Problem with DAQmx and Real Time PCI-7041/6040E.

Problem with DAQmx and Real Time PCI-7041/6040E.
I have a problem with the Real Time card PCI-7041/6040E, I think it is properly installed because my software run with the traditional NI-DAQ. When I try to use the new DAQmx to acquire one signal, Labview doesn't see any device for de DAQ card 6040E.
Information, I work on Windows XP and LabView v7.0.0 (NIDAQ RT v7.0.0, NI-Serial RT v2.5.2, NI-VISA v3.0.1 and NI-Watchdog v2.0.0).
Could Labview RT run with new DAQmx ?
What can I do to use DAQmx with PCI-7041/6040E?
Thanks for your help !

Hello,
I refer to your posts because i am using the PCI 7041/6040E card as
well but without any success to make it work. The problem I have
already described in the following thread:
http://forums.ni.com/ni/board/message?board.id=170&message.id=120198
Would be nice if you had a look on it, maybe you can help me. BTW, the
thread starts with a problem of someone else, the difficulties I
encountered are to be found a little bit to the bottom of the thread's
page.
Thank you!
Dirk Völlger
Darmstadt
Message Edited by ratschnowski on 07-28-2005 07:14 AM

Similar Messages

I have problem with playback in real time

playback in real time is slowly, i have BlackMagic duo decklnik card
what is the problem should i have to change the settings on the project?
My english isn't good, hope you will understand me.
Thank You.

>Is mov file 1920 x 1080
That doesn't really say much - what is the FORMAT of the media? Look at the Item Properties. Posting a screen shot of the Item Properties would help. Do the same with the Sequence Settings.
>how can i change FCP's RT settings to Dynamic.
Use the drop-down RT menu near the upper left-hand corner of the Timeline.
Also please answer the other questions:
Where is the media stored?
How is that hard drive connected to your Mac?
How much available free space on each hard drive (percentage)? Please list free space individually for each hard drive.
-DH

Problem with DateDiff and Date/Time value.

The form below displayed perfectly until I added the line for DateDiff between VacStart and VacEnd. I receive an error message;
An error occurred while evaluating the expression:
#DateDiff("w", "VacStart", "VacEnd")#
Error near line 48, column 51.
Parameter 2 of function DateDiff which is now "VacStart" must be a date/time value
The error occurred while processing an element with a general identifier of (#DateDiff("w", "VacStart", "VacEnd")#), occupying document position (48:50) to (48:86).
I have tried changing the DB value to Date/Time as well as Text and get the same result each time. Any help would be greatly appreciated. Here is my code:
<cfquery datasource="manna_premier" name="TM_log">
SELECT *
FROM TMStatusLog
</cfquery>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1" />
<title>TM Status Log</title>
</head>
<body>
<p align="center" class="style4">Territory Manager Status Log </p>
<table width="1448" border="0">
<tr>
    <th width="71"><span class="style3">ID No.#</span></th>
<th width="88"><span class="style3"> Date</span></th>
<th width="166"><span class="style3">TM Name</span></th>
<th width="129"><span class="style3">Status</span></th>
<th width="139"><span class="style3">Vac Start </span></th>
<th width="137"><span class="style3">Vac End</span></th>
<th width="203">Ttl Days </th>
<th width="203"><span class="style3">DSR Ride Along Name</span></th>
<th width="274"><span class="style3">Service Call Name</span></th>
</tr><cfoutput query="TM_log">
<tr>
    <td><span class="style3">#ID#</span></td>
    <td><div align="center"><span class="style3">#DateFormat(LogDate, "mm/dd/yyyy")#</span></div></td>
    <td><div align="center"><span class="style3">#TerritoryManager#</span></div></td>
    <td><div align="center"><span class="style3">#Status#</span></div></td>
    <td><div align="center"><span class="style3">#DateFormat(VacStart, "mm/dd/yyyy")#</span></div></td>
    <td><div align="center"><span class="style3">#DateFormat(VacEnd, "mm/dd/yyyy")#</span></div></td>
<cfif VacStart IS NOT "Null">
    <td><div align="center"><span class="style3">#DateDiff("w", "VacStart", "VacEnd")#</span></div></td>
</cfif>
    <td><div align="center"><span class="style3">#DSRName#</span></div></td>
    <td><div align="center"><span class="style3">#ServiceName#</span></div></td>
</tr></cfoutput>
</table>
</body>
</html>

