Problem with the XI-Audit log entries in the table "XI_AF_MSG_AUDIT"

Hi,
I have an async-szenarios for PO:
We send Idoc's from SAP ERP to a WebService via SOAP. And we take Ack's. We use Integrationsprocess with deadline block to catche the errors after the retrying (three times) and to send they via e-mail.
Our problem is, the number of the audit logs in the table "XI_AF_MSG_AUDIT":
In the RTW only we see one audit log (with three retries) in an error case. But in the table XI_AF_MSG_AUDIT there are about 76 entries for the same audit log in the error case and about 20 entries in the case of the succuessfull processing.
This number of the entries in the table causes problem with the size of the redo log file and delete job of cours the large size of the table and therefore problem on the data base. The table can not be controlled. The delete job can not run and cancels every time due this redo log problems
What can cause that?
How can it be prevented, that so much entries are not be made in the table "XI_AF_MSG_AUDIT".
Best regards
Gueltekin

Hi Gueltekin,
I am only aware of the general property auditLogEnabled of J2EE Engine Service SAP XI AF Core, which controls in general (default = true) that entries in the AF Message Audit log are written at all.
(see [http://help.sap.com/saphelp_nw70/helpdata/en/5c/22ee41c334c717e10000000a155106/frameset.htm|http://help.sap.com/saphelp_nw70/helpdata/en/5c/22ee41c334c717e10000000a155106/frameset.htm])
I assume that your scenarios in the error case is sending up to three messages and for each message the number of audit log infos are created. You might want to check the detailed entries in the log and see from where they are comming, you might use customer modules etc. as well.
Best regards,
Silvia

Similar Messages

Each Document in Audit Log entry

Hi,
There is document library of name testdoclib in the site.
There are three files under the document library with names file1,.file2 and file3.
Users are downloading/viewing only file1,file2 files alone.
Now in the audit log entries,will i be able to view file3 entry as well?
In the audit log,will the entries be of files which are viewed/downloaded by the users?
Please share inputs on the same.
Regards,
Sudheer
Thanks & Regards, Sudheer

Hi Sudheer,
The log entries are captured for viewing, downloading or opening the document only or checked out or check-in. In your scenario, file3 entry will not be there until and unless any of the above mentioned actions happened.
Please refer to the following article.
https://support.office.microsoft.com/en-us/article/View-audit-log-reports-4293e8d5-4e7d-4201-b8ac-c8e63a100131?CorrelationId=d11e5086-013b-4416-a066-df51f22ff6fe&ui=en-US&rs=en-US&ad=US
Please don't forget to mark it as answered, if your problem resolved or helpful.

Problem with Inventory stock audit Report in other currency

Hi I have a problem with Inventory stock audit, the SBO show me the report in local currency, and I have to obtain that report in other currency, I was working with OINM table, but I don't know how obtain the report

Alberto,
Other currency information is available at the document row level and in the Journal Entries.
What you could do is join the OINM with the associated document and let the foriegn currency value.
OINM.TransType = ObjType (marketing document)
OINM.BASE_REF .......Document Ref
OINM.DocLineNum ......LineNum
Suda

Trying to configure syslog process,to write the database audit logs

Folks,
Running Oracle 10g R2 on Sun Solaris v 10.
I am trying to configure my database environment, so it will write all the database audit logs to a location, where Oracle userid on unix cannot modify/delete it.
To accomplish my goal, so far I have done the following:
I have set the following parameter with these values
audit_file_dest /flood/u01/app/oracle/product/10.2.0/db_1/rdbms/audit
audit_sys_operations TRUE
audit_trail OS
Also I asked my system administrator , to make an entry in the syslog.conf file at location /etc
He made the following entry
local3.notice /var/log/oraaudit.log
and restarted the syslog process
I also made the following entry
alter system set audit_syslog_level='LOCAL3.NOTICE' scope=spfile and bounced the database.
But after starting the database, i will don't see any oraaudit.log file at the location /var/log
Any help will be much appreciated.
Regards
Ashish

Hello Srini,
I mentioned in my posting , that I already set AUDIT_SYSLOG_LEVEL=LEVEL3.NOTICE value.
Also the permission on /var/log is such the Oracle unix userid cannot write to it and that is what I want. Since if Oracle userid can write, it can modify/delete the audit log also , which we are trying to prevent.
Thanks
Ashish

My IPad cannot download live Tv from skygo. I have no problem with my lap top so I assume the broad band is okay. Can anybody suggest why the live streaming will not work on my iPad one.

