Problems with QuickVPN client
Hello,
I experiance problems with QuickVPN client (version 1.4.1.2). I'm trying to connect to router SA520 with 1.1.65 firmware,
vpn tunell is established, but client says "The remote gateway is not responding. Do you want to wait?"
in case i click no, it drops vpn tunell
QuickVPN client log looks like this:
2010/08/18 12:13:27 [STATUS]OS Version: Windows 7
2010/08/18 12:13:27 [STATUS]Windows Firewall Domain Profile Settings: ON
2010/08/18 12:13:27 [STATUS]Windows Firewall Private Profile Settings: ON
2010/08/18 12:13:27 [STATUS]Windows Firewall Private Profile Settings: ON
2010/08/18 12:13:27 [STATUS]One network interface detected with IP address 192.168.1.100
2010/08/18 12:13:27 [STATUS]Connecting...
2010/08/18 12:13:27 [DEBUG]Input VPN Server Address = vpn.in-volv.lv
2010/08/18 12:13:28 [STATUS]Connecting to remote gateway with IP address: 78.28.223.10
2010/08/18 12:13:28 [WARNING]Server's certificate doesn't exist on your local computer.
2010/08/18 12:13:30 [STATUS]Remote gateway was reached by https ...
2010/08/18 12:13:30 [STATUS]Provisioning...
2010/08/18 12:13:39 [STATUS]Success to connect.
2010/08/18 12:13:39 [STATUS]Tunnel is configured. Ping test is about to start.
2010/08/18 12:13:39 [STATUS]Verifying Network...
2010/08/18 12:13:44 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:47 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:50 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:53 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:56 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:14:08 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2010/08/18 12:14:12 [STATUS]Disconnecting...
2010/08/18 12:14:15 [STATUS]Success to disconnect.
Server logs look like this:
2010-08-18 12:28:49: INFO: Adding IPSec configuration with identifier "arvils"
2010-08-18 12:29:02: INFO: Configuration found for 83.243.93.200[500].
2010-08-18 12:29:02: INFO: Received request for new phase 1 negotiation: 78.28.223.10[500]<=>83.243.93.200[500]
2010-08-18 12:29:02: INFO: Beginning Identity Protection mode.
2010-08-18 12:29:02: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 12:29:02: INFO: Received Vendor ID: RFC 3947
2010-08-18 12:29:02: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: For 83.243.93.200[500], Selected NAT-T version: RFC 3947
2010-08-18 12:29:02: INFO: NAT-D payload matches for 78.28.223.10[500]
2010-08-18 12:29:02: INFO: NAT-D payload does not match for 83.243.93.200[500]
2010-08-18 12:29:02: INFO: NAT detected: PEER
2010-08-18 12:29:02: INFO: Floating ports for NAT-T with peer 83.243.93.200[4500]
2010-08-18 12:29:02: INFO: ISAKMP-SA established for 78.28.223.10[4500]-83.243.93.200[4500] with spi:e2cd855a75fc0887:6dc3b2e025152444
2010-08-18 12:29:02: INFO: Sending Informational Exchange: notify payload[INITIAL-CONTACT]
2010-08-18 12:29:02: INFO: Responding to new phase 2 negotiation: 78.28.223.10[0]<=>83.243.93.200[0]
2010-08-18 12:29:02: INFO: Using IPsec SA configuration: 192.168.75.0/24<->192.168.1.100/32
2010-08-18 12:29:02: INFO: Adjusting peer's encmode 3(3)->Tunnel(1)
2010-08-18 12:29:02: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 83.243.93.200->78.28.223.10 with spi=47693803(0x2d7bfeb)
2010-08-18 12:29:02: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 78.28.223.10->83.243.93.200 with spi=1079189482(0x40531fea)
2010-08-18 12:35:57: INFO: an undead schedule has been deleted: 'pk_recvupdate'.
2010-08-18 12:35:57: INFO: Purged IPsec-SA with proto_id=ESP and spi=1079189482(0x40531fea).
2010-08-18 12:40:46: INFO: Configuration found for 83.243.93.200[500].
2010-08-18 12:40:46: INFO: Received request for new phase 1 negotiation: 78.28.223.10[500]<=>83.243.93.200[500]
2010-08-18 12:40:46: INFO: Beginning Identity Protection mode.
2010-08-18 12:40:46: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 12:40:46: INFO: Received Vendor ID: RFC 3947
2010-08-18 12:40:46: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 12:40:46: INFO: Received unknown Vendor ID
2010-08-18 12:40:46: INFO: Received unknown Vendor ID
2010-08-18 12:40:46: INFO: Received unknown Vendor ID
2010-08-18 12:40:46: INFO: For 83.243.93.200[500], Selected NAT-T version: RFC 3947
2010-08-18 12:40:46: INFO: NAT-D payload matches for 78.28.223.10[500]
2010-08-18 12:40:46: INFO: NAT-D payload does not match for 83.243.93.200[500]
2010-08-18 12:40:46: INFO: NAT detected: PEER
2010-08-18 12:40:46: INFO: Floating ports for NAT-T with peer 83.243.93.200[4500]
2010-08-18 12:40:46: INFO: ISAKMP-SA established for 78.28.223.10[4500]-83.243.93.200[4500] with spi:28447d39874689f9:a2b7da19d8d86413
2010-08-18 12:40:46: INFO: Responding to new phase 2 negotiation: 78.28.223.10[0]<=>83.243.93.200[0]
2010-08-18 12:40:46: INFO: Using IPsec SA configuration: 192.168.75.0/24<->192.168.1.100/32
2010-08-18 12:40:46: INFO: Adjusting peer's encmode 3(3)->Tunnel(1)
2010-08-18 12:40:47: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 83.243.93.200->78.28.223.10 with spi=259246202(0xf73c87a)
2010-08-18 12:40:47: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 78.28.223.10->83.243.93.200 with spi=3642234214(0xd9181566)
2010-08-18 12:43:27: INFO: IPsec-SA expired: ESP/Tunnel 83.243.93.200->78.28.223.10 with spi=33356156(0x1fcf97c)
2010-08-18 12:45:47: INFO: an undead schedule has been deleted: 'pk_recvupdate'.
2010-08-18 12:45:47: INFO: Purged IPsec-SA with proto_id=ESP and spi=3642234214(0xd9181566).
The most interesting thing is that sometimes this message appears, sometimes not (with the same configuration).
Please help!
Hi,
I have some problem. I am using Windows 7 Entreprice x64. I use SA520 Firmware 1.1.65 and QuickVPN 1.4.1.2 port 60443.
"The remote gateway is not responding. Do you want to wait"
2010-08-18 17:25:51: INFO: Adding IPSec configuration with identifier "username"
2010-08-18 17:25:51: INFO: Adding IKE configuration with identifer "username"
2010-08-18 17:26:04: INFO: Configuration found for xxx.xxx.xxx.xxx[235].
2010-08-18 17:26:04: INFO: Received request for new phase 1 negotiation: 172.22.5.10[500]<=>xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:04: INFO: Beginning Identity Protection mode.
2010-08-18 17:26:04: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 17:26:04: INFO: Received Vendor ID: RFC 3947
2010-08-18 17:26:04: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: For xxx.xxx.xxx.xxx[235], Selected NAT-T version: RFC 3947
2010-08-18 17:26:04: INFO: NAT-D payload does not match for 172.22.5.10[500]
2010-08-18 17:26:04: INFO: NAT-D payload does not match for xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:04: INFO: NAT detected: ME PEER
2010-08-18 17:26:04: INFO: Floating ports for NAT-T with peer xxx.xxx.xxx.xxx[48540]
2010-08-18 17:26:04: INFO: ISAKMP-SA established for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:ed4f291c71c1b688:7e6a8a0968f878fb
2010-08-18 17:26:04: INFO: Sending Informational Exchange: notify payload[INITIAL-CONTACT]
2010-08-18 17:26:04: INFO: Responding to new phase 2 negotiation: 172.22.5.10[0]<=> xxx.xxx.xxx.xxx[0]
2010-08-18 17:26:04: INFO: Using IPsec SA configuration: 192.168.75.0/24<->192.168.170.224/32
2010-08-18 17:26:04: INFO: Adjusting peer's encmode 3(3)->Tunnel(1)
2010-08-18 17:26:05: INFO: IPsec-SA established[UDP encap 48540->4500]: ESP/Tunnel xxx.xxx.xxx.xxx->172.22.5.10 with spi=239099274(0xe405d8a)
2010-08-18 17:26:05: INFO: IPsec-SA established[UDP encap 4500->48540]: ESP/Tunnel 172.22.5.10-> xxx.xxx.xxx.xxx with spi=3886848189(0xe7ac98bd)
2010-08-18 17:26:07: INFO: Configuration found for xxx.xxx.xxx.xxx[235].
