R12 Database not starting

hi ,
when im trying to start the database in R12 instance im getting the following error...
im using redhat limux server version 4.0....
ORA-00600: internal error code, arguments: [2252], [2249], [688368325], [], [],
how can i solve this.??..
thanks,
vasanth.

Hi,
Please check the db alert log file, you will get more information about the cause.
Check the below forum discussion also
Re: R12 Install always fails with ORA-00600: internal error code, arguments:
Thanks,
Ajikumar G
Expertise in Oracle Apps...

Similar Messages

  • Oracle Database Not Starting Up Properly

    On VMware there's a known issue with Oracle databases on a Windows client not starting up properly all the time and a manual startup using oradim -start -sid <whatever> is required to get it fully running. I kinda figured that I wouldn't run into the exact same issue on Oracle VM. I created a brand new Oracle VM Windows 2003 32-bit server, installed the Oracle drivers for paravirtualization, and whammo, the problem is still here. I didn't find anything in this forum about the database not starting up, so I'm wondering if others are running into the same problem and how to resolve the issue. Thanks a bunch for your help.

    keithrust wrote:
    On VMware there's a known issue with Oracle databases on a Windows client not starting up properly all the time and a manual startup using oradim -start -sid <whatever> is required to get it fully running. Hmmm, doing it several time, and never seen such issue. Which "known issue" and by who are you talking about ?
    I created a brand new Oracle VM Windows 2003 32-bit server, installed the Oracle drivers for paravirtualization, and whammo, the problem is still hereI'm sure, you miss something somewhere in the config. Right now, you're on supported configuration, you could either raise a SR to the support, or get help from your peer on Oracle Database General forum.
    Ah, but it's not a Windows issue. On a non-VM Windows box the database starts just fine all the time. Again, this is a known issue acknowledged by Oracle on the VMware side, I'm just surprised it exists on the Oracle VM side.Again, give more details about this "known issue". Never heard about that, eventhough I've been around for years.
    I was afraid you were going to ask that. I'll have to search for it again, but I think you can do the same as well....Well, I doubt you could find a Metalink note about Oracle on VMWare. So far, Oracle has always refused to support database on OS virtualized on VMWare (or any VM software other than Oracle VM). Based on that, you could be sure, your "known issue" is not an issue on Oracle VM.
    If you want more help, again, give more details about your issue.
    Nicolas.

  • Connected to auxiliary database (not started)

