Problems sharing internet connection through Airport with a PS3

Does anybody know how to share an internet connection wirelessly with a PS3? I've tried everything including following directions from the tech support people from both Sony and my ISP (Verizon) and nothing works. Last time I've talked to Verizon I've obtained a IP number from them as Sony recommended and that did not work either. Is anybody out there with a PS3 sharing the internet connection through Airport successfully? I'd really appreciate any help. Thanks.!!
Message was edited by: pbranda

Let's double-check your Mac's Internet Sharing settings ...
To setup for Internet Sharing (Wired to Wireless):
Setup the Network
Cable Modem > (Ethernet cable) > \[Ethernet port] Mac > (wireless) > PS3
Enable Software Firewall
System Preferences > Security > Firewall
o Block all incoming connections (enabled)
Enable Internet Sharing
System Preferences > Sharing
o Select "Internet Sharing" from the options in the left column
o Share your connection from: Built-in Ethernet
o To computers using: AirPort (checked) (Note: Uncheck all other entries in the list.)
AirPort Options...
o Network Name: <anything you want>
o Channel: Automatic
o Enable encryption (using WEP) (optional)
o Password: (optional)
o Confirm Password: (optional)
o WEP Key Length: (optional)
o Click OK
o Select "Internet Sharing" again
o Click "Start" to start Internet Sharing
o Click Start

Similar Messages

Problems sharing internet connection over airport

Hi everyone-
I've researched the heck out of the forums and still cant figure out what's happening with my system. I've got a MacBook Pro with OS 10.5.2. In previous OS versions (10.4) when I was successfully sharing my ethernet internet connection, the airport icon in the status bar showed a vertical "up" arrow, indicating that my connection was being shared.
I'm trying to do the same thing in OS 10.5.2 but not succeeding in getting the same notification. I'm finding that when I access the "Sharing" folder under "System Preferences" and select "Share your internet connection from: ethernet" and "To computers using: Airport" that both settings grey out, the "Internet Sharing" button turns green and the status says "On", but no sharing occurs. I've checked using other wireless laptops and a wifi finder, but no signal from my MacBook is ever found.
I've deleted my preferences folder to start fresh, no help. I've tried sharing from different ethernet sources, no help. It just feels like the problem is in the OS somewhere, not with the internet connection.
Any insight or help would be greatly appreciated! Thanks!

seems like i got the same issue as u and i just posted it:
http://discussions.apple.com/thread.jspa?threadID=1425809

Sharing Ethernet Connection Through Airport

Is it possible to share your Ethernet connection through airport so that two computers can connect to a single connection without the need of a wireless router? I know that this is possible on XP, but I am somewhat new with OS X and cannot seem to figure it out. Does anyone have any suggestions?

Open the Sharing preference, click on the Internet tab, select the connection to share from the drop down menu, then check the ports that will share the connection.
You will find additional info by selecting Mac Help from the Finder's Help menu and searching on the appropriate term.
Why reward points?(Quoted from Discussions Terms of Use.)
The reward system helps to increase community participation. When a community member gives you (or another member) a reward for providing helpful advice or a solution to their question, your accumulated points will increase your status level within the community.
Members may reward you with 5 points if they deem that your reply is helpful and 10 points if you post a solution to their issue. Likewise, when you mark a reply as Helpful or Solved in your own created topic, you will be awarding the respondent with the same point values.

Incredibly slow internet (Connected through airport)

Hey there!
I just got myself a new Macbook around 2 months ago and so far I'm very happy with it. I haven't had any problems except for one.
I'm connected to the internet wireless through Airport and since about a week ago loading web pages is going incredibly slow, whether I use Safari or Firefox. I didn't have this problem before and I didn't change any internet settings. Nothing else changed eigher. I'm still connected to the same network and I didn't install any dodgy programs on my network. Downloading or loading videos doesn't seem to be a problem though. When downloading from a fast server like mac or windows (I know I shouldn't but hey, all my friends use msn ;)) I can easily make the 300 kb/sec. Also waching video's on apple.com/trailers isn't a problem. It's only the loading of web pages or sending e-mails. It sometimes takes up to half a minute to even load google.com. I'm not sure but it might have started after a software update. not at all sure though! Can anybody help me please! Thanks!
Regards from the Netherlands,
Jop
Message was edited by: boarderjop