My IPad cannot download live Tv from skygo. I have no problem with my lap top so I assume the broad band is okay. Can anybody suggest why the live streaming will not work on my iPad .

Are you using the Sky Go app to try and watch it ? If so are you logged in with your Sky account ?
If you are using the app then you could try closing the app completely and see if it works when you re-open it : from the home screen (i.e. not with Sky Go 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Sky Go app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work then you could try a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Strange problem with SQLPLUS when client and server on the same box

Hi,
I have the problem with SQLPLUS when clinet and server on the same machine.
With client and server on the same machine i am running the command
sqlplus -l username/password@connect_identifier as SYSDBA.
With this command, even if you pass in wrong username or wrong password or both as wrong you can able to connect to database and execute queries.
Once Connect_identifier is correct and trying to log in as SYSDBA ,sqlplus will log in to DB with any username and password.
How to get rid of this behaviour. Is there any way to do this.
I am running this command by creating a process in C#
Edited by: user11000236 on Jun 16, 2009 10:31 AM

user11000236 wrote:
Thanks for the info.
How does Oracle/SQLPLUS allows any username or password to log in to DB with SYSDBA Privillages? What is the concept behind this.?
This is explainted in the above mentioned link:
Operating system authentication takes precedence over password file authentication. If you meet the requirements for operating system authentication, then even if you use a password file, you will be authenticated by operating system authentication.

Exchange 2013 SP1 - The attempt to search the administrator audit log failed.

During migration process from Exchange 2010 to 2013, after moving Arbitration mailbox from Exchange 2010 database to Exchange 2013 SP1 database, cmdlet Search-AdminAuditLog fails with following error.
The attempt to search the administrator audit log failed. Please try again later.
+ CategoryInfo : NotSpecified: (:) [Search-AdminAuditLog], AdminAuditLogSearchException
+ FullyQualifiedErrorId : [Server=EX2013,RequestId=517873e3-a623-4363-bfdc-e5aa23595c33,TimeStamp=29. 4. 2014
8:38:37] [FailureCategory=Cmdlet-AdminAuditLogSearchException] 2774D0CF,Microsoft.Exchange.Management.SystemConfig
urationTasks.SearchAdminAuditLog
+ PSComputerName : ex2013.domainname.local

Hi,
First, please make sure the Microsoft Exchange Search and the Microsoft Exchange Search Host Controller service are running and please run the get-mailbox -arbitration cmdlet to check the result.
Besides, please check the properties of the DiscoverySearchMailbox and verify that the homeMDB attribute is set to a mounted database.
If the steps above don't work, please try to re-create a new Discovery System Mailbox to check the result. You can refer to the following article.
Re-Create the Discovery System Mailbox
http://technet.microsoft.com/en-gb/library/gg588318(v=exchg.150).aspx
Best regards,
Belinda
Belinda Ma
TechNet Community Support

Remove a sleep log entry from the Lifelog

Is it possible to somehow remove a sleep log entry from the Lifelog?
I have an incorrect entry messing up my average value so I would like to get rid of it.
Solved!
Go to Solution.

It is possible to remove a single sleep activity. You scroll in the timeline to the activity you like to remove, then press the avatar while it’s sleeping. You will get a pop-up with sleep details for this specific sleep activity, press the trash can symbol and remove this activity.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Set to Upload Audit Log Entries into particular Library Programatically

Hi,
We got a requirement where need to set the Library to which the Audit Log needs to store.
By default in OOB, we have option as Browse and Set the document Library for Auditing any Site/Web/List. But in SPAudit class we couldn't find any related Methods/Properties to which we can set where this Audit Log entry should need to happen.
Could anyone help us asap.
Dinesh Pulugundla, Microsoft Certified Technology Specialist.