    Hello! I'm establishing Data Guard on Oracle 11g (x64). OS - CentOS 6.6 x86_x64.
    The problem occurs when i'm trying to connect from my primary db to standby.
    I expect:
    connected to auxiliary database (not mounted)
    but getting
    not started
    And when i'm trying to:
    duplicate target database for standby nofilenamecheck dorecover;
    I get an expected error:
    Starting Duplicate Db at 17-MAR-15
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    RMAN-03002: failure of Duplicate Db command at 03/17/2015 01:04:49
    RMAN-06403: could not obtain a fully authorized session
    RMAN-04006: error from auxiliary database: ORA-01034: ORACLE not available
    ORA-27101: shared memory realm does not exist
    Linux-x86_64 Error: 2: No such file or directory
    I also read simular topic:
    Creating a duplicated database from active database
    but i check several times my listener.ora on standby, and i can't figure out where the problem lies.
    Actions that preceded the appearance of the error:
    The main base is loaded by default (startup)
    StandBy base loaded without mount (startup nomount)
    On the main launch from the terminal «rman target /»
    Command «connect auxiliary sys@orclstandby»
    Password (sys)
    Got: connected to auxiliary database (not started)
    Here is my configuration files:
    Primary:
    tnsname:
    orclprimary =
      (DESCRIPTION =
       (ADDRESS = (PROTOCOL = TCP)(HOST = oracle11centos.com)(PORT = 1521))
       (CONNECT_DATA =
       (SERVER = DEDICATED)
       (SERVICE_NAME = orcl.com)
    orclstandby =
      (DESCRIPTION =
       (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.1.115)(PORT = 1521))
       (CONNECT_DATA =
       (SERVER = DEDICATED)
       (SERVICE_NAME = orclstandby.com)
       (SID_NAME = orcl)
      pfileORCL.ora
    orcl.__db_cache_size=301989888
    orcl.__java_pool_size=4194304
    orcl.__large_pool_size=4194304
    orcl.__oracle_base='/u01/app/oracle'#ORACLE_BASE set from environment
    orcl.__pga_aggregate_target=314572800
    orcl.__sga_target=469762048
    orcl.__shared_io_pool_size=0
    orcl.__shared_pool_size=150994944
    orcl.__streams_pool_size=0
    *.audit_file_dest='/u01/app/oracle/admin/orcl/adump'
    *.audit_trail='db'
    *.compatible='11.2.0.0.0'
    *.control_files='/u01/app/oracle/oradata/orcl/control01.ctl','/u01/app/oracle/flash_recovery_area/orcl/control02.ctl'
    *.db_block_size=8192
    *.db_domain='com'
    *.db_name='orcl'
    *.db_recovery_file_dest='/u01/app/oracle/flash_recovery_area'
    *.db_recovery_file_dest_size=4070572032
    *.diagnostic_dest='/u01/app/oracle'
    *.dispatchers='(PROTOCOL=TCP) (SERVICE=orclXDB)'
    *.memory_target=784334848
    *.open_cursors=300
    *.processes=150
    *.remote_login_passwordfile='EXCLUSIVE'
    *.undo_tablespace='UNDOTBS1'
    db_unique_name='orclprimary'
    log_archive_config='dg_config=(orclprimary,orclstandby)'
    log_archive_dest_1='SERVICE=orclstandby LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES,PRIMARY_ROLE) db_unique_name=orclstandby'
    log_archive_dest_2='LOCATION=/u01/app/oracle/oradata/orcl/archive VALID_FOR=(ALL_LOGFILES,ALL_ROLES) db_unique_name=orclprimary'
    log_archive_dest_state_1=ENABLE
    log_archive_dest_state_2=ENABLE
    fal_client='orclprimary'
    fal_server='orclstandby'
    standby_file_management='AUTO'
    StandBy
    tnsname
    orclstandby =
      (DESCRIPTION =
       (ADDRESS = (PROTOCOL = TCP)(HOST = oracle11standby2centos.com)(PORT = 1521))
       (CONNECT_DATA =
       (SERVER = DEDICATED)
    (SERVICE_NAME = orclstandby.com)
    orclprimary =
      (DESCRIPTION =
       (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.1.101)(PORT = 1521))
       (CONNECT_DATA =
       (SERVER = DEDICATED)
    (SERVICE_NAME = orcl.com)
    listener
    SID_LIST_LISTENER =
    (SID_LIST =
      (SID_DESC =
       (GLOBAL_DBNAME = orclstandby.com)
      (ORACLE_HOME = /u01/app/oracle/product/11.2.0/dbhome_1/)
    (SID_NAME = orcl)
    LISTENER =
    (DESCRIPTION_LIST =
       (DESCRIPTION =
       (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
       (ADDRESS = (PROTOCOL = TCP)(HOST = oracle11standby2centos.com)(PORT = 1521))
    ADR_BASE_LISTENER = /u01/app/oracle
    pfileORCL.ora
    orcl.__db_cache_size=301989888
    orcl.__java_pool_size=4194304
    orcl.__large_pool_size=4194304
    orcl.__oracle_base='/u01/app/oracle'#ORACLE_BASE set from environment
    orcl.__pga_aggregate_target=314572800
    orcl.__sga_target=469762048
    orcl.__shared_io_pool_size=0
    orcl.__shared_pool_size=150994944
    orcl.__streams_pool_size=0
    *.audit_file_dest='/u01/app/oracle/admin/orcl/adump'
    *.audit_trail='db'
    *.compatible='11.2.0.0.0'
    *.control_files='/u01/app/oracle/oradata/orcl/control01.ctl','/u01/app/oracle/flash_recovery_area/orcl/control02.ctl'
    *.db_block_size=8192
    *.db_domain='com'
    *.db_name='orcl'
    *.db_recovery_file_dest='/u01/app/oracle/flash_recovery_area'
    *.db_recovery_file_dest_size=4070572032
    *.diagnostic_dest='/u01/app/oracle'
    *.dispatchers='(PROTOCOL=TCP) (SERVICE=orclXDB)'
    *.memory_target=784334848
    *.open_cursors=300
    *.processes=150
    *.remote_login_passwordfile='EXCLUSIVE'
    *.undo_tablespace='UNDOTBS1'
    db_unique_name='orclstandby'
    log_archive_config='dg_config=(orclprimary,orclstandby)'
    log_archive_dest_1='SERVICE=orclstandby LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES,PRIMARY_ROLE) db_unique_name=orclprimary'
    log_archive_dest_2='LOCATION=/u01/app/oracle/oradata/orcl/archive VALID_FOR=(ALL_LOGFILES,ALL_ROLES) db_unique_name=orclstandby'
    log_archive_dest_state_1=ENABLE
    log_archive_dest_state_2=ENABLE
    fal_client='orclstandby'
    fal_server='orclprimary'
    standby_file_management='AUTO'
    Where I did wrong?

