PVDM2-12DM compatibility with HWIC-1CE1T1-PRI

                  Hi there,
I'm hoping someone can assist.  The setup i am trying to get working is the following
User dials in over POTS to an ISDN30 Line.  The ISDN30 line (3rd Party Supplier) is connected to our 2911 via a HWIC-1CE1T1-PRI module.  We have inserted a PVDM2-12DM into the router to handle the POTS call.
Problem we have is that we cannot seem to get a modem tone when the user dials in.  The ISDN line connects and the debug modem command shows the modem SETUP & INIT phase - see below
Aug 13 12:58:52.341: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x1, cause=0x0, dchan_idb=0x2B2C837C
Aug 13 12:58:52.341: CSM: called_number 'number removed' modem_pool 2AA6CE14 deny_call FALSE
Aug 13 12:58:52.341: CSM: Next free modem = 0/202; statbits = 10020
Aug 13 12:58:52.341: Modem 0/202 CSM: modem is allocated, modems free=-1
Aug 13 12:58:52.341: Modem 0/202 CSM: Incoming call from Unknown to 'number removed', id 0x61
Aug 13 12:58:52.341: Modem 0/202 CSM: (CSM_PROC_IDLE)<--ISDN_CALL
Aug 13 12:58:52.453: CSM: MODEM_REPORT from 0/0/0:0, call_id=0x61, event=0x4, cause=0x0, dchan_idb=0x2B2C837C
Aug 13 12:58:52.453: Modem 0/202 CSM: MODEM_REPORT rcvd DEV_CONNECTED for call_id 0x61
Aug 13 12:58:52.453: Modem 0/202 CSM: (CSM_PROC_MODEM_RESERVED)<--ISDN_CONNECTED
Aug 13 12:58:52.453: Modem 0/202 CSMV12: SETUP(Answer) ISDN 0/0:0
Aug 13 12:58:52.453: Modem 0/202 CSMV12: configured for Answer(A-law) mode, with Null signaling, 0x0 tone detection
Aug 13 12:58:52.453: Modem 0/202 CSMV12: INIT(Answer) ISDN 0/0:0
Aug 13 12:58:52.453: %ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to N/A N/A
Aug 13 12:58:52.485: CSM: csm_modem_event called
Aug 13 12:58:52.485: Modem 0/202 CSM: (CSM_PROC_WAIT_FOR_CARRIER)<--CSM_EVENT_MODEM_SETUP Aug 13 12:58:52.341: CSM:
but there is no modem tone or any more output from the debug commands.
The ISDN line is working fine as a normal ISDN dial in is successful.
Has any one tried this before or is there a known issue with this solution?

Updated the IOS but made no difference.  Turns out i was missing the line 'network-clock-participate wic 0'  Added this to the config and managed to get incoming POTS calls.  Only problem now is that the PITS call won't stay up for more than 5 seconds.  Looking at the Modem AT registry settings.

Similar Messages

  • Can HWIC-1CE1T1-PRI support voice applications

    The product sheet and another helpful forum post clearly states that the HWIC-1CE1T1-PRI does NOT support voice applications on the PRI, only data applications. However, running 15.2(1)T when we configure a PRI group, it seems to imply that it can support a voice application with a command option to the PRI-group.
    dal-rtr02(config-controller)#pri-group timeslots 1-24
    %PRI-group is created for data application only.
    %For voice application, please remove this pri-group, then configure pri-group again with voice-dsp option.
    What gives? I cannot find this command documented anywhere. What does the "voice-dsp" option for the "pri-group timeslots" do?
    Should we assume this card can STILL not be used for SIP/TDM Voice gateway services?
    Thanks for any tips/confirmation you can provide.
    Kris

    Understood, but what is this "voice-dsp" option for on the end of the "pri-group timeslots" command?
    This seems undocumented.
    The router output is confusing and implies you could use the "voice-dsp" option to enable voice application. What is this all about? Best ignored I guess. The customer is now buying the correct hardware.

