Problems connecting airport express a1264 to bt homehub 3 router in bridge mode

I cant seem to get this to work. When i had sky i could bridge my airport express to their router and create a new network so i could extend the network upstairs using another airport express.
I just cant seem to get it to work with the bt homehub 3. can anyone help?

Althrough have no experience of the device this Netgear extender has apparently been used with Home Hub (Ver 2) with success.
Netgear WN1000RP
Every "free Netgear router" i have received from ISPs in the past has been slung in a large box and forgotten.
Much prefer Cisco or Apple with the ISP device simply being a modem.

Similar Messages

Unexpected error when connecting Airport Express A1264 to Airport Utility 6.3.1

My current wireless setup is and has been the following: Phone Jack --> DSL modem ---> Airport Express via Ethernet cable
Off of that connection we've been able to wirelessly run our MacBook, Apple TV and iPhones for several years.
We recently left for vacation, so I unplugged everything (apparently a huge mistake). When we returned from vacation, the wireless connection was intermittent and kept being dropped.
If I connect the Ethernet cable directly from the modem into my MacBook the internet works fine.
I tried refreshing the Airport Express by unplugging it and cycling it through. It continued to drop.
By opening the Airport Utility, a firmware update was recommended. However, since that update the Airport Express isn't detected anymore.
I tried a hard reset and Utility finds the Airport Express under "Other Wifi Devices" but then, at the end of trying to "Join the Airport Express to the Network" I get an "Unexpected Error" message.
Airport Express Model Number: A1264
Airport Utility: 6.3.1
OS: 10.8.5
I am very frustrated and way out of my league here with understanding how this all works and what I can do to fix it. If anyone has any suggestions or expertise to offer, I would greatly appreciate it.
Thank you for your time,
Amanda

Hi AMM222,
"Unexpected Error" message with Mountain Lion and AirPort Utility 6.3.x. Hopefully this is just a matter of enabling IPv6.
AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
http://support.apple.com/kb/TS4597
This can happen if IPv6 has been disabled. To enable IPv6 for your network interface:
Choose Apple menu () > System Preferences, and then click Network.
If a lock icon appears in the lower-left corner, click it and enter your admin name and password to unlock the pane.
Click your network service (Wi-Fi or Ethernet) in the list, and then click Advanced.
Click the TCP/IP tab.
Choose Link-local only from the Configure IPv6 pop-up menu.
Click OK.
Click Apply.
The AirPort device should now appear in AirPort Utility.
Thank you for using Apple Support Communities.
Nubz

Problem connection Airport express Fritzbox 7360 lion

I cannot connect my airport express to stream music anymore sinds I installed my new Fritzbox 7360 and Lion.
what tot do?
Carin

HI Agnes,
To check your OS to see what version you are running. Click on the Closed Apple in the most upper left corner of your screen. Then scroll to About this Mac. a window will appear and will tell you some basic info. like what version OS you are running. If you want to know more about your computer then click on " more info. " button. A program called System Profiler will launch and give you all the info on your computer.
As for Airport you can find out what version you have in the System Profiler. Just toggle the Software triangle and click on software. this might take a minute or so depends on how many programs you have. then find Airport and then you will know what version you have.
Another way to find out what Airport version you are running is to launch/open the Airport Admin Utility app. you can find it in Applications folder>Utilities Folder>Airport Admin Utility. After it is open click on Airport Admin Utility in the most upper left corner of your screen just to the right of the closed apple. scroll to About Airport Admin Utility and click. a small window will appear and you will know what version you are running.
As for Firmware on your Airport Express, Airport Admin Utility needs to detect it before you can find out what version you are running. I have not tried to install the firmware update with out my Airport Admin Utility not detecting it. Not sure if it will work.
Ok I hope this helped...

Apple Airport Express: How To Change IP Address While in Bridge Mode

Hello, I have a Apple Airport Express router and it has been good for a few years. Just wondering how to change my public IP address. I am also in Bridge mode to a cisco router. Also I am on a Windows 8 computer and this is mainly what I want to change the ip for.