2010-08-18 17:26:07: INFO: Received request for new phase 1 negotiation: 172.22.5.10[500]<=> xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:07: INFO: Beginning Identity Protection mode.
2010-08-18 17:26:07: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 17:26:07: INFO: Received Vendor ID: RFC 3947
2010-08-18 17:26:07: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 17:26:07: INFO: Received unknown Vendor ID
2010-08-18 17:26:07: INFO: Received unknown Vendor ID
2010-08-18 17:26:07: INFO: Received unknown Vendor ID
2010-08-18 17:26:07: INFO: For xxx.xxx.xxx.xxx[235], Selected NAT-T version: RFC 3947
2010-08-18 17:26:07: INFO: NAT-D payload does not match for 172.22.5.10[500]
2010-08-18 17:26:07: INFO: NAT-D payload does not match for xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:07: INFO: NAT detected: ME PEER
2010-08-18 17:26:07: INFO: Floating ports for NAT-T with peer xxx.xxx.xxx.xxx[48540]
2010-08-18 17:26:07: INFO: ISAKMP-SA established for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:699f34b434d4318c:df4adca414787d36
2010-08-18 17:27:14: INFO: Purged ISAKMP-SA with proto_id=ISAKMP and spi=699f34b434d4318c:df4adca414787d36.
2010-08-18 17:27:14: INFO: Configuration found for xxx.xxx.xxx.xxx[235].
2010-08-18 17:27:14: INFO: Received request for new phase 1 negotiation: 172.22.5.10[500]<=> xxx.xxx.xxx.xxx[235]
2010-08-18 17:27:14: INFO: Beginning Identity Protection mode.
2010-08-18 17:27:14: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 17:27:14: INFO: Received Vendor ID: RFC 3947
2010-08-18 17:27:14: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 17:27:14: INFO: Received unknown Vendor ID
2010-08-18 17:27:14: INFO: Received unknown Vendor ID
2010-08-18 17:27:14: INFO: Received unknown Vendor ID
2010-08-18 17:27:14: INFO: For xxx.xxx.xxx.xxx[235], Selected NAT-T version: RFC 3947
2010-08-18 17:27:14: INFO: NAT-D payload does not match for 172.22.5.10[500]
2010-08-18 17:27:14: INFO: NAT-D payload does not match for xxx.xxx.xxx.xxx[235]
2010-08-18 17:27:14: INFO: NAT detected: ME PEER
2010-08-18 17:27:15: INFO: ISAKMP-SA deleted for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:699f34b434d4318c:df4adca414787d36
2010-08-18 17:27:15: INFO: Floating ports for NAT-T with peer xxx.xxx.xxx.xxx[48540]
2010-08-18 17:27:15: INFO: ISAKMP-SA established for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:3fe5eb0bddbf2b9a:f5c11d7f813ca74a
2010-08-18 17:27:15: INFO: Sending Informational Exchange: notify payload[INITIAL-CONTACT]
2010-08-18 17:28:20: INFO: Purged ISAKMP-SA with proto_id=ISAKMP and spi=3fe5eb0bddbf2b9a:f5c11d7f813ca74a.
2010-08-18 17:28:21: INFO: ISAKMP-SA deleted for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:3fe5eb0bddbf2b9a:f5c11d7f813ca74a
With windows XP Pro i dont have this problem.
Is there a detailed configuration guide?
10x
Similar Messages
-
Problem with Variable Client Support
Hello,
I work with Labview 8.5 and Crio 9014.
I have a problem with Variable Client Support. When I try to compile my project I have the following error:
"The Network Variable Engine and Variable Client Support must be installed on the RT target for this application to function properly..."
I have read that we have to install the Variable Client Support in Measurement and Automation by right-clicking on the software and then choosing add/remove software but I can't install the appropriate shared variable components because I can't see neither Network Variable Engine and Variable Client Support. So what can I do?
Can somebody help me?
ThanksI have exactly the same problem. I wanted go through the "Getting Started with the LabVIEW RT module" and when I use wizard for generating new project I get same notification in my VI...
The Network Variable Engine and Variable Client Support must be installed on the RT target
for this application to function properly. If the Network Variable Engine is not supported on
the target (e.g. FP-2000 with <32MB of RAM), open the project and move the variable library
to My Computer in the project. Doing this will deploy the variables to localhost but
will still require that Variable Client Support be installed on the RT target.
Could someone help please ?
Attachments:
ni.png 95 KB -
I encountered a problem with some client machines that use Firefox version 24ESR and IE8.
Ajax requests of aspx pages from Firefox are getting the following error from the iis server (iis version 7.5):
Bad Request - Request Too Long
HTTP Error 400. The size of the request headers is too long.
From analyzing the request that was sent to the server, I saw that the request consist of only the viewstate of the aspx page.
I tried to disable the viewstate for one page and the server got the request correctly.
I do not encounter any issues on these laptops with postback requests from Firefox or when running the same application with IE8.Sometimes that means that the page address sent is loo long.
Check the link address you are using.
I can't help you further and will send for more help. -
DHCP problem with wireless clients
I've just set up this eqipment
Router/Firewall ASA 5505
Cisco WLC 2125 - Wlan controller
Switch Catalyst 2960
16 Ap's AIR-LAP1131AG-E-K9
Everything was working fine, but after a while there was a problem, spesially with cell phones with wlan and with some laptops. It seems a part of the users that has been connected, then loggout out and try to log in again. It seems that they then dont get dhcp. Can this be a problem with dhcp on the asa 5505? Or does anyone know of any settings that create problems of this type.
TrondOne layman's question:
For DHCP to work, you already permit 0.0.0.0 to ask 255.255.255.255 for its IP adress (i.e port 67 in one end, and 68 in the other).
When a client re-attaches ("logs in again") it will try to use its old adress (the one assigned by dhcp) and ask 255.255.255.255 to renew its adress.
Does your ACLs permit the IP range assigned via DHCP to access 255.255.255.255?
//Svein -
Problem with VPN Client passthrough on ASA 5505
I am having a problem with passing through a VPN client connection on an ASA 5505. The ASA is running version 8 and terminates an anyconnect VPN. The ASA is using PAT. When the inside user connects with the VPN client, it connects but no traffic passes through the tunnel. I see the error
305006 regular translation creation failed for protocol 50 src INSIDE:y.y.y.y dst OUTSIDE:x.x.x.x
UDP 500,4500 and ESP are allowed into the ASA. Ipsec inspection has also been setup on a global policy, but the user still cannot pass traffice to the remote VPN he is connected through.
At the Main Office we have an ASA 5510 that terminates a site to site VPN, allows remote connections with PAT and allows passthrough no problems. Any ideas?I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP? -
Problem with Macintosh client on 10.5.6
I am having a problem with applying color lables and I was wondering if anybody else was. My server was upgraded to 10.5.6 and ever since then, when on a Macintosh client, applying a color label will not work as expected. I can label a file a color and it shows, but when I click off the file, it changes back to the previous color {or no label if it previously didn't have a label}. If I click on the file again, then the label seems to stick, but even this isn't consistent. It seems that the label does look correct when I look on the server itself. We use the labels quite a lot in my workgroup as a simple way to organize works in progress. Can anybody replicate this on their system? Also, this happens on both clients running 10.5.5 and 10.5.6 (and even 10.5.3 I think)
thanks,
sean rossYes, this appears to be a bug introduced with whatever modifications Apple made to AFP in 10.5.6. See this thread for more info, but no solution yet: http://discussions.apple.com/thread.jspa?messageID=8776293
Message was edited by: JJakucyk -
New WSUS on Server 2012 - problem with win8 clients
Hi,
Two weeks ago we created a new Server 2012 and installed the WSUS role from scratch on it. Its version number is: 6.2.9200.16384. It replaced a Server 2008 WSUS server. After some time all the win7 clients updated and reported as
they did on the old and replaced server.