  • X.75 ISDN test setup with 2811 and PVDM2-12DM modem

    Hi all,
    We have a customer that requires ISDN-X.75 connection as a back-up for IP. This is used by emergency services that require redundancy. We have to build a test set-up. We have two routers with the modem cards and with                 HWIC-1CE1T1-PRI=  cards. We need to build a test set-up to simulate an incoming call. With ISDN-V110 we could use one of the routers to place an outgoing call to the other router. This set-up is not possible with X.75, since the card can not dail out. What would be the best/cheapest/simplest approach to build this test set-up?
    My involvement in this project is to build a Perl script that collects data via IOS using expect. If someone has the procedure to collect the calling and called line information for a connection with an example I would be very grateful. Our routers run Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3).
    For V110/V.34 and X.25 the tty/vty is collected by issueing a show tcp to relate an IP connection that is created to the tty/vty. The tty/vty port is  then correlated to the calling and called line id.  This is done with show x25 vc for X.25 or show modem csm for V.110/V.34. We need something similar for X.75 to distill the calling and called line IDs for a given TCP connection.
    Thanks in advance!

    It colud be Hardware(Digital Modem Module ) problem.
    Try this link:
    http://www.cisco.com/en/US/products/ps6441/products_feature_guide09186a00806b941f.html#wp1068376

  • 2811 w/ NM-1CE1T1-PRI & PVDM2-36DM - Modem lines being marked "B" Bad

    We recently setup a new 2811 router (IOS 15.0(1)M7) for remote dialup access. It has a ISDN PRI network module NM-1CE1T1-PRI and a 36 port Digital Modem Module (PVDM2-36DM) installed to receive the inbound modem calls.
    When the router is booted up, inbound remote dialup connections work fine for several hours. Then the router digital modem lines begin to stop working. For example, an inbound call is made but the modem tone does not answer. However a "show modem call-stats" shows that a line becomes active with a "*" symbol. When the call is hung up, the line remains in an active "*" state. Eventually the state changes to a "B - Modem is marked bad and cannot be used for taking calls". This symptom will repeat itself with each new inbound call until all of the lines are marked "B". Only a router reboot will temporarily correct the problem.
    Additional symptom, "show modem version" changes to "NiOS Not Responding".
    #sh modem ver
    Slot 0:
    PVDM 1: PVDMII-36DM - HW Version 1, FPGA Version 3.3, NiOS Not Responding
     Modem 0/386-0/397:
        PCI Classid: 0x07800001 Bootrom Rev: 0x00005601 Diag Result: 0x0000007F
        Firmware: Exp_V3_12_2
     Modem 0/398-0/409:
        PCI Classid: 0x07800001 Bootrom Rev: 0x00005601 Diag Result: 0x0000007F
        Firmware: Exp_V3_12_2
     Modem 0/410-0/421:
        PCI Classid: 0x07800001 Bootrom Rev: 0x00005601 Diag Result: 0x0000007F
        Firmware: Exp_V3_12_2

    Hi Ismel,
    Modem firmware looks good to me but you can still try a firmware upgrade to V3_12_3.
    If it is random number selection of bad modem then I suspect that it's an ISP issue and B-channel of ISP while termination of call, leaving the modem in Bad state.
    HTH
    Amit

  • Are Modules PVDM2-12DM and VWIC2-1MFT-T1/E1 supported between each other?

    Hello everyone!
    I have Cisco 2911 with c2900-universalk9_npe-mz.SPA.152-2.T.bin.
    Here is question: module PVDM2-12DM is supported with module VWIC2-1MFT-T1/E1?
    Because I can not configure digital modem to accept call from E1 with error message: ISDN Se0/0/0:15 **ERROR**: accept_incoming_csm_call: modem problem Service denied(0xD): b channel 2, call id 0x16.
    Thank you for answer!

    No.
    The supported modules are described in the PVDM2'DM data sheet, and software release notes.

