Problems building a stand alone application with LV 8.6.1.

I'm having problems building  a stand alone application with LV8.6.1. I'm using a USB- 6008 DAQ and USB-6501 Digital device in the application. I already have an simple executable on the machine so the Run time Engine is already installed.  For the USB DAQ device, I assume I need to include the DAQmx8.8 as one of the installers. When I attempt to build the application, I'm prompted for several disk, one being a distribuition disk 1. I have the installation disk for the developer package. I did not  see a distribuiton disk as one of the installation disks. When I insert disk 1 I get an error that another application is trying to run. Could someone tell me which installers I need to include and where do I find the "distributor" disk.
Thank you,

are you building installer for the first time on this PC?...It usually asks for the drivers CDs and some toolkits if required.
you just need to use drivers CDs (comes with LabVIEW) from which you installed on this PC. If you have ever upgraded drivers, then you have to use the latest CDs only.......
another issue may be ...when u insert the driver disk, it has autorun, it will launch drivers installation wizard....close that and then try to build distribution......... 
Message Edited by Anil Reddy on 09-25-2009 01:22 PM
Anil Punnam
CLD
LV 2012, TestStand 4.2..........

Similar Messages

  • Stand-Alone application with LabView 7.0 getting error can't find DAQmx clear task.vi

    I have attempted to create a stand alone vi with the Build Application or Shared Library(dll) in LabVeiw 7.0
    When I put it on another PC to test it I get the error "can't find DAQmx clear task.vi"
    the other PC has Labview 7.0 and DAQmx 8.1 also.
    I believe my problem is in the source tab where you are supposed to add support and dynamic vi's I have search the forums and Ni's data base and have not found a solution.
    Solved!
    Go to Solution.

    Hi LabTech09,
    When you run the executable on the other computer is when you get this error?  Do you have the exact same versions of LabVIEW and DAQmx on both computers?  Does the dialog allow you to navigate to the DAQmx clear task.vi?  If so, you can find these VIs in C:\Program Files\National Instruments\LabVIEW 7.0\vi.lib\DAQmx\configure\task.llb.  Does the executable work on the development machine (the machine it was compiled on)?
    Regards,
    Jim Schwartz

  • Stand alone application with VISA

    Hello,
     I build a stand alone installer application from my VI using LV 7.1 VI which contains some VISA serial communications with a standard RS232 port.  In build application wizard settings I checked the Serial Port Suport in Advanced settings in Installer .When I installed this stand-alone app on a new PC without LV installed the communication didn´t work: Error -1073807298 - Could not perform operation because of I/O error.
    I don't know if I have to install something else on the target machine. I have seen some topics in discussion forum about the VISA run machine. I imagined it would be included in the installation I had created. If someone could help me I would thank.
    Celia

    Hi Celia,
    You might check to make sure that the VISA Resource Name you are providing in your application is the same as the name the new machine is using.  If you build the application and it is looking for a specific resource that does not exist on the new machine, you might see an error similar to this one.
    Donovan

