Problem with system recovery for a new hard drive in my Pavilion p6210y Windows 7 Premium 64bit

   I decided to swap out my hard drive when my computer would fail to start up or crash right after starting. Diagnostic tool at startup said the hard drive was faulty and other times I would get BIOHD-1 and BIOHD-2 errors. I replaced the old WD Caviar Blue 640GB with a new Caviar Green 1TB. I ordered and received from HP a system recovery disc set which included five discs labeled:
Use This First! System Recovery,
System Recovery 1:1,
SYstem Recovery 1:3,
System Recovery 2:3, and
System Recovery 3:3.
   After putting in the new hard drive I used the "Use This First!" disc and everything seemed to be going fine. The scene showed "Loading Windows" or something like that. After about 10 minutes the CD drive opened and the Monitor showed three images: a big green check mark which I assume meant everything was good up to that point; a graphic showing the removal of the first disc; and a graphic showing three discs to be put in. Wondering whether to put in the System Recovery 1:1 disc or the System Recovery 1:3 disc, I noticed that the drive bay closed with the "Use This First" disc still in. I managed to get the Drive to open after pressing the open button quite a few times. I closed it with the 1:3 disc and nothing happened (no light showing activity in the DVD drive). After a minute or so I managed to get the drive open again after quite a few times pressing the open button. I put in the 1:1 disc and still nothing. At this point I could only open the drive bay with a paper clip in the release hole. With the computer unresponsive and the monitor still showing the same as when the first disc came out, I decided to turn it off with the "Use this First!" disc in the drive hoping to start from the beginning again. Now the directions that came with the HP System Recovery discs state:
   CAUTION: Do not turn off the computer, or use the keyboard or mouse during this time. Doing so will interrupt or damage the software installation.
   Now when I turn the power on I get either:
the HP blue screen with the green hand, (F11=system recovery), (F9=Diagnostics), (F10=Setup) and (ESC=Boot Menu). pressing esc, F9, F10 or F11 does nothing.
Or the HP blue screen appears and then almost immediately goes to the black screen with " Reboot and select proper boot device or insert Boot media in select Boot device and press a key". I've gotten this scene while trying almost every System Recovery disc in the drive. Hitting a key does nothing other than repeating the same message.
Once I got a "The file is corrupt. The file header checksum does not match the computer checksum" error. That appeared only once in about 30 try's.
   The open DVD drive button works sometimes and not other times. I can't seem to figure out a pattern for when it will work.
   I don't know whether I might have accidentally moved the mouse or hit the keyboard during the first attempt. Can I do something to the new hard drive to get it back to a state where it can start from the beginning again? Might it be a problem other than the old hard drive. Anyone have any suggestions?

Satellite L505D-S5983
Windows 7 Home Premium 32-bit
Yes, of course! See the link to your model's spec above.
My apologies. The previous link went to a spec for the Satellite A505-S6960 (which came with Windows Vista installed). I had too many spec pages open at the same time and got them mixed.
So, are you telling me that I won't get this one to work?(the BPKT)
No. But you may face the problems that I outlined in this message.
-Jerry

Similar Messages

Problems with copying iPhoto library onto new hard drive from external HELP

I had to get a new hard drive installed onto my MacBook Pro, but was able to copy my iPhoto library onto my external hard drive via another computer before the old hard drive failed. Now, I am trying to copy that library back onto my MacBook.
After I copied the library onto the MacBook, when iPhoto was opened, it showed no photos but I could see album titles. Then when I opened iPhoto while holding down the option key, it was all clumped into one event and not nearly all of the photos were there. Also, I have right-clicked on the library to see package contents and everything seems to be there, but I don't know how to make it all show up in the library.
I've downloaded iPhoto Library Manager because I thought that might help (but haven't used it yet -- don't know how) and I just need some help to recover my iPhoto library... and is there a way to restore all the separate events imported and time/date stamps, in order to get all the photos in chronological order?

