Programatically setting the IP address of a 8234 ethernet port in a specific PXI slot

Hi, I have a system with multiple 8234 ethernet cards in a PXIe chassis. Each port has its own subnet and IP address. I need to ensure that the user never has to swap ethernet cables from port to port after a 8234 card is replaced. I.e., how do I programatically set the IP address and subnet of a specific port in a specific slot?
Any comments welcome.

Hi ROgelio,
You are right there is no way to assign IP address to physical interface.
ace-4710-1/Admin(config)# int gigabitEthernet 1/1
ace-4710-1/Admin(config-if)# ip ?
% invalid command
cdn-ace-4710-1/Admin(config-if)# ?
Interface config commands:
carrier-delay Set port up delay value
channel-group Map physical port to port channel
description    Interface specific description
do             EXEC command
duplex         Configure duplex operation
end            Exit from configure mode
exit           Exit from this submode
ft-port        Make physical port specific for Fault Tolerance(FT)
no             Negate a command or set its defaults
qos            Configure QoS operation
shutdown       Shut down the interface
speed          Configure speed operation
switchport     Set switching mode characteristics
So there is no option to configure an IP address on physical interface.
regards,
Ajay Kumar

Similar Messages

How to set the IP address in L25 Tape library

I try to set the ip address in L25 tape library. But it is not stored in the NVRAM. For that purpose I restart the device. Then all the values are reset. please tell how to set the ip address.

Lylee,
Please take a look at the following links. The first describes how to distribute your application to multiple targets when using shared variables. The others are explaining alternate ways to change the IP address of a controller.
How Do I Distribute a Real-Time Application with Shared Variables to Multiple Users?
http://digital.ni.com/public.nsf/allkb/20C9771687E6BBB3862570E7006C2284?OpenDocument
How Do I Change the IP Address of a RT Series Controller (FieldPoint, cRIO, etc) that is not on the Local Subnet?
http://digital.ni.com/public.nsf/allkb/9F7548F5C781E05586256C75006D8B94?OpenDocument
Real-Time Target System Replication Tool
http://digital.ni.com/public.nsf/allkb/444A6A22A6EC50FB86257213004A878C?OpenDocument
http://digital.ni.com/public.nsf/allkb/DDD15965085446E68625733A00451C7A?OpenDocument
Can I Programmatically Assign an IP Address to My Real-Time Target?

Setting the From Address for Reply in Mail

I am having trouble setting the default “From” address for replies in Mail. When I click on “Reply” the new window opens with a default mail address I do not wish to use. This can be changes by going into the drop down box and setting a different one. This is time consuming and it is easy to send from an inappropriate address.
“Help” menu says that the default address ( top one in the drop down box) can be changed and gives these instructions:
Set the From address
Your messages are sent from the account of the currently selected mailbox. If you have multiple email accounts, you can specify a different account to use for sending all messages, or select an account just for the message you’re writing.
To specify the account to use for sending all messages, choose Mail > Preferences, click Composing, and then choose an account from the “Send new messages from” pop-up menu.
To specify an account just for the message you’re writing, click the From pop-up menu, and then choose an email address. To change the order in which addresses are listed in the pop-up menu, reorder the addresses in the “Email address” field in the Account Information pane of Mail account preferences.
When I open the Mail Account Preferences and go to Account Information there is no list of addresses in the “Email address” just the one for the particular account highlighted in the left column eg. “[email protected]” or “[email protected]” .
I tried to move the order of the accounts in the left hand box but nothing wants to move. Clicking and holding to push one account over another seems not to work.
Anyone got any ideas on how to fix this?
NB: This is about "Reply". Default for "New Message" is setting fine.

i found out how to do this finally!
1) set up google gmail account to forward your emails to (from the [email protected])
2) go to your gmail account
3) go to settings (cog in right hand corner)
4) go to 'accounts and import'
5) go to 'send mail as'
6) click 'Add another email address you own' - add your [email protected] address
7) google will send a verification email with code to that email address.
8) enter code
9) go back to gmail account >'send mail as' and select 'make default'
10) close mac 'mail' program and reopen it.
as long as you have gmail account selected as the primary account in MAIL - mail will now come throught as being sent from that [email protected] address!!