However all our win8 clients refuse to update against this server. They show correctly up in WSUS server console each with 107 needed updates day after day. We have rebooted them and done numerous wuauclt /resetauthorization /detectnow and wuauclt
/detectnow /reportnow, but to no avail.
I paste in some lines from a win8 client winupdate log at the end of this message if someone can figure out what I have to do to get these clients update as they did against the old wsus server. Thanks for help on this issue.
regards Tor
2014-02-03 08:33:38:008 920 153c Agent *************
2014-02-03 08:33:38:008 920 153c Agent ** START ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:38:008 920 153c Agent *********
2014-02-03 08:33:38:008 920 153c Agent * Online = Yes; Ignore download priority = No
2014-02-03 08:33:38:008 920 153c Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation'
or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-02-03 08:33:38:008 920 153c Agent * ServiceID = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} Third party service
2014-02-03 08:33:38:008 920 153c Agent * Search Scope = {Machine & All Users}
2014-02-03 08:33:38:008 920 153c Agent * Caller SID for Applicability: S-1-5-18
2014-02-03 08:33:38:008 920 153c Misc Validating signature for C:\Windows\SoftwareDistribution\WuRedir\9482F4B4-E343-43B6-B170-9A65BC822C77\wuredir.cab:
2014-02-03 08:33:38:008 920 1990 AU >>## RESUMED ## AU: Search for updates [CallId = {ABC7E77F-635F-4192-9B92-CBF9B1CB8AB0} ServiceId = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7}]
2014-02-03 08:33:38:008 920 1990 AU # 0 updates detected
2014-02-03 08:33:38:008 920 1990 AU #########
2014-02-03 08:33:38:008 920 1990 AU ## END ## AU: Search for updates [CallId = {ABC7E77F-635F-4192-9B92-CBF9B1CB8AB0} ServiceId = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7}]
2014-02-03 08:33:38:008 920 1990 AU #############
2014-02-03 08:33:38:023 920 153c Misc Microsoft signed: Yes
2014-02-03 08:33:38:023 920 153c Misc Infrastructure signed: Yes
2014-02-03 08:33:38:023 920 153c EP Got 9482F4B4-E343-43B6-B170-9A65BC822C77 redir SecondaryServiceAuth URL: "http://fe1.ws.microsoft.com/w8/2/redir/storeauth.cab"
2014-02-03 08:33:38:023 920 153c Misc Validating signature for C:\Windows\SoftwareDistribution\WuRedir\117CAB2D-82B1-4B5A-A08C-4D62DBEE7782\wuredir.cab:
2014-02-03 08:33:38:039 920 153c Misc Microsoft signed: Yes
2014-02-03 08:33:38:039 920 153c Misc Infrastructure signed: Yes
2014-02-03 08:33:38:039 920 153c EP Got 117CAB2D-82B1-4B5A-A08C-4D62DBEE7782 redir Client/Server URL: "https://fe2.ws.microsoft.com/v6/ClientWebService/client.asmx"
2014-02-03 08:33:38:055 920 153c PT +++++++++++ PT: Synchronizing server updates +++++++++++
2014-02-03 08:33:38:055 920 153c PT + ServiceId = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782}, Server URL = https://fe2.ws.microsoft.com/v6/ClientWebService/client.asmx
2014-02-03 08:33:38:055 920 153c Agent Reading cached app categories using lifetime 604800 seconds
2014-02-03 08:33:38:055 920 153c Agent Read 0 cached app categories
2014-02-03 08:33:39:211 920 153c Agent * Added update {E7FF661C-6A03-4387-A1EE-1D723B52EF60}.3 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {E8B477DF-479E-4BCA-B8F8-2D987A509009}.2 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {BB85CCA0-88DC-4DA7-8E81-B7F7E5E73B81}.100 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {18DEF1D9-4513-467E-9D7E-E1772855BB9E}.100 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {971D9BE4-5145-4DB5-962C-CEE2EE3A2842}.3 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {CCB380C9-29F5-4305-96DD-86DE2D00438B}.2 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {455BDD67-9ED0-4DE7-94F1-3480EA942414}.12 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {ADFBFCE0-FFD4-4826-B9CF-50AE8182E3C5}.2 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {BFA8C8B8-EEF7-4A82-A36C-8F760F792430}.3 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {3F05DE38-92BC-44B6-B06B-5217E5CF12CA}.1 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {A9A0E183-0667-46D6-84E4-17CEBCEE5A22}.1 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {36BEF0D5-80ED-4942-8457-6F9C88546E06}.1 to search result
2014-02-03 08:33:39:211 920 153c Agent * Added update {A292CD86-AB4E-4388-8C7B-CFB392EDE6AC}.1 to search result
2014-02-03 08:33:39:211 920 153c Agent * Found 13 updates and 31 categories in search; evaluated appl. rules of 69 out of 94 deployed entities
2014-02-03 08:33:39:211 920 153c Agent *********
2014-02-03 08:33:39:211 920 153c Agent ** END ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:211 920 153c Agent *************
2014-02-03 08:33:39:211 920 1a64 Report REPORT EVENT: {0786C161-F6DC-4842-85D6-9506124654AD} 2014-02-03 08:33:38:008+0100 1
147 [AGENT_DETECTION_FINISHED] 101 {00000000-0000-0000-0000-000000000000} 0 0 Windows Update Command Line Success Software Synchronization
Windows Update Client successfully detected 0 updates.
2014-02-03 08:33:39:211 920 1a64 Report REPORT EVENT: {1E5D9728-220F-44A3-8BCC-ADE69687531D} 2014-02-03 08:33:38:008+0100 1
156 [AGENT_STATUS_30] 101 {00000000-0000-0000-0000-000000000000} 0 0 Windows Update Command Line Success Pre-Deployment Check
Reporting client status.
2014-02-03 08:33:39:211 920 1a64 Report REPORT EVENT: {57BAB7D0-685B-4D73-BDF7-82AFCE8675B0} 2014-02-03 08:33:39:211+0100 1
147 [AGENT_DETECTION_FINISHED] 101 {00000000-0000-0000-0000-000000000000} 0 0 Windows Update Command Line Success Software Synchronization
Windows Update Client successfully detected 13 updates.
