboard.
1. I cant access the Bios (UEFI)
2. I cant use the Windows bootfunctions (F8)
In Windows 7 x64 everything is OK, but it seems the KB doesnt get detected by UEFI fast enough, maybe.
I got a 2600K (Sandybridge) CPU mounted, also I'm on 23.7 Bios (ME7)
Can someone help me?
Kind regards, Chris.

Flash to the latest beta bios and retry: https://forum-en.msi.com/index.php?topic=163866.msg1213416#msg1213416
For this update you must >>use the MSI HQ Forum USB flasher<< => Mode 1: Point to archive file!
Former problems with ME8 and Sandy Bridge are no issue with current versions.

USB keyboard problems in Entourage

I have an iMac late 2013 (Yosemite) and my USB keyboard is not working in Entourage. All the other programs are fine, so there is nothing wrong with the keyboard. Can anybody help?

I use a ps2 adaptor on my usb keyboard because of the problem I have with trying to get to bios. My computer loads so fast that the keyboard isnt lit up untill its to late too get to bios. It seems the usb port has no power till late in the game, and by useing ps2 im fired up right away. I dont know why that is. This info may not help you much, but I suspect there is something to it. The only thing else I can think of is a short term memory problem. good luck doc3128

Apple USB Keyboard with Numeric Keypad Problem

Hi,
I have a Mac Mini macOS 10.5.8
I just bought an apple USB keyboard with numerci keypad (aluminium) and am having problems
1/ If i hit @ i get <
2/ if i hit < i get @
3/ the function keys do not work : if i hit fn F11 it displays the desktop (as F11 does also), i was expecting lower volume
4/ if i hit fn F12 i get the widgets (as with F12) i was expecting higher volume
etc....
It seems my USB keyboard with numeric keypad is not recognized.
If i look at the Keyboard Visualizer (top right) it displays a keyboard that does NOT look like mine, it is smaller.
Why isn't this keyboard correctly recognized ?
Thanks
Marc

ok thanks for the tip and yes i admit i didn't see that...
but it seems a little weird to have to upgrade all the OS to Snow Leopard just to use a keyboard.
That kind of new device should be configured through a driver to download...shouldn't it ?
I presume there's no keyboard driver that can solve my problem.. ?
so you confirm that if i pay for Snow Leopard and upgrade my OS, my keyword will definitely work correctly with my Mac Mini ?
Thanks

Boot Camp problem: Windows install can't "see" USB keyboard

I just got my new iMac quad-core i5 and love it.
I tried using Boot Camp to install a copy of Windows XP, just see how it would run.
The installation went fine, until under Windows Setup I have to hit ENTER. Keep in mind, I'm using the old USB keyboard from my G5, which accepted commands up to that point; not the wireless keyboard/mouse that came with the iMac.
Nothing happens, and I have to do a hard reboot to get back out.
Any suggestions? Thanks...

Macaby wrote:
First of all, I have the new 21.5" iMac (also with the wireless keyboard). I did the "Bootcamp" gig with Windows 7 WITHOUT any trouble with the wireless keyboard. Why don't you try it with the standard wireless keyboard?
After about a day of using the wireless keyboard, I plugged in a Logitech keyboard and mouse because I use the extended features (numbers) for data entry. I've asked Santa for a Mac extended keyboard as I'm not that happy about the Logitech although it works fine on the Windows side.
I should add that I used the Magic Mouse as well installing Win 7 in BootCamp. Last night I installed the new Parallels 5.0 on my MB and like it so well that I would like to have it on my iMac as well. However, I've read that there are problems having both BootCamp and Parallels 5 on the same hard drive.

