Problems with USB device when using WindowsNT
Hi,
my problem is that I want to use a simulator which can only be connected with USB to the computer.
I used the VISA Driver Development Wizard as discribed in this link (http://zone.ni.com/devzone/conceptd.nsf/webmain/6792BAB18242082786256DD7006B6416) and it didn't work.
I'm using Windows NT and VISA 3.1 and I read that it isn't possible to create a USB connection with VISA when using Windows NT. So my questions
1) is this right
2) Has someone a idea what I can do? I tried to use VISA USB Control and this also didn't work.
I hope I discribed my problem detailed enough. It's my first post.
Thanks for your responses
Joerg
As you can see in this table, USB is not supported by VISA under NT:
http://digital.ni.com/public.nsf/websearch/EE34F21ECC2BE01286256C52005D1A1F?OpenDocument
I would recommend to use Win2000 or XP. Using one of these OSes you could use this turorial to create your VISA-driver:
http://zone.ni.com/devzone/devzoneweb.nsf/Opendoc?openagent&1D0DD81FF1448CAE86256D90006EE2B4
If it is not posssible to change the OS, you have to look for other ways of programming your usb-device. Check the web or the Microsoft site for help concerning Windows SDK and USB.
Hope this helps a little!
Similar Messages
-
K7N2 deltas mainboards have a problem with usb devices ??
Ok here is my problem..
I had installed WinXP Pro with SP1..
I got a 20 GB USB2.0 disk.i connected it on the both front or rear usb ports.
When i tried to transfer files to my usb disk or to my PC, in the middle of the copying, i got "Write Delay Failed" error and lost my usb connection..
I had to plug it out and in again..
Now, i have an DSL modem..Last night, i was disconnected from internet and my modem's lights gone..I plug it again, no lights..restarted my PC, also completely shutdown Windows XP..Again no lights..
Then, formatted PC and installed windows 2000 Pr and SP4, until now, my modem worked fine..But USB 2.0 ports are still no use for my usb disk...
In bios , it's enabled as USB 1.1+2.0..
I think this K7N2 deltas have a problem with usb 2.0 devices and Win XP Pro..
Some guys talking about, removing 9th wire earth, but couldn't understand which wire from where ? From mainboard or from usd device's cable ?
Those cables are fabricated, i think it's impossible ?
My processor is Athlon 2500+, ram Twinmos 512 DDR 400
Thanks for replyI'm also having this problem. It's happening with my USB flash disk. I was almost buying another one when I tried it with Windows Vista on the same machine and it worked ok, then I tried Arch Linux (with kernel 2.6.30.5) on another machine and got the same error. After that I tried Ubuntu and it worked ok. Seems that Arch's kernel doesn't like my USB flash disk.
Last edited by esdrasbeleza (2009-09-02 01:16:09) -
MSI K8N Diamond - Boot problems with USB devices attached.
Hi There.
I have been seeking the forums, but havent found the answer to my problem yet.
This is how it goes with ANY USB devices attached to either of the four USB ports on the Motherboard.
When i turn on my system, it hangs in the POST right after displaying the BIOS version (Which I have updated to 1.6) - I cant use my Keyboard to get to the BIOS setup.
Without USB devices attached...
The system boots without problems. And in Windows XP SP2 i can insert my keyboard, mouse etc. and everything works great - both USB 1.1 & 2.0 devices.
I have disabled the KB/USB.. in BIOS and I have disabled the "Boot on other device" option as well.
As I have found on this forum, a lot of people have problems with USB Front panel and D-Bracket (USB ports) connectors causing the system to hang - But my D-Bracket (USB connectors) and my front USB port is at this time DISCONNECTED - so this cannot be the problem.
The D-Bracket shows the "Bios Sign On" information - and stops at that point
Am I having a malfunctioning Motherboard here, or are there any solutions to this problem?
Please help me as I am desperate to have my system work properly.
Regards
StieperWell I have read about that somewhere in here, but my problem is NOT with an USB hub, but with any USB device attached to the motherboard's USB slots. It is driving me nuts to be honest!! I think it might be time for RMA
What do you say guys - is my Motherboard ready for RMA, or do I have to try something specific berfore sending it to the retailer?? -
hi guys,
i have a problem with my usb devices.