  • Problem building WLI 10.2 applications with exported ant build files

    Hello,
    I'm trying to build a WLI application without the workshop IDE. To accomplish this I exported ant build files, workspace.xml and the workspace libraries.
    When I run the build, I get the following (part of the) stacktrace:
    [apt] Compiling 8 source files to C:\development\BuildOFOP\workspace\ContractAccountService-Web\build\classes
    [apt] warning: Annotation types without processors: [com.bea.wli.transform.XQueryTransform.SchemaValidate]
    [apt] java.io.FileNotFoundException: File not found
    [apt] at java.util.zip.ZipFile.open(Native Method)
    [apt] at java.util.zip.ZipFile.<init>(ZipFile.java:117)
    [apt] at java.util.zip.ZipFile.<init>(ZipFile.java:76)
    [apt] at com.bea.wli.bpm.bean.codegen.JarHelper.unJar(JarHelper.java:31)
    [apt] at com.bea.wli.bpm.bean.codegen.ResourceConfig.configureEjbJars(ResourceConfig.java:749)
    [apt] at com.bea.wli.bpm.bean.codegen.ResourceConfig.configureEjbJars(ResourceConfig.java:704)
    [apt] at com.bea.wli.bpm.compiler.JpdAnnotationProcessor.generateBeans(JpdAnnotationProcessor.java:343)
    [apt] at com.bea.wli.bpm.compiler.JpdAnnotationProcessor.generate(JpdAnnotationProcessor.java:56)
    [apt] at com.bea.wli.knex.ap.TwoPhaseAnnotationProcessor.process(TwoPhaseAnnotationProcessor.java:103)
    [apt] at com.sun.mirror.apt.AnnotationProcessors$CompositeAnnotationProcessor.process(AnnotationProcessors.java:60)
    [apt] at com.sun.tools.apt.comp.Apt.main(Apt.java:454)
    [apt] at com.sun.tools.apt.main.JavaCompiler.compile(JavaCompiler.java:448)
    [apt] at com.sun.tools.apt.main.Main.compile(Main.java:1075)
    [apt] at com.sun.tools.apt.main.Main.compile(Main.java:938)
    [apt] at com.sun.tools.apt.Main.processing(Main.java:95)
    [apt] at com.sun.tools.apt.Main.process(Main.java:43)
    [apt] at com.sun.tools.apt.Main.main(Main.java:34)
         [apt] Problem encountered during annotation processing;
    [apt] see stacktrace below for more information.
    [apt] java.lang.IllegalStateException: Error customizing project beans; could not locate weblogic home null
    [apt] at com.bea.wli.bpm.bean.codegen.ResourceConfig.configureEjbJars(ResourceConfig.java:769)
    [apt] at com.bea.wli.bpm.bean.codegen.ResourceConfig.configureEjbJars(ResourceConfig.java:704)
    [apt] at com.bea.wli.bpm.compiler.JpdAnnotationProcessor.generateBeans(JpdAnnotationProcessor.java:343)
    [apt] at com.bea.wli.bpm.compiler.JpdAnnotationProcessor.generate(JpdAnnotationProcessor.java:56)
    [apt] at com.bea.wli.knex.ap.TwoPhaseAnnotationProcessor.process(TwoPhaseAnnotationProcessor.java:103)
    [apt] at com.sun.mirror.apt.AnnotationProcessors$CompositeAnnotationProcessor.process(AnnotationProcessors.java:60)
    [apt] at com.sun.tools.apt.comp.Apt.main(Apt.java:454)
    [apt] at com.sun.tools.apt.main.JavaCompiler.compile(JavaCompiler.java:448)
    [apt] at com.sun.tools.apt.main.Main.compile(Main.java:1075)
    [apt] at com.sun.tools.apt.main.Main.compile(Main.java:938)
    [apt] at com.sun.tools.apt.Main.processing(Main.java:95)
    [apt] at com.sun.tools.apt.Main.process(Main.java:43)
    [apt] at com.sun.tools.apt.Main.main(Main.java:34)
    [apt] Caused by: java.io.FileNotFoundException: File not found
    [apt] at java.util.zip.ZipFile.open(Native Method)
    [apt] at java.util.zip.ZipFile.<init>(ZipFile.java:117)
    [apt] at java.util.zip.ZipFile.<init>(ZipFile.java:76)
    [apt] at com.bea.wli.bpm.bean.codegen.JarHelper.unJar(JarHelper.java:31)
    [apt] at com.bea.wli.bpm.bean.codegen.ResourceConfig.configureEjbJars(ResourceConfig.java:749)
    [apt] ... 12 more
    Anyone got any idea what might be the problem here? I did followed the BEA instructions for exporting the ant build files.
    Grtz, Jaco

    Hi
    This is a known issue addressed by CR205204
    As you said, IBM actually does not have rt.jar in its JDK - they have moved contents of rt.jar into various jars.
    IBM is not using org/apache/crimson/tree/ in their JDK at all.So the error shows up in the end of build even if it succeeds
    You may need to add crimson.jar to wlwBuild classpath, since it is not part of IBMs JDK.
    Note: the build will work even w/o crimson.jar giving a non build related IDE exception in the very end.
    Thanks
    Vimala

  • Stand-alone application generates error with function 'Ramp Pattern' (bug in application builder?)