Error Diagnostic Information
An error occurred while evaluating the expression:
#DateDiff("w", VacStart, VacEnd)#
Error near line 47, column 48.
Parameter 2 of function DateDiff which is now "" must be a date/time value
The error occurred while processing an element with a general identifier of (#DateDiff("w", VacStart, VacEnd)#), occupying document position (47:47) to (47:79).
Any other suggestions? Thanks!
Well... what does the error message say?
Parameter 2 of function DateDiff which is now "" must be a date/time value
What does this tell you? What is parameter 2 of that function call? It's VacStart. So it's saying VacStart is an empty string, and it's saying an empty string is not a valid value for that parameter.
So the question you need to ask yourself is whether you expect VacStart to be an empty string? Or do you perhaps expect it to be a date? I would guess you're expecting it to be a date. So the question becomes... Why is VacStart an empty string?
Adam

Problems with mouse and showing time

Hi,
I wish you can help me how to use the mouse as I have an
audio and need tje mouse pointer to point at an image
simultaneously with the audio voice?
Also I need to show the time (digital time like a clock 1:22
minutes) simulateanously with the project movie? which starts and
ends with the audio file ?
Thanks

Hi furrey
oo time show that would create the audio to make an
application in flash for that, do not understand very well the
first part, the pointer work simultaneously with the audio that

Problems with Graphics and a Timer...

Alright so what I'm trying to do is when my character attacks (after the user pushes the ctrl button) I want the attack sprite to show, along with a simple slash graphic, then after less than a second I want the graphic gone and the sprite to return to standing mode. the problem is that it doesn't return, it just stays with the graphic and the attack sprite until the user moves.
here's the attack sub
        public void attack(){
                at=true;
                udchar(3,"attack1");
          sleep(300);
          repaint();
        }here's my sleep sub
        public void sleep(long l){
                try{
                        Thread.sleep(l);
                catch(InterruptedException e){
                        return;
        }and here's my paint sub
        public void paint(Graphics g){
                bufferGraphics.drawImage(background,0,0,10000,600,this);
                bufferGraphics.drawImage(sidebar,720,0,200,600,this);
                bufferGraphics.drawImage(chara,px,py,128,128,this);
                bufferGraphics.drawImage(sworda,px,py,128,128,this);
                bufferGraphics.drawImage(hi,6,507,96,96,this);
                bufferGraphics.drawImage(li,200,507,96,96,this);
                bufferGraphics.drawImage(mi,394,507,96,96,this);
                if(at==true){
                        if(dir.equals("right"))
                                bufferGraphics.drawImage(slice,px+100,py+20,128,128,this);
                        else
                                bufferGraphics.drawImage(slice,px-100,py+20,128,128,this);
                        at=false;
                g.drawImage(offscreen,0,0,this);
        }Help would be much appreciated. I'm not sure if I need to include any other parts of my code or not. If I do just let me know and I'll post that part of the code when I get home from work. Thanks in advance.

There are a variety of Graphics forums that can provide the specialized help you need though, such as Java2d and Java3d, about 1/3 of the way down the forum list.

Fico interview questions and Real time tickets with resoving details

MODERATOR: Do not post (or request) email address or links to copyrighted or confidential information on these forums. If you do, the thread will be LOCKED and all points UNASSIGNED.
hi sap gurus
i have done sap-fico iam in job trails. can any body help me Fico interview questions and Real time tickets with resoving details
regards
prasad.v
Edited by: chinna prasad on Jun 5, 2008 4:10 PM