Power cycle the cable modem.. I presume that is what the cisco router is.. your modem.. if not tell us precise model and make of the modem.
The public IP is not changed by you.. it is changed by your ISP.. normally if you power cycle the modem on a dynamic system you will get a new IP.. if not call the ISP and request them to make a change.
It is never really necessary unless you got banned from a site.
I am on a Windows 8 computer and this is mainly what I want to change the ip for.
There is no logical link to needing a new public IP to being on a windows 8 computer.
Explain more about your problem.

Airport Extreme ethernet routing in Bridge Mode

i had(!) the following scenario Airport Extreme (5th Generation) .. via WAN connect to the modem, Ethernet to serval switches, WiFi acting as WDS Main
the WDS Slaves are 3 small Airport express and one Airport Extreme (1st Generation)
due a cabeling problem i had to move the WAN Modem .. and connected it to the 1st generation airport extreme created a Joined network (not WDS) enabled DHCP on the same device.
the new Airport extreme (5th generation) and the Airport Express joined the same network and running in bridge mode.
everything works just like before .. all networks parts can connect to each other, anywhere else including the internet.
exept of anything connected to the ethernet ports of the (now slaved) airport extreme (5th generation) anything connected there seems not to be routed at all ..
they have a physical connection (link show on the Airport and on the Switch. but there is zero data going trough ... no DHCP adresses assigned. manually assign a IP in the same network results in the same effect (can't even ping the directly connected Airport Extreme.
is this a Bug ?

oh ic ... thats why it worked before the other way arround ...
well does still not make any sense to me .. but you are 100% right ..
enabeling WDS on the Airport Extreme (1gen) and doing slave the Airport extreme (5 gen) works fine .. but the connection times are about 10 times slower than in a joined network.
which makes the whole show extremly slow ...
it takes some times 5 minutes and a million time clicking (assign new) to just get an IP adress ... even if the dhcp running on the same Airport where the client is connecting to ..
if the 5gen APE is WDS master .. and the 1gen is WDS Slave (my old setup) .. this problem is not existing ...
but then ican't connect the WAN modem to the slaved Airport since the slave is always bridged and the master requires internet connectivity trough the local Wan port
any idea to get arround this ?

Connecting airport express to zyxel modem

I connect to the internet via DSL using a Zyxel 660 HN DSL router. This modem is also the base station of my wireless network. I am now trying to connect my USB Printer (HP LaserJet 1320) to this wireless network using an Airport Express Base Station (Model A1264, 2008). I am able to set up the Airport Express Base Station by connecting it to my MacBookPro with a LAN-cable and using the Airport Utility (Version 6.1). The Airport Express Base Station is then in the proper operating mode (green light on), and my router detects it as one of the WLAN-clients. However, if I connect my printer with the USB cable to the Airport Express Base Station, my computer (which is connected to the WLAN as well) is unable to see the printer. Can anyone give some advice how to solve this problem?
As an aside, I also enabled AirPlay on the Airport Express Base Station, but iTunes on my MacBook is not showing the Speakers button at the bottom of the iTunes window.
Somehow, the Airport Extreme Base Station seems to be connected to the WLAN properly, but it is not recognized by other WLAN clients and its functionality cannot be used. Any help would be greatly appreciated!

51kevin wrote:
my airport router does not see my modem links 3008
I am going to guess.. you are talking about cable modem.. linksys DPC-3008
You plug express into the ethernet port of the modem.. setup the Express to dhcp for WAN.
Then you need to power cycle the cable modem to get rid of the previous connection.. whatever connected before the express will take the public IP and the modem will not release it until the lease is renewed.. to force that renewal a power cycle of the modem is required.. it can take up to 20min for the ISP equipment to give up the old MAC address and renew the lease.. Some ISP you will even need to phone up and ask them to reset the port.

Airport Express A1264 and WEP

Hey Gurus,
Not sure what the deal is or whether I am missing something. I am able to connect my airport express A1264 at my house to the wi-fi with no problems. But here at work, I am having trouble connecting the airport with the office wi-fi. There is no setting on the AX to set up with a WEP. Wep 16 and 32 bit are the only choices. Is there an update for the A1264? If so how?
TIA
paul

One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling the use of simple easy to remember WEP password rather than lengthy HEX keys. The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a non-Apple client and vice versa.
You may find the following Apple Support article helpful: AirPort, Time Capsule: Joining an encrypted wireless network

Can you use the Airport Express A1264 as an AP and a DHCP server at the same time?