Hi Jop, and Welcome to the discussions!
Two things to try first...
Fix Permissions using the Disk Utility, then reboot. or better yet, get Applejack...
http://www.versiontracker.com/dyn/moreinfo/macosx/19596
After installing, reboot holding down CMD+s, then when the prompt shows, type in...
applejack AUTO
Then let it do all 5 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 5 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
Try putting these in Network>TCP/IP>DNS Servers:
4.2.2.1
4.2.2.2
Might be better ones for you over there, but worth a try.
Message was edited by: BDAqua

Connecting to shared internet connection through Mac osx 10.7 wifi

I can't get my new HP touch pad to connect to my wireless network. I connect my iMac through ethernet but have a wifi network setup from my iMac so my other devices can use my iMacs shared internet connection. The touchpad will not connect, it finds the network, I put in the WEP key and it states "unable to connect, try again". I am at the setup stage on the touch pad and can't get any further!!. I have tried everything I can think of including creating a new wireless network, disabling and changing the sharing password and re-enabling. all my other devices still log on fine and can connect to the internet through the iMacs connection. anyone got any ideas?
Post relates to: HP TouchPad (WiFi)

alopix wrote:
I just remembered why I ignored your first post when reading this topic:
Ad-hoc-sharing can't be the problem, because when I use the exact same method without any WEP encryption, so create an open network, it works perfectly - so it has to be an error in the webOS' handling of WEP or similar...
I'm curious that the Mac offers only ASCII (key length of 5 characters) or 128 bit encryption, but not 64bit (which has a key length of 10 hexadecimal characters and works perfectly with my touchpad). <Wiki definition of WEP.>
This sounds like an old problem we used to have when Palm came out with WiFi-enabled devices. Users would create an ASCII text password in their router, and it would generate a 10 character hexadecimal string that was the true password. Entering the 5-digit ASCII code would fail since it was a seed, and not the "real" code.. Entering the 10-digit key worked every time.
By any chance is this what is occurring on the Mac? Do you see a 10 digit code generated anywhere in the setup routine?
Was the link I provided to you of any help?
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

Problems sharing internet connection - works only one way...

hey all,
i'm having a problem sharing my internet connection between our "new" iBook G4 and "old" iMac G5. (both machines are running 10.4.10.) i've seen several posts here that seem related, but no answers that have worked in my case.
here's the gist:
ideally, i'd like share the internet connection from the iMac (from our cable modem) to the iBook over the airport. so, i've set up the iMac to do this under "sharing" in system preferences. i then set up the iBook to connect to this new wireless network. under "network status", it says the iBook is connected to the iMac's network, but that the iBook doesn't have its own IP address, so it can't connect to the internet.
oddly, when i reverse the process - i.e. plug the modem into the iBook and share the connection over the airport to the iMac - it works fine. the iMac gets its own IP address and can see the internet.
a friend suggests that somehow the iBook is set up to distribute IP addresses as a router, but the iMac isn't. fine. but, i don't know how to make changes to that function.
any thoughts?

well, it's taken all day - many, many attempts. but i've finally found something that worked. the answer was burried in the middle of this guy's blog page:
http://www.tuaw.com/2007/03/26/how-to-using-your-mac-as-a-nat-router/
he says:
"I've turned off DHCP and set the address to: 192.168.0.1 and the subnet to 255.255.255.192 In making these choices I was following a hint that appeared at macOSXhints back in 2002. Once this is done I went back to the Internet tab of Sharing Preference Pane, select en4 and start it.
"Now on my other device (in this case a Xbox 360) I set it up as follows:
"IP address: 192.168.0.2 subnet: 255.255.255.192 (this is the same subnet of the en4 USB interface, above) gateway/router: 192.168.0.1 (this is the address of the en4 interface) DNS: 192.168.2.1
"(here's where the voodoo comes in, I have no idea why this DNS setting works. You would think it should be 192.168.0.1, or even the DNS server of my ISP, but those simply do not work. I suspect that it has something to do with sharing over Airport as well).
"I've also found that this will only work properly if Internet Sharing is active for my Airport interface. If I turn off the Airport interface (en1), the wired interface (en4) also dies. With these settings in place, everything seems to work properly. Keep in mind you may also need to enable certain services (which will vary with your application) in the Services tab of the Sharing Pane:"
i wasn't trying to solve quite the same problem he was, but by manually inputting the IP addresses, etc, that he did, as well as randomly enabling other "sharing" options (FTP access, etc) which seemed unrelated to internet sharing, it finally worked.
can anyone explain what this is about? it all seems pretty cryptic to me. i'm not sure what i even did...
no complaints, but it would be interesting to know.
thanks!