  • Difference between NM-1CE1T1-PRI and NM-HDV2-1T1/E1

    please if any one can give me the difference between NM-1CE1T1-PRI and NM-HDV2-1T1/E1

    Hi Ahmad,
    NM-1CE1T1-PRI does *not* support voice. Please refer to the following urls:
    Cisco E1/T1 ISDN PRI Network Module - Data Sheet
    http://www.cisco.com/en/US/products/hw/modules/ps2797/products_data_sheet09186a0080189f95.html
    Voice Hardware Compatibility Matrix (Cisco 17/26/28/36/37/38xx, VG200, Catalyst 4500/4000, Catalyst 6xxx)
    http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml
    Relevant Interfaces and Modules
    http://www.cisco.com/en/US/products/ps5855/products_relevant_interfaces_and_modules.html
    -Vaibhav

  • Windows 8 and itunes 11 compatibility with an ipod

    I have itunes11 and Windows 8. I've called Apple and I've talked to Microsoft. This was months ago. I can download itunes and run it from my laptop but am unable to sync my ipod. I get an error and it automatically reboots my computer. I was told there were known compatibility with itunes and Windows 8.  This was months ago.
    I know how to downgrade itunes to XP or Win 7. This is not the issue. I can download to my laptop and place, it will not sync to my ipod device (which is a fear years old), but when I did talk to support I was told that it was supported. The ipod was not the issue.. It was the incompatibility between the programs.
    I see recent updates in the support community in the past month about production resolution but this still has not resolved my issue. I don't believe purchasing a new ipod is going to resolve the issue either.
    If anyone has successfully developed a workaround or recently downloaded itunes11 w/ Windows 8 and can sync to an apple ipod I would love to know how you did it.
    Kia
    [email protected]

    Im not sure that will solve the issue I have with itunes. I have a lenovo laptop and I think it's just an issue with Apple who has to modify the program for users of Windows 8 so that itunes can be used and to find purchased music. I found the music I purchased through itunes but it's not the full tracks. It said it allows me to download it fully so I can hear the whole track, but needs some kind of capatibility? I have no idea what the problem is. If someone has the answer knowing my computer brand and having windows 8 compatibility issues, please let me know what you suggest.

  • Is adobe photoshop cs2 compatable with windows 8?

    Is adobe photoshop CS2 compatable with windows 8?

    I have removed and re-installed CS2 twice now and still get the same library application error.
    DO NOT INSTALL WINDOWS 8 ONTO YOUR COMPUTER IF YOU WANT TO KEEP CS2!
    Telling us to spend more money to upgrade our software to meet OS does not show trust to the users. CS2 should be able to work with new OS systems and if not users should be allowed to update their current program for free to be able to use it on the new OS.
    Thank you,
    Eric

  • I have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3

    i have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3.
    the problem is best explained on the following one - page thread: 
    https://discussions.apple.com/thread/3951518?start=0&tstart=0
    (Clearly i'm not alone in this problem, although i think i figured out what's going wrong a little more than he did...read on!)
    his solution, to put mainstage in jump mode, is very unsatisfactory to me, as it bounces all of a sudden to drastically different settings.
    basically, my analysis is that my controller is NOT receiving MIDI date from mainstage.  in other words, mainstage knows what my controller is doing, but my controller doens't know what mainstage is doing.
     let's say i turn the knob all the way to the right ... 127...and the virtual fader goes to the right like it's supposed to. 
    now...next...let's say i change to a different patch, where that same VIRTUAL fader is not at the max clockwise position..maybe it's only at 1pm.  now when i turn the physical knob to the RIGHT, the midi data is still at 127 on the controller!  it didn't "reset" to sync up with the new level (say 80 or so) setting on the new patch.  so i can't increase that new setting of 80 by continuing to turn the knob to the right.  i have to turn it all the way to zero,...and then continue PAST zero until the controller thinks that IT is at 0...at that point the controller and mainstage are in agreement, and things work fine....so bascially, the keyboard thinks the level is at max...but mainstage thinks the level is at 1pm.
    i am using Logic 9, and i have a macbook pro 2.9 Ghz I7 with 8 gigs of memory and OS X 10.8.4

    Hi Josh,
    Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
    Thanks.
    Mike Towns

  • I have an ipod touch second gen, how can i download the facebook app if it says its not compatable with my current iOS?

    i have an ipod touch second gen, how can i download the facebook app if it says its not compatable with my current iOS?
    i had the facebook app but i could never upgrade it and i was ok with using the outdated version but when i reset the ipod so i could gift it to a friend it obviously got rid of the app and now i cant downloaded because it says its not compatable, how can i download the version i had before i reset it?