Can you use the Airport Express A1264 as an Access Point and a DHCP server at the same time?
I would like to use it as a DHCP server and AP at the same time in my LAN (no internet, just local machines through a few switches). I was lead to belive this could be the case from a few networking friends that haven't been friendly enough to help me out setting it up.

I need it to act as a dLink/Cisco/Linksys/etc basic wifi router, in the fact that you can access it via wifi, and it will spit out DHCP addresses (192.168.1.xxx) to everything wired downstream of it.
I want to simultaniously provide a Wifi connection and a LAN connection at the same time
Thanks,
BRad

How to Connect Airport Express to Existing Wireless Network (Client Mode)

I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
So here's the situation:
Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
Do yourself a favor, toss that user manual aside and run these steps.
(Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
Some pointers:
- When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
- I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
<Edited by Moderator>

Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
Thanks

Can't connect Airport Express wirelessly to network so that AirTunes and internet are available simultaneously

I can't connect Airport Express wirelessly to network so that AirTunes and internet are available simultaneously. My old AE allowed this but can't make the new one work that way.

In your instructions, you say to use the same encryption type as the router has set up. well, I am using the WEP 64 bit encryption and the Airport Utility does not have this...it has 40 bit. Is this a problem, or do I have to be using a the same type of encrytion ?
WEP is available in either 40 or 104-bit, but is usually "advertised" as either 64- or 128-bit respectively. For example, 64-bit WEP uses a 40 bit key (also known as WEP-40), which is concatenated with a 24-bit initialization vector (IV) to form the 64-bit RC4 traffic key. So, WEP 64 on the Linksys & 40-bit is equivalent.
What concerns me more is the loss of bandwidth performance you are experiencing when connecting the AX. When the AX is configured as a wireless client it is acting just like any other wireless devices (computer, laptop, printer, etc.) and not like another router. This should cause little or no bandwidth loss. True the more secure the wireless encryption used WPA2 vs. WEP, the more overhead is required for security, but the differences you are seeing seem excessive.
It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing your Linksys from providing a good clean signal.
I suggest you perform a simple site survey, using utilities like the following to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible:
For Macs:
o MacStumbler
o iStumbler, or
For PCs:
o NetStumbler

Problem with Airport express N (2nd gen)

Problem with Airport express N (2nd gen)
Firmware 7.6.4
ISP - 20 Mbps ethernet cable
I have MacBook Air 13 mid 2013 os x 10.9.5, ipad 4 ios 8.0.2, ipad4 ios 7.1.2 , iphone 5 ios 7.1.1
When i try to use speedtest.net from my Macbook i got good results of download speed and incredible upload http://www.speedtest.net/my-result/3801286946 (connection 300 Mbps) , both ipads got terrible speedtest download result and incredible uploadhttp://www.speedtest.net/my-result/i/981631804 (connection 150 Mbps), iphone 5 got bad download and great uploadhttp://www.speedtest.net/my-result/i/981695357.
All these tests were done near airport express with really good signal and 5ghz. I tried to choose different channels, 802.11 mode, guest ssid, 5ghz ssid ...
I think that something is wrong with my new airport express. Can anyone help me to solve this problem?
ps sorry for my bad english

As a last resort, try a factory default reset on the AirPort Express as follows:
Power off the AirPort Express
Wait a minute
Hold in the reset button first, and keep holding it in for another 8-10 seconds while you simultaneously plug the Express back in to power
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light status
On an iPhone or iPad home screen....
Tap Settings
Tap WiFi
Look for a heading of Setup a New AirPort Base Station. If it appears.....
Tap on AirPort Express just below the heading to start the configuration process on the Express again
If you try several factory default resets, and the AirPort Express does not appear under the heading of Setup a New AirPort Base Station, the Express most likely is defective and will need to be replaced.

