Question on SNMP Read-Write String ...

Hi,
My question is that if I am using an SNMP read-write community string on the device, would Prime LMS still require
the logging credentials of the device via ie) telnet/ssh ?
The reason how I undertand this as long as the SNMP manager (Prime LMS) and the agent (end device) have the same read-write community,
couldn't the Prime LMS just write to the device without the standard logging credentials ? or is the logging credential of the device is a must for it
to push configuration to the device ?
Pls advise.
Many thanks.
Cheers,
- sn -

Even though the SNMP communication is there between device and LMS, it is not possible to configure any device using SNMP, except for the RW variable and OIDs, which are limited in their scope.
It is not possible to configure, but to copy configuration to or from device using SNMP. See the following document to check further:
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_configuration_example09186a0080094aa6.shtml
Many people use this manual process to copy configuration from device using SNMP, edit it and copy back to device to make configuration changes, but ideally no NMS server does it and LMS is no exception.
It uses transport Layer protocols like telnet/ssh to communicate with device like a normal user to configure commands, which in this case is done by Netconfig job.
For more details see :
http://www.cisco.com/en/US/products/sw/cscowork/ps2073/products_tech_note09186a00800a6974.shtml
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.3/user/guide/netcfg.html#wp1070214
-Thanks
Vinod Arya

Similar Messages

Using Bridgeview with the IAK/IAS Server, I was able to read and write several registers using a string tag. In DSC using the Lookout Protocal Driver, I do not see a way to read/write string tags.

In the tag configuration I can select for a string tag, but I do not see a way to set up the Lookout Protocal Driver for a string tag.

That's right - The old IAK/IAS Servers from National Instruments were a tighten developement with BridgeVIEW together - so that they implement the string data type. Since NI recommends to use the LPD drivers instead of the IAK Servers there is no way to configure string tags in the Lookout protocol drivers. The LPDs or Lookout does not really handle arrays/strings at all - that's a limitation for the Lookout protocol drivers.
Roland

Read/Write 2d numeric array or string array into bin file

Can anyone pls help me to resolve this problem
Attachments:
bin file.vi ‏9 KB

You are still using the wrong format.
Whatever you are doing has nothing to do with a binary file.
You are still using way too much duplicate code.
All you probably need is read/write from spreadsheet file, no need to reinvent the wheel.
Your code will fail if the numbers contain decimal digits (since your array is DBL, it could! If your array only contains integers, you are using the wrong numeric representation).
You string code will fail if the array elements contains tabs, for example.
You still don't need a sequence structure.
LabVIEW Champion . Do more with less code and in less time .

Write string (7 chars), int16, sgl into binary file and read it in C

How to write write string (7 chars), int16, sgl, string (5 chars) into binary file and then read it in C ?
Total 18 Bytes file (binary) should be created.

Hi,
this could be done that way:
You have to make sure the strings have their correct length!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Read/write a string in a socket

hi everyone!
I d like to write and read a String such as ("YOU WON: MAGIC NUMBER IS"+ num); through a socket.
Can i use a method of DataInputStream-DataOutputStream or i have to use a method of other class?
thanks

cotton.m wrote:
jverd wrote:
If you want to send a String across a socket, you could either use DataOutputStream.writeObject(yourString), or you could use wrap a BufferedWriter or PrintWriter around the socket's OutputStream Something to note.
ejp is anti-printwriters-attached-to-sockets with the reason being that they swallow exceptions which is not a good idea in networking programming in general.
And I think this is a good point.I hand't thought of that. I agree in general, but would say it should be evaluated for appropriateness on a case-by-case basis.

DVD read/writer Question

I'm so sorry if this has been asked, but here I go anyways. I got my iBook G4 as a gift a bit over a year ago, therefore I didn't really have any control over certain situations. My CD drive does not allow me to burn [write] DVDs. I know this is because it was bought without that feature. Is there anyway to send my iBook to Apple and have them replace my drive with a DVD read/writer? How expensive would this be? Would it just be cheaper to buy and external one from LaCie? Thank you so much for any info!