    Hello,
    in my program a main.vi links to a sub-VI via 'open VI reference' and 'invoke node'. In this sub-VI the function 'Ramp Pattern' is used. The program itself runs normally, but if I build a stand-alone application using application builder I get an error message 'error 1003 occurred ..'. I believe this error is directly related to the build specifications which are as follows: the main.vi is referenced in a main build specification, the sub-VI in its own specification where the target is a LLB.
    I appended an example-program that exhibits the error (when executing 'Application.exe' and pressing 'calculate ramp'). The error does not occur when disabling the 'ramp pattern' function and rebuilding the application.
    I would rate this to be a bug in the application builder and would appreciate any help on how to solve this problem. However, due to the structure of the whole program the sub-VI has to remain in its own LLB.
    Attachments:
    RampPattern.zip ‏198 KB

    There can be reasons why a VI might appear broken when loaded from an executable. For example, if you have different versions of the same VI or enum that differ in such a way as to break the calling VI, that can cause a broken arrow when loaded from the executable. If you have DLLs being called and the runtime engine can't find the DLL, that can cause a broken arrow that you might not see otherwise. Finally, there is a bug related to a VI appearing broken when its not.
    Mike...
    Certified Professional Instructor
    Certified LabVIEW Architect
    LabVIEW Champion
    "... after all, He's not a tame lion..."
    Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

  • Building a stand-alone AppleScript Studio application

    I’m taking a crack at building my first stand-alone application with AppleScript Studio. After many attempts to locate the needed “build” information in the various documentation resources I’m still pretty much poking around in the dark ...
    My application runs fine in the Xcode IDE. No problems. The application that Xcode saves in the project’s Debug folder runs too, (well, on the computer I developed it on) even if I move it out of its folder ...
    However, the app. doesn’t run on other macs. When double-clicked and it sorta fizzles without ever opening — wondering if the debug version relies on some resources within the project. I've installed it on a PowerBook and iBook, both running Mac OS 10.4
    I tried Build/Release. This also produced an application (in the Build/Release folder) which when failing to launch and causes the OS to burp, “You cannot open the application “My First App” because it may be damaged or incomplete.” This app will not run on my development computer or other laptops (PowerBook and iBook.)
    Build/Release also invoked three Xcode compiler error messages that seem to indicate that I need to change the NIB settings:
    /usr/bin/ld: warning /Developer/SDKs/MacOSX10.3.9.sdk/System/Library/Frameworks/Cocoa.framework/Coco a cputype (18, architecture ppc) does not match cputype (7) for specified -arch flag: i386 (file not loaded)
    /usr/bin/ld: warning /Developer/SDKs/MacOSX10.3.9.sdk/System/Library/Frameworks/AppleScriptKit.frame work/AppleScriptKit cputype (18, architecture ppc) does not match cputype (7) for specified -arch flag: i386 (file not loaded)
    /usr/bin/ld: warning fat file: /usr/lib/gcc/i686-apple-darwin8/4.0.1/../../../libSystem.dylib does not contain an architecture that matches the specified -arch flag: i386 (file ignored)
    Also got this warning(?):
    /usr/bin/ld: Undefined symbols:
    __keymgr_dwarf2_registersections
    _cthread_initroutine
    _atexit
    _errno
    _exit
    mach_initroutine
    _ASKInitialize
    _NSApplicationMain
    collect2: ld returned 1 exit status
    Also tried Clean All. Same result.
    I'm sure there's a simple step ... which I will remember well, 'cause I'm learning it the hard way.
    John

    However, the app. doesn’t run on other macs. When
    double-clicked and it sorta fizzles without ever
    opening — wondering if the debug version relies on
    some resources within the project. I've installed it
    on a PowerBook and iBook, both running Mac OS 10.4
    You're right. You can't move a debug version of the app to another computer unless you copy the entire project folder. The debug version of the app requires access to other by-products of the build process in order to run.
    Build/Release also invoked three Xcode compiler error
    messages that seem to indicate that I need to change
    the NIB settings:
    The following errors are not related to your NIB file. They indicate you're trying to link against the 10.3.9 frameworks on an intel CPU. The 10.3.9 frameworks are PPC only.
    /usr/bin/ld: warning
    /Developer/SDKs/MacOSX10.3.9.sdk/System/Library/Framew
    orks/Cocoa.framework/Cocoa cputype (18, architecture
    ppc) does not match cputype (7) for specified -arch
    flag: i386 (file not loaded)
    /usr/bin/ld: warning
    /Developer/SDKs/MacOSX10.3.9.sdk/System/Library/Framew
    orks/AppleScriptKit.framework/AppleScriptKit cputype
    (18, architecture ppc) does not match cputype (7) for
    specified -arch flag: i386 (file not loaded)
    /usr/bin/ld: warning fat file:
    /usr/lib/gcc/i686-apple-darwin8/4.0.1/../../../libSyst
    em.dylib does not contain an architecture that
    matches the specified -arch flag: i386 (file
    ignored)
    [snip]
    Take a look at the suggestions I made in this thread to make sure your project is set up to build a universal binary and to ensure that you're linking against the 10.4 universal frameworks.
    Steve