Hello Prasad,
Before attending interviews.....First you need to understand general things like CV writing, projects, sub modules etc., you should be gain knowledge on these concepts then you can move further.
1. CV 2.Projects 3.your strenths in sap (reading..reading...reading....practice...practice...practice)
2.you please interact with your friends who is on trails, then you can get more information like interview process, methodology, technical etc.,
I am sending some real time interview tech questions which will useful for you.
Questions:
1.When tickets are raised by end users who will give priority? After resolve the tickets who will close the status?
2.In real time at a time how many normal periods, special periods, MM periods we can open?
3.What is client dependant & Independent?
4.How to transport configuration settings from one client to another client or production client, which tools we can use for transport?
5.Why we donu2019t assign business area to company code?
6.What is the difference between General GL A/c, Control A/c, Reconciliation A/c & Offsetting A/c?
Answers:
1.The priority is generally decided by the Coordinator on the client side. After tickets are resolved, they will have to be closed by the coordinator on the customer site
2. In FI as many as you wants. In MM only 2 (current month + previous
3.Certain tables and customizations made in one client will affect the other clients also - then it is cross client i.e, client dependent. While if the changes made in one client has no impact on the other client - it is said to be client independent
4.Transports from one server to the other can be made with the help of transport requests. When a configuration is done the system generates a request number. First release the task and then release the request. Use TC-SE10 / SE09, SE09: workbench transport; SE10: customizing transport. But currently no such difference actually exists.
5.because in case of multiple company codes, same business area can be used across company codes. Business area is cross company code, means it is not confined to one company code thatu2019s why we don't assign BA to any of the company codes. It is client dependant, not company code dependant. We can pass values from one company code to any of the BA in that client.
6.General GL Account are those used for standard posting like for example Income and Expenses Accounts
- Control Account are basically used for reconciliation between modules like FI and CO, to ensure that both the modules are in sync.
- Reconciliation Account are those specific covering ADK (A-Assets, D-Customer, K-Vendor). For example a Customer Master would be mapped to a Bills Receivable Reconciliation Account and any transaction that needs to be posted are done against the customer code.
- Offsetting Account are used for variety of reasons and few examples are Intercompany Postings, at the time of Implementation when TB and Balance sheet are uploaded would be offsetted against a dummy account.
All the best.....dont forget and pl assign points if useful and if u have any querries pl revert back
thanks
Anil

I'm having problems with iPhoto and the facebook set-up. Every time I attempt to do so it says an error has occured and try again later. I have not seen a solution posted. Therefore, how does one contact Apple to solve the problem? I'm new to the worl

I'm having problems with iPhoto and the facebook set-up. Every time I attempt to do so it says an error has occured and try again later. I have not seen a solution posted. Therefore, how does one contact Apple to solve the problem? I'm new to the world of iMac but I find it a bit frustrating trying to solve basic issues/problems:(

For what it's worth, you posted this in 2011, and here in 2014 I am still having this same issue. Over the last two days, I have had to unlock my apple account 8 times. I didn't get any new devices. I haven't initiated a password reset. I didn't forget my password. I set up two factor authentication and have been able to do the unlocking with the key and using a code sent to one of my devices.
That all works.
It's this having to unlock my account every time I go to use any of my devices. And I have many: iMac, iPad, iPad2, iPad mini, iPhone 5s, iPod touch (daughter), and my old iPhone 4 being used as an ipod touch now. They are all synced, and all was working just fine.
I have initiated an incident with Apple (again) but I know they are just going to suggest I change my Apple ID. It's a simple one, and one that I am sure others think is theirs. I don't want to change it. I shouldn't have to. Apple should be able to tell me who is trying to use it, or at least from where.
Thanks for listening,
Melissa

Error -200141 when doing buffered events with DAQmx and PCI-6602

When doing buffered events with DAQmx and PCI-6602 I get error 200141 - Data was overwritten before it could be read by the system.
This error is generated ONLY with random inputs >200/sec.
My setup is :
DAQmxCreateCIVCountEdges(taskhandle,"Dev1/ctr3"....
DAQmxCG+FGSampClkTiming(taskhandle,"/Dev1/FPI35",...
DAQmxSetCICountEgdesChan(taskhandlem,"", "/Dev1/80MHZTimeBase")
DAQmxSetChanAttribute(taskhandlw,",",DAQmx_CI_DataXferMech,DAQmx_Val_DMA,0);
Can somebody help ?