Should I just go through the iPhoto Library package contents and drag every folder into iPhoto?
No. That will get you massive duplication.
Try these in order - from best option on down...
1. Do you have an up-to-date back up? If so, try copy the library6.iphoto file from the back up to the iPhoto Library (Right Click -> Show Package Contents) allowing it to overwrite the damaged file.
2. Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
3. If neither of these work then you'll need to create and populate a new library.
To create and populate a new *iPhoto 08* library:
Note this will give you a working library with the same Events and pictures as before, however, you will lose your albums, keywords, modified versions, books, calendars etc.
In the iPhoto Preferences -> Events Uncheck the box at 'Imported Items from the Finder'
Move the iPhoto Library to the desktop
Launch iPhoto. It will ask if you wish to create a new Library. Say Yes.
Go into the iPhoto Library (Right Click -> Show Package Contents) on your desktop and find the Originals folder. From the Originals folder drag the individual Event Folders to the iPhoto Window and it will recreate them in the new library.
When you're sure all is well you can delete the iPhoto Library on your desktop.
In the future, in addition to your usual back up routine, you might like to make a copy of the library6.iPhoto file whenever you have made changes to the library as protection against database corruption.
Regards
TD

Problems with external/usb after installing new hard drive

After having a new hard drive installed (from Mac 10.5.2 to 10.6.8) I have experienced 2 problems so far:
1. I am getting no response (from anything connected from my usb port) ie. mouse. But plugging in the mouse directly into the mac works fine.
2. After a few minutes, the sound from my production speakers (connected: macbook->usb cord->sound card-> production speakers) starts to skip and then no sound at all, however my soundcard is still working as I see the light is on.
Can anyone let me know how this can be fixed? I never had these problems before getting the new hard drive.

try doing a PRAM/NVRAM reset.......
that might sort out your issues.......
good luck.....hope it works for you...

Reinstall Windows 8 on workstation with no recovery media and new hard drive.

Hello. I am needing help with a specific request.
We have a workstation what is running Windows 8. The hard drive failed. The machine has no recovery media that was created, however it is orderable through HP.
With that in mind, where are the tools for IT Pros to reinstall Windows 8 from .ISO or USB media, as we could do in Windows 7 and previous versions?
Windows 8 keeps the license key stored in the BIOS from what I read, and one option is using an .ISO for Windows 8 from an MSDN account. The install will scan the BIOS for the key, find it, and will activate Windows 8.
We are Silver Partner. currently we are turning people away or telling them they must have their Factory Recovery Media for us to reinstall Windows 8 after hard drive failures, since we cannot find any .ISO available, and there is no plain Product Key on
the machine.

Hi ,
"one option is using an .ISO for Windows 8 from an MSDN account."I am afraid it will not work.
The copy of Windows that the OEM installs on a computer is valid only on that unique computer, so it can only be reinstalled and reactivated from the OEM-provided recovery media on that computer. So
I am afraid an .ISO for Windows 8 from an MSDN account won`t be activated automatically.
Here is link for reference:
Windows Activation in Development and Test Environments
http://technet.microsoft.com/en-us/library/dd981009.aspx
1.I agree with britishdhez, the best way to solved this issue is contactting the manufacture for a recovery media.
2.As an alternative choice, there is a similar situation and Justin offers several other solutions. Here is the link for reference:
How to install and active a windows 8 after change a hard drive?
http://www.tomshardware.com/forum/3591-73-install-active-windows-change-hard-drive
NOTE: This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on these sites.
Best regards

TS1394 is mac os x 10.4.11 compatible with my passport for mac portable hard drive?

is mac os x 10.4.11 compatible with my passport for mac portable hard drive?

The specs for the Passport Essential HD says:
Macintosh
Available USB port
Mac OS X 10.5.x
Don't know why it wouldn't work with Tiger.
 Cheers, Tom

Is it time for a new hard drive?

My iMac early 2008 has been running extremely slow even after i reduced 320 gb hard drive so it only has about 150 gigs occupied now. 2 GB memory. I just ran Disk Utility and it said it "stopped verifiying MacIntosh HD. This disk needs to be repaired. Start your computer with another disk." I haven't done that yet. I have everything backed up on Time Machine to an external hard drive. A friend says the HD is going bad and needs to be replaced. Is that right? All advice greatly appreciated.