USB keyboard problem (990FXA-GD80)

Hello guys,
This problem I will describe has occured to me in two games NBA2K12 and DIRT3 so far.
During gameplay suddenly the keyboard freezes and does not respond holding the last known command. (if for example I turned right in DIRT3 it will continuously go right).
In order to solve the problem I installed a very old PS2 Microsoft keyboard and fortunatelly I do not have any problems. The USB keyboard that I use is a Microsoft Wired Keyboard 600. I have installed microsoft drivers and keyboard programs with no result. I also changed USB port, no go, also connected it to a USB3 still no go...
Have you experienced something like this? Do you have any suggestions before contacting MSI support?
Thanks in advance!
MSI-990FXA-GD80 BIOS BETA 82 (last known official beta). Windows 7 Ultimate x64,

Quote from: tavliban on 30-December-11, 19:32:40
Hello guys,
This problem I will describe has occured to me in two games NBA2K12 and DIRT3 so far.
During gameplay suddenly the keyboard freezes and does not respond holding the last known command. (if for example I turned right in DIRT3 it will continuously go right).
In order to solve the problem I installed a very old PS2 Microsoft keyboard and fortunatelly I do not have any problems. The USB keyboard that I use is a Microsoft Wired Keyboard 600. I have installed microsoft drivers and keyboard programs with no result. I also changed USB port, no go, also connected it to a USB3 still no go...
Have you experienced something like this? Do you have any suggestions before contacting MSI support?
Thanks in advance!
MSI-990FXA-GD80 BIOS BETA 82 (last known official beta). Windows 7 Ultimate x64,
i shuld test to install this driver
South Bridge Driver 33 MB 11.12 12/13/2011
http://support.amd.com/us/gpudownload/windows/Pages/raid_windows.aspx
i always update this driver then they comming with new ones

USB/Keyboard problem

I sometimes have to unplug my keyboard from my G4 PB. When I do, the machine immediately starts making a strange noise--like a hyper-fast drum roll. The curser flashes probably 10-20 times per second (or something like that).
This problem has always been with this computer regardless of the OS10 verison I am using.
The keyboard is a Macally iKey.
Anyone know how to fix it?

I'm also having troubles with my USB keyboard after periods of inactivity since upgrading to 10.5.2.
If I don't use the keyboard for awhile, it will no longer "work". If I unplug and replug-in the USB connection it will start working again. The same behavior happens on both my available USB ports.
It gets pretty annoying having to unplug/replug-in the keyboard.

U45 USB keyboard problems

I'm having an U45 which shows some serious problems with the attached Sun Type 7 USB keyboard. Every now and when (like 30s or so) whilst typing the keyboard seems to hang and then shows the typed in keys in wrong order or even duplicates the keys several timeees like tihhhs.
I already have replaced the keyboard but this didn't help at all!
$ prtdiag -v
System Configuration: Sun Microsystems sun4u Sun Ultra 45 Workstation
System clock frequency: 200 MHZ
Memory size: 4GB
==================================== CPUs ====================================
E$ CPU CPU
CPU Freq Size Implementation Mask Status Location
0 1600 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 on-line MB/0
$ uname -a
SunOS frdsol10 5.10 Generic_137137-09 sun4u sparc SUNW,A70
$ head -1 /etc/release
Solaris 10 10/08 s10s_u6wos_07b SPARC
Anyone might shed some light on thisS? Papa Google doesn't want to give me an answer...
Rgds,
Dominik
Edited by: dominikfrey on Feb 11, 2010 11:45 AM

A couple of things come to mind.
But first, are there any entries related to USB in your /ver/adm/messages file?
You need to look there.
If there has been accidental damage to the USB ports and their connections to the systemboard, you could be looking at an expensive repair. I suppose you could experiment with adding a powered USB hub in between the system and the keyboard so as to compensate for any inadequacies of where you're attaching that keyboard. It will need to be the sort of hub that has its own AC-to-DC power source and not just be a passive peripheral. (I bought one at Walmart a couple of years ago for $15.)
However what I actually suspect is that your system is far down-rev on its OBP firmware level. There are a [number of USB related issues from 2006|http://sunsolve.sun.com/search/advsearch.do?collection=PATCH&type=collections&queryKey5=124409&toDocument=yes] noted in the README files of the older OBP patches.
Those OBP patches are cumulative, so if you just [get the latest one|http://sunsolve.sun.com/search/advsearch.do?collection=PATCH&type=collections&queryKey5=142703&toDocument=yes] you will have all the previous ones rolled into it.