Having problems sharing internet Connection from Macbook to Vonage Adapter

Hello,
I just got my Vonage adaptor and I am trying to share the Internet connection from my Macbook Pro (10.7.3) to the Adaptor to use the Vonage service bc my router is downstairs.
I turned off my Firewall, hooked my Vonage adapter to the Macbook with the ethernet cable and then went to Sys Preferences > Sharing > Selected Internet Sharing > Share Connection from Wifi to computers using Ethernet, and it looks like everything is ok but when i try to use the phone which is connected to to Vonage Adapter, it says "Your Vonage device cannot connect to the internet, check to see if your high speed internet is down".
I went and looked at my Network preferences and it shows Ethernet connected which is the Vonage Adapter and gives the following:
IP Address: 169.254.163.167
Subnet Mask: 255.255.0.0
Is there something Im doing wrong? Ive seen on several forums that its possible to do but having bad luck. Any help is appreciated.

All I know is that I got Ubuntu to share internet and offer IPs through DHCP by using Firestarter. I am very new to Solaris, however, and am looking forward to learning about it. I've just made it my regular desktop environment. Long as you can get Solaris to configure its network interface with DHCP after your Ubuntu is configured, you should be able to share to as many clients as you'd like. Fedora also works well for that, and in my opinion, it's a better Linux than Ubuntu, though Solaris remains a better Linux than Linux, right? Har.

Unabl eto share Internet connection through Airport

I have a new Samsung wave S8500. I'm trying to access the internet connection shared by my mac on the airport, everytime i try to connect to my mac through the Wi-Fi on my phone, it doesn't connect. I put a 40 bit WEP Key length on the sharing options. The airport can connect to my other phone which is a Nokia N97, the Samsung is able to connect directly to my friends Router(wi fi) and I'm able to use the net. I'm unable to pin point where the issue is.

jdmein wrote:
First, before I get into too much detail: Is it even possible to set up a WPA2 network directly from the iMac without a separate router?
Welcome to Apple's discussion groups.
Despite the fact that WPA2 encryption has existed for years, Apple hasn't seen fit to include that option in its "Internet sharing" feature.

Sharing internet connection by airport

My wife and I each have a Mac Book Pro, running Leopard. We have a Verizon card inserted in one of the macs which is then hoooked up to the internet. How do we get the second mac to "share" in this internet connection?
Computer #1 is hooked up to net. I see that I am using the airport to send out signal. I pick up the signal on computer #2 which clearly identifies computer #1 on the airport, and connects to that source. However, Computer #2 still can't click on safari and get on the net. Nothing happens.
Any ideas??
Thanks
Don

open system preferences
click sharing
click internet sharing
choose the share from and share too options
i think its pretty obvious once you get to that screen but if you have troubles post back
i can't remember, is leopard the 10.5 version?
i ask as they changed the way you access internet sharing in 10.5, the layout's a little different
but you should be able to find in system prefs under Sharing in either case
hope this helps!

Share internet connection through iMac with Time Capsule

I have a scenario at work where I need to temporarily set another router as the DHCP server. I have a customer who has a typical office setup. They have an iMac which is plugged into a time capsule (TC). A network printer is also plugged into the same time capsule. I have had to move the WAN modem to where the wifi router is located in another room. The office needs to be able to connect to the new WIFI network while still having the network printer work. If I setup TC to "join another network" and put into bridge mode, I can no longer communicate with network printer. Can I choose "share internet" in OSX system preferences> Sharing on iMac, connect wirelessly through iMac and have TC function as a simple network switch somehow while being able to communicate with printer.
Thanks

jdmein wrote:
First, before I get into too much detail: Is it even possible to set up a WPA2 network directly from the iMac without a separate router?
Welcome to Apple's discussion groups.
Despite the fact that WPA2 encryption has existed for years, Apple hasn't seen fit to include that option in its "Internet sharing" feature.

Sharing Internet Connection through Firewire.

My Network was just re-done and I lost y configuration to Share my iMac's Airport Connection to my iBook via Firewire.
On the iMac I have internet sharing on and have the Firewire port created and at the top of the list. However on the iBook I still can't access the Net.

If your firewall is up on the iMac, open ports 80 and 443 and see if that helps.