the dmesg:
Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009
Command line: root=/dev/sda5 vga=0x0361 ro
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
BIOS-e820: 000000007fed0000 - 000000007fee3000 (ACPI NVS)
BIOS-e820: 000000007fee3000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
DMI present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fed0 max_arch_pfn = 0x100000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009f800 (usable)
modified: 000000000009f800 - 00000000000a0000 (reserved)
modified: 00000000000ce000 - 00000000000d0000 (reserved)
modified: 00000000000dc000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000007fed0000 (usable)
modified: 000000007fed0000 - 000000007fee3000 (ACPI NVS)
modified: 000000007fee3000 - 0000000080000000 (reserved)
modified: 00000000e0000000 - 00000000f0000000 (reserved)
modified: 00000000fec00000 - 00000000fec10000 (reserved)
modified: 00000000fed00000 - 00000000fed00400 (reserved)
modified: 00000000fed14000 - 00000000fed1a000 (reserved)
modified: 00000000fed1c000 - 00000000fed90000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000ff000000 - 0000000100000000 (reserved)
init_memory_mapping: 0000000000000000-000000007fed0000
0000000000 - 007fe00000 page 2M
007fe00000 - 007fed0000 page 4k
kernel direct mapping tables up to 7fed0000 @ 10000-14000
RAMDISK: 37d42000 - 37fefc39
ACPI: RSDP 00000000000f7fe0 00024 (v02 PTLTD )
ACPI: XSDT 000000007fedab41 0008C (v01 Sony VAIO 20070418 PTL 00000000)
ACPI: FACP 000000007fee1bd2 000F4 (v03 Sony VAIO 20070418 PTL 00000001)
ACPI: DSDT 000000007fedbeeb 05C73 (v02 Sony VAIO 20070418 PTL 20050624)
ACPI: FACS 000000007fee2fc0 00040
ACPI: APIC 000000007fee1cc6 00068 (v01 Sony VAIO 20070418 PTL 0000005A)
ACPI: HPET 000000007fee1d2e 00038 (v01 Sony VAIO 20070418 PTL 0000005A)
ACPI: MCFG 000000007fee1d66 0003C (v01 Sony VAIO 20070418 PTL 0000005A)
ACPI: TCPA 000000007fee1da2 00032 (v01 Sony VAIO 20070418 PTL 00005A52)
ACPI: SLIC 000000007fee1dd4 00176 (v01 Sony VAIO 20070418 PTL 01000000)
ACPI: TMOR 000000007fee1f4a 00026 (v01 Sony VAIO 20070418 PTL 00000003)
ACPI: APIC 000000007fee1f70 00068 (v01 Sony VAIO 20070418 PTL 00000000)
ACPI: BOOT 000000007fee1fd8 00028 (v01 Sony VAIO 20070418 PTL 00000001)
ACPI: SSDT 000000007fedbc29 002C2 (v01 Sony VAIO 20070418 PTL 20050624)
ACPI: SSDT 000000007fedb159 0025F (v01 Sony VAIO 20070418 PTL 20050624)
ACPI: SSDT 000000007fedb0b3 000A6 (v01 Sony VAIO 20070418 PTL 20050624)
ACPI: SSDT 000000007fedabcd 004E6 (v01 Sony VAIO 20070418 PTL 20050624)
ACPI: BIOS bug: multiple APIC/MADT found, using 0
ACPI: If "acpi_apic_instance=2" works better, notify [email protected]
ACPI: Local APIC address 0xfee00000
(7 early reservations) ==> bootmem [0000000000 - 007fed0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000082d0d0] TEXT DATA BSS ==> [0000200000 - 000082d0d0]
#3 [0037d42000 - 0037fefc39] RAMDISK ==> [0037d42000 - 0037fefc39]
#4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#5 [000082e000 - 000082e204] BRK ==> [000082e000 - 000082e204]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
found SMP MP-table at [ffff8800000f8010] f8010
[ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001200000-ffff880002dfffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007fed0
On node 0 totalpages: 523871
DMA zone: 56 pages used for memmap
DMA zone: 1682 pages reserved
DMA zone: 2245 pages, LIFO batch:0
DMA32 zone: 7108 pages used for memmap
DMA32 zone: 512780 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
PM: Registered nosave memory: 00000000000d0000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
NR_CPUS:16 nr_cpumask_bits:16 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 25 pages at ffff880001010000, static data 72352 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515025
Kernel command line: root=/dev/sda5 vga=0x0361 ro
Initializing CPU#0
NR_IRQS:768
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1994.610 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2053736k/2095936k available (3409k kernel code, 452k absent, 41160k reserved, 1239k data, 464k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 3990.43 BogoMIPS (lpj=6648700)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20090320
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3991.23 BogoMIPS (lpj=6649976)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (7982.67 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
net_namespace: 1888 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE storm detected, transactions will use polling mode
ACPI: EC: missing confirmations, switch off interrupt mode.
[Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0x1800-0x181f]
pci 0000:00:1a.1: reg 20 io port: [0x1820-0x183f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfc404800-0xfc404bff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfc400000-0xfc403fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x1840-0x185f]
pci 0000:00:1d.1: reg 20 io port: [0x1860-0x187f]
pci 0000:00:1d.2: reg 20 io port: [0x1880-0x189f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfc404c00-0xfc404fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x18a0-0x18af]
pci 0000:00:1f.2: reg 10 io port: [0x18d8-0x18df]
pci 0000:00:1f.2: reg 14 io port: [0x18cc-0x18cf]
pci 0000:00:1f.2: reg 18 io port: [0x18d0-0x18d7]
pci 0000:00:1f.2: reg 1c io port: [0x18c8-0x18cb]
pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfc404000-0xfc4047ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 32bit mmio: [0x000000-0x0000ff]
pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xce000000-0xceffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xcc000000-0xcdffffff]
pci 0000:01:00.0: reg 24 io port: [0x2000-0x207f]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:00:01.0: bridge io port: [0x2000-0x2fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xcc000000-0xceffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:00:1c.0: bridge io port: [0x3000-0x3fff]
pci 0000:00:1c.0: bridge 32bit mmio: [0xf6000000-0xf7ffffff]
pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf0000000-0xf1ffffff]
pci 0000:00:1c.1: bridge io port: [0x4000-0x4fff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xf8000000-0xf9ffffff]
pci 0000:00:1c.1: bridge 64bit mmio pref: [0xf2000000-0xf3ffffff]
pci 0000:06:00.0: reg 10 32bit mmio: [0xfa000000-0xfa000fff]
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:00:1c.2: bridge io port: [0x5000-0x5fff]
pci 0000:00:1c.2: bridge 32bit mmio: [0xfa000000-0xfbffffff]
pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf4000000-0xf5ffffff]
pci 0000:08:00.0: reg 10 64bit mmio: [0xfc000000-0xfc003fff]
pci 0000:08:00.0: reg 18 io port: [0x6000-0x60ff]
pci 0000:08:00.0: supports D1 D2
pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:00.0: PME# disabled
pci 0000:00:1c.4: bridge io port: [0x6000-0x6fff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfc000000-0xfc0fffff]
pci 0000:09:03.0: reg 10 32bit mmio: [0xfc100000-0xfc100fff]
pci 0000:09:03.0: supports D1 D2
pci 0000:09:03.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:09:03.0: PME# disabled
pci 0000:09:03.1: reg 10 32bit mmio: [0xfc102000-0xfc1027ff]
pci 0000:09:03.1: reg 14 32bit mmio: [0xfc104000-0xfc107fff]
pci 0000:09:03.1: supports D1 D2
pci 0000:09:03.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:09:03.1: PME# disabled
pci 0000:09:03.2: reg 10 32bit mmio: [0xfc101000-0xfc101fff]
pci 0000:09:03.2: supports D1 D2
pci 0000:09:03.2: PME# supported from D0 D1 D2 D3hot
pci 0000:09:03.2: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfc100000-0xfc1fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
system 00:06: ioport range 0x680-0x69f has been reserved
system 00:06: ioport range 0x800-0x80f has been reserved
system 00:06: ioport range 0x1000-0x107f has been reserved
system 00:06: ioport range 0x1180-0x11bf has been reserved
system 00:06: ioport range 0x1640-0x164f has been reserved
system 00:06: ioport range 0xfe00-0xfe7f has been reserved
system 00:06: ioport range 0xfe80-0xfeff has been reserved
pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x2000-0x2fff
pci 0000:00:01.0: MEM window: 0xcc000000-0xceffffff
pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: 0x3000-0x3fff
pci 0000:00:1c.0: MEM window: 0xf6000000-0xf7ffffff
pci 0000:00:1c.0: PREFETCH window: 0x000000f0000000-0x000000f1ffffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.1: IO window: 0x4000-0x4fff
pci 0000:00:1c.1: MEM window: 0xf8000000-0xf9ffffff
pci 0000:00:1c.1: PREFETCH window: 0x000000f2000000-0x000000f3ffffff
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:06
pci 0000:00:1c.2: IO window: 0x5000-0x5fff
pci 0000:00:1c.2: MEM window: 0xfa000000-0xfbffffff
pci 0000:00:1c.2: PREFETCH window: 0x000000f4000000-0x000000f5ffffff
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:08
pci 0000:00:1c.4: IO window: 0x6000-0x6fff
pci 0000:00:1c.4: MEM window: 0xfc000000-0xfc0fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:09:03.0: CardBus bridge, secondary bus 0000:0a
pci 0000:09:03.0: IO window: 0x007000-0x0070ff
pci 0000:09:03.0: IO window: 0x007400-0x0074ff
pci 0000:09:03.0: PREFETCH window: 0x88000000-0x8bffffff
pci 0000:09:03.0: MEM window: 0x90000000-0x93ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09
pci 0000:00:1e.0: IO window: 0x7000-0x7fff
pci 0000:00:1e.0: MEM window: 0xfc100000-0xfc1fffff
pci 0000:00:1e.0: PREFETCH window: 0x00000088000000-0x0000008bffffff
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci 0000:09:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
pci_bus 0000:01: resource 1 mem: [0xcc000000-0xceffffff]
pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
pci_bus 0000:02: resource 1 mem: [0xf6000000-0xf7ffffff]
pci_bus 0000:02: resource 2 pref mem [0xf0000000-0xf1ffffff]
pci_bus 0000:04: resource 0 io: [0x4000-0x4fff]
pci_bus 0000:04: resource 1 mem: [0xf8000000-0xf9ffffff]
pci_bus 0000:04: resource 2 pref mem [0xf2000000-0xf3ffffff]
pci_bus 0000:06: resource 0 io: [0x5000-0x5fff]
pci_bus 0000:06: resource 1 mem: [0xfa000000-0xfbffffff]
pci_bus 0000:06: resource 2 pref mem [0xf4000000-0xf5ffffff]
pci_bus 0000:08: resource 0 io: [0x6000-0x6fff]
pci_bus 0000:08: resource 1 mem: [0xfc000000-0xfc0fffff]
pci_bus 0000:09: resource 0 io: [0x7000-0x7fff]
pci_bus 0000:09: resource 1 mem: [0xfc100000-0xfc1fffff]
pci_bus 0000:09: resource 2 pref mem [0x88000000-0x8bffffff]
pci_bus 0000:09: resource 3 io: [0x00-0xffff]
pci_bus 0000:09: resource 4 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:0a: resource 0 io: [0x7000-0x70ff]
pci_bus 0000:0a: resource 1 io: [0x7400-0x74ff]
pci_bus 0000:0a: resource 2 pref mem [0x88000000-0x8bffffff]
pci_bus 0000:0a: resource 3 mem: [0x90000000-0x93ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...