i'm getting the same Error-200141, while reading semiperiods. (Meas_Buffered semiperiod continous)
while loop ex.rate seems to be pulsewidth*no.Samples to read. in my case PW=60ms
Input buffer size measured with Property node= 10000
why this error happens?? i cant use any mode other than implicit timing for semi-period measurement right??
more info: all the ai channels are used ~ 16 differencial.
i found one solution which is _ reinitializing the whole task if an error occur. is this the right way??
Kudos always welcome for helpful posts
Attachments:
Counter_1_Meas Buffered Semi-Period-Continuous_main_lv09.vi ‏34 KB
SemiPeriod_Reconnect Counter on Error.vi ‏35 KB

HT5361 Today, I experienced a problem with my mail. the time and date on each email received and sent is 18-06 and the date is 22nd July irrespective of the actual time

Today, I experienced a problem with my mail. the time and date on each email received and sent is 18.06 and date as 22nd July. Thank you John

Incorrect date or time displayed in various applications

Problem with DMGs and error: "No Mountable File Systems"

Problem with DMGs and error: "No Mountable File Systems"
The files are not corrupt. The problem is occurring with all DMGs that are apparently formatted in MS-DOS FAT16. No the file will not mount with Disk utility or any other disk mounter programs I have found.
This is now the second time this occurred and now effects my MBP and my iMac. First time i spent days with Apple support and the only solution was ultimately back up the data, reformat the HD, start over from scratch and reload everything. That lasted about a month before the problem resurfaced and is now an issue on both iMac and MBP.
I tried to identify all the programs I installed immediately before the error, as I am convinced it is the result of a software conflict.
Recent programs includes:
1) upgrading from Parallels 5.5 to 6.0 on both machines.
2) using an HP secure II usb drive and setting up a secure disk.
3) installing new itunes 10
4) new update to Flip For Mac.
The files affected are downloaded dmgs, including personal brain and google earth, both which are formatted in FAT16.
Any help or thoughts? Apple has now spent hours trying and they say i now have to reformat and wipe and start over. That is unacceptable and based on pasted experience the problem is likely to repeat itself. having to wipe and rebuild a HD ever month is not an solution. i need to fid the root problem.
In the meantime, anyone got a real solution on how to extract the data for a DMG using a different method?
Message was edited by: remaia

Where you able to find the solution, i am having the same problem, all was fine till i install some programs only same one i saw did we both did was flip4mac i uninstalled it but the problem is still there, i also restored and erased the hardrive but im not up to doing that all over again. If you found anything out let me know i would greatly appreciate it

Problem with modules and ModuleLoader

Hi everybody,
i'm facing a real funny problem with modules and
moduleLoader, i hope
it's not (only) my fault anyway...
If i create a normal flex project with fBuilder, i'm able to
use
modules in a lot of different ways (as mxml, as as in a
function etc..)...
but if i try to use them in my fds application (created with
fds
eclipse plugin or as a dataServices project) i can't use
modules. The compile-time error message is
always the same:
Could not resolve <mx:ModuleLoader> to a component
implementation
I tried a lot of solutions, paying attention to import all
the classes, to declaration, naming, positioning
etc...but nothing changes, this thing is drivining me
crazy!!!.
I will appreciate anykind of help.
TIA
Fabio

Any idea?

Problem with Class and Classpath

Hello ME Windows Users, now before you place a wry smile on your face, I have a problem with path and classpath. Stop it, I can see you smiling!
By visiting the the last 10 pages of the forum and reading Sun installation notes, some tooldocs and by given some answers by some nice people, I have become an expert in turning off my computer, about 10 times/hr. I still am trying to make my first cup of java.
With the ME computer,
I'm unable to right click on the desktop and go to properties, advanced,
I'm unable to go go start, run, sysedit,
I'm unable to change the ms-dos window of autoexec.bat, it just shuts down.
Now before you tell me, I should of bought a different computer, the only place I can find to modify the path and classpath is in the environment which is in system configuration under tools. Here I have placed numerous configurations, like
C:\java>set path=%path%;c:\j2sdk1.4.2\bin
C:\java>set classpath=%classpath%;.;
;java_dir\bin where ;java_bin is c:\j2sdk1.4.2
.; java_dir\bin; %path% where ;java_bin is c:\j2sdk1.4.2 and the list goes on.
But, I know you are still smiling, the % signs comes up in a dialog box, saying too many, and will not convert the text to the environment to be saved when I close down for the tenth time in the last hour.
Can someone help me before I make a real cup of coffee and accidentally drop it on the ME box.
Have a laugh on me Mik.