HT1515 Just installed Airport Express on Mac 10.6.8 Can't see base station. Hard Reset the Airport. Rebooted machine. How can I tell if this is a Mac problem or Airport Express Problem?

I have a Mac 10.6.8. Just installed Airport Express. I can't see any base stations. I did a hard reset on the Airport Express, turned off all devices, turned them back on. I see plenty of Airport networks in the neighborhood. How can I tell if I have a Mac problem or an Airport Express problem? Airport Express blinks Amber.

Obviously, I'm still using ethernet to be able to reply to this.
Alright, use the same ethernet cable to plug directly into the airport express. This will FORCE the airport utility to now see it regardless of weak signals & interference. You can set it up that way.
BTW, what is the original intent on the express?

When trying to connect airport express keep getting unexpected error please try again. IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL

when trying to connect airport express keep getting unexpected error please try again. IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL

Have you tried using a WEP password for your wireless network instead of a WPA one? That fixed it for me.

Cannot connect airport express to ipad I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express. Does anyone have a solution?

cannot connect airport express to ipad
I keep receiving the message: "an unexpected error occurred" when I try to connect my Ipad to my airport express. Does anyone have a solution?

I could not "see" my Express via my wireless router or via the Airport Utility until I reset it to Factory Settings by unplugging it then holding in the tiny reset button while plugging it back in, waiting for the flashing yellow LED signal before letting go.
Then I set it up to DHCP - "connect to wireless network" and DOWNGRADED the firmware to 7.3.x
I would tell you the exact Firmware but I can no longer "see" the Airport express............ AGAIN or still.....
BUT at least I am listening to music streaming from my MacBook Pro... Hmmm.
I log back into the router (Linksys WRT110) and it no longer shows the Airport Express as a DHCP client AND the Airport utility can no longer "find" any Airport Devices..
So if I don't move, or there are no cosmic events, or maybe my KARMA is effecting the device or my "VIBES" are good, but I'm not sure if will continue to work.. Sure would like to use this little device from hel*.
Since I have had this Airport Express I have spent many hours trying to get it to work.
It works just long enough to fool me and then takes a dump...
Maybe this time?
5 Minute later...
Music was playing. I went into iTunes and switched from Airtunes to Computer speakers. When I tried to switch it back GUESS WHAT?
[An unknown error (-15006) occurred while trying to connect to remote speaker "Airtunes"]
Wonderful Green LED though. Totally useless piece of equipment AFAIK.
Message was edited by: Daniel Shattuck

Connect Airport Express to Motorola Surfboard Modem/Router

I have purchased a Motorola SURFboad eXtreme Wireless-N Cable Modem and Router (model SBG6580). In order to extend the network to all rooms of my condo, I purchased a 2nd generation Airport Express.
I was able to setup the Airport with my Mac using the Airport Utility and I was able to connect to the my network; got a solid green light on the aiport!
When I tried to access the network, using the Mac, in a room farthest from the Cable Modem but next to the Airport Express, I was not able to see my network. As I walked closer to the modem, the network became visible and I was able to connect.
I then tried to turn off all security on the network and got the Airport Express to connect to the network and and got the solid green light again. I tried the same experiment, and got the same result.
So wondering what I need to do to get the Airport Express to connect to the Wireless Modem and extend the network?
Any ideas and suggestions are appreciated!
Thanks in advance!

Unfortunately, Apple tells us that the "extend a wireless network" feature will only work when you have the Express extending another Apple router.
In other words, to "extend" it takes a minimum of two Apple routers.
Your Express has "joined" the network. You can use it for AirTunes or connect a remote printer, but it will not "extend" the signal from the Motorola modem/router and provide more wireless signal coverage.
You would need to connect the Express to the Motorola modem/router using a wired Ethernet connection if you want it to provide more wireless coverage. In this case, the Express would be configured to "create" a wireless network using the same wireless network name, same security settings and same password as the Motorola network. The Express must also be configured to operate in Bridge Mode in this type of setup.

Problems connecting airport express a1264 to bt homehub 3 router in bridge mode

Similar Messages

Maybe you are looking for