Freeing initrd memory: 2743k freed
Simple Boot Flag at 0x36 set to 0x1
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1249997463.944:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 4017
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.2: irq 27 for MSI/MSI-X
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.4: irq 28 for MSI/MSI-X
pcieport-driver 0000:00:1c.4: setting latency timer to 64
vesafb: framebuffer at 0xcd000000, mapped to 0xffffc20010100000, using 8000k, total 14336k
vesafb: mode is 1280x800x32, linelength=5120, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 160x50
fb0: VESA VGA frame buffer device
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 464k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
pata_acpi 0000:00:1f.1: setting latency timer to 64
pata_acpi 0000:00:1f.1: PCI INT A disabled
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 29
ata2: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 29
ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 29
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata1.00: ACPI cmd ef/90:03:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ATA-7: FUJITSU MHV2200BT, 0000004F, max UDMA/100
ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: ACPI cmd ef/90:03:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2200B 0000 PQ: 0 ANSI: 5
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
ata4.00: ATAPI: MATSHITABD-MLT UJ-220V, 1.00, max UDMA/33
ata4.00: configured for UDMA/33
scsi 3:0:0:0: CD-ROM MATSHITA BD-MLT UJ-220V 1.00 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors: (200 GB/186 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected]
Intel AES-NI instructions are not detected.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
rtc_cmos 00:07: RTC can wake from S4
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
udev: starting version 141
sky2 driver version 1.22
sky2 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
sky2 0000:08:00.0: setting latency timer to 64
sky2 0000:08:00.0: Yukon-2 FE chip revision 1
sky2 0000:08:00.0: irq 30 for MSI/MSI-X
sky2 eth0: addr 00:13:a9:c1:09:33
cfg80211: Calling CRDA to update world regulatory domain
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 3:0:0:0: Attached scsi generic sg1 type 5
ACPI: AC Adapter [ADP1] (on-line)
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
ACPI: Lid Switch [LID0]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
ACPI: Power Button [PWRB]
ACPI: SSDT 000000007fedb8e7 0027A (v01 Sony VAIO 20070418 PTL 20050624)
ACPI: SSDT 000000007fedb3b8 004AA (v01 Sony VAIO 20070418 PTL 20050624)
ACPI Warning (processor_throttling-0843): Invalid throttling state, reset [20090320]
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 000000007fedbb61 000C8 (v01 Sony VAIO 20070418 PTL 20050624)
ACPI: SSDT 000000007fedb862 00085 (v01 Sony VAIO 20070418 PTL 20050624)
ACPI Warning (processor_throttling-0843): Invalid throttling state, reset [20090320]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZ00] (58 C)
input: PC Speaker as /devices/platform/pcspkr/input/input4
sony-laptop: Sony Notebook Control Driver v0.6.