No doubt it would be cheaper to add an External like a Lacie or one from any number of manufactures
You can if you choose have a new CD/DVD Drive and burner installed and there are several different vendors that will do this for you or you can do it your self.
http://www.mcetech.com/?gclid=CPzAh92mg4YCFQqQJAod-kVOhw
Here is one, but there are literaly hundreds of places that do this.
Don

Read/write drive speed question

I've been watching the read/write speeds in Activity Monitor while I've been transfering about 250 gigs from an internal drive to an external FW 800 Weibetech Drivedock. I notice that if I plug in any other FW drive at all, even another FW800 to the back of the drivedock, the transfer speeds suddenly drop from about 43mb to about 19 or 20mb. Also happens when I plug in to the front of the Mac Pro.
Why is this... can those speeds only be achieved when one drive is plugged into the computer? How can I have more drives plugged in but maintain the fast transfer speeds?
thanks

If my schematic reading-ability isn't too off, USB is the same bridge, same controller, different bus(es):
http://developer.apple.com/documentation/HardwareDrivers/Conceptual/MacPro_0608/Articles/M43_0906arch.html

Hard drive read/write question

Hi,
I purchased this mac pro(2008) with the stock seagate 320gb hard drive (model ST3320820AS_P) and I am interested to know what kind of read write numbers to expect from this drive.
I am having a tough time trying to find any numbers that aren't in reference to RAID setups, and became concerned that this drive might be working at peak performance due to firmware issues others are talking about.
(tangent - I would like to add more drives, but am on the fence for WD or seagate)
System Info
Xbench Version 1.3
System Version 10.5.2 (9C31)
Physical RAM 2048 MB
Model MacPro3,1
Drive Type ST3320820AS_P
Sequential 92.82
Uncached Write 70.70 43.41 MB/sec [4K blocks]
Uncached Write 110.35 62.43 MB/sec [256K blocks]
Uncached Read 82.04 24.01 MB/sec [4K blocks]
Uncached Read 129.89 65.28 MB/sec [256K blocks]
Random 33.16
Uncached Write 11.33 1.20 MB/sec [4K blocks]
Uncached Write 73.50 23.53 MB/sec [256K blocks]
Uncached Read 88.77 0.63 MB/sec [4K blocks]
Uncached Read 134.04 24.87 MB/sec [256K blocks]

http://www.barefeats.com/hard94.html
http://www.barefeats.com/quad07.html
http://www.barefeats.com/quad08.html
750GB WD SE16 $168 is hard to beat.
I saw some systems came with WD 320GB. Guess Apple is using both for now.

Dumb question....presentation layer "read / write" permission

Hi, I'm curious to understand what exactly happens when you grant users "read / write" permissions on presentation layer objects? "Read" is self-explanatory...but what exactly does the "write" allow them to do?
Thanks!
Scott

Hi Scott,
Yeah agree with you. Deepika's answers makes more scense.
By any chance have you looked/try at my answer for the post
11g Help please - action links don't update when target reports move

Help in reading writing string type arraya onto socket..???

hi everybody
how i can write and read a string type array on a socket???
plz help
thanks in advance

I see that you have posted this similar Q before [1]. It is already answered. Read and interpret the given answers. Ask new and specific questions if you don't understand the answers and you will be helped. But don't be ignorant and don't doublepost this question in irrelevant forums.
[1] http://forum.java.sun.com/thread.jspa?threadID=5229301

Different read/write VI's

Hello,
I notice that in labview, I can:
read/write to a SPREADSHEET
This requires FILE_PATH and FORMAT
read/write to a FILE
This requires a FILE_PATH and NO format
(because it is binary data)
I can read lines... BUT I CANNOT write lines
First question: why can I not write lines?
Continuing... there are other ways to read/write.
I can OPEN a file
And, then I can read/write
So: how is THIS read/write different from the ones above.
I can see that THIS read/write requires a refnum from the
open... OK... one structural difference...
This one does not allow for formatting... but yields a BROWN data.
Now, what is this DATA... is it binary?
What is the purpose of the OPEN/read/write/Close
on the second lines of the FIL
E/IO vi's
Can someone describe these and how they relate to each other?
Thanks,
Tom
Hello,