C:\java>set path=%path%;c:\j2sdk1.4.2\binGood
But it is no good because it has to many % and a dialog box appears, saying you have too many parameters.
Are you saying I have to shutdown again to answer your ?
From the HELP menu-
To confirm startup commands line by line
Click Start, and then click Shut down.
Click Restart, click OK, and then press and hold the CTRL key until the Windows Startup Menu appears.
Enter the number for Step-by-step confirmation, and then press ENTER.
For each command you want to run, press Y.
If the command runs successfully, you are prompted with the next command.
If the command does not run successfully, you receive an error message.
To skip a command, press N.
Mik

Pulse Generation application with DAQmx and a PXI-6624 module?

What is the best implementation method for the following pulse generation application
using LabVIEW, DAQmx and a PXI-6624 counter\timer module?
I have two rising edge trigger signals (Trigger-1 and Trigger-2).
There is ample spacing between each trigger. They never occur at the same time.
I need to generate a single pulse (fixed width, variable delay) whenever Trigger-1 occurs and
a finite pulse train (fixed width, variable delay, N-pulses) whenever Trigger-2 occurs.
However, the output must appear on one counter output because this composite signal
will be used as a trigger source for another PXI module in the rack.
With DAQmx and a TIO counter\timer can I use both the GATE (for Trigger-1) and
AUX (for Trigger-2) at the same time on the same counter to gate out the desired pulses?
Trigger-1 would be wired to the GATE of CTR0. One Trigger-1 event would generate one pulse on the output of CTR0.
Trigger-2 would be wired to the GATE of CTR1 and the output of CTR1 would be routed to the AUX input of CTR0.
One Trigger-2 event at the GATE of CTR1 would generate multiple pulses on output of CTR0.
Would DAQmx and the PXI-6624 TIO support this implementation?
What is the best way to accomplish the task at hand.
Thank You.
Best Regards,
Scooby

Hi Scooby,
I have looked into the application you have described and I see a potential problem with what you describe. In DAQmx, it is not possible to call the counters of the same DAQ device in the same task, so you cannot have the finite pulse train generation and the single pulse generation tasks running at the same time. What you can do, since you mention the triggers will not occur at the same time, is to stop one counter task while you are triggering another. The way I would suggest you merge the outputs is with a two input Or logic gate to avoid damaging your counters. Your signals will effectively be added together by this logic gate. I do not see any way to merge the outputs internal to the DAQ device.
Please let me know if I can be of additional assistance.
Laura