    Thanks for the quick reply!
    Primary:
    sqlplus sys/<password>@orclstandby as sysdba
    Result:
    SQL*Plus: Release 11.2.0.1.0 Production on Tue Mar 17 09:01:29 2015
    Copyright (c) 1982, 2009, Oracle.  All rights reserved.
    Connected to an idle instance.
    SQL>
    sqlplus sys/<password>@orclprimary as sysdba
    Result:
    SQL*Plus: Release 11.2.0.1.0 Production on Tue Mar 17 09:28:21 2015
    Copyright (c) 1982, 2009, Oracle.  All rights reserved.
    ERROR:
    ORA-12514: TNS:listener does not currently know of service requested in connect
    descriptor
    Standby
    sqlplus sys/<password>@orclstandby as sysdba
    Result:
    SQL*Plus: Release 11.2.0.1.0 Production on Tue Mar 17 09:08:37 2015
    Copyright (c) 1982, 2009, Oracle.  All rights reserved.
    Connected to an idle instance.
    SQL>
    sqlplus sys/<password>@orclprimary as sysdba
    Result:
    SQL*Plus: Release 11.2.0.1.0 Production on Tue Mar 17 09:10:22 2015
    Copyright (c) 1982, 2009, Oracle.  All rights reserved.
    ERROR:
    ORA-12514: TNS:listener does not currently know of service requested in connect
    descriptor

  • RMAN saying database not started??

    Hi there,
    If I log into my database through OEM, it connects fine.
    Through Unix, I set my SID and type in:
    rman target /
    It connects me to rman but says: connected to target database (not started)
    I then try and run a crosscheck archivelog all and it says this:
    Erro message stack....
    failure of crosscheck command
    automatic channel allocation initialization failed
    could not obtain a fully authorized session
    ORACLE not available
    shared memory realm does not exist
    Linux Error: No such file or directory.
    Any thoughta on what is going on here?
    Thanks in advance!