I don't know if that functionality is available programatically. My guess is SharePoint uses SPAudit.GetItems() or the SPAuditQuery class to query the
events and outputs as a Excel (CSV) file to the library you specify.
You could try recreating this process in your code.
Jason Warren
Habanero Consulting Group
habaneroconsulting.com/Insights
@jaspnwarren

I am having problems with creating my apple id. On the phone it is advising me that the ID is not created and then when i do it online it says that it has been created. Can you advise me on what to do please?

I am having problems with creating my apple id. On the phone it is advising me that the ID is not created and then when i do it online it says that it has been created. Can you advise me on what to do please?

Apple ID FAQ http://support.apple.com/kb/HE37

Has anyone in this Forum had problems with installing and running Adobe apps on the new MacPro?

Has anyone in this Forum had problems with installing and running Adobe apps on the new MacPro?
I have been trying to install Photoshop CS6 & CC and Acrobat Pro XI on my Mac Pro (late 2013). I keep getting a 'configuration' error message and wondered if the problem was wide spread.
TIA,
Jerry

Thanks, Martin.
Good to hear someone has had success. The lack of it here is frustrating and depressing.
Thanks again,
Jerry

Hello, I have a problem with my mac book pro after running the battery dead on a game. The display has shrunk leaving two black margins on either side. What to do ?

Hello, I have a problem with my mac book pro after running the battery dead on a game. The display has shrunk leaving two black margins on either side. What to do ?

Go to System Preferences>Displays and set the resolution to "Best for this computer" (or something to that effect).
Clinton

I have set up two users, one for myself and one for children. The computer automatically logs in for the children with no password required. When the children go to spotlight and type in a search criteria all of my files show up. How do I prevent this?

I have set up two users, one for myself and one for children. The computer automatically logs in for the children with no password required. When the children go to spotlight and type in a search criteria all of my files show and open up. How do I prevent this?

Log in to your account, and move all your files to your home folder. No other users should be able to access them there and they won't show up with a Spotlight search.
Make sure your kids' account(s) do not have admin privileges.

I have a problem with running an EXE file on win2000, the Lab View is 5.1 and I do not know if it is 16 bit...

I have a problem with running an EXE file on win2000, the Lab View is 5.1 and I do not know if it is 16 bit...what should I do?

Hi Arika,
The drivers that you need to install to make your executable work depends on what your executable is doing. To get started, you need to have the LabVIEW Run-Time Engine installed on your target machine (the Win2000 machine you are planning to use) in order to run your executable. Next, you need to determine what drivers your executable uses, if any. For example, if you are using GPIB instrument control, you will need to install the NI-488 drivers on your target machine. If you are performing data acquisition, you will need to install NI-DAQ drivers. If you are doing image acquistion, you will need to install NI-IMAQ drivers.
All these drivers are available for downloading on ni.com. To get the drivers, go to ht
tp://www.ni.com/support , click on the link that takes you to Drivers and Updates (under Option 3), and click on the links to get to the driver(s) you need. For example, if you need the LabVIEW 5.1.1 Run-Time engine, click on the All Drivers and Updates by Application link on the main page (http://www.ni.com/softlib.nsf/). Then click on the LabVIEW link, Windows 2000, Run Time Engine, and then you will see the link to get to the page to download the LabVIEW 5.1.1 Run-Time Engine.
I hope this information helps.
Best Regards,
Wilbur Shen
National Instruments

Apple tv is giving me a meesage that says... There is a billing problem with a previous purchase. Go to the iTunes Store on your computer and click Purchase History to resolve problem. I have gone to my purchase history but can't seem to fix this issue.

Apple tv is giving me a meesage that says... There is a billing problem with a previous purchase. Go to the iTunes Store on your computer and click Purchase History to resolve problem. I have gone to my purchase history but can't seem to fix this issue.

You can contact the iTunes Store Customer Service department at no charge using the form on their Support page (select the category and subcategory closest to the issue you're reporting and you'll find an "Email Us" button) and explain your problem to them.
Copied from Varjak Paw in :https://discussions.apple.com/thread/2598671

Problem with the XI-Audit log entries in the table "XI_AF_MSG_AUDIT"

Similar Messages

Maybe you are looking for