    Your only way is if you have the version that was compatible on your computer such as in the recycle bin/trash or in a computer file backup. In that case delete the current version that is in your iTunes App library and replace it with the older version. Then sync.
    Also see:
    Recover Older Versions of iPhone Apps After Updating — Apple News, Tips and Reviews

  • Itunes 9.1 not compatable with XP?

    Tried to download 9.1 and keep getting error message that says: The software you are installing has not passed Windows Logo testing to verify its compatibility with Windows XP. Continuing installation of this software may impair or destabilize operation of your system either immediately or in the future.
    I have reboot computer several times, etc. Have never had a problem with any updates to itunes or iphone till now.
    Thoughts?

    Itunes 9.1 is definitely NOT compatible with Windows XP at this time. The culprit appears to be the Bonjour services package. I recently attempted to install via 3 methods: through Apple Update, via direct download over wireless and via direct download over wired connection. The result was the same in all three instances: when attempting to start itunes 9.1, it would immediately crash with a message "Itunes has encountered a problem and needs to close...". Upon checking the application event viewer (control panel > performance & maintenance > administrative tools > event viewer) I was able to determine that the itunes crashes were due to Bonjour in all but one instance. Bottom line: steer clear of itunes 9.1 until Apple gets their comparability issues corrected.

  • HELP printer compatability with computor.

    Help...Have hp psc 1310  hp officejet 4200 series......Got a new gateway which is Vista and my old one was XP......my printer will print, but can not scan and tried to program the cd in again and computor would not accept it.  Will I need to get a new printer that is compatable with Vista?   Any thing to update of just have to get new?
    thanks enhelder
    Message Edited by enhelder on 07-07-2009 10:51 AM

    Hello Highcountryhike,
              Thank you for posting your request.  You should have no issues updating to 10.10 Yosemite.  Below are a couple links that should help.
    If you run the Software Updates from the Apple Menu, to check for updates.  Some have had issues not seeing updates, so simply click on "Store" from the top menu, and then click on Reload Page".  Select to install HP Updates to ensure you have the latest drivers.
    In some instances, the printer can be updated in the printer queue to resolve other issues, so check to make sure that the printer is listed with the HP Printer Series driver and not just AirPrint.  System Prefernces/Printers & Scanners/ select your printer on the left and check on the right side under "Location:" that Kind: is the printer series.  You can also click the "-" symbol to remove and then re-add the printer queue again, choosing the HP Printer series name to install the drivers.
    Installing the Full Feature HP Printer Driver in OS X v10.10 Yosemite
    Mac OS 10.10 Yosemite and HP Printer Support
    Please post back with any further issues/questions.
    Thanks,
    Double-U-Dee
    Don't forget to give Kudos where Kudos is Due - OR - if a Response Resolved your Issue, Click the "Accept as Solution"
    I am an HP employee, but my posts and replies are my own and do not reflect the opinion of HP.

  • I want to upgrade to Lightroom 5, but I'm concerned about compatibility with my 2008 intel Core 2 Duo iMac with only 4G of Ram.  Will I be able to run Lighroom 5 if I upgrade from Snow Leopard to Lion?

    I want to upgrade to Lightroom 5, but I'm concerned about compatibility with my 2008 intel Core 2 Duo iMac with only 4G of Ram.  Will I be able to run Lightroom 5 okay if I upgrade from Snow Leopard to Lion?  What will happen to the applications that aren't 64-bit compatible?  Also the Eye-one Display 2 colorimeter to calibrate the monitor will not run on Lion, so that will be an expensive upgrade to an i1DisplayPro. Is the upgrade important enough to offset the expense?  I have an Epson R2000 printer.  Will there be problems with the drivers if I upgrade to Lion?  It would be great to hear from other mac users who are also photographers and who print their own photos.    

    Before upgrading to Lion be sure to read this link:
    https://discussions.apple.com/docs/DOC-6271
    Adobe lists these requirements:
    http://www.adobe.com/products/photoshop-lightroom/tech-specs.html
    Looking at http://www.everymac.com/ even the earliest 2008 iMac was fully 64 bit, even though Boot Camp doesn't support 64 bit Windows on that machine.