2014-02-03 08:33:39:211 920 1a64 Report CWERReporter finishing event handling. (00000000)
2014-02-03 08:33:39:227 920 153c Agent *************
2014-02-03 08:33:39:227 920 153c Agent ** START ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:227 920 153c Agent *********
2014-02-03 08:33:39:227 920 153c Agent * Online = No; Ignore download priority = No
2014-02-03 08:33:39:227 920 153c Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation'
or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-02-03 08:33:39:227 920 153c Agent * ServiceID = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} Third party service
2014-02-03 08:33:39:227 920 153c Agent * Search Scope = {Current User}
2014-02-03 08:33:39:227 920 153c Agent * Caller SID for Applicability: S-1-5-21-4260610346-2664610402-3334891387-1155
2014-02-03 08:33:39:258 920 153c Agent * Added update {E8B477DF-479E-4BCA-B8F8-2D987A509009}.2 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {BB85CCA0-88DC-4DA7-8E81-B7F7E5E73B81}.100 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {18DEF1D9-4513-467E-9D7E-E1772855BB9E}.100 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {971D9BE4-5145-4DB5-962C-CEE2EE3A2842}.3 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {CCB380C9-29F5-4305-96DD-86DE2D00438B}.2 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {455BDD67-9ED0-4DE7-94F1-3480EA942414}.12 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {ADFBFCE0-FFD4-4826-B9CF-50AE8182E3C5}.2 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {3F05DE38-92BC-44B6-B06B-5217E5CF12CA}.1 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {A9A0E183-0667-46D6-84E4-17CEBCEE5A22}.1 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {36BEF0D5-80ED-4942-8457-6F9C88546E06}.1 to search result
2014-02-03 08:33:39:258 920 153c Agent * Added update {A292CD86-AB4E-4388-8C7B-CFB392EDE6AC}.1 to search result
2014-02-03 08:33:39:258 920 153c Agent * Found 11 updates and 29 categories in search; evaluated appl. rules of 58 out of 94 deployed entities
2014-02-03 08:33:39:258 920 153c Agent *********
2014-02-03 08:33:39:258 920 153c Agent ** END ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:258 920 153c Agent *************
2014-02-03 08:33:39:258 920 153c Agent *************
2014-02-03 08:33:39:258 920 153c Agent ** START ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:258 920 153c Agent *********
2014-02-03 08:33:39:258 920 153c Agent * Online = No; Ignore download priority = No
2014-02-03 08:33:39:258 920 153c Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation'
or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-02-03 08:33:39:258 920 153c Agent * ServiceID = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} Third party service
2014-02-03 08:33:39:258 920 153c Agent * Search Scope = {Current User}
2014-02-03 08:33:39:258 920 153c Agent * Caller SID for Applicability: S-1-5-21-2212025170-3189117132-1219651784-500
2014-02-03 08:33:39:305 920 153c Agent * Added update {E8B477DF-479E-4BCA-B8F8-2D987A509009}.2 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {BB85CCA0-88DC-4DA7-8E81-B7F7E5E73B81}.100 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {18DEF1D9-4513-467E-9D7E-E1772855BB9E}.100 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {971D9BE4-5145-4DB5-962C-CEE2EE3A2842}.3 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {CCB380C9-29F5-4305-96DD-86DE2D00438B}.2 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {455BDD67-9ED0-4DE7-94F1-3480EA942414}.12 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {ADFBFCE0-FFD4-4826-B9CF-50AE8182E3C5}.2 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {BFA8C8B8-EEF7-4A82-A36C-8F760F792430}.3 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {3F05DE38-92BC-44B6-B06B-5217E5CF12CA}.1 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {36BEF0D5-80ED-4942-8457-6F9C88546E06}.1 to search result
2014-02-03 08:33:39:305 920 153c Agent * Added update {A292CD86-AB4E-4388-8C7B-CFB392EDE6AC}.1 to search result
2014-02-03 08:33:39:305 920 153c Agent * Found 11 updates and 30 categories in search; evaluated appl. rules of 60 out of 94 deployed entities
2014-02-03 08:33:39:305 920 153c Agent *********
2014-02-03 08:33:39:305 920 153c Agent ** END ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:305 920 153c Agent *************
2014-02-03 08:33:39:305 920 153c Agent *************
2014-02-03 08:33:39:305 920 153c Agent ** START ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:305 920 153c Agent *********
2014-02-03 08:33:39:305 920 153c Agent * Online = No; Ignore download priority = No
2014-02-03 08:33:39:305 920 153c Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation'
or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-02-03 08:33:39:305 920 153c Agent * ServiceID = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} Third party service
2014-02-03 08:33:39:305 920 153c Agent * Search Scope = {Current User}
2014-02-03 08:33:39:305 920 153c Agent * Caller SID for Applicability: S-1-5-21-4260610346-2664610402-3334891387-1323
2014-02-03 08:33:39:352 920 153c Agent * Added update {E8B477DF-479E-4BCA-B8F8-2D987A509009}.2 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {BB85CCA0-88DC-4DA7-8E81-B7F7E5E73B81}.100 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {18DEF1D9-4513-467E-9D7E-E1772855BB9E}.100 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {971D9BE4-5145-4DB5-962C-CEE2EE3A2842}.3 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {CCB380C9-29F5-4305-96DD-86DE2D00438B}.2 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {455BDD67-9ED0-4DE7-94F1-3480EA942414}.12 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {ADFBFCE0-FFD4-4826-B9CF-50AE8182E3C5}.2 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {BFA8C8B8-EEF7-4A82-A36C-8F760F792430}.3 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {3F05DE38-92BC-44B6-B06B-5217E5CF12CA}.1 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {36BEF0D5-80ED-4942-8457-6F9C88546E06}.1 to search result
2014-02-03 08:33:39:352 920 153c Agent * Added update {A292CD86-AB4E-4388-8C7B-CFB392EDE6AC}.1 to search result
2014-02-03 08:33:39:352 920 153c Agent * Found 11 updates and 30 categories in search; evaluated appl. rules of 60 out of 94 deployed entities
2014-02-03 08:33:39:352 920 153c Agent *********
2014-02-03 08:33:39:352 920 153c Agent ** END ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:352 920 153c Agent *************
2014-02-03 08:33:39:352 920 153c Agent *************
2014-02-03 08:33:39:352 920 153c Agent ** START ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:352 920 153c Agent *********
2014-02-03 08:33:39:352 920 153c Agent * Online = No; Ignore download priority = No
2014-02-03 08:33:39:352 920 153c Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation'
or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-02-03 08:33:39:352 920 153c Agent * ServiceID = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} Third party service
2014-02-03 08:33:39:352 920 153c Agent * Search Scope = {Current User}
2014-02-03 08:33:39:352 920 153c Agent * Caller SID for Applicability: S-1-5-21-4260610346-2664610402-3334891387-1282
2014-02-03 08:33:39:383 920 153c Agent * Added update {E8B477DF-479E-4BCA-B8F8-2D987A509009}.2 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {BB85CCA0-88DC-4DA7-8E81-B7F7E5E73B81}.100 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {18DEF1D9-4513-467E-9D7E-E1772855BB9E}.100 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {971D9BE4-5145-4DB5-962C-CEE2EE3A2842}.3 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {CCB380C9-29F5-4305-96DD-86DE2D00438B}.2 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {455BDD67-9ED0-4DE7-94F1-3480EA942414}.12 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {ADFBFCE0-FFD4-4826-B9CF-50AE8182E3C5}.2 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {BFA8C8B8-EEF7-4A82-A36C-8F760F792430}.3 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {3F05DE38-92BC-44B6-B06B-5217E5CF12CA}.1 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {36BEF0D5-80ED-4942-8457-6F9C88546E06}.1 to search result
2014-02-03 08:33:39:383 920 153c Agent * Added update {A292CD86-AB4E-4388-8C7B-CFB392EDE6AC}.1 to search result
2014-02-03 08:33:39:383 920 153c Agent * Found 11 updates and 30 categories in search; evaluated appl. rules of 60 out of 94 deployed entities
2014-02-03 08:33:39:383 920 153c Agent *********
2014-02-03 08:33:39:383 920 153c Agent ** END ** Agent: Finding updates [CallerId = Windows Update Command Line]
2014-02-03 08:33:39:383 920 153c Agent *************
2014-02-03 08:33:39:383 920 1990 AU >>## RESUMED ## AU: Search for updates [CallId = {66AF0139-896D-4607-8660-B66D2B58EA26} ServiceId = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782}]
2014-02-03 08:33:39:383 920 1990 AU # 12 updates detected
2014-02-03 08:33:39:383 920 1990 AU #########
2014-02-03 08:33:39:383 920 1990 AU ## END ## AU: Search for updates [CallId = {66AF0139-896D-4607-8660-B66D2B58EA26} ServiceId = {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782}]
2014-02-03 08:33:39:383 920 1990 AU #############
2014-02-03 08:33:39:383 920 1990 AU All AU searches complete.