Tom Impelluso wrote:
> Hello,
>
> I notice that in labview, I can:
>
> read/write to a SPREADSHEET
> This requires FILE_PATH and FORMAT
>
This is called a TAB delimited file that most spreadsheet applications
can read
there is a TAB between columns and and EOL between rows. Writes in ASCII
(I should say ASCII printable since all chars are ASCII)
>
> read/write to a FILE
> This requires a FILE_PATH and NO format
> (because it is binary data)
Yep
>
>
> I can read lines... BUT I CANNOT write lines
>
> First question: why can I not write lines?
>
I found this strange also but, you can use the Write Char or generate
your own VI from
the lower level VIS. Which would be using the Write Char and adding EOL
as the last character in the line
There is a VI called Write + (String) that does not show up in the
palette but is used in some of the other VIs.
>
> Continuing... there are other ways to read/write.
>
> I can OPEN a file
>
> And, then I can read/write
>
> So: how is THIS read/write different from the ones above.
It is a byte stream which could be almost anything from ASCII to G
datatypes
>
>
> I can see that THIS read/write requires a refnum from the
> open... OK... one structural difference...
> This one does not allow for formatting... but yields a BROWN data.
>
> Now, what is this DATA... is it binary?
Not always but it can be. If you open an Excel file in a text editor you
will see
what a complex byte stream file looks like. The data is interspersed
with formatting bytes.
>
>
> What is the purpose of the OPEN/read/write/Close
> on the second lines of the FILE/IO vi's
these are the primitives that are used in all of the other file
functions.
This is the most basic level of what file I/O does.
>
>
> Can someone describe these and how they relate to each other?
The Open/Read/Write/Close are the primitves. The others are built up
from these
for special file types (like spreadsheet). They use the primitives and
add some formatting
and other options.
Dont reply to this e-mail address. My account is down and I am using
someone elses.
Kevin Kent

Windows Server 2012 - Hyper-V - iSCSI SAN - All Hyper-V Guests stops responding and extensive disk read/write

We have a problem with one of our deployments of Windows Server 2012 Hyper-V with a 2 node cluster connected to a iSCSI SAN.
Our setup:
Hosts - Both run Windows Server 2012 Standard and are clustered.
HP ProLiant G7, 24 GB RAM, 2 teamed NIC dedicated to Virtual Machines and Management, 2 teamed NIC dedicated to iSCSI storage. - This is the primary host and normaly all VMs run on this host.
HP ProLiant G5, 20 GB RAM, 1 NIC dedicated to Virtual Machines and Management, 2 teamed NIC dedicated to iSCSI storage. - This is the secondary host that and is intended to be used in case of failure of the primary host.
We have no antivirus on the hosts and the scheduled ShadowCopy (previous version of files) is switched of.
iSCSI SAN:
QNAP NAS TS-869 Pro, 8 INTEL SSDSA2CW160G3 160 GB i a RAID 5 with a Host Spare. 2 Teamed NIC.
Switch:
DLINK DGS-1210-16 - Both the network cards of the Hosts that are dedicated to the Storage and the Storage itself are connected to the same switch and nothing else is connected to this switch.
Virtual Machines:
3 Windows Server 2012 Standard - 1 DC, 1 FileServer, 1 Application Server.
1 Windows Server 2008 Standard Exchange Server.
All VMs are using dynamic disks (as recommended by Microsoft).
Updates
We have applied the most resent updates to the Hosts, WMs and iSCSI SAN about 3 weeks ago with no change in our problem and we continually update the setup.
Normal operation
Normally this setup works just fine and we see no real difference in speed in startup, file copy and processing speed in LoB applications of this setup compared to a single host with 2 10000 RPM Disks. Normal network speed is 10-200 Mbit, but occasionally
we see speeds up to 400 Mbit/s of combined read/write for instance during file repair
Our Problem
Our problem is that for some reason all of the VMs stops responding or responds very slowly and you can for instance not send CTRL-ALT-DEL to a VM in the Hyper-V console, or for instance start task manager when already logged in.
Symptoms (i.e. this happens, or does not happen, at the same time)
I we look at resource monitor on the host then we see that there is often an extensive read from a VHDX of one of the VMs (40-60 Mbyte/s) and a combined write speed to many files in \HarddiskVolume5\System Volume Information\{<someguid and no file extension>}.
See iamge below.
The combined network speed to the iSCSI SAN is about 500-600 Mbit/s.
When this happens it is usually during and after a VSS ShadowCopy backup, but has also happens during hours where no backup should be running (i.e. during daytime when the backup has finished hours ago according to the log files). There is however
not that extensive writes to the backup file that is created on an external hard drive and this does not seem to happen during all backups (we have manually checked a few times, but it is hard to say since this error does not seem leave any traces in event
viewer).
We cannot find any indication that the VMs themself detect any problem and we see no increase of errors (for example storage related errors) in the eventlog inside the VMs.
The QNAP uses about 50% processing Power on all cores.
We see no dropped packets on the switch.
(I have split the image to save horizontal space).
Unable to recreate the problem / find definitive trigger
We have not succeeded in recreating the problem manually by, for instance, running chkdsk or defrag in VM and Hosts, copy and remove large files to VMs, running CPU and Disk intensive operations inside a VM (for instance scan and repair a database file).
Questions
Why does all VMs stop responding and why is there such intensive Read/Writes to the iSCSI SAN?
Could it be anything in our setup that cannot handle all the read/write requests? For instance the iSCSI SAN, the hosts, etc?
What can we do about this? Should we use MultiPath IO instead of NIC teaming to the SAN, limit bandwith to the SAN, etc?