  • SQL Server Express compatibility with Windows 8.1 - Which version(s) are compatible?

    We have purchased a new computer that has Win 8.1 Pro. We are migrating an application from a Win 7 Pro machine we are currently successfully using (the vendor migrates it for us) and they have said that the application will require the installation of SQL
    Server 2008 Express (which we do have on our Win 7 machine).
    In looking at the requirements for SQL Server 2008 Express (on the download page for it), it does not mention it being compatible with Win 8.1  
    In addition, Installation Instructions  says that it requires:
     Microsoft .Net Framework 3.5 SP1
     Windows Installer 4.5.
     Windows PowerShell 1.0
    I see that 3.5 is already listed as a program feature of Win8.1 and I've enabled it. Do I need to install SP1? I downloaded it, and launched it, and nothing happened.
    I also looked at the Windows Installer 4.5 download page, and it's not clear if that is compatible with 8.1. Do I need to download and install it?
    Power Shell 2.0 is already installed. I assume that will be backwards compatible with PowerShell 1.0; is that correct?
    I saw another question about SQL Server Express Compatibility with Win 8.1 (http://social.technet.microsoft.com/Forums/windows/en-US/038ec00e-4fc1-41ba-9fdc-21c022aad67e/action?threadDisplayName=sql-server-express-compatibility-with-windows-81) and the response
    said that SQL Server Express 2012 will work, but the link contained in the answer led to a page for SQL Server Express 2014.  
    My vendor has told me that SQL SERver Express 2012 will be backwards compatible with their product. But they said that I would first have to install 2008 first. Is that correct for Win 8.1?
    So, the ultimate questions are:
    1. What is the link for Sql Server 2012 Express for Win 8.1? 
    2. Will the SQL Server 2012 Express download require prior install of the 2008 version
    3. What other component requirements are required for SQL Server 2012 Express, and how can I determine if they have already been installed. (This is a brand new computer with a clean Win8.1 Install).
    4. Finally, can we use the 2014 version of SQL Server Express for Win 8.1? If so, questions 1, 2 and 3 apply, too.
    Thanks for your help on this!! HIGH ANXIETY. 

    Hello,
    The following article provides which updates are required to make SQL Server versions compatible with Windows 8 or 8.1:
    http://support.microsoft.com/kb/2681562/en-us
    1. You can use the product updates feature on SQL Server 2012 to make it compatible with Window 8.1. Apply SP1 as described on the following
    article:
    http://www.sqlcoffee.com/SQLServer2012_0008.htm
    2. No.
    3. Download and install .NET Framework 4.0 and enable .NET Framework 3.5. For more information:
    http://www.sqlcoffee.com/SQLServer2012_0017.htm
    4. Yes, you can use SQL Server 2014 with Windows 8.1. Please refer to the Support article provided above.
    Hope this helps.
    Regards,
    Alberto Morillo
    SQLCoffee.com

  • Blue Ray Disk drive compatibility with DVD S Pro, Mac Pro

    Ok, I'll make this an official question, where might I find info on BDR drive compatibility with DVD S Pro, Mac Pro, etc? I'm a little surprised that there doesn't seem to be much info available.
    I can always use my Pioneer BDR-202 with a windows box, I have several, but I'm trying to get AWAY from them.
    Any thoughts, links, etc. welcome, thanks
    Les

    Blu-ray offers a level of interacivity that is not possible with DVDs, so it isn't just an different drive that you are getting with Blu-ray. Seeing how Apple didn't upgrade DVD SP with the new FCP Suite 2, it is reasonable to assume they are working on a separate Blu-Ray Studio Pro, that is going to be completely different than DVD SP. Adobe Encore's support for Blu-Ray is extremely buggy, so obviously moving from DVD programming to Blu-Ray programming isn't just a simple tweak to the code.
    Apple doesn't pre-announce software they are working on so this is all guess work, but it is reasonable to assume that they are working on a Blu-Ray programming application. Be patient. Do you really have the money to burn on the bleeding edge of new technology? A single Blu-Ray burnable disc sells for $20. Two months ago the exact same disc sold for $45. Prices will continue to fall as things stablize.

Maybe you are looking for