2014-02-03 08:33:39:383 920 1990 AU AU setting next detection timeout to 2014-02-03 10:18:51
2014-02-03 08:33:44:211 920 1a64 Report CWERReporter finishing event handling. (00000000)
2014-02-03 08:41:39:472 920 1a64 EP Got WSUS Client/Server URL: "http://elias:8530/ClientWebService/client.asmx"
2014-02-03 08:41:39:472 920 1a64 PT WARNING: Cached cookie has expired or new PID is available
2014-02-03 08:41:39:472 920 1a64 EP Got WSUS SimpleTargeting URL: "http://elias:8530"
2014-02-03 08:41:39:472 920 1a64 PT Initializing simple targeting cookie, clientId = c5e26849-287b-4b96-ba5d-1489d6fad2f2, target group = , DNS name = dt-ikt-tor.framnes.lan
2014-02-03 08:41:39:472 920 1a64 PT Server URL = http://elias:8530/SimpleAuthWebService/SimpleAuth.asmx
2014-02-03 08:41:39:519 920 1a64 EP Got WSUS Reporting URL: "http://elias:8530/ReportingWebService/ReportingWebService.asmx"
2014-02-03 08:41:39:519 920 1a64 Report Uploading 2 events using cached cookie, reporting URL = http://elias:8530/ReportingWebService/ReportingWebService.asmx
2014-02-03 08:41:39:566 920 1a64 Report Reporter successfully uploaded 2 events.
2014-02-03 08:42:13:212 920 178c Report WARNING: CSerializationHelper:: InitSerialize failed : 0x80070002
2014-02-03 08:43:40:450 920 178c AU ########### AU: Uninitializing Automatic Updates ###########
2014-02-03 08:43:40:450 920 178c WuTask Uninit WU Task Manager
2014-02-03 08:43:40:513 920 178c Service *********
2014-02-03 08:43:40:513 920 178c Service ** END ** Service: Service exit [Exit code = 0x240001]
2014-02-03 08:43:40:513 920 178c Service *************Today I opened Control Panel / Windows Updates and first did a check for new updates (from the WSUS server). Nothing was found and it reported Windows is Updated. Then I clicked the link Check for updates from Microsoft via internet, and
it found around 24 updates.
This is confirmation of the point that I made in the previous post. The updates are *NEEDED* by this system, but the updates were not *AVAILABLE* from the assigned WSUS Server. You were able to get them from Windows Update, but that does not fix your continuing
issue with the WSUS Server.
but it still reported the original 108 Needed updates.
Exactly. As previously noted, the client is functioning perfectly. The problem is NOT with the client; the problem is with the WSUS Server. The updates that this client needed were not AVAILABLE to be downloaded from the WSUS server.
Why this is the case requires further investigation on your part, but is either because the updates are not properly approved, or the update FILES are not yet downloaded from Microsoft to the WSUS server.
It appears that the wsus server doesn't get any information back from the client despite that it displays new Last contact and Last Status report timestamps.
This conclusion is incorrect. The WSUS Server got every bit of information available from the client -- you've confirmed this by the number of updates reported as "Needed" by the Windows Update Agent to the WSUS Server.
I assumed that the log would display if the updates were downloaded or not.
It will log when the updates are actually downloaded. If there's no log entries for updates being downloaded, then they're not being downloaded. If the logfile says "Found 0 updates", then that means exactly what it says: It couldn't find any approved/available
updates to download.
In your case it "Found 11 updates", but now it will be impossible to diagnose that fault, because you went and got them from Windows Update.
All Win8 versions are checked in the WSUS server's Product list so the updates should at least have been downloaded to the server.
This is why understanding the infrastructure is so critical. Your conclusion is invalid based on the premise given, and you may be using improper terminology which only confuses the rest of us as well.
First, selecting updates for synchronization only gets the update metadata (i.e. the detection logic) downloaded to the WSUS database.
The Second Step in this process is to Approve those updates for one or more WSUS Target Groups that contain the appropriate client systems. Following the approval of an update, the WSUS Server downloads the INSTALLATION FILE for that update.
Once the WUAgent sees an approved update and the installation file is available, then the WUAgent will download the file and schedule the update for installation.
Most of the post I read about my problem is about upgrading a 2008 WSUS server to support Win8 / Server 12 clients. When I try to run this update on my Server 12 WSUS it refuses to run (probably because it is for Server 2008).
Yeah.. totally different issue in those posts than what you're describing here.
What should I do to try to track down the problem?
Well.... now that it's 11 days since the logfile was posted, and you've already updated that system, we'll first need to find another system exhibiting the same issue.
Then I'll need to ask a number of questions to properly understand the environment, as well as what you have or have not done.
Then, from there, we can attempt to figure out why your Windows 8 client apparently sees some updates as approved/available but is still not downloading them. We do not yet have sufficient information to even speculate on a possible cause -- there are several.
Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
SolarWinds Head Geek
Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
http://www.solarwinds.com/gotmicrosoft
The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds. -
Problem with VPN Client and network access
We are running VPN client 4.0.1 on our laptops, and there are a number of users who are getting documents they are using on the internal network (off VPN) corrupted. The initial cause seemed to be the stateful firewall, but I have that turned off, and we are still getting it.
It only seems to be on the machines with VPN client installed, and it is only happening when the user is working on a file direct from the network drive. They are not connecting via the VPN client when the problem occurs.
any suggestions?
William.Did you get any joy with this ? We seem to be having the same issue.
Thanks -
ISE 1.2 web authentication problem with wired clients
Hello,
i am having problems with centralized web authentication using a Catalyst 3650X with IOS 15.0.2 SE01 and ISE 1.2.
Redirecting the client works fine, but as soon the client opens a web browser and ISE websites open to authenticate the client, the switch port resets, the authentication process restarts and the session ID changes. After the client enters the credentials a session expired messages appears on the client and i get an 86017 Session Missing message in ISE.
here the output form the debug aaa coa log.
Any ideas
thanks in advanced
Alex
! CLIENT CONNECT TO SWITCHPORT
ISE-TEST-SWITCH#show authentication sessions interface gi0/3
Interface: GigabitEthernet0/3
MAC Address: 001f.297b.bd82
IP Address: 10.2.12.45
User-Name: 00-1F-29-7B-BD-82
Status: Authz Success
Domain: DATA
Security Policy: Should Secure
Security Status: Unsecure
Oper host mode: multi-auth
Oper control dir: both
Authorized By: Authentication Server
Vlan Policy: N/A
ACS ACL: xACSACLx-IP-PERMIT_ALL_TRAFFIC-537cb1d6
URL Redirect ACL: ACL-WEBAUTH-REDIRECT
URL Redirect: https://nos-ch-wbn-ise1.nosergroup.lan:8443/guestportal/gateway?sessionId=AC1484640000026B28C02CDC&action=cwa
Session timeout: N/A
Idle timeout: N/A
Common Session ID: AC1484640000026B28C02CDC
Acct Session ID: 0x0000029C
Handle: 0x8C00026C
Runnable methods list:
Method State
dot1x Failed over
mab Authc Success
! CLIENT OPENS INTERNETEXPLORER -> REDIRECTS TO ISE
! SWITCHPORT GOES IN ADMINISTRATIVE DOWN STARTS AUTHENTICATION AGAIN
ISE-TEST-SWITCH#
191526: .Jun 24 10:42:24.340 UTC: COA: 10.0.128.38 request queued
191527: .Jun 24 10:42:24.340 UTC: RADIUS: authenticator 7F A9 85 AB F6 4A D0 F3 - B4 E6 F2 56 74 C6 2D 33
191528: .Jun 24 10:42:24.340 UTC: RADIUS: NAS-IP-Address [4] 6 172.20.132.100
191529: .Jun 24 10:42:24.340 UTC: RADIUS: Calling-Station-Id [31] 19 "00:1F:29:7B:BD:82"
191530: .Jun 24 10:42:24.340 UTC: RADIUS: Acct-Terminate-Cause[49] 6 admin-reset [6]
191531: .Jun 24 10:42:24.340 UTC: RADIUS: Event-Timestamp [55] 6 1403606529
191532: .Jun 24 10:42:24.340 UTC: RADIUS: Message-Authenticato[80] 18
191533: .Jun 24 10:42:24.340 UTC: RADIUS: E0 3C B2 8C 89 47 67 A8 69 F5 3D 08 61 FF 53 6E [ <Ggi=aSn]
191534: .Jun 24 10:42:24.340 UTC: RADIUS: Vendor, Cisco [26] 43
191535: .Jun 24 10:42:24.340 UTC: RADIUS: Cisco AVpair [1] 37 "subscriber:command=bounce-host-port"
191536: .Jun 24 10:42:24.340 UTC: COA: Message Authenticator decode passed
