Problem with the WLAN
Hello
I have the E51 and when trying to connect my mobile using the WLAN, I used a wrong key while asking for a key and I could not changing it to use the correct one. Each time I want to conect to the WLAN it uses the same wrong key and connect automaticly without asking for a new key.
Please help me
1- go to connectivity
2-connection manager
3-current WLAN
4-choose you WLAN
5-option
6-define gate
Similar Messages
-
I have a MBP 5.1 with snow leopard 10.6.8. It has been working fine until few days ago, when it started to have different problems:
1) airport is not working well. it is extremely slow, has difficulties in fully loading pages, looses connectivity, It is not browser related, behaves thesame in safari or firefox; it is not the router/wlan; my husband mbp wifi works fine (as it was mine...) and iphone wifi is also working fine. it sees the signal and different networks. , it is also very very slow in opening skype (after that, it is working ok) if I connect via ethernet cable to the same router, everything works perfectly and with the correct speed.could it be a damaged airport card? a software problem/corruption? logic board? (I hope not, the computer is out of apple care now....)
2) after a certain time (more than hours) of use, the trackpad is behaving strangly, increase sensitivity to touch, unwanted selection of folders, files and text or images in web pages when i move the cursor, the cursor jumping all over the places while writing, ecc I have the impression it starts doing that when I use heavily the CPU ( and the temperature goes up). Is this again a problem of the mother/logic board?
I had recently serviced it since it was not booting properly, but except some permissions repaired, they did noit find anything wrong in the hard drive (which I have now substituted with a SSD) or other hardware.
thanks in advance for any help/suggestions
alessandraI think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
the funny behaviour of the trackpad/cursor still persists. any suggestion???
thanks again -
PLEASE HELP! Problems with Cisco WLAN and WPA encryption
I checked the threads and didn't see this posted. I have a Cisco WLAN card in my T42_2373_C88. It's a very unfortunate thing that this wireless LAN card/wireless config. utitlity doesn't support WPA encryption. I'm not entirely sure that it's the problem with the WLAN card, and the reason for this is that I initially set up a network through the Windows config. utility bypassing the IBM utility (which I can no longer do). I wasn't actually able to connect to my local network until I completely removed the profile for my home network in the access connections, only then was I able to connect (WPA-PSK (TKIP)). I saw some drivers available for my make and model on the lenovo.com driver site. I downloaded the drivers and went through device manager specifying the folder where the drivers were located and the drivers were not recognized by windows as valid drivers. Unless specifically told otherwise, I don't want to manually override and load these drivers. This is a business machine, and this specific wireless function is VERY critical.
Thankstry using URLConnection instead of HTTPConnection.
-
Would someone be able to explain to me the following issue with Iphoto?
I ordered 8 same calendars for my soccer team and received them fine. Although a couple of pictures on it are a little off (out of focus). I need to order two more of the same calendars but when I go thru the process ireceive an error message saying:
"Unable to to assemble calendar" There is a problem with the photo with the file name "(Null)" The full resolution version of this photo either cannot be located or is corrupt. Please replace this photo or delete it from your calendar.
How can I fine this "corrupt" photo? How did it go thru with the first batch of calendars but won't go thru now?
Thank you for your help.Apply the two fixes below in order as needed:
Fix #1
Launch iPhoto with the Command+Option keys held down and rebuild the library.
Since only one option can be run at a time start
with Option #4 and then #1 as needed.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
1 - download iPhoto Library Manager and launch.
2 - click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option.
4 - In the next window name the new library and select the location you want it to be placed.
5 - Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments. However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT -
I can not download quicktime 7.7.3 for windows vista. The error message says that there is a problem with the windows installer. Any clues?
The error message says that there is a problem with the windows installer.
What's the precise text of the message, please? (There's a few different ones I can think of that you might be getting.) -
I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.
Cannot see what files ? Music (synced music should appear in the iPod app), films/TV shows (Videos app), documents ... ?
-
I notice that my new IPad (3rd generation) will not stay connected to the power cord at all, I'm not exagerating, if I plug it in and browse the Internet without fail it will become unplugged and I will have to push the plug back in (Ba-beep). Ive actually grown to despise that sound when you plug your iPhone or iPad in because it reminds me of how much money I spent on something that PHYSICALLY will not charge while I'm using it.
I know the problem with it holding a charge while in use, I get it, the screen is amazing and it takes a lot to run the display, however, it is unacceptable to me that I can't even keep the thing plugged in while I'm using it. I can not even leave it on my Cal King bed overnight because I will wake up in the morning to find that the plug has been jiggled loose in a corner, so it's still attached but not making a connection thus not being charged.
I love the 4GLTE from Verizon and I love the iPad, but I'm actually using my 1st generation IPad while I am at home so I can leave my new $900 iPad on a table to charge free of incident so I can use the 4G while I'm away from wifi during the day. I have been getting more upset about this because I can not even use the Griffin extended cord to charge the iPad and be far from the plug because only the original apple sync/charge cord will have a better shot at staying in. Absolutely none of my non apple cables will stay in the iPad 3 while having it in my hands.