Unable to set the ip address for hosted network client after creating WIFI hotspot

Original Title: INTERNET CONNECTIVITY PROBLEM WITH MY LAPTOP WIFI HOTSPOT
HI all
I am able to use internet connection from my lap hotspot, when the internet source is Public or private wifi.
so I know the cmd window commands for hotspot and settings of client(sharing to hosted network client, assigning IP address etc.,)
but the problem I am facing is slight different
I am using my cdma wireless broadband datacard as my source internet connection(Reliance netconnect +)
when I try to create hotspot for this, as usual I am able to create the hotspot and able to share the internet to hostednework client.
but I am unable to set the ip address for hosted network client, if I try to set ip 192.169.137.1 and 255.255.255.0
as soon as I close the window, the ip address also disappears
when connect my android phone to that hotspot, it is able to connect but there is no internet connectivity.
when I check the hostednetwork client for packet transmission, both sent and received packet is happening., I mean transmitting
so what cause the failure in internet connectivity but success in hotspot connectivity?
check the screen shots...
can u help me..
its little complicated

Hi,
Please make sure the Ad hoc connection IP adress is at the same range with your local connection. In addition, how about recreate the ad hoc connection for test, please have a try.
If problem persists, please use Network troubleshooter in Action Center to fix this problem for test.
Roger Lu
TechNet Community Support

I want to set the IP address back to default on a HP LJ 4000n how do I do that?

I want to set the IP address back to default on a HP LJ 4000n how do I do that? The I/O would not let me or maybe just don't know how.

to do that, power off the printer and then press the Select button and power on, maintain the select button during start up.
But after that, I don't know how to setup a new IP adress
dwalker2 wrote:
I want to set the IP address back to default on a HP LJ 4000n how do I do that? The I/O would not let me or maybe just don't know how.
dwalker2 wrote:
I want to set the IP address back to default on a HP LJ 4000n how do I do that? The I/O would not let me or maybe just don't know how.
, is anybody can help us?

How to change the mac address of thunderbolt to ethernet adapter?

Hello everyone,
I am using Macbook pro retina display 2013 version. I have bought a thunderbolt to ethernet adapter in order to connect my Macbook to LAN. But in my area there is a shared line and I have to clone their mac address to my Macbolok. I could not change the mac address of my thunderbot to ethernet adapter. Can anyone please tell me how to change the mac address of thunderbot to ethernet adapter step by step??
Thanks in advance.

Open terminal and type the followings;
1) sudo ifconfig bridge0 ether xx:xx:xx:xx:xx:xx(it will be your new mac address)
2) Type your password to confirm
3) ifconfig bridge0 |grep ether (to see if change is successful)
PS: *This should with your thunderbolt adapter, but its not working usb to ethernet adapters without installing required drivers.
** You may need to do these steps every time you boot your mac.

How to set the DCM snmp trapping to a customized port

Hi There,
Anyone know how to set the DCM SNMP trapping to a customized port?
The default port for SNMP should be 162 while my OSS team requies it be set as a customized port number for load balancing. Can't find a clue in the manual, any idea?
Thanks,

Hi Kim,
The DCM only support the standard SNMP port.
Regards,
Ray

I am using SURPLUSMETER :) I am also using Apple Airport Time Capsule as my Router that is connected to my Satellite dish Internet Modem ... Now on the Surplusmeter I have the option for PPP Modem . Ethernet Port , Airport , Network Card ,

I am using SURPLUSMETER I am also using Apple Airport Time Capsule as my Router that is connected to my Satellite dish Internet Modem ... Now on the Surplusmeter I have the option for PPP Modem . Ethernet Port , Airport , Network Card , & Adaptor .
Which one can I use properly to monitor all the wireless Devices in my hous

Actually, none of the options will do what you are looking for it to do. That is because, this application only monitors the traffic from the device it is hosted on. That would also mean that you would have to run a copy on each computer that will access the Internet on your network; note their individual usages, and then, combine them to get an idea of the total usage.
However, if you are only interested in the amount of Wi-Fi traffic that only your computer is seeing, then the "AirPort Network Card" option would be the correct choice.

PowerShell: How do I reliably set the IP address on an interface when the interface is not connected ?

Hello all,
I am in a bit of a bind - no pun intended. I would like to know how to reliable set the persistent IP address of an interface that may be disconnected when the address is set. I can set an address and it will be stored in the ActiveStore but
that does not really help if I need it next time I reboot. I have tried using netsh and WMI but they don't seem to create a persistent address on the disconnected interface. Now if I us ncpa.cpl I can do it all day long so it must be possible.
In fact if I do it that way the registry settings change. So, I figured I would go that route (modifying the registry) but, alas, that does not work either - upon reboot the address shown in the interface properties show a blank IP address, gateway,
and netmask. It is interesting that it is using a static address though.
Thanks for your help
Robert
Robert Thompson

Look in the Gallery for numerous examples of setting a static address on an interface.
http://gallery.technet.microsoft.com/site/search?query=static&f%5B2%5D.Value=static&f%5B2%5D.Type=SearchText&f%5B0%5D.Value=networking&f%5B0%5D.Type=RootCategory&f%5B0%5D.Text=Networking&f%5B1%5D.Value=clientside&f%5B1%5D.Type=SubCategory&f%5B1%5D.Text=Client-Side%20Management&ac=2
¯\_(ツ)_/¯

Dell 968w..how do I set the IP address for network printing?