191537: .Jun 24 10:42:24.340 UTC: ++++++ CoA Attribute List ++++++
191538: .Jun 24 10:42:24.340 UTC: 06D96C58 0 00000001 nas-ip-address(600) 4 172.20.132.100
191539: .Jun 24 10:42:24.349 UTC: 06D9AC18 0 00000081 formatted-clid(37) 17 00:1F:29:7B:BD:82
191540: .Jun 24 10:42:24.349 UTC: 06D9AC4C 0 00000001 disc-cause(434) 4 admin-reset
191541: .Jun 24 10:42:24.349 UTC: 06D9AC80 0 00000001 Event-Timestamp(445) 4 1403606529(53A95601)
191542: .Jun 24 10:42:24.349 UTC: 06D9ACB4 0 00000081 ssg-command-code(490) 1 33
191543: .Jun 24 10:42:24.349 UTC:
191544: .Jun 24 2014 10:42:24.365 UTC: %EPM-6-IPEVENT: IP 10.2.12.45| MAC 001f.297b.bd82| AuditSessionID AC1484640000026B28C02CDC| AUTHTYPE DOT1X| EVENT IP-RELEASE
191545: .Jun 24 2014 10:42:24.382 UTC: %EPM-6-IPEVENT: IP 10.2.12.45| MAC 001f.297b.bd82| AuditSessionID AC1484640000026B28C02CDC| AUTHTYPE DOT1X| EVENT IP-WAIT
191546: .Jun 24 2014 10:42:24.382 UTC: %EPM-6-POLICY_REQ: IP 0.0.0.0| MAC 001f.297b.bd82| AuditSessionID AC1484640000026B28C02CDC| AUTHTYPE DOT1X| EVENT REMOVE
191547: .Jun 24 2014 10:42:24.390 UTC: %EPM-6-AUTH_ACL: POLICY Auth-Default-ACL-OPEN| EVENT DETACH-SUCCESS
191548: .Jun 24 2014 10:42:26.353 UTC: %LINK-5-CHANGED: Interface GigabitEthernet0/3, changed state to administratively down
191549: .Jun 24 2014 10:42:27.359 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/3, changed state to down
ISE-TEST-SWITCH#
191550: .Jun 24 2014 10:42:36.366 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/3, changed state to down
191551: .Jun 24 10:42:40.592 UTC: AAA/BIND(000002A7): Bind i/f
191552: .Jun 24 2014 10:42:41.129 UTC: %AUTHMGR-5-START: Starting 'dot1x' for client (001f.297b.bd82) on Interface Gi0/3 AuditSessionID AC1484640000026C28C2FA05
191553: .Jun 24 2014 10:42:42.580 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet0/3, changed state to up
191554: .Jun 24 2014 10:42:43.586 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/3, changed state to up
! SESSION ID CHANGES, USER ENTERS CREDENTIALS
! ERROR MESSAGE AT CLIENT "YOUR SESSION HAS EXPIRED"
! ERROR MESSAGE IN ISE "86017 SESSION MISSING"
ISE-TEST-SWITCH#show authentication sessions interface gi0/3
Interface: GigabitEthernet0/3
MAC Address: 001f.297b.bd82
IP Address: 10.2.12.45
Status: Running
Domain: UNKNOWN
Security Policy: Should Secure
Security Status: Unsecure
Oper host mode: multi-auth
Oper control dir: both
Session timeout: N/A
Idle timeout: N/A
Common Session ID: AC1484640000026C28C2FA05
Acct Session ID: 0x0000029D
Handle: 0x2C00026D
Runnable methods list:
Method State
dot1x Running
mab Not runGuest authentication failed: 86017: Session cache entry missing
try adjusting the UTC timezone during the guest creation in the sponsor portal.
86017
Guest
Session Missing
Session ID missing. Please contact your System Administrator.
Info -
Problem with Updating clients with UNIX command
Hi.
Until this day, I used to update all our 50 client macs by manually logging in as administrator via ARD and choosing Software Update from the apple menu, this works always and I use our own servers SUS so the downloading is really fast. Still, this clearly is time consuming and annoying when you have this many clients. I have now done some search and I know I could do this by sending unix command to clients using ARD. First I had problems with running the command, then I noticed I need to run this as root. Then it "works".
Works, not quite. It starts to run, and I can see all the output. I have tried this with few clients and the results are confusing. The following is an output from one client I send the command "softwareupdate -i -r"
SIBELIUS411 (172.17.6.36)
2011-03-25 13:13:20.610 softwareupdate[1692:392b] PackageKit: * Missing bundle identifier: /Library/Receipts/PPDInstallerRI3222E3L.pkg
2011-03-25 13:14:09.636 softwareupdate[1692:392b] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.NetworkUtility"></bundle>
2011-03-25 13:14:09.798 softwareupdate[1692:392b] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.remoteinstallmacosx"></bundle>
2011-03-25 13:14:09.801 softwareupdate[1692:392b] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.server.SystemImageUtility"></bundle>
2011-03-25 13:19:40.016 softwareupdate[1692:903] PackageKit: * Missing bundle identifier: /Library/Receipts/PPDInstallerRI3222E3L.pkg
Software Update Tool
Copyright 2002-2009 Apple
Downloading Safari
Verifying Safari
Waiting to install Safari
Downloading Mac OS X Update Combined
Verifying Mac OS X Update Combined
Waiting to install Mac OS X Update Combined
Downloading Ricoh Printer Software Update
Verifying Ricoh Printer Software Update
Waiting to install Ricoh Printer Software Update
Downloading iWeb Update
Verifying iWeb Update
Waiting to install iWeb Update
Downloading Java for Mac OS X 10.6 Update 4
Verifying Java for Mac OS X 10.6 Update 4
Waiting to install Java for Mac OS X 10.6 Update 4
Downloading iTunes
Verifying iTunes
Waiting to install iTunes
Downloading Remote Desktop Client Update x signature
x RemoteDesktopClient.pkg.tar
x RemoteDesktopClient.pkg
x RemoteDesktopClient.pkg/Contents
x RemoteDesktopClient.pkg/Contents/Archive.bom
x RemoteDesktopClient.pkg/Contents/Archive.pax.gz
x RemoteDesktopClient.pkg/Contents/Info.plist
x RemoteDesktopClient.pkg/Contents/._RemoteDesktopClient.dist
x RemoteDesktopClient.pkg/Contents/RemoteDesktopClient.dist
x RemoteDesktopClient.pkg/Contents/Resources
x RemoteDesktopClient.pkg/Contents/Resources/background.tif
x RemoteDesktopClient.pkg/Contents/Resources/BundleVersions.plist
x RemoteDesktopClient.pkg/Contents/Resources/cleanup_list
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/InstallationCheck.strings
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/da.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/deleteomatic
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/InstallationCheck.string s
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/Dutch.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/InstallationCheck.stri ngs
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/English.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/InstallationCheck.strings
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/fi.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/InstallationCheck.strin gs
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/French.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/InstallationCheck.strin gs
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/German.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Hints.plist
x RemoteDesktopClient.pkg/Contents/Resources/InstallationCheck
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/InstallationCheck.stri ngs
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/Italian.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/InstallationCheck.str ings
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/Welcome.rtfd/icons.pn g
x RemoteDesktopClient.pkg/Contents/Resources/Japanese.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/kickstart
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/InstallationCheck.strings
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/ko.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/makeuser
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/InstallationCheck.strings
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/no.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/package_version
x RemoteDesktopClient.pkg/Contents/Resources/PlistBuddy
x RemoteDesktopClient.pkg/Contents/Resources/postflight
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/cleanStartup.pl
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/copypackages
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/deleteObsoleteFil es
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/learnFiles
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/postflightKicksta rt
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/setupLaunchFiles
x RemoteDesktopClient.pkg/Contents/Resources/postflightactions/setupLaunchFilesRFBEventHelper
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/setupMenuExtras
x RemoteDesktopClient.pkg/Contents/Resources/postflight_actions/stampBuildNumInPl istStrings
x RemoteDesktopClient.pkg/Contents/Resources/postflight_kickstart
x RemoteDesktopClient.pkg/Contents/Resources/postflightkickstartentries
x RemoteDesktopClient.pkg/Contents/Resources/postflightmakeuserentries
x RemoteDesktopClient.pkg/Contents/Resources/preflight
x RemoteDesktopClient.pkg/Contents/Resources/preflight_actions
x RemoteDesktopClient.pkg/Contents/Resources/preflight_actions/cleanAndPreflightK ickstart