input: Sony Vaio Keys as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:29/SNY5001:00/input/input5
input: Sony Vaio Jogdial as /devices/virtual/input/input6
ACPI: Invalid active0 threshold
iTCO_vendor_support: vendor-support=0
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [TZ01] (58 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: Battery Slot [BAT0] (battery present)
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc404800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc404c00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input7
input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input8
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
usb 2-3: new high speed USB device using ehci_hcd and address 3
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
yenta_cardbus 0000:09:03.0: CardBus bridge found [104d:9005]
yenta_cardbus 0000:09:03.0: Using CSCINT to route CSC interrupts to PCI
yenta_cardbus 0000:09:03.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:09:03.0: TI: mfunc 0x01121b22, devctl 0x64
usb 2-3: configuration #1 chosen from 1 choice
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.31 Tue Jul 28 17:52:27 PDT 2009
yenta_cardbus 0000:09:03.0: ISA IRQ mask 0x0cf8, PCI irq 16
yenta_cardbus 0000:09:03.0: Socket status: 30000006
pci_bus 0000:09: Raising subordinate bus# of parent bus (#09) from #0a to #0d
yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge I/O window: 0x7000 - 0x7fff
yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge Memory window: 0xfc100000 - 0xfc1fffff
yenta_cardbus 0000:09:03.0: pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
iwl3945: Copyright(c) 2003-2009 Intel Corporation
iwl3945 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
iwl3945 0000:06:00.0: setting latency timer to 64
ohci1394 0000:09:03.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[fc102000-fc1027ff] Max Packet=[2048] IR/IT contexts=[4/8]
tifm_7xx1 0000:09:03.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
hub 2-0:1.0: unable to enumerate USB device on port 5
iwl3945 0000:06:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
iwl3945 0000:06:00.0: Detected Intel Wireless WiFi Link 3945ABG
iwl3945 0000:06:00.0: irq 31 for MSI/MSI-X
Initializing USB Mass Storage driver...
scsi5 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
input: HDA Intel Mic at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/input/input9
input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/input/input10
usb 5-1: new low speed USB device using uhci_hcd and address 2
usbcore: registered new interface driver hiddev
Linux video capture interface: v2.00
input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/2-3:1.1/input/input11
generic-usb 0003:1058:1102.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-3/input1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
uvcvideo: Found UVC 1.00 device <unnamed> (05ca:1837)
uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
uvcvideo: Failed to query (129) UVC probe control : -32 (exp. 26).
uvcvideo: Failed to initialize the device (-5).
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
phy0: Selected rate control algorithm 'iwl-3945-rs'
usb 5-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input12
generic-usb 0003:046D:C518.0002: input,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1/input0
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input13
generic-usb 0003:046D:C518.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1/input1
fuse init (API version 7.11)
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 2 processor cores.
VBoxDrv: dbg - g_abExecMemory=ffffffffa0f05760
vboxdrv: fAsync=0 offMin=0x1ae offMax=0x125c
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 3.0.4 (interface 0x000e0000).
VBoxNetFlt: dbg - g_abExecMemory=ffffffffa10a9f00
hub 2-0:1.0: unable to enumerate USB device on port 5
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460302564f69]
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
Clocksource tsc unstable (delta = -435934901 ns)
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
EXT3 FS on dm-0, internal journal
scsi 5:0:0:0: Direct-Access WD My Book 1028 PQ: 0 ANSI: 4
sd 5:0:0:0: Attached scsi generic sg2 type 0
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 10 00 00 00
sd 5:0:0:0: [sdb] Assuming drive cache: write through
usb-storage: device scan complete
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 5:0:0:0: [sdb] Attached SCSI disk
EXT4-fs: barriers enabled
kjournald2 starting: pid 1929, dev dm-1:8, commit interval 5 seconds
EXT4 FS on dm-1, internal journal on dm-1:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem dm-1 with ordered data mode
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
Adding 2449872k swap on /dev/sda6. Priority:-1 extents:1 across:2449872k
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
iwl3945 0000:06:00.0: firmware: requesting iwlwifi-3945-2.ucode
hub 2-0:1.0: unable to enumerate USB device on port 5
iwl3945 0000:06:00.0: loaded firmware version 15.32.2.9
Registered led device: iwl-phy0::radio
Registered led device: iwl-phy0::assoc
Registered led device: iwl-phy0::RX
Registered led device: iwl-phy0::TX
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
wlan0: authenticate with AP 00:11:6b:10:2f:bc
wlan0: authenticated
wlan0: associate with AP 00:11:6b:10:2f:bc
wlan0: RX AssocResp from 00:11:6b:10:2f:bc (capab=0x471 status=0 aid=1)
wlan0: associated
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
hub 2-0:1.0: unable to enumerate USB device on port 5
i think the result is, that my bluetooth and webcam isn't working...
can you help me pls.
regards nigg
Last edited by nigg (2009-08-11 14:14:57)I'm also having this problem. It's happening with my USB flash disk. I was almost buying another one when I tried it with Windows Vista on the same machine and it worked ok, then I tried Arch Linux (with kernel 2.6.30.5) on another machine and got the same error. After that I tried Ubuntu and it worked ok. Seems that Arch's kernel doesn't like my USB flash disk.
Last edited by esdrasbeleza (2009-09-02 01:16:09) -
HP Compaq dc5750 SFF boot problem with USB devices installed.
HP Compaq dc5750 SFF
AMD Athlon (tm) 64 X2 Dual Core Processor 3800+
2.00 GHz 1.37 GB of RAM
XP Professional SP2 with latest updates.
HP Compaq Business System BIOS (786E3 BIOS)(ver. 2.36 Rev. A)
This is a problem when a Microsoft web camera is installed prior to the boot up of the computer
The webcam works fine if it is installed after the boot up.