    herb:oradbp2 ~$ id
    uid=500(herb) gid=501(dba) groups=501(dba)
    herb:oradbp2 ~$ env | sort
    _=/bin/env
    DISPLAY=oradbp2.lilydale:33
    G_BROKEN_FILENAMES=1
    HISTSIZE=1000
    HOME=/home/herb
    HOSTNAME=oradbp2.lilydale
    INPUTRC=/etc/inputrc
    KDEDIR=/usr
    LANG=en_US
    LD_ASSUME_KERNEL=2.4.19
    LD_LIBRARY_PATH=:/d01/app/oracle/9ise/lib
    LESSOPEN=|/usr/bin/lesspipe.sh %s
    LOGNAME=herb
    LS_COLORS=no=00:fi=00:di=00;33:ln=00;36:pi=40;33:so=00;35:bd=40;33;01:cd=40;33;01:or=01;05;37;41:mi=01;05;37;41:ex=00;32:*.cmd=00;32:*.exe=00;32:*.com=00;32:*.btm=00;32:*.bat=00;32:*.sh=00;32:*.csh=00;32:*.tar=00;31:*.tgz=00;31:*.arj=00;31:*.taz=00;31:*.lzh=00;31:*.zip=00;31:*.z=00;31:*.Z=00;31:*.gz=00;31:*.bz2=00;31:*.bz=00;31:*.tz=00;31:*.rpm=00;31:*.cpio=00;31:*.jpg=00;35:*.gif=00;35:*.bmp=00;35:*.xbm=00;35:*.xpm=00;35:*.png=00;35:*.tif=00;35:
    MAIL=/var/spool/mail/herb
    ORACLE_BASE=/d01/app/oracle
    ORACLE_HOME=/d01/app/oracle/9ise
    ORACLE_SID=LSDB
    PATH=/d01/app/oracle/9ise/bin:/d01/app/oracle/9ise/OPatch:/usr/kerberos/bin:/usr/local/bin:/bin:/usr/bin:/usr/X11R6/bin:/home/herb/bin
    PWD=/home/herb
    SHELL=/bin/bash
    SHLVL=1
    SSH_ASKPASS=/usr/libexec/openssh/gnome-ssh-askpass
    SSH_CLIENT=::ffff:10.1.6.200 50766 22
    SSH_CONNECTION=::ffff:10.1.6.200 50766 ::ffff:10.1.0.193 22
    SSH_TTY=/dev/pts/1
    TERM=xterm
    USER=herb
    herb:oradbp2 ~$ ps -ef | grep -i pmon
    herb 1934 1 0 2010 ? 00:02:32 ora_pmon_lsdb
    herb 3984 3359 0 11:06 pts/1 00:00:00 grep -i pmon
    herb:oradbp2 ~$ ls -l $ORACLE_HOME/dbs
    total 18960
    lrwxrwxrwx 1 herb dba 53 Dec 4 2008 initanalyzer.ora -> /d01/app/oracle/admin/analyzer/pfile/initanalyzer.ora
    lrwxrwxrwx 1 herb dba 49 Nov 12 2008 initcit1p1.ora -> /d01/app/oracle/admin/cit1p1/pfile/initcit1p1.ora
    lrwxrwxrwx 1 herb dba 45 Oct 25 2008 initlsdb.ora -> /d01/app/oracle/admin/lsdb/pfile/initlsdb.ora
    lrwxrwxrwx 1 herb dba 45 Nov 22 2008 initpvsp.ora -> /d01/app/oracle/admin/pvsp/pfile/initpvsp.ora
    lrwxrwxrwx 1 herb dba 43 Nov 12 2008 initrep.ora -> /d01/app/oracle/admin/rep/pfile/initrep.ora
    -rw-rw---- 1 herb dba 24 Dec 13 2008 lkANALYZER
    -rw-rw---- 1 herb dba 24 Dec 12 2008 lkCIT1P1
    -rw-rw---- 1 herb dba 24 Dec 9 2008 lkKRON43
    -rw-rw---- 1 herb dba 24 May 18 2010 lkLSDB
    -rw-rw---- 1 herb dba 24 Dec 13 2008 lkPVSP
    -rw-rw---- 1 herb dba 24 Dec 12 2008 lkREP
    -rwSr----- 1 herb dba 2048 Dec 4 2008 orapwanalyzer
    -rwSr----- 1 herb dba 2048 Nov 12 2008 orapwcit1p1
    -rwSr----- 1 herb dba 2048 Nov 25 2008 orapwkron43
    -rwSr----- 1 herb dba 1536 Oct 25 2008 orapwlsdb
    -rwSr----- 1 herb dba 2048 Nov 22 2008 orapwpvsp
    -rwSr----- 1 herb dba 2048 Nov 12 2008 orapwrep
    -rw-rw---- 1 herb dba 4718592 Mar 10 2009 p1k9ipga_1_1
    -rw-rw---- 1 herb dba 1630208 Dec 12 2008 snapcf_analyzer.f
    -rw-rw---- 1 herb dba 1630208 Dec 11 2008 snapcf_cit1p1.f
    -rw-rw---- 1 herb dba 1679360 Dec 9 2008 snapcf_kron43.f
    -rw-rw---- 1 herb dba 6397952 Jan 16 18:27 snapcf_lsdb.f
    -rw-rw---- 1 herb dba 1630208 Dec 12 2008 snapcf_pvsp.f
    -rw-rw---- 1 herb dba 1630208 Dec 11 2008 snapcf_rep.f
    -rw-rw---- 1 herb dba 2560 Oct 25 2008 spfilelsdb.ora.bak