x RemoteDesktopClient.pkg/Contents/Resources/preflight_actions/maybeNukeVNCServer
x RemoteDesktopClient.pkg/Contents/Resources/preflight_actions/moveAsideFirewallD efaultPrefsTiger
x RemoteDesktopClient.pkg/Contents/Resources/preflight_kickstart
x RemoteDesktopClient.pkg/Contents/Resources/preflightkickstartentries
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/InstallationCheck.strings
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/pt.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/InstallationCheck.stri ngs
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/Spanish.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/InstallationCheck.strings
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/sv.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/InstallationCheck.string s
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/zh_CN.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/Description.plist
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/InstallationCheck.string s
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/License.rtf
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/Localizable.strings
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/PantherSU.xml
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/ReadMe.rtf
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/SUDescription.html
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/Welcome.rtfd
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/Welcome.rtfd/icons.png
x RemoteDesktopClient.pkg/Contents/Resources/zh_TW.lproj/Welcome.rtfd/TXT.rtf
x RemoteDesktopClient.pkg/Contents/version.plist
Verifying Remote Desktop Client Update
Waiting to install Remote Desktop Client Update
Checking packages…
Installing
Waiting for other installations to complete…2011-03-25 13:20:01.468 softwareupdate[1692:37b7] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.remoteinstallmacosx"></bundle>
2011-03-25 13:20:01.471 softwareupdate[1692:37b7] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.server.SystemImageUtility"></bundle>
2011-03-25 13:20:01.540 softwareupdate[1692:37b7] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.NetworkUtility"></bundle>
2011-03-25 13:20:01.731 softwareupdate[1692:37b7] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.remoteinstallmacosx"></bundle>
2011-03-25 13:20:01.734 softwareupdate[1692:37b7] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.server.SystemImageUtility"></bundle>
2011-03-25 13:20:01.808 softwareupdate[1692:37b7] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.NetworkUtility"></bundle>
Validating packages…
Writing files…
Running package scripts…
Removing old files…
Optimizing system for installed software…
Moving items into place…
Registering updated components…
And thats it, it stops there. Few clients completed the task, but the output says that they skipped the installation of all updates. In the case above, there is some skipping too, and I don't know what it means. Yesterday I left one client to this part where its Registering updated components.... , and today when I came in, it's still there, and the task is still running. When I update the clients with the Software Update from apple menu, it takes usually 10 minutes max to complete the whole process, download and install. After I restarted the same client and ran the manual Software Update from apple menu, it shows the same updates, it didn't do anything???
Am I doing something wrong with the command?I am having the same issue. I send the unix command to some test clients to install all updates. The process never finishes and stays at "Registering updated companents....". (See screen shot)
I have manually restarted some of the clients after waiting a very long time. All updates seem to have been installed. I am wondering why the task hangs at this point. I want to be able to ran ASU with this Unix method on the 450+ macs that I manage at work, but it scares me that the task never seems to finish. -
Problem with multiple client numbers from a view
Hi Gurus,
I have a problem with a view
Creates a view with a UNION ALL stmt
=====================================
Create view vw_benifits
as
SELECT
Client_num, -- can have multiple values like 200,201,250
PERNR,
OBJPS,
ENDDA,
BEGDA,
AEDTM,
UNAME,
COB_MNTH_AMT
FROM
STG_SAP_PA9211_TB
UNION ALL
SELECT
null, -- no client number for legacy data
PERNR,
OBJPS,
ENDDA,
BEGDA,
AEDTM,
UNAME,
COB_MNTH_AMT
from
LEG_STG_SAP_PA9211_TB;
==============================
The second table contains legacy data (LEG_STG_SAP_PA9211_TB). The first table now contains multiple client data (ie the client_num can be 201,202,250 like that.
Now if the users qery the view they will only get that clients data.
eg selet * from vw_benifits where client_num=250 results only client 250 data. But I want to add the legacy data also with that.
I don't want to propose
selet * from vw_benifits where client_num in (250,NULL) since the users will be confused.
Is there any other way to do this . my requirement is like
If they query
select * from vw_benifits where client_num=250, the data should include all the records satisfying client=250 + the records from the legacy data. The view need to be created like that.
Appreciate your help
DeepakHi Thanks for the suggestion.
But I am not sure this may work for me. Here my users may not be able to use that since they don't know Oracle.
I want to hide that details from them
They may just issue a statement like this
select * from vw_benifits where client_num =250
Or
select * from vw_benifits where client_num =400 . But both times I need to show them the data from the legacy table.
Deepak -
WebAccess problem with Windows Client 8
Hi,
We have a problem, with external access with windows 8 client Only, with the following error
The user "user@domain", on client computer "IP:33050", has initiated an outbound connection. This connection may not be authenticated yet.
There's Gateway and Webaccess on the same server
thanks
Rémy
http://www.blogotec.fr MCITP Server Administrator MCTS VirtualisationHi,
Have you tried to turn off Windows Firewall, then test the result again, check whether Firewall is the culprit. Seems the outbound connection is blocked in Windows Firewall, check your Connection Security Rule Properties in Windows Firewall.
Connection Security Rule Properties Page: Authentication Tab
http://technet.microsoft.com/en-us/library/dd448596(v=ws.10).aspx
Yolanda Zhu
TechNet Community Support -
Database connectivity problem with instant client.
Guys,
I've installed the Oracle instant client basic and ODBC files in my system.
But when I create a system DSN and test the connectivity my database connectivity,it fails with
ORA-12637:Packet receive failed error
My TNSNAMES reads below:
ONDSP101.DIGITALINDIASW.NET =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = namesrv1.xy.zz.com)(PORT = 1522))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ONDSP101)
and my SQLNET as below:
AUTOMATIC_IPC = OFF
TRACE_LEVEL_CLIENT = ON
SQLNET.INBOUND_CONNECT_TIMEOUT=20
NAMES.DEFAULT_DOMAIN = na.pg.com
NAME.DEFAULT_ZONE = na.pg.com
SQLNET.CRYPTO_SEED = "kdg:9yv2$-plo*u6b2x!"
NAMES.DIRECTORY_PATH = (ONAMES,TNSNAMES)
NAMES.PREFERRED_SERVERS =
(ADDRESS_LIST =
(ADDRESS =
(COMMUNITY = TCP.xy.zz.com)
(PROTOCOL = TCP)
(Host = namesrv1.xy.zz.com)
(Port = 1522)
(ADDRESS =
(COMMUNITY = TCP.xy.zz.com)
(PROTOCOL = TCP)
(Host = namesrv2.xy.zz.com)
(Port = 1522)
I've placed my TNSNAMES and SQLNET file in the same folder having the instant client files and I've set my TNSADMIN,LD_LIBRARY_PATH and PATH environmental variable to the folder location.
Note:I'm able to connect to the database using SQLplus.
Thanks,
Bhagat12637, 00000, "Packet receive failed"
// *Cause: A process was unable to receive a packet from another process.
// Possible causes are:
// 1. The other process was terminated.
// 2. The machine on which the other process is running went down.
// 3. Some other communications error occurred.
// *Action: If the cause is not obvious, contact Oracle Customer Support.
These days I very seldom use ODBC for Oracle - most recently it was simply to get Enterprise Architect to "talk" to Oracle. I never used it for my client applications (unlike in the fast distant past), so what I know about ODBC is seriously outdated.
Even so, a few comments. :-)
Have you tried creating a user DSN, in case a system DSN somehow works different environment wise?
The above error description sounds like the original TCP connection was successful (i.e. it is not a host unknown or not reachable error). Subsequent packets seem to fails.