The plug is at an angle, unlike the first iPad, not sure about the iPad 2. Please let me know if they have same issue.
If anyone else is having this problem with the Gen 3 iPad please let me know because I'm tempted to do something about it with apple and I'm hoping that I just for some reason have a bad cable receiver or something and maybe I can get a replacement and enjoy the iPad as I had expected to. There is no reason why I should be even using my first iPad and I have friends that want to buy it but I am not selling it because I'm unable to sell it because I can't handle the new iPad while it's plugged in, that is ridiculous if it's a common issue so please let me know!Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
Thanks again! -
Having Problems With The Neo2 ? Read This!!!!
Hi,
i just bought a neo2 motherboard, with a p4 2,6 HT and 512 mb Kingston hyper ram ( 2 peaces of 256, else it won't use the dual bandwith :D)
In the beginning everything seemed fine, until i got some sudden reboots and other vague stuff. I read it could be the SB audigy messing things up. I removed the card and windows Xp pro runs fine now. no more sudden reboots or explorer not resonding crashes.
But, i still had problems with games crashing. I got reboots. After i set the "automatic reboot after crash" to false, i got blue screens or lock-ups in my games.
I wondered what it could be. Then i started to put my videocard ( a radeon 9700 pro 128 mb) in agp 4x mode instead of agp 8x! Now my games run without crashes, but benchmarks are not that high. 4780 marks with 3dmark 2003.
I think i will send msi and Ati a mail concerning this problem. I don't know if it is PSU related. Maybe the videocard demands a little more power in agp 8x mode.
Well, having probs with you're NEO2 ??
remove the sb Audigy and turn the agp back to 4 using smartgart ( it's located in you're display settings screen ).
First i tought it was a PSU related problem, because i swapped my 350 Watt enermax with a Q-tec 400 watt psu. The 400 watt PSU died while i was gaming. Maybe the enermax is the better PSU :D So, it could still be a PSU related problem. Maybe the agp 8x settings demands a lot more from you're psu. Anyway, i'll receive a 550 watt Antec PSU soon, so i can check this out....
Btw. I cant run the motherboard in anything better than "slow" mode. In all other modes Xp won't boot. I haven't tryed it since the AGP is at 4X, but i don't think it will matter.
Regards,
Welcome to the real world NEO :DOk.....
i raised the memory voltage setting in the bios from 2.65 to 2.8 and the agp voltage from 1.5 to 1.7
Everything seems fine, but games crash back to the desktop now without an error message or the either lockup.
Whatever i do, i can't make the mobo crash in anything but games!
Btw. the following message caught my attention, when i ran f1 2002 with directx 8.1. Since i have directx 9, i haven't seen it anymore. Maybe because the ati-drivers are made for directx 9....
// Watchdog Event Log File
LogType: Watchdog
Created: 2003-10-04 02:02:53
TimeZone: -60 - West-Europa (standaardtijd)
WindowsVersion: XP
EventType: 0xEA - Thread Stuck in Device Driver
// The driver for the display device got stuck in an infinite loop. This
// usually indicates a problem with the device itself or with the device
// driver programming the hardware incorrectly. Please check with your
// display device vendor for any driver updates.
ShutdownCount: 9
Shutdown: 0
EaRecovery: 1
EventCount: 2
BreakCount: 2
BugcheckTriggered: 1
DebuggerNotPresent: 1
DriverName: ati2dvag
EventFlag: 1
DeviceClass: Display
DeviceDescription: RADEON 9700 PRO
HardwareID: PCI\VEN_1002&DEV_4E44&SUBSYS_00021002&REV_00
Manufacturer: ATI Technologies Inc.
DriverFixedFileInfo: FEEF04BD 00010000 0006000E 000A18EA 0006000E 000A18EA 0000003F 00000008 00040004 00000003 00000004 00000000 00000000
DriverCompanyName: ATI Technologies Inc.
DriverFileDescription: ATI Radeon WindowsNT Display Driver
DriverFileVersion: 6.14.10.6378
DriverInternalName: ati2dvag.dll
DriverLegalCopyright: Copyright (C) 1998-2002 ATI Technologies Inc.
DriverOriginalFilename: ati2dvag.dll
DriverProductName: ATI Radeon Family
DriverProductVersion: 5.2.3790.2
I wish i had another videocard to test. My radeon 9700 pro is getting suspicious...
Regards,
The real world -
Is anyone having problems with the battery heating up and draining the power? Mine has been doing this for about 2 months now.
This is a major problem with Lollipop, but yo said it started 2 months ago. Several people have fixed problem by removing FaceBook And Face book messenger and then re loading the apps again. You might want to clear your cache before reloading. Not sure this is your problem, but worth a try. Good Luck
-
I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid contrast, colour, radius, high tonal width and low tonal width.