Hi,
> All VMs are using dynamic disks (as recommended by Microsoft).
If this is a testing environment, it’s okay, but if this a production environment, it’s not recommended. Fixed VHDs are recommended for production instead of dynamically expanding or differencing VHDs.
Hyper-V: Dynamic virtual hard disks are not recommended for virtual machines that run server workloads in a production environment
http://technet.microsoft.com/en-us/library/ee941151(v=WS.10).aspx
> This is the primary host and normaly all VMs run on this host.
According to your posting, we know that you have Cluster Shared Volumes in the Hyper-V cluster, but why not distribute your VMs into two Hyper-V hosts.
Use Cluster Shared Volumes in a Windows Server 2012 Failover Cluster
http://technet.microsoft.com/en-us/library/jj612868.aspx
> 2 teamed NIC dedicated to iSCSI storage.
Use Microsoft MultiPath IO (MPIO) to manage multiple paths to iSCSI storage. Microsoft does not support teaming on network adapters that are used to connect to iSCSI-based storage devices. (At least it’s not supported until Windows Server 2008 R2. Although
Windows Server 2012 has built-in network teaming feature, I don’t article which declare that Windows Server 2012 network teaming support iSCSI connection)
Understanding Requirements for Failover Clusters
http://technet.microsoft.com/en-us/library/cc771404.aspx
> I have seen using MPIO suggests using different subnets, is this a requirement for using MPIO
> or is this just a way to make sure that you do not run out of IP adressess?
What I found is: if it is possible, isolate the iSCSI and data networks that reside on the same switch infrastructure through the use of VLANs and separate subnets. Redundant network paths from the server to the storage system via MPIO will maximize availability
and performance. Of course you can set these two NICs in separate subnets, but I don’t think it is necessary.
> Why should it be better to not have dedicated wireing for iSCSI and Management?
It is recommended that the iSCSI SAN network be separated (logically or physically) from the data network workloads. This ‘best practice’ network configuration optimizes performance and reliability.
Check that and modify cluster configuration, monitor it and give us feedback for further troubleshooting.
For more information please refer to following MS articles:
Volume Shadow Copy Service
http://technet.microsoft.com/en-us/library/ee923636(WS.10).aspx
Support for Multipath I/O (MPIO)
http://technet.microsoft.com/en-us/library/cc770294.aspx
Deployments and Tests in an iSCSI SAN
http://technet.microsoft.com/en-US/library/bb649502(v=SQL.90).aspx
Hope this helps!
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Lawrence
TechNet Community Support

How to read, write and save a file?