When any type of USB product that does not have an OS is installed in any USB port the computer freezes at the BIOS POST screen and will not finish the POST unless the USB device is removed. If there is an OS on the USB device it boots normally to that device and it also boots normally to the installed OS if the USB device is not installed.
Contacted HP Support and was told to update the BIOS, which I had already done. Then I was told that the computer was out of warranty and I could pay for the service if I wanted help. I agreed to pay if the problem was fixed. This brought a reply that they did not know if the problem could be fixed.
The next day I received an email with Critical Alerts, one showing the BIOS update I had already installed and 2 other non critical updates.
Since HP did not show any interest in fixing this problem I am posting it here to see if anyone else has had this problem.Hi,
Boot into the bios and change the boot priority order and save the setting change. Look under the Storage TAB drop down and then Boot Order. Highlight USB and press enter and then the down arrow to move it below the hard drive. Save the changes when you exit the bios.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
Problem with JMS migration when using Ctrl+C to stop the managed server in cluster
Hi,
I am having a clustered weblogic application running on Weblogic 7.0 SP5. My application
uses JMS as a asynchrous communication. We have MDB which listens to these JMS
messages.
If something is being processed on Managed Server 1 and while the request is in
process, i am stopping the the MAnaged SErver 1 using Ctrl+C.
After this, i go to admin console and migrate teh JTA and JMS. After this, i am
expecting other running Managed Server should restart the incomplete transaction.
But this is not happening. The Managed Serve2 doesn't process the requst.
But when i restart teh MAnaged SErver 1 again, it takes up the same request and
processes it.
Is this a known problem with Weblogic that it doesn't support Ctlr+C case?
Please note that the same thing is working fine when i stop the server using Admin
console(Normal shutdown OR forced shutdown).
Any comments in this regards are apprecciated.
Thanks,
Naresh
Hi,
I am having a clustered weblogic application running on Weblogic 7.0 SP5. My application
uses JMS as a asynchrous communication. We have MDB which listens to these JMS
messages.
If something is being processed on Managed Server 1 and while the request is in
process, i am stopping the the MAnaged SErver 1 using Ctrl+C.
After this, i go to admin console and migrate teh JTA and JMS. After this, i am
expecting other running Managed Server should restart the incomplete transaction.
But this is not happening. The Managed Serve2 doesn't process the requst.
But when i restart teh MAnaged SErver 1 again, it takes up the same request and
processes it.
Is this a known problem with Weblogic that it doesn't support Ctlr+C case?
Please note that the same thing is working fine when i stop the server using Admin
console(Normal shutdown OR forced shutdown).
Any comments in this regards are apprecciated.
Thanks,
Naresh
-
PROBLEM WITH ALT-V WHEN USING CROATIAN KEYBOARD
Hi,
When Typing ALT GR+V (@ sign) in Croatian Keyboard, all the text from clipboard is copied into the text box (as it is pressed CTRL+V) plus the @sign.
There were some bugs filed long back regarding a similar issue for the German keyboard where the customer was using the AltGr key for special characters, same as in our case.
Below is the list of those bugs:
(1) Bug 757614: GERMAN USERS CANNOT USE ALT-GR KEY TO GET SPECIAL CHARACTERS
(2) 666925
(3) 767865
(4) 768658
I have gone through the descriptions and mail chains mentioned in these bugs, and it seems that the issue was fixed in OJDK.
Please go through the above mentioned bugs once to get more details.
It seems that this is not ORMS issue. It seems to be an Oracle Forms or OJDK issue.
Can someone please advise on this as why is this happening. We are using Oracle Forms 10g.
Thanks and Regards,
Ashwini Swaroop PradhanTom Gewecke wrote:
w/ all the keyboards and language settings.
What do you mean by that? The problem being talked about here is an inability to make French accented characters on a German keyboard. What is your problem exactly?
I've posted here because I guess it may be the same bug.
After upgrading I wasn't able to do special characters, including some accented vocals, like "ì", very common in italian language.
Then I've added an english keyboard, removed the italian one and added it again, so the problem with missing accented vocals was solved.
I still have the same problem with special consonants, like "z" and "c": if I hold my thumb on such letters, I have no options like, say, "ż" (such characters are very important for my field (linguistics) and if Apple won't solve this problem I'll be forced to look elsewhere). -
Ibook G4 having problem with airport connection when using secure network
Hi,
I am currently using a brand new Macbook. I am connected wirelessly to a Comcast network through my Netgear Wireless-N 150 router model WNR 1000. The problem I am having is with the 4 year old ibook when I go to use the airport and connect to my existing network it says the password is incorrect. I spent time troubleshooting this with Netgear and basically we found out that the ibook does connect with the network when there is no security at all.
I erased the hard drive on this ibook to prepare it for sale and it is back to the factory settings. Is there some kind of firmware or drivers I am missing to use the airport as described?? I want to be able to show the buyer that the internet works etc. I also may want to install a few things on the ibook before the sale.