  • Oracle database not starting up in oracle 10g RAC

    Hi!
    Recently I came across one problem with one node oracle 10g RAC.When the Oracle database is started,while opening it is giving ORA-03113:End of file on communication channel error.When I saw the the alert trace file and other trace files I found Disk group is exhausted error and it is not able to create .dbf files.Actually it is not a production server and I gave archive log destination in SAN.Even the spfile(content of init_database.ora) is in SAN..
    I tried Asmcmd utility to delete the archive log files.As the oracle is not available I am not able to asmcmd prompt.
    How to change the destination of archive log and to remove the old archive log files(as it is a testing environment we can remove) from SAN?Please let me know.
    Thanks & Regards
    Srikanth MVS

    keithrust wrote:
    On VMware there's a known issue with Oracle databases on a Windows client not starting up properly all the time and a manual startup using oradim -start -sid <whatever> is required to get it fully running. Hmmm, doing it several time, and never seen such issue. Which "known issue" and by who are you talking about ?
    I created a brand new Oracle VM Windows 2003 32-bit server, installed the Oracle drivers for paravirtualization, and whammo, the problem is still hereI'm sure, you miss something somewhere in the config. Right now, you're on supported configuration, you could either raise a SR to the support, or get help from your peer on Oracle Database General forum.
    Ah, but it's not a Windows issue. On a non-VM Windows box the database starts just fine all the time. Again, this is a known issue acknowledged by Oracle on the VMware side, I'm just surprised it exists on the Oracle VM side.Again, give more details about this "known issue". Never heard about that, eventhough I've been around for years.
    I was afraid you were going to ask that. I'll have to search for it again, but I think you can do the same as well....Well, I doubt you could find a Metalink note about Oracle on VMWare. So far, Oracle has always refused to support database on OS virtualized on VMWare (or any VM software other than Oracle VM). Based on that, you could be sure, your "known issue" is not an issue on Oracle VM.
    If you want more help, again, give more details about your issue.
    Nicolas.

  • Oracle 9i database not starting

    Dear all,
    need ur help. i have installed oracle9i on wndows xp. then i stoped all the services for 9i. n i installed oracle 10g also.
    My problem is that bothy database servies are their and they are automatic.
    10 g Database is starting automatically. but 9i database instance is not opeing automatically.
    i tried STARTTYPE the opetion of oradim also but its not working.
    tell me how to start the 9i database automatically.
    regds
    Ashish

    most likely while installation you might have given a different port no.As a result oracle has ultimately landed up with having more than one listener.And some times I have seen after installation the previous listener does not get started.So I would like to you to check your listener.
    One more point while 2nd installtion you might have changed your oracle home.so while trying to connect to prev instance try using sqlplus from previous oracle_home\bin\.

  • Database not starting,REDO log file error?