  • Stand alone application(.exe) : Error 7 occurred at Open File+.vi: Open File (error: L'erreur 7 s'est produite à : Open File+.vi:Open File)

    Dear group members - as i am trying to build a stand alone application , i ran into this problem : "Error 7 occurred at Open File+.vi: Open File" (L'erreur 7 s'est produite à : Open File+.vipen File)
    when i select continue i get this error message: "Error 7 occurred at open/create/replace file in Write spreadsheet string.vi->Write To Spreadsheet File (I64).vi->Mono Com Write ini.vi->mainVI2.vi""   (  "L'erreur 7 s'est produite à : Ouvrir/Créer/Remplacer un fichier dans Write Spreadsheet String.vi->Write To Spreadsheet File (I64).vi->Mono Com Write ini.vi->mainVI2.vi" )
    i didn't get what's the problem with this vi, i have no problem running my VIs  
    Can any one here help me out ? 
    here is the project : 
     

    Neither can I.  When I opened your Project, there were no VIs present on the top level.  The Build Spec refers to a Mainv12, which I finally found buried in the folder Interface 2, but when I tried to open it, there were multiple missing VIs.  I notice you have an Interface 2.llb -- is this the same as the VIs in the Interface 2 folder?  If so, try getting rid of the .llb (at least for the purpose of sharing your code in the Forum) and re-post your code.  As it stands, when I open your Project, virtually every entry is marked "Warning: has been deleted, etc."  The fact that so much is "missing" means that I can't easily see/understand MainV12, hence can't guess where the File Not Found error is arising.  Sorry.
    Bob Schor

  • Stand-Alone Application including ocx, dll and Word template folder

    Hi,
    I try to create an Stand-Alone Application with labview 2011. My problem is how i can include ocx and dll file in my executable to be run by others computers (the other computer don't have the dll and the ocx using in the application). My program use Word template who is in a folder. How i can integrated this Template folder in my executable folder.
    This is the first time I create an executable, so please help me -_-.
    Nki
    Solved!
    Go to Solution.

    Hi nki,
    To include the ocx and dll files you will need to build an executable for your VI and then create an installer for the additional files. I have linked 2 documents that will explain each of these steps. If you have any questions with this let me know.
    http://zone.ni.com/reference/en-XX/help/371361E-01/lvhowto/exe_ex/
    http://digital.ni.com/public.nsf/allkb/E09BA0E2F31D304F86256A640070058E?OpenDocument
    Patrick H | National Instruments | Software Engineer

  • How to include dll into a stand-alone application

    Hi, I wrote a vi to process images from my camera, and I want to build a stand-alone application(exe), so I can share the application with my friends. I just do as wht's in  the Labview help, but when I run the exe file in other PC, it  tells me I haven't nivision.dll etc. My question is how to find out the dll files in my vi and include these files in the stand-alone application?  

    To be honest I am not sure. Its been a while since have used the vision run-time engine. Before I installed it on the target computer. I ddn't include it with my application build.
    Take a look at this http://digital.ni.com/public.nsf/allkb/1A9A18AA574ABEDF86256F780062C240 it might help. Also look at the documentation supplied with the vision deployment license.
    David

  • Is it possible to have a user interface in a stand alone application without having LV

    Hi!
    I want to know if it's possible to build a stand-alone application in order to avoid purchasing LV and at the same time having a user interface to display data?
    I really want to know what are the advantages of the stand-alone applications and what are their limits of use?
    Thank u

    If you have the application builder (included in LabVIEW professional and above) you can make a LabVIEW application that can be distributed and run on machines that don't have LabVIEW installed. If you only have LabVIEW full, you can purchase it seperately.
    The target machine requires the LabVIEW runtime, which is freely downloadable from NI, or can be included with the installer of your application.
    Please have a look at the datasheet: http://www.ni.com/pdf/products/us/4msw55.pdf
    If still have more specific questions not mentioned in the above link, please ask.  
    Message Edited by altenbach on 10-01-2007 01:01 AM
    LabVIEW Champion . Do more with less code and in less time .

  • AIRHelp stand-alone application takes a while to launch

    Hello,
    An AIRHelp stand-alone application with about 50 topics is taking about 20 seconds to launch and sometimes the navigation from one topic to another is delayed.  I removed videos and external links and it runs faster and there are no broken links in the RoboHelp files; however, this sped the output application a bit, but it is still slow.  Does anyone have any suggestions on how this can be made faster? Are there any formatting issues that would slow an AIRHelp application down when generated?
    Thanks,
    Jason

    Have you optimized youe graphics? Meaning .jpg at perhaps 50% compression. PNGs are 10X .jpg size on average.