Thanks a mil
Message was edited by: omshantiDid you reset the wireless router to see if by default, it has a different
wireless security then, than however it presently is set up?
The question you pose appears to be marked "answered or solved."
When you reinstall an OS X, the setup asks if you have an existing
wireless connection, or if you will be getting a new one; by default,
the setup will make the existing one the automatic one for OS X.
You should not have to add passwords or other, unless there has
been one set in KeyChain or for the specific wireless base in question.
Tiger 10.4.x does not require you to have a set password for wi-fi,
but you will find several levels of secure options available in OS X.
Not sure why your setup and configuration is problematic. Usually,
a totally new OS X installation is without issue. Sometimes, you
may have to administer a base station via Ethernet cable before
some configurations can use it, but an existing network should be
easy, unless it already has a password security in place.
The Mac will work without a password-protected wi-fi internet source;
often it will 'just work' even when moved to a new environment and
a neighbor's network, if not password protected, will appear among
other options in your vicinity and it will be automatically available.
Not sure if any newer OS X update parts, from the Combo update
files to take Tiger 10.4 to 10.4.11, plus others, would help the Mac
connect better to whatever wireless source of internet available.
I've not had that issue, as you state, except for when someone has
a protected network or passwords in place. Mine has passwords to
keep unauthorized neighbors from easy access; just in case.
In remote locations where few neighbors exist who could access wi-fi
from a lone source, no wireless security settings at all, work just fine.
I've done that; and found a little greater range was gained in signals.
And in the city (largest town in state) a computer I'd set up for use in
a password protected wi-fi network - later worked fine and found the
new owner's own wi-fi network without issues; and I had let the OSX
setup assistant do its job. If a local network is protected by WEP or
WPA2, etc with a password, one would be needed to access it. If not,
then the connection should be automatic.
Good luck & happy computing! -
After a fairly recent update, I began having the option to paste text disappear, I've had backspace cause the browser to go back to the previous page while in a text box, and other issues which are apparently a matter of Firefox not recognizing the fact that I am typing in a text box.
After the last update, suddenly YouTube video page URL links no longer translate into links containing the title of the video, and also things like the use of bookend asterisks in order to have text appear in bold typeface no longer work.i have the same problem with the above..firefox is running too slow with the games in facebook..but it runs good when browsing my updates, msgs, photos...firefox is totally opposite of IE..IE is faster with the games and slow while browsing..i love to use mozila but when i do games it really pisses me off...hope you could help me..
-
Problems with My Nano when using Accessories
I bought my nano in November and haven't had any problem with it...until now. For x-mas I got an ITrip and a music station. My Nano doesn't like them. It worked once, and then stopped working. I took my nano to an Apple Store where they reset everything. It worked...for a day and now my nano won't play music through the ITrip or music station! Any ideas because I don't want to reset it and then re-load everything when I want to use my accessories. Thanks!
Nano-4g Windows XP
Windows XPHello Ashers,
Welcome to Apple Discussions.
I don't want to reset it and then re-load everything when I want to use my accessories.
Resetting will not delete songs/photos from your nano. Sometimes there's a glitch in the nano, where you would have to reset:
Resetting iPod
The next time when you plug your nano to your iTrip and music station, you might want to try turning your nano on first. See if that helps.
Gary -
Problem with path length when using oracle drive
Hello!
Does anybody else experience this problem with Oracle Drive?
When I create a deep or nested hierarchy in which the path length is longer than 250 (the limit might be 255) characters, I cannot access the deeper subpages.
Example:"X:\INET\START1\pfadlaengentest\das istein langer ordnername mit etwa 50 zeichen\and this is another veryveryvery long\and this is another veryveryvery lon2\and this is another veryveryvery lon3\and this is another veryveryvery lon4\and this is another veryveryvery lon5".
I can access the page "and this is another veryveryvery lon4" but not "and this is another veryveryvery lon5"
Is this problem due to WebDAV?
What can I do - I think it is a critical error / bug?
Regards Joerg.I opened a service request and oracle support could help me.
The problem is the windows file system: the path length cannot be longer than 256 chars.
There's a workaround with MS-Webfolders.
More information is available via metalink: watch out for SR-Number 5659267.992.
PS: Thanks to Bert
bye :-j (joerg) -
Problem with external monitor when using Windows XP on MBP
Hi All,
I just got a 15.4" MBP, and put Windows XP Home on it using BootCamp. Anyway, the monitor sits above the MBP's screen, as shown below (set up this way through display props, not sure if it matters):
[ ] External Monitor
[ ] MBP Screen
Anyway, some program windows won't drag to the external monitor (Dell 2007FP connected via DVI). An example is AIM. Any idea what it could be? The window shows for about 1/2" on the top monitor, and then it sticks, even though the cursor will continue to move upwards.
Thanks in advance for any advice.
MikeHello Gray:
Welcome to Apple discussions.