Hello everybody,
I have a question about reading , writing and save something into a file (etc text file)
For example: I want to create a file of football in which there are many key words as: "football", "touch down", "quarterback", "ball", "linebacker", "coach", "player"...
Now i want to open to read, write one more word "head" ( synonym with "coach") and store it for using next time. How could i do that?
Could anybody help me about that?
Thank you very much in advance.
still_learn

take a look in the API about FileInputStream and FileOutputStream

Sharing Mac iTunes library with Windows PC (I want to be able to read/write)

Greetings from a new Mac user. I recently purchased a 27" iMAC running OS X 10.7.3. This iMac is now connected to my home network/workgroup.
- I want to build a new iTunes Library on my 1TB internal Mac HD.
- I want my 3 non Mac Machines (1 XP Prof and 2 Windows 7 Home) to be able to view the contents of my new (not yet built) iTunes Library resident on my iMac and of course be able to
- play that content.
- have play counts from my Windows-based be saved back to my iTunes Library.
- be able to rate a song from any computer (Mac or Windows) within this iTunes Library and have that rating saved back to this iTunes Library.
I don't want to have to rely on iTunes "Shared Library" function. In other words I want all PCs to be able to read/write to the same iTunes Library file.
Before I purchased my iMac, my iTunes Library existed on one of my Windows-file system external drives. The pre-requisites for allowing multiple Windows PCs to access/share/write to the same iTunes Library was to:
- share the Windows folder on the external drive in which the iTunes Library file was stored (allowing network users to be able to change the files), and
- make sure all Windows-based PCs ran the same iTunes software version.
Assume: I don't want to change the version of Windows iTunes software from the currently installed 10.5.0 version.
Question 1: Can my Windows PCs access and utilize the same iTunes library file that I plan to build on my iMac hard drive?
Question 2: What older version of Mac iTunes software should I install on my iMac in order to allow the Windows PCs to access and use the iMacs iTunes library file?
Any help would be appreciated. Thanks.

Hmmm... thanks for the reply. This of course, yields another question. When you say 'you could format to FAT32 which both can use'; do you mean format the iTunes Hard drive on which my iTunes music now resides? If so, this would mean I would need to copy the music off the internal iMac hard drive, then format the drive to FAT32, then copy the music back.
Is this what you meant?

Error 33172 occurred at Read & Write data transfer between two or more PF2010 controller

Hi,i need to do data transfer between two or more FP2010 controller.e.g. FP2010(A) & FP2010(B).
FP2010(A) need to transfer the measurement (from its I/O module) to FP2010(B) to do the data analysis.These data transfer should be synchronous btw two controller to prevent data lost.
From the vi used in the attachment,i encountered some problems at:
(1) Error 33172 occurred while publishing the data.Can i create and publish data under different item name?
(2) How to synchronies the read & write btw contorller?
All controller are communicating with each other directly without the need of a host computer to link them together
Is there any other method to do fast data transfer betwe
en controller?

Hi YongNei,
You were succesful in omiting enough information to make it very difficult to answer!
Please post your example.
Please tell us what version of LV-RT you are using.
Please define what you concider "fast data transfer".
Have you concidered mapping the FP tags of FP2010(A) to FP2010(B) and vise versa?
WHat exactly has to be syncronized?
If you have something that is close to working, share that.
Well, that as far as I can go with the info you have provided. Depending on the details, what you are asking could be anything from trivial to impossible with the currently available technology. I just can't say.
It would probably be a good idea to start over with a fresh question (sorry) because not many people are going to know what a a "
PF2010" is and I can not guarentee that I will be able to get back to you personally until next week-end.
Trying to help you get an answer,
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Question on SNMP Read-Write String ...

Similar Messages

Maybe you are looking for