K8N Neo2 Plat & USB-keyboard problems

Does anyone have problems with an USB-keyboard? Sometimes (not very often), the USB-keyboard just stop working in windows. When I unplug the USB-cable and put it back, keyboard start woriking again.
Always, when I switched off & on the power supply and then turned on the computer, the keyboard won't work. You cannot go to bios etc. Again, I have to unplug the USB-cable.
The other USB-devices, mouse and priter, work perferctly. There is nothing wrong with the keyboard, I have tried it in another computer.

Quote from: bejon2000 on 22-March-05, 17:56:25
- What OS / ServicePacks ?
- What USB settings in bios ?
- Do you use std. Windriver or installed the driver that came with the keyboard ?
- What MoBo bios version ?
- Any IRQ conflicts ?
Please make full system spec.
- WinXP sp2
- USB KB/Storage Support Enabled
- USB Mouse Support Enabled
- Standard windriver (I dont think this is the problem, because keyboard does not work at all also before windows start loading)
- New bios 1.5
All this started to happen when I flashed the bios to version 1.5x mod.

Problem with USB travel keyboard on Windows 7 (some letters become a number)

Hi
I have an USB Travel Keyboard with trackpoint and touchpad. Have used for years in XP.
Now I have bought a new computer, using Windows 7 and Asus P6X58D Premium motherboard.
After installing Windows 7 I noticed that when I press some keys I get a number instead of a letter.
I have managed to install drivers for the USB travel keyboard. And can enter the place where I can change speed of TrackPoint etc....
Now some weird stuff:
The keyboard actually work if I e.g. enter Internet via "Asus Express Gate".
(This is a feature with the motherboard which enables me to run some small numbers of applications without having to start windows, thus enabling superfast access to Internet etc.)
If I let Windows 7 start, then some keys/letters only show numbers.
To me it sounds weird if keyboard only works in "Asus Express Gate" applications and not in when I e.g. use Internet or any text editor in Windows 7.
Maybe there is a settings in BIOS that is set automatically when entering "Asus Express Gate", that I might have to set manually to make the USB keyboard work while in Windows 7 (64bit) ???
I have looked in the BIOS UI without any luck...
Any suggestions?

Before you spend money, see Javascript Error! Error number: 45 error string: Objects is invalid line: 387, Line 428

Usb keyboard problems

I have a IMac and I cleaned my usb keyboard, when I connect the keyboar back it didn't work anymore but the mouse that is connected to the keyboard usb port is workin good. What can I do?

Apparently cleaning caused the keyboard itself to quit. The keyboard also acts a USB hub, and since your mouse is working it means the hub function of the kb is ok.
Cleaning should not destroy a kb, but if none of the keys is working, the kb is probably dead.
If you used a liquid cleaner, just letting the kb dryout might help. Nothing else I can think of without details of how the cleaning was done.

Apple USB keyboard does not work with one internal usb port

Hi everyone,
hope someone can help me to solve my problem. I have a MPB13 retina late 2013 since something like 3 months. I have additional screen (dell), usb wired keyboard (apple) and BT magic mouse.
Since a few days, my usb keyboard does not work well. It only want to work properly when plugged to the rights side usb port internal port and not anymore on the left one. It also work on a usb external concentrator. Before, I had no problem, it worked perfectly. There was no problem such as cofee on it...
After searching the web on such problem, I tries a few things such as:
I tried the keyboard on another computer (windows): works fine
I tried usb stick and external DVD reading on the left internal usb ports: works fine
I switch the MPB off and turn it back on: the usb keyboard still does not work on the left usb port
I tried the SMC and PRAM reset : nothing
Any idea ??
Thanks
Guillaume

I'm facing the same problem, found any solutions ?

External USB keyboard does not work with T60 after BIOS upgrade

External USB keyboard does not work properly with T60 after 2.26-1.07 BIOS upgrade.
It does the same with or without the docking station.
Anyone else bumped into this problem yet?
Has someone found any fixes for this?
t

Hi and welcome the forum!
Try uninstalling all USB hub devices from the device manager and reinstalling them again, particularly the keyboard's.
v2.26 is supposed to fix the issue according to lenovo:- http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-63024
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

Problem of USB keyboard on K7N2L

Similar Messages

Maybe you are looking for