It appears from this knowledge base article, that you need a USB keyboard to use Bootcamp:
http://docs.info.apple.com/article.html?artnum=303572
Barry -
Problem with page size when using redirected printer
I have a customer who connects to another customer's network via VPN, then logs into and RDS server running Server 2012.
This customer then opens an Excel file and tries to print it out to a printer that is local to her and of course shows as redirected when looking at Devices and Printers in her login on the RDS server.
The problem is that when going to File / Print on the Excel document, the page size is listed as Custom Size and if you try to select any other size from the list, it won't accept it and stays at custom size. If she selects another redirected local printer,
she can choose whatever page size she wants.
This is not selecting the paper size. She can change that on either redirected printer. So when she is trying to print an Excel file on legal size paper, the print comes out reduced as if it is trying to print on letter size paper even though legal size
paper is selected.
I hope my description is clear enough. If not, please let me know and I'll try to explain further. So I'm trying to find how to fix this one redirected printer (a Brother MFC-7860DW) so that she can change the page size so when the document prints it occupies
the full sheet of legal size paper.
JonathanIs there is a difference in printer driver for working and non-working redirected printers? If yes, can you match it?
Do you see the same behavior if you use Generic Text Only inbox driver?
Thanks
Hari Kumar --- Disclaimer: This posting is provided AS-IS with no warranties or guarantees and confers no rights -
Problems with USB devices after installing X
I have installed an X-Fi Elite Pro on an SB8P Shuttle box running XP Home. I also use this PC for TV capture, and use a Hauppage WinTV-PVR-USB2, which is an outboard encoder. Previously, I had an Audigy 2 SZ. I was using this set-up for about 8 months with few problems.
Since adding the X-Fi card, I can no longer install the Hauppage card into any USB slot. I sometimes get a strange error message from Windows saying that I would get better results plugging the device into a USB 2 slot. Apart from that, the drivers do not install.
This message is very puzzling - all the USB slots on the PC are USB 2, and there are no USB errors appearing under hardware properties. I cannot be completely certain that the X-Fi card is causing the problem, but am aware of another issue reported by other X-Fi users in which the PC will not shut down cleanly if a USB disk dri've is connected. I am also experiencing this problem - EAXModule is reported as hanging. This leads me to suspect that there is some sort of USB conflict associated with the card.
I would appreciate some assistance with this, as it is extremely frustrating.I seem to have fixed the Hauppauge problem by disconnecting the Belkin USB hub that I was also using. Of course, given that I also depend heavily on this device, this might not have totally resolved the issue. Anyway, at least I can conclude that the X-Fi and Win-PVR aren't inherently conflicting.
I hope a fix for the external DVD dri've problem is in the works.Message Edited by rohan_p on 0-2-2006 03:24 PM -
Problem with 'action' attriubte when using 'rendered'
I have something really strange;
I have a JSF page used to insert a record and when inserting is successful, I set a REQUEST scope parameter called 'saved' with a value of 'true' as following:
FacesContext.getCurrentInstance().getExternalContext().getRequestMap().put("saved",true);Now, in the JSF page I already have a <h:commandButton ...> on the SAME previous JSF page used to collect the data :
<h:commandButton rendered="#{requestScope.saved}" action="#{insertionBean.displayNew}" value="Create another"/>As it is shown, the rendering of this button is conditional ONLY after complete inserting. Until now every thing is OK, and the button rendered only as expected, but what is not expected is that when I click on the button the page only reloads and the method in the action attribute is never fired.
Does the attribute rendered have something to do with RestoreView at the server side? Becasue when I DELETE it, the button fires the method, the problem is only when I use it in this scope.
How I can accomplish this goal?!
Thanks for helpful peopleThe value of the rendered attribue is re-evaluated during apply request values phase. So you need to transfer it to the next request using h:inputHidden or, better, t:saveState (so that it also survives validations).
Maybe you are looking for
-
Error while doing patch 7461070
Hi All, I am doing EBS upgrade from 11.5.10.2 to R12.1.1 in RHEL 4.7 environment. I am in the process of applying a patch 7461070. It is giving error as mentioned below:- xdf files are fnd_seed_stage_config.xdf and fnd_seed_stage_entity.xdf Before ap
-
I would like to print out the icon and title of each of my IOS apps to another document for printing and sharing within my family. My son has my old iPod touch so I erased it so he could put whatever games he wants to play on that I used to play wit
-
HT204088 how to refund a payment
Hi, How could i cancel a purchase? Thanks in advance, Mauro
-
Data Loss in Palm OS - Need a Solution
I have a Palm Treo 755p and use PalmOS 6.2.2 daily, running hotsyncs about once a week. Palm OS is like my lifeline the way I use it so much. I use the calendar, to do list and address book with about 5400 contacts. I am running windows xp pro on a
-
I recently downloaded a few free presets for the magic bullet looks builder. Everything downloaded but for whatever reason the downloaded file won't open in the Looks window. Right now I have them in their own folder. Any idea of how to get them into