From the given information I'd find a more knowledgable friend. The first thing you need to do is repair your drive:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If the above indicates the drive is OK after repairs are completed, then you can focus on some maintenance to help improve performance:
Kappy's Personal Suggestions for OS X Maintenance
For disk repairs use Disk Utility. For situations DU cannot handle the best third-party utilities are: Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible. TechTool Pro provides additional repair options including file repair and recovery, system diagnostics, and disk defragmentation. TechTool Pro 4.5.1 or higher are Intel Mac compatible; Drive Genius is similar to TechTool Pro in terms of the various repair services provided. Versions 1.5.1 or later are Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts had been significantly reduced in Tiger and Leopard. These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems.
I would also recommend downloading the shareware utility TinkerTool System that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc. Other utilities are also available such as Onyx, Lion Cache Cleaner, CockTail, for example.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the commandline. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand. I also recommend booting into safe mode before doing system software updates.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
Backuplist
Carbon Copy Cloner
Data Backup
Deja Vu
iBackup
JaBack
Silver Keeper
MimMac
Retrospect
Super Flexible File Synchronizer
SuperDuper!
Synchronize Pro! X
SyncTwoFolders
Synk Pro
Synk Standard
Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac Maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate.
If none of the above help then try reformatting the drive and installing a fresh copy of Snow Leopard.

How to use recovery dvd on new hard drive, install window 7

hello, i have trouble with my laptop. my hard drive got bad sectors and now i need to replace my hdd to new one. im not sure how to reinstall window 7 on my new hdd.
is it possible to install operating system on new hard drive using recovery disk? and how?

Hi,
Yes, recovery discs will work on a new hard drive, but it's generally best to ensure that the replacement drive is of the same capacity ( slightly larger is Ok ) as the original - recovery discs can have issue when used on a drive that has a smaller capacity than the original.
When you have replaced the HDD, all you need to do is as follows.
Tap away at the esc key as you start the notebook to enter the Start-up Menu.
Insert the 1st Recovery Disc.
Select Boot options ( f9 ), use the arrow keys to select the CD/DVD drive and hit enter. You may also get a prompt to 'Press any key to continue' - do this if asked.
You will be prompted to insert subsequent discs as required.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

HP System Recovery DVD incorrectly formats hard drive (WIN Vista HP SP1 64-bit 510141-001)

HP Pavilion DV4-1225dx
Vista Home Premium 64-bit
AMD Turion x2
I had previously posted the issue as "HP System Recovery Fails on new HDD", however it appears that the reason it is failing is due to incorrect formatting of the hard drive:
Went to purchase the oem HDD @ Tiger Direct (Hitachi 0A56415 Travelstar 5K320 Mobile Hard Drive - 2.5", 5400 RPM, SATA 3G, 250GB, 8MB Cache) but found it was out of stock. I purchased the suggested replacement (WD Blue 320GB Mobile Hard Drive - Designed for everyday computing - 2.5", SATA 3Gb/s, 5400RPM, 8MB C...)
I have attemptted the System Recovery several times each failing with errors. But after each failure the HDD is found to be incorrectly formatted as documented in the following link:
System Recovery Fails on new HDD
hp G71-340US WIN 7 HP 64 Bit
hp pavilion dv4-1225dx VIsta HP 64 Bit
hp pavilion zd7000 WIN XP Pro
hp pavilion xv886 WIN Millennium / WIN XP Pro
hp deskjet 6980xi
hp pavilion xt236 / ze4200 WIN XP Media Edition

Slolearner,
After doing a little research, I believe your issue may be related to your new hard drive being an AF (Advanced Format) drive. Please see "WD Scorpio® Blue™ SATA/PATA Hard Drives", which indicates your WD3200BPVT may an AF drive.
Please see "Cannot Recover the PC after Replacing the Hard Drive with an AF Drive (Windows 7 and Vista)" for information on this subject. While this document isn't for your specific computer, it is generic enough that it applies to your situation. If you wish to use your HP Recovery Discs successfully, you may need to purchase a non-AF drive.
If your computer boots into Windows, please see "Identifying an Advanced Format Hard Drive" to download and run the HP Advanced Format Hard Drive Information tool.
If it is an AF drive, please see "Preparing Advanced Format Hard Drive for Windows" and "Improving the Performance of an Advanced Format Hard Drive" for more information on the subject and possible steps to be taken to resolve your issue.
Lastly, it may be necessary to follow Paul_Tikkanen's advice and install Windows Vista from a Microsoft Windows Vista installation disc as follows;
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
If you can still read the 25 character Microsoft Vista product key on the bottom of your PC, you can make your own plain Vista installation media and use that to at least get the OS on your PC.
Here is how to do that if you can read that key:
Please click on the link below, click on the Windows Reinstallation Guide [27-07-2013] pdf link on the upper left of the page and then read the instructions for doing this starting on page 302.
http://philipyip.wordpress.com/dell-community-forums/
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
You may also consider purchasing a copy of Windows 7 and installing that instead. Windows 7 SP1 has much better support for AF drives than the previous versions of Windows.
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