Attempting to connect my Dell 968w to the network for access by my HP and Dell laptops. Dell said I need an IP address for the printer..how do I set the address???

you need to contact dell printer support for this info...this is usually done by printing a network config page on your printer & you'll see the printer ip address there.
Note:
Although I work for HP Imaging & Printing
Group , I am speaking for myself and not for
HP.
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

Newbie iPhone: How do I programatically set the text of a UIBarButtonItem?

Hello,
This is probably really more of a question on IBOutlets but here goes. I want to have an updateable label on my Toolbar. A label doesn't seem to "stick" on the toolbar so I figured I would drop a UIBarButtonItem on it and then just update the Title property of it to change the text as I needed. Problem is I can't figure out how to get a reference to the UIBarButtonItem in my code.
With a pure label control, I can drag from the File's Owner to the label in my view to make it an outlet for my ViewController and then access the text property of the label in code. With the UIBarButtonItem, I can't make it an outlet. I know the button is more of an action thing but I don't need to respond to taps, I just want to change the text.
Thanks for any help,
Tom

Tom,
You should be able to assign the UIBarButtonItem to an outlet as long as:
1) you have defined an instance variable in FilesOwner of UIBarButtonItem and prefixed it with "IBOutlet".
2) FilesOwner is set to your custom view controller in the Interface Builder's Inspector panel. If it still thinks it's a standard UIViewController it won't pick up your custom outlets.
All that being said, I'm not sure you can change the title without using a custom view. The default UIBarButtonItem has an initWithTitle: initializer that may be static (perhaps others know of a way to change it once set). But you can define a custom view for the button. That gives you the ability to add a UILabel and programmatically set the text of the label.
Cheers,
George

ADF 11g: Possible to programatically set the pivot handle label ?

Hi all,
I am using JDev/ADF 11.1.1.3. I have a pivot table and I would like to dynamically set the pivot handle labels. The value needed for the label is another column in my view object.
I tried 3 different approaches to no avail and I am running out of ideas:
1) I tried to override the createViewRowAttrHints method as per Steve's article (http://blogs.oracle.com/smuenchadf/examples/#137). While I could see that it did work in the BC tester, it did not get picked up by the pivot table
2) I tried to set the value in the page definition but the itemLabel tag seems to only accept a literal
3) Lastly, I tried the setLayerMetadata method in the underlying DataDirector, still no dice.
If anyone could point me in the right direction, it would be greatly appreciated.
Thanks,
Michel

Hi Dharmathej,
Wht Jdev version u using....... since in JDeveloper 11.1.1.4 ADF provides to hide the status bar of the panelCollection
refer here http://ramadf.blogspot.com/2011/01/jdeveloper-11114-af-panelcollection.html
Regards,
Suganth.G

How do I programatically set the date and time of my FP-2000 in LabVIEW RT?

I checked out the following knowledgebase document which has a tool for setting the system time, but I also need to set the date:
http://zone.ni.com/devzone/explprog.nsf/ 6c163603265406328625682a006ed37d/ 37175dbc3696a1ac86256a850051097d?OpenDoc ument
How can I do this?
-Jim

That is great, Steven. I also found a solution using GetSystemTime and SetSystemTime which are functions in kernel32.dll that get and set the system date-time. This function call worked on the FP-2000 that I have and should work on RT-Embeded systes, as well.
-Jim
Attachments:
GetSystemTime.vi ‏16 KB
SetSystemTime.vi ‏14 KB

Dynamically set the soap address for web services

Hi,
I am developing an Oracle J2ee1.3 web service for Oracle application server 10.1.2.
The web service needs to be deployed on to multiple servers. Hence the host and port for the soap:address needs to be changed for each server.
Eg: For the 1st server the soap:address is http://www.server1.com/test/MyWebService
For 2nd server the soap:address is http://www.server2.com/test/MyWebService
Is there any way to dynamically change this address based on the server the Web Service is deployed to?
Any help is highly appreciated.
Thanks,
Subashini

It helps to post a link to a thread when you refer to it. If you are trying to implement that solution though, you can look at the parameter of the corresponding method being called. The parameter has type 'SIMPLE' which means that it is compatible with all of the predefined elementary ABAP types. In this case, you should use 'STRING'.

I would like to programatically set the "Date Unused" on X Scale formatting for time plots.

I can use the X Scale formatting on the front panel, but when I change from time to decimal using property nodes the "date" keeps showing up. How can I turn the date feature off so I just see Time in HH:MMS format?

Disregard. I found the answer. Set the XScale.Format value to 6 (relative Time). feed in total seconds from start of day to the Xo, The reciprocal of data frequency to DeltaX, and set the decimal resolution to 3. This results in a time tagged plot showing just time (no Date).

Programatically setting the IP address of a 8234 ethernet port in a specific PXI slot

Similar Messages

Maybe you are looking for