To confirm, run the listener on namesrv1.xy.zz.com with logging enabled and have a look at the listener.log - does it show a connection being accepted/handled from your PC when you use the ODBC DSN?
Have you tried the Oracle ODBC drivers? When getting EA connected I had problems (also with Instant Client) and Microsoft ODBC driver for Oracle. Downloaded and installed the Oracle ODBC driver and it worked just fine first time around.
PS. You should raise this topic on the Instant Client Forum instead. -
Problem with Instant Client 10.2 with ODBC and Studio 6.0
Has anyone else had the issue of not being able to make a second connection after the first connection has been closed and the free HENV is called via the object distructor? What actually fails is the second time thru the SQLDriverConnect call returns -1. If the connection object is a global but close is still called it will work. So this leads me to believe the problem might be from the SQLFreeEnv call in the distructor.
If I run test using the 10.1 Instant cleint it works fine. I have included some code that I use to test with below.
I am using:
XP Pro sp2
Visual Studio 6.0 sp6
Instant Client 10.2
MDAC 3.51
Oracle Server 10g
Thank you for anyone suggesting advice, help, direction....
#include "stdafx.h"
#include <afxdb.h>
#include "DriverTest.h"
#include <odbcss.h>
#ifdef _DEBUG
#define new DEBUG_NEW
#undef THIS_FILE
static char THIS_FILE[] = __FILE__;
#endif
static char CONN_STRING[] = "DSN=TMTest2;UID=TMMain;PWD=TMMain1;";
CWinApp theApp;
using namespace std;
CDatabase cdGlobalTMMainDB;
BOOL TestOnStack();
BOOL TestGlobal();
int _tmain(int argc, TCHAR* argv[], TCHAR* envp[])
int nRetCode = 0;
// initialize MFC and print and error on failure
if (!AfxWinInit(::GetModuleHandle(NULL), NULL, ::GetCommandLine(), 0))
// TODO: change error code to suit your needs
cerr << _T("Fatal Error: MFC initialization failed") << endl;
nRetCode = 1;
else
// TODO: code your application's behavior here.
cout << "---------------------- Testing connection as global ------------------------" << endl;
TestGlobal();
TestGlobal();
cout << endl << "---------------------- Testing connection on stack -------------------------" << endl;
TestOnStack();
TestOnStack();
cout << endl << "---------------------- Testing connection as global(again) -----------------" << endl;
TestGlobal();
TestGlobal();
return nRetCode;
BOOL TestOnStack()
CString sMessage;
BOOL bOkay = false;
try
CDatabase cdStackTMMainDB;
// try open connection
cout << "Attempt open on stack... " ;
bOkay = cdStackTMMainDB.OpenEx( CONN_STRING, CDatabase::noOdbcDialog );
// close connection
cdStackTMMainDB.Close();
cout << "Successful" << endl;
catch( CDBException *pX )
CString cszTheStr;
printf("FAILED - CDBException has occurred %s\n", pX->m_strError );
pX->Delete();
catch( CMemoryException *pX )
printf("FAILED - CMemoryException has occurred\n" );
pX->Delete();
catch( ... )
printf("FAILED - Other exception has occurred.\n" );
// return results
return( bOkay );
BOOL TestGlobal()
CString sMessage;
BOOL bOkay = false;
try
// try open connection
cout << "Attempt open as global... " ;
bOkay = cdGlobalTMMainDB.OpenEx( CONN_STRING, CDatabase::noOdbcDialog );
// close connection
cdGlobalTMMainDB.Close();
cout << "Successful" << endl;
catch( CDBException *pX )
CString cszTheStr;
printf("FAILED - CDBException has occurred %s\n", pX->m_strError );
pX->Delete();
catch( CMemoryException *pX )
printf("FAILED - CMemoryException has occurred\n" );
pX->Delete();
catch( ... )
printf("FAILED - Other exception has occurred.\n" );
// return results
return( bOkay );
}For what it is worth, I am having a similar problem with an application I support. When I upgraded from 10.2.0.2 to 10.2.0.3 to fix a performance problem, we now have this connection problem. If I can not get a good solution for the InstantClient I will have to start using the Full 10.2.0.3 Client and I am not looking forward to deploying that.
Steve Hicklin
USA -
Cisco Prime 2.1 problem with API/Client
Hi,
im having a problem with the API output i get from Cisco Prime Infrastructure. The URL im trying to GET info from is:
https://<URL>/webacs/api/v1/data/Clients
The output shows that im missing data from a specific ID. Example:
{"@url":"https:\/\/prime.lmv.lm.se\/webacs\/api\/v1\/data\/Clients\/1280389614","@type":"Clients","$":"1280389614"}
Then i try to GET the info regarding this ID: https://<URL>/webacs/api/v1/data/Clients/1280389614
{"errorDocument":{"httpResponseCode":500,"httpMethod":"GET","message":"No such entity as Clients \/ 1280389614.-PRS-101","id":"presentation.PRS-101","uriPath":"data\/Clients\/1280389614","queryParams":"{}"}}
So something is wrong here, so when i add ".full=true" parameter i get the following error as it cannot show the client data:
https://<URL>/webacs/api/v1/data/Clients.json?.full=true&.firstResult=1000&.maxResults=1000
{"errorDocument":{"httpResponseCode":500,"httpMethod":"GET","message":"Exception while invoking valueOf method 'getEnum' of enumeration class 'class com.cisco.ncs.nbi.client.ClientProtocolEnum'; nested exception is org.hibernate.HibernateException: Exception while invoking valueOf method 'getEnum' of enumeration class 'class com.cisco.ncs.nbi.client.ClientProtocolEnum'","exception":"org.springframework.orm.hibernate3.HibernateSystemException: Exception while invoking valueOf method 'getEnum' of enumeration class 'class com.cisco.ncs.nbi.client.ClientProtocolEnum'; nested exception is org.hibernate.HibernateException: Exception while invoking valueOf method 'getEnum' of enumeration class 'class com.cisco.ncs.nbi.client.ClientProtocolEnum'","uriPath":"data\/Clients","queryParams":"{.full=[true], .firstResult=[1000], .maxResults=[1000]}"}}
Any idea how to solve this issue, how can i find the client that is causing this problem? In my script im reading all the clients in the network to a third party application. But right now its hard to get this output in a smart way. It might be resolved in 2.2, but it feels like the data i corrupt in some way so i doubt that this error is related to the version?
Best Regards // Mattias AnderssonHi,
I have also run into this problem on two different Prime 2.1-systems when trying to get all Client-data available. I haven't figured out a way to fix it more than making small calls (.maxResults=100) then trying to pin-point and skip the ID giving the error. I've been using 2.2 for a while now but haven't tested the Client-API that much yet. I'll experiment some more on it and see if I can recreate the problem to see if it's related to the version.
Maybe you are looking for
-
When installing itunes i get the error message
I tunes could not be installed because visual basic script is not installed or has been disabled i am a bit thick so if anyone could help i would be grateful
-
Alternative Free Good determination in Sales order
Dear Gurus, We activated Free Goods determination. We are maintaining condition records in Tcode VBN1. We are creating the condition records using the fields Sales org, Distribution Channel and Sales Office. Condition record specifies the free good
-
I made the mistake of installing OS 10.9 on my older MacBook Air and the machine has become horribly slow and unpredictable. I visited the Apple store and questioned a 'Genius' about getting rid of 10.9 and reinstalling the previous OS 10.6 for which
-
Error trying to drag/drop import .mov FCP movie to DVD Studio Pro...?
I exported a video from FCP 7 as a .mov with chapter markers to use in DVD studio pro and it gives me this error: Help =[ Process: DVD Studio Pro [1263] Path: /Applications/DVD Studio Pro.app/Contents/MacOS/DVD Studio Pro Identifier: com.
-
Feedback - requests for future sw/hw Enhancements
Landscape documents Landscape keyboard for two thumb support Save documents/pictures/video locally Voice activated dialing Voice recording WMV, AVI conversion support in iTunes Cut and Paste 3G Macro camera support Video capture Instant Message suppo