Problem with JFrame and busy/wait Cursor

Hi -- I'm trying to set a JFrame's cursor to be the busy cursor,
for the duration of some operation (usually just a few seconds).
I can get it to work in some situations, but not others.
Timing does seem to be an issue.
There are thousands of posts on the BugParade, but
in general Sun indicates this is not a bug. I just need
a work-around.
I've written a test program below to demonstrate the problem.
I have the problem on Solaris, running with both J2SE 1.3 and 1.4.
I have not tested on Windows yet.
When you run the following code, three JFrames will be opened,
each with the same 5 buttons. The first "F1" listens to its own
buttons, and works fine. The other two (F2 and F3) listen
to each other's buttons.
The "BUSY" button simply sets the cursor on its listener
to the busy cursor. The "DONE" button sets it to the
default cursor. These work fine.
The "SLEEP" button sets the cursor, sleeps for 3 seconds,
and sets it back. This does not work.
The "INVOKE LATER" button does the same thing,
except is uses invokeLater to sleep and set the
cursor back. This also does not work.
The "DELAY" button sleeps for 3 seconds (giving you
time to move the mouse into the other (listerner's)
window, and then it behaves just like the "SLEEP"
button. This works.
Any ideas would be appreciated, thanks.
-J
import java.awt.BorderLayout;
import java.awt.Cursor;
import java.awt.event.ActionEvent;
import java.awt.event.ActionListener;
import javax.swing.JButton;
import javax.swing.JFrame;
import javax.swing.JPanel;
import javax.swing.SwingUtilities;
public class BusyFrameTest implements ActionListener
private static Cursor busy = Cursor.getPredefinedCursor (Cursor.WAIT_CURSOR);
private static Cursor done = Cursor.getDefaultCursor();
JFrame frame;
JButton[] buttons;
public BusyFrameTest (String title)
frame = new JFrame (title);
buttons = new JButton[5];
buttons[0] = new JButton ("BUSY");
buttons[1] = new JButton ("DONE");
buttons[2] = new JButton ("SLEEP");
buttons[3] = new JButton ("INVOKE LATER");
buttons[4] = new JButton ("DELAY");
JPanel buttonPanel = new JPanel();
for (int i = 0; i < buttons.length; i++)
buttonPanel.add (buttons);
frame.getContentPane().add (buttonPanel);
frame.pack();
frame.setVisible (true);
public void addListeners (ActionListener listener)
for (int i = 0; i < buttons.length; i++)
buttons[i].addActionListener (listener);
public void actionPerformed (ActionEvent e)
System.out.print (frame.getTitle() + ": " + e.getActionCommand());
if (e.getActionCommand().equals ("BUSY"))
frame.setCursor (busy);
else if (e.getActionCommand().equals ("DONE"))
frame.setCursor (done);
else if (e.getActionCommand().equals ("SLEEP"))
frame.setCursor (busy);
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.print (" finished");
else if (e.getActionCommand().equals ("INVOKE LATER"))
frame.setCursor (busy);
SwingUtilities.invokeLater (thread);
else if (e.getActionCommand().equals ("DELAY"))
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (busy);
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.print (" finished");
System.out.println();
Runnable thread = new Runnable()
public void run()
try { Thread.sleep (3000); } catch (Exception ex) { }
frame.setCursor (done);
System.out.println (" finished");
public static void main (String[] args)
BusyFrameTest f1 = new BusyFrameTest ("F1");
f1.addListeners (f1);
BusyFrameTest f2 = new BusyFrameTest ("F2");
BusyFrameTest f3 = new BusyFrameTest ("F3");
f2.addListeners (f3); // 2 listens to 3
f3.addListeners (f2); // 3 listens to 2

I've had the same problems with cursors and repaints in a swing application, and I was thinking of if I could use invokeLater, but I never got that far with it.
I still believe you would need a thread for the time consuming task, and that invokeLater is something you only need to use in a thread different from the event thread.

Problems with Safari and Firefox (HTTP?)

Problems with Safari and Firefox (HTTP?)
On a laptop G4, 10.5.8 and Safari 5.02 I experience the following:
On the account of my oldest daughter everything works fine, i.e. wireless internet works and no problems with mail or safari.
On the same laptop, on the account of my other daughter, the wireless is OK, she can mail etc. But safari nor firefox works. It says: can’t find server (whatever site) and in the activity window it looks if safari tries to open files (in the safari preferences-folder) in stead of http. Same applies to Firefox, so maybe it has more to do with HTTP in general?
What goes wrong? What to do? I tried the following on the host terminal (tips from Apple)
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false
and
defaults delete com.apple.safari WebKitDNSPrefetchingEnabled
but that did not help,
Nanne

I'm still wondering why it happens now at this moment in time...
PC does seem to be a bit odd & inconsistent, the few times I've tested with it, at least so far as we content filtering goes; and if I remember rightly, you're not the first to report previously ok settings suddenly preventing some or all internet until pc is switched off altogether.
It may work when re-enabled

Problem with DAQmx and Real Time PCI-7041/6040E.

Similar Messages

Maybe you are looking for