IPod Touch Connecting Through Airport with Access Control

Assistance requested.
I want to connect my iPod Touch to my Airport wireless network. I have access controlled to my wireless network so that only devices with an Airport ID specified in the Airport configuration may connect to my wireless network.
Does the iPod Touch have an Airport ID that I can enter into my Airport configuration? I realy do not want to make my wireless network open to anyone.
Thank you,
Doug

Sorry,
Thank you for the contribution. I found my own answer with some searching on the iPod. This was my solution in case somebody else is having a similar problem.
Required address (Airport ID) of the iPod was found as follows:
Settings
General
About
Wi-Fi Address
Added the Wi-Fi Address to my Airport Access Control List.
On the iPod performed the following:
Settings
Wi-Fi
Choose Another Network
Typed in the wireless network name (case-sensitive)
Selected the proper security protocall
Typed in the password to access my Airport Network
Click Join
Problems connecting were resolved and my network remained closed to people not pre-approved to access it.

Sharing internet connection with Windows via Airport

Happy New Year, all!
I have an iMac Intel Core Duo connected to an ADSL modem via ethernet. I'd like to share my internet connection via Airport with a Windows laptop (which is running XP with SP2). I've read that this is possible and I've tried setting it up but the laptop isn't seeing the Airport network at all.
I've created a network with security off, from the Airport drop-down menu in the iMac menu bar, turned Internet Sharing on (Share from: ethernet - to computers using: Airport). I have Windows Sharing and Personal Web Sharing turned on, and my firewall is off. But the Airport network still doesn't show up on the laptop.
Can anyone tell me what I'm doing wrong, or at least point me in the right direction.
Many thanks in advance.

i am having the same problem. i have the mac connected but when i go to windows i can't get the page open that says to connect. when i run the mouse over the icons at the bottom of the page it shows the airport signal being excellent. but i just can't get to a page to enter the "key to connect". it is greyed out and shows that it is limited or not connectivity.
please someone help!
movie lady

Problem with not getting Internet Connect on AirPort Express

Problem with not getting Internet Connect on AirPort Express (version7.6.4). Error says cannot get valid IP address. Have reset Siemens SpeedStream 4100 several time, even with tech support from the big "A" DSL provider. Plug MacBook Pro directly into modem and works fine. Unplugged AirPort, even reset it, still no luck. A bad Express?? or am not looking in the right place to make connection. Was working fine up until Sunday.

Connect the AirPort Express (AX) to the cable modem via Ethernet cable.
In configuring the AX using AirPort Utility:
Under Internet, set the connection to be Ethernet using DHCP.
Under Connection Sharing, set it to distribute a range of IP addresses.
Under AirPort>Wireless, set the Wireless Mode to Create a wireless network, and fill in the remaining settings in the same window. Until you get it working, you might want to set Wireless Security to None.

Airport network and sharing Internet connection

Hello all,
I have hit this problem with sharing an internet connection on an airport network. Maybe its a simple fix, maybe it a "can not be done", answer.
My set up may be a little hard to describe. To explain, completely wireless set up in my network, 1 x imac and 1 x powerbook, all on airport and using an airport express. This includes my new printer. All connected through airport express network, call it network A.
Up till now i had a modem with an ether net cable plugged into the airport express. All was fine.
I am in jakarta, the cable internet providers here are hopeless, slow connection speed.
Last month a new wireless internet service was released. Called 3.5 G. Its lightning fast and reliable. Basically you get a wireless USB modem attach it to your computer and you are always connected to the internet wirelessly. You can travel anywhere with it. The 3.5G is primarily for mobile phones but i use it just for internet. This modem is connected to my powerbook and works great.
Now, the useless cable internet connected to my airport express is still connected for my Imac to use.
My problem is that i would like to share my high speed internet connection from my laptop to my imac. Problem is that when i allow sharing from my laptop, the intenet works fine on both machines but on the powerbook, which is doing the sharing you get an arrow symbol through the airport icon at the top.
The laptop can NOT access the local airport express network A. Hence i cannot use the printer or see the imac. That is my problem, i cannot print from the powerbook unless i stop sharing. When you share an internet connection the sharing computer seems to create another computer to computer network and does not join the existing arirport network.
This is probably a little confusing. Hopefully, someone may have some ideas. My alternative is to buy a new fixed position modem/router for the 3.5G system. Its about $600. Ouch.
Any ideas
thanks for the interest.
joe

Selamat Phil Smith,
Actually do we know each other, cause i know a phil smith.
Actually an ether net cable is OK for the short term. But if i get another computer it may get complex. Spent a lot removing cables too.... Looks like i will have to buy the special modem router... Painful $600.
This share internet thing over airport looks like a great idea till you realise it disables access to the ariport network for the computer doing the sharing.
Cheers and thanks for the idea
joe

Problems sharing internet connection through Airport with a PS3

Similar Messages

Maybe you are looking for