  • I have trouble in building stand-alone application, "you must intall Labview run-time engine on any computer on which you want to run this application"

    I have installed the LabVIEW 7.0 run time engine and checked all in the advanced setup on the installer setup slide. but I still get such a message saying that the target computer needs to have LabVIEW 7.0 run-time engine. What I want is a real stand-alone application even without having labview ... I used to think that's due to my program contains MATLAB nodes. But this is not true, since even without Matlab, it's still wrong. Please help, thanks!!!

    As was stated elsewhere, you have the option of building the runtime engine into your application when you build it. However, you can also create a "runtime engine application" by simply opening the application builder and doing a build without adding any source code files. The result is a small program (named lvrt.exe) that can run any LabVIEW code--whether or not its built into an executable.
    Such an application can be helpful if you are wanting to install several LV-based applications on the same computer in that it reduces the amount of redundant code on disk. All you have to do is make sure that Windows on the target computer associates the llb and vi file extensions with the runtime engine program.
    It can also be helpful during testing to run test code that isn't built into an executable.
    Mike...
    Certified Professional Instructor
    Certified LabVIEW Architect
    LabVIEW Champion
    "... after all, He's not a tame lion..."
    Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

  • How build stand alone application without labview

    I have main vi and contain the sub vi i need build stand alone application without labview
    how build stand alone application without labview?
    thank and regard

    I assume that the poster means to run this on a computer without the development environment installed.  That is what the app builder is for. Review Altenbach's post.  This being said, there will need to be a runtime engine installed on the target PC. You can 'bundle' that with your build application and install it together, although I usually prefer Not to do that, and make that a seperate step because it is rather large, and if the target already has it, then it is wasted space.  Speaking of run time engine, I have seen negative reactions to it by my customers, but after sitting down and explaining that, with few exceptions, every application requires a run time engine. It is just that some are bundled with windows, or installed through windows update.  Once explained, it usually quiets the opposition. [Paul steps off soap box now]
    Paul <--Always Learning!!!
    sense and simplicity.
    Browse my sample VIs?

  • How to use Preloader with stand-alone application in Eclipse? Thank you.

    My IDE is eclipse and my project is a stand-alone application(pure CS architecture with OSGI framework).
    How to use Preloader thus the preloader would be started before my main Application and hid later?
    I found some code in http://docs.oracle.com/javafx/2/deployment/preloaders.htm#BABGGDJG
    but I still don't know how to deploy the Preloader with my startup Application in OSGI framework.
    I give some code of my startup application below:
    public class MyPrjMain extends Application
        private static Stage primaryStage;
         public void start(final Stage stage)
            throws BusinessException
            primaryStage = stage;
            init(primaryStage);
            primaryStage.show();
    }Thanks very much, everybody.
    Edited by: Slash Wang on 2013-2-27 下午5:36

    Your question has already been answered on StackOverflow:
    http://stackoverflow.com/questions/15126210/how-to-use-javafx-preloader-with-stand-alone-application-in-eclipse/15148611

  • How to use matlab codes in a stand alone application without matlab license?

    Hi,
    I am not an expert in programming and i don't know about C++, i have a program using matlab codes and now i want to transfer it to a computer without matlab license. I've read something about using DLL, but i think i have to know C++ programming  to wrtie "WRAPPER" and add some lines to the program, now transformed in C++.
    I just would llike to know that really isn't any other way to integrate matlab for a stand-alone application? i read somethings in Matlab help about using COM (Common Object Model ) but i am not sure that labview works with it, and also about runtime engine and "mglinstaller.exe".
    my labview version is 8, matlab is 2006, and the real problem is using matlab codes in another computer without matlab license.
    Thanks
    Amir

    Hello Amir,
    There is a MatLab script node in the LabVIEW function palette (see screenshot of the help topic) but as you can see this structure is not in the "Base LabVIEW", you might need to purchase the FDS (Full Developpment System) or the PDS (Professionnal Developpment System) of LabVIEW...
    Do you know which one you have ?
    Hope this helps
    Message Edité par TiTou le 11-24-2006 06:38 PM
    When my feet touch the ground each morning the devil thinks "bloody hell... He's up again!"
    Attachments:
    mlab.png ‏71 KB

Maybe you are looking for