If anyone has any suggestions as to how to access this advanced section, I'd be most grateful.Hi David-
The advanced adjustments in the Highlights & Shadows tool were combined into the "Mid Contrast" slider in Aperture 3.3 and later. If you have any images in your library that were processed in a version of Aperture before 3.3, there will be an Upgrade button in the Highlights & Shadows tool in the upper right, and the controls you asked about under the Advanced section. Clicking the Upgrade button will re-render the photo using the new version of Highlights & Shadows, and the Advanced section will be replaced with the new Mid Contrast slider. With the new version from 3.3 you probably don't need the Advanced slider, but if you want to use the older version you can download it from this page:
http://www.apertureexpert.com/tips/2012/6/12/reclaim-the-legacy-highlights-shado ws-adjustment-in-aperture.html -
I can send but cannot recieve email
This is the messege I am gewtting:
There may be a problem with the mail server or network. Verify the settings for account “MobileMe” or try again.
The server returned the error: Mail was unable to log in to the IMAP server “p02-imap.mail.me.com” using “Password” authentication. Verify that your account settings are correct.
The server returned the error: Service temporarily unavailableAlso if I go to system preferences accounts and re-enter the password it fixes the glitch sometimes.
-
Problems with the O2 blackberry data package on my Curve 3G.
I have already informed O2 about this but they claim that I should be used the blackberry support services, but nothing there helps me!
I got my Blackberry Curve 3G on September 9th this year and I put on the Blackberry Data Package bolt-on onto my phone on September 16th. I then received a text to say they've taken £5 from my credit and it will be up and running in the next 24 hours. Its now September 19th and my BBM is not working at all and I am extremely upset with the services and behaviour I have received from both O2 and Blackberry.
Is there any way you can help? If this fails, I shall be forced to go back to the shop from where I got my Blackberry from and ask for their help.
Many thanks, Jade.Can a bubble whistle Problems with the O2 blackberry data package on my Curve 3G.? The seat matures in your oar. The lad ices the pursuing method inside a resident. A judge spins against the vendor! The rose wows the hello.
filipina heart -
Many problems with the 'Export to Text' (.txt) in CR Xi
Hi,
I have listed many problems with the 'Export to Text' (.txt) function of CR Xi.
These problems are related to this export format only (meaning everything works fine in the Viewer or in the 'Export to PDF')...
- Multi-columns layout do not export as Multi-column (export only a one column);
- Numeric values with parenthesis for negative values or with a fix currency sign at the leftmost position are not exported correctly;
- Fields having a Suppress formula which is "WhilePrintingRecords" do not appears when exported;
- Fields with 'Suppress double value' checked are not always suppressed when exported to Text.
- 'Keep Group Together' flag is not working.
- 'Reset Page Number After' simply does not works when exported to text;
- 'Keep object together' on TextBox/Section is not working.
- Whenever a group is ending on the last line of a page, the the following page as the same Group header as the previous group with no records until the page is filled, then the PageBreak and PageHeader is missing but the records of the following group appears.
I would like to know what is the status of the 'Export to Text' function (is it a deprecated function not supported anymore???).
If still supported, when will these bugs be fixed???
ThanksHi Rene
Export to Text is supported till date. Crystal Reports 2008 also supports this with Keep together working however when I tried with format with multiple columns, it didnot show up in the exported text file.
Regards
Sourashree -
When going to update it says there is a billing problem with the previous purchase when I go to update it still won't let me download and all the info is correct. How do I fix this?
You have to email iTunes Store Support about this issue now. You can get started here. Change the country in the upper right if necessary.
https://ssl.apple.com/emea/support/itunes/contact.html -
Since updating to Firefox 4.0.1 I have a problem with the website shortcuts I have on on desktop.
<blockquote>Locking duplicate thread.<br>
Please continue here: [/questions/821825]</blockquote><br>
Since updating to Firefox 4.0.1 I have a problem with the website shortcuts I have on on desktop. I have a few of these shortcut to website I use a lot. When I click on the short I get the message "windows cannot find [then the web address] make sure you typed the name correctly, then try again. To search for a file, click the Start button, and then click Search." I tried deleting the shortcut and setting it up again but still get the message.Try to redo the default browser and make another browser like IE the default browser and then let Firefox do it again.
See:
* http://kb.mozillazine.org/Default_browser
* [[Setting Firefox as the default browser does not work]]
Maybe you are looking for
-
I've made a gallery in adobe bridge. Is there any way to put it into my iWeb website?
-
Unable to connect to dedicated game server on own ...
I run an rfactor2 game server on a separate machine on my home network. You join the server by clicking on a join button after selecting the server you wish to connect to in the server list. My server is listed, but I am unable to connect to it, the
-
IMovie displaying incorrect and mixed up pictures
I am currently creating a project that consists of a number of still frames. Unfortunately, when I insert a picture whether from finder or iPhoto, the incorrect picture is often inserted. How can I fix this?
-
There is any different between oracle 8i and 9i. recently we upgraded from 8i to 9i after that the applications are working very fast. anybody know what is the reason. Thank, Raghu.K
-
JVM Crashes Sporadically with ORA-24550 while Running Tomcat Web App
We have experienced a problem that has been troubling us for some time now. Our website goes down sporadically as a result of a JVM crash. The Tomcat catalina.out log reads as follows: # A fatal error has been detected by the Java Runtime Environment