System recovery copied to external hard drive, Win 7 64 bit

HP 2000-369WM Notebook PC
Windows 7 Home 64 bit
No error messages, just can't print to printer
Connection: hardwired LAN
Used HP's troubleshooter for printers
Checked all systems and none failed
Expertise: mid level
Ran NAV several times, including in Safemode, finds nothng
Tried to contact NAV instant chat support with no success downloading their troubleshooting sw.
Tried it with HP also with no luck in connecting with them.
Checked Printer Spooler in Admin Tools; Services, Says Started
Appears virus modified Recovery partition on 6-10-12.
Just purchased pc 1 mo. ago
No changes made prior to problem, printed fine yesterday.
Looked at several problem resolutions in this forum, but found none regarding my problem, other than buying system disc from HP.
I made a system recovery copy on an external hard drive just after buying my notebook. It appears that my system recovery partition has been modified by a virus. My question is: how do I use it to do a full system recovery? When I use my pc's software to do this, I choose "Use a system image you created earlier to recover your computer. Then it asks me to insert the admin's password to pull the Recovery program from the hard drive! The next window doesn't give me the 3rd step, which is: Click "Use a system image you created earlier to recover your computer", and then follow the steps. It only shows:" resotre using preinstalled recovery options, or resore using a Windows installation disc or a system repair disc." Thank you very much, your assistance is greatly appreciated!! Ric

Burn a Repair CD to boot from:
http://www.howtogeek.com/howto/5409/create-a-system-repair-disc-in-windows-7/
After booting from it try the restore from Image:
http://www.howtogeek.com/howto/7702/restoring-windows-7-from-an-image-backup/
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

HT201372 used this to make a bootable copy for a new hard drive installation. copied the install find but gave error code 110 when making the disk bootable.. Any help in what this code is

Used createinstallmedis to make a copy of the Mavericks app for use in a new hard drive install.. Copied find but gave error code 110 and failed to make the flash drive bootable.. Any help in what errror code means?

Did you partition and format the flash drive first? See the following:
Make Your Own Mavericks, Mountain/Lion Installer
After downloading the installer you must first save the Install Mac OS X application. After the installer downloads DO NOT click on the Install button. Go to your Applications folder and make a copy of the installer. Move the copy into your Downloads folder. Now you can click on the Install button. You must do this because the installer deletes itself automatically when it finishes installing.
2. Get a USB flash drive that is at least 8 GBs. Prep this flash drive as follows:
Open Disk Utility in your Utilities folder.
After DU loads select your flash drive (this is the entry with the mfgr.'s ID and size) from the leftside list. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
Select the volume you just created (this is the sub-entry under the drive entry) from the left side list.
Click on the Erase tab in the DU main window.
Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
Click on the Erase button. The format process can take up to an hour depending upon the flash drive size.
Make your own Mavericks flash drive installer using the Mavericks tool:
Mavericks has its own built-in installer maker you use via the Terminal:
You will need a freshly partitioned and formatted USB flash drive with at least 8GBs. Leave the name of the flash drive at the system default, "Untitled." Do not change this name. Open the Terminal in the Utilities folder. Copy this command line after the prompt in the Terminal's window:
sudo /Applications/Install\ OS\ X\ Mavericks.app/Contents/Resources/createinstallmedia --volume /Volumes/Untitled --applicationpath /Applications/Install\ OS\ X\ Mavericks.app --nointeraction
Press RETURN. Enter your admin password when prompted. It will not be echoed to the screen so be careful to enter it correctly. Press RETURN, again.
Wait for the process to complete which will take quite some time.

Having problems installing PE 2.0 on new hard drive

I'm having problems as I stated. I'm running Windows 7 Ultimate 64bit and had PE 2.0 on the last hard drive. This is a new hard drive, the welcome screen appears, I get the accept license screen and then the installation screen. As soon as I click install Photoshop Elements 2.0, the DVD-ROM drive spins down and stops. I tried using compatibility mode with no success either. I know there are more P E's out there. I own PE 12 too and I want to put 2.0 on the drive for simple things before putting on PE 12.
Any help would be appreciated!

How big is your new hard drive?
If it's not over 1 TB, then try copying the contents of the cd to to your hard drive and then in the Adobe Photoshop Elements folder, right click
on the Setup.exe and choose Run as Administrator
Also, turn off the real time scanning for your virus scanner before installing, just make sure your disconnected from the
internet and don't forget to turn your your virus scanning back on after installing pse 2.

Restoring a home folder backed up using the Backup application (with the umbrella) to a new hard drive running Snow Leopard

I was running OS X 10.4 Tiger on a 2006 iMac. My home folder is backed up on a My Passport 500GB USB external drive using Backup (the original application that came pre-installed with the orange umbrella symbol).
I was intending to upgrade tp Snow Leopard so that I could sync a new iPad with iTunes and iPhoto so had ordered the disc from Apple and was waiting for it to arrive.
2 weeks ago my hard drive stopped - and I took the iMac to a support store (I am currently in Belgium and there is no Apple store here). They confirmed the hard drive was dead and as I had my receipt for Snow Leopard installed this for me.
Now I am trying to restore my home folder but the new OS does not recognise the data. I can see there is nearly 200GB of data on the external drive - but the folders contain small files call backup.log, backup.log.gz, InfoPlist.stringscat, stat0..... all under 5MB.
Applecare told me they did not know about the Backup application and it was not theirs..... then suggested I tried migration assistant.
With migration assistant, I just get a spinning wheel at the initial 'select your disk' page - spinning now for more than 8 hours. I checked on line and the only advice I saw was to use firewire - but my external drive works with the new high speed USB...
Can anyone help?

Thank you for your help - I now have a solution ...in case it helps someone else.....
...I also think I may have been a bit silly...
The solution - thanks to a great guy in Apple Support USA - thank you Matt!!
first I partitioned my hard drive using disk utility - and set 235GB for a separate install - I called it Tiger install disk
this allows your hard drive to act as 2 totally separate systems (by holding down the option key when you start the computer you can choose which you want)
then I reinstalled Tiger from my original discs onto the new part of my hard drive
then I read my backed up home folder and copied it to the Tiger system on the new hard drive section
then I rebooted and started up Snow leopard on the original part of the hard drive
then I used migration assistant to transfer from the 'Tiger install disc' drive - it was recognised by migration assistant
Where I think I may have been a bit silly
I am now not sure if the orginal backup was always visible in Snow Leopard
in Tiger I found backup.sparseimage - which when double clicked opened up my home folder
now that I have istalled Tiger as well - I can also find this in now Leopard... ...so maybe I just hadn't opened all the original folders on my backup disk...
...but for sure migration assistant could not read the backup copy

My MacBook won't boot into recovery mode after new hard drive installation. Please help!

I just installed a new hard drive. On boot it keeps on going to the flashing folder with a question mark inside.
I was able to format the new hard drive but am unable to boot into recovery mode to install the operating system over the air.
When I hold down Command -R it keeps on taking me to the flashing folder.
Please help!

A new hard drive doesn't have a recovery partition. It's totally blank.You're going to need either your original install discs or a Snow Leopard retail disc from which partition, format and install OS X.

Do I need to uninstall apps when getting service for a new hard drive?

My second (home) computer is part of Apple's defective hard drive recall. Do I need to uninstall my creative cloud apps before I take it in to get the new hard drive, or will they just get wiped and then can I install again when it comes back with the totally new hard drive?

Launch one of the installed applications, for example Photoshop and from the Help menu choose Deactivate. This will deactivate all of the applications installed via Creative Cloud.

Computer won't access or stay registered with third party accounts after new hard drive installed

Had a hard drive crash a a few months ago on iMac. Took it to an Apple-certified repair place, and they installed a new hard drive. (And I think updated the OS as well.) iMac is working great, but have run into an odd issue with signing into accounts -- such as stores, banks, etc. Each time I try to sign in I need to reregister the computer or in some cases, I simply can't sign into the account at all, despite using the correct user name and password. Tried calling the third party accounts customer support and got "It's a Mac - we don't have anyone who does that." One other place said it "might have something to do with cookies."
Can anyone help out with this one? It is extremely annoying!
Thanks!!

Thanks. This seems to have worked.
I ran the reinstall and then upgraded back to 10.6.8 via software update, and App Store and iTunes both work now. I was able to log into my iTunes account and my old purchase of 10.7 was there. I'm downloading it now as I type this.
I still have to deal with the fact that iLife and iWork and Xcode aren't working (and probably other things too), but the biggest hurdle seems to be crossed. I'll deal with the other apps tomorrow.
Thanks again!

Problem with system recovery for a new hard drive in my Pavilion p6210y Windows 7 Premium 64bit

Similar Messages

Maybe you are looking for