    My DB was working fine uptill last evening, when i restarted it for some DB task it showed me an error ..
    ORA-00333: redo log read error block 57346 count 8192
    I studied the alert log file & related trace file .... but could not conclude what to do ?? Can any one suggest me what could be the solution...
    ORACLE 10g R2
    Windows 2003 Server
    Database in NOARCHIVELOG mode.
    I don't have the recent backup.The one i have is 20 days old.
    Alert Log file contents : -
    Wed Jun 02 20:22:19 2010
    Aborting crash recovery due to error 333
    Wed Jun 02 20:22:19 2010
    Errors in file e:\oracle\product\10.2.0\admin\ora10g\udump\ora10g_ora_140.trc:
    ORA-00333: redo log read error block 57346 count 8192
    ORA-333 signalled during: ALTER DATABASE OPEN...
    Wed Jun 02 20:37:15 2010
    db_recovery_file_dest_size of 2048 MB is 0.00% used. This is a
    user-specified limit on the amount of space that will be used by this
    database for recovery-related files, and does not reflect the amount of
    space available in the underlying filesystem or ASM diskgroup.
    Wed Jun 02 20:43:53 2010
    Shutting down instance: further logons disabled
    Wed Jun 02 20:43:53 2010
    Stopping background process CJQ0
    Wed Jun 02 20:43:54 2010
    Stopping background process MMNL
    Wed Jun 02 20:43:55 2010
    Stopping background process MMON
    Wed Jun 02 20:43:56 2010
    Shutting down instance (immediate)
    License high water mark = 3
    Wed Jun 02 20:43:56 2010
    Stopping Job queue slave processes
    Wed Jun 02 20:43:56 2010
    Job queue slave processes stopped
    Waiting for dispatcher 'D000' to shutdown
    All dispatchers and shared servers shutdown
    Wed Jun 02 20:43:58 2010
    ALTER DATABASE CLOSE NORMAL
    ORA-1109 signalled during: ALTER DATABASE CLOSE NORMAL...
    Wed Jun 02 20:43:58 2010
    ALTER DATABASE DISMOUNT
    Completed: ALTER DATABASE DISMOUNT
    ARCH: Archival disabled due to shutdown: 1089
    Shutting down archive processes
    Archiving is disabled
    Archive process shutdown avoided: 0 active
    ARCH: Archival disabled due to shutdown: 1089
    Shutting down archive processes
    Archiving is disabled
    Archive process shutdown avoided: 0 active
    Trace file to read ora10g_ora_140.trc:-
    Dump file e:\oracle\product\10.2.0\admin\ora10g\udump\ora10g_ora_140.trc
    Wed Jun 02 20:22:18 2010
    ORACLE V10.2.0.1.0 - Production vsnsta=0
    vsnsql=14 vsnxtr=3
    Oracle Database 10g Enterprise Edition Release 10.2.0.1.0 - Production
    With the Partitioning, OLAP and Data Mining options
    Windows Server 2003 Version V5.2 Service Pack 1
    CPU                 : 2 - type 586, 1 Physical Cores
    Process Affinity    : 0x00000000
    Memory (Avail/Total): Ph:3527M/4094M, Ph+PgF:4386M/5973M, VA:800M/2047M
    Instance name: ora10g
    Redo thread mounted by this instance: 1
    Oracle process number: 15
    Windows thread id: 140, image: ORACLE.EXE (SHAD)
    *** SERVICE NAME:() 2010-06-02 20:22:18.406
    *** SESSION ID:(159.3) 2010-06-02 20:22:18.406
    Successfully allocated 2 recovery slaves
    Using 545 overflow buffers per recovery slave
    Thread 1 checkpoint: logseq 14261, block 2, scn 86974094
      cache-low rba: logseq 14260, block 4023
        on-disk rba: logseq 14262, block 3758, scn 86978396
      start recovery at logseq 14261, block 2, scn 86974094
    ORA-00333: redo log read error block 57346 count 8192
    ORA-00312: online log 2 thread 1: 'E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORA10G\REDO02.LOG'
    ORA-27070: async read/write failed
    OSD-04016: Error queuing an asynchronous I/O request.
    O/S-Error: (OS 2) The system cannot find the file specified.
    ORA-00333: redo log read error block 57346 count 8192
    ORA-00312: online log 2 thread 1: 'E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORA10G\REDO02.LOG'
    ORA-27091: unable to queue I/O
    ORA-27070: async read/write failed
    OSD-04006: ReadFile() failure, unable to read from file
    O/S-Error: (OS 2) The system cannot find the file specified.
    ORA-00333: redo log read error block 57346 count 8192
    *** 2010-06-02 20:43:58.812
    *** 2010-06-02 20:43:58.812 60680 kcrr.c
    ARCH: Archival disabled due to shutdown: 1089
    *** 2010-06-02 20:43:59.812 60680 kcrr.c
    ARCH: Archival disabled due to shutdown: 1089

    Hi,Aman this(following) may is not good way for opening database,but OP can try and open own database:
    @ DBA4 you will see from following example how you can open your database.In your online log files was corrupted,therefore you have to do following step by step then you database will open.
    SQL> alter database clear unarchived logfile group 2;
    alter database clear unarchived logfile group 2
    ERROR at line 1:
    ORA-01624: log 2 needed for crash recovery of instance p (thread 1)
    ORA-00312: online log 2 thread 1:
    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\REDO02.LOG'
    SQL> alter database backup controlfile to trace as 'D:\oracle\product\10.2.0\ora
    data\P\c.txt';
    Database altered.
    SQL> shutdown abort;
    ORACLE instance shut down.
    SQL> startup nomount;
    ORACLE instance started.
    Total System Global Area  125829120 bytes
    Fixed Size                  1288100 bytes
    Variable Size              75499612 bytes
    Database Buffers           41943040 bytes
    Redo Buffers                7098368 bytes
    SQL> CREATE CONTROLFILE REUSE DATABASE "P" RESETLOGS   ARCHIVELOG
      2      MAXLOGFILES 16
      3      MAXLOGMEMBERS 3
      4      MAXDATAFILES 100
      5      MAXINSTANCES 8
      6      MAXLOGHISTORY 292
      7  LOGFILE
      8    GROUP 1 'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\REDO01.LOG'  SIZE 50M,
      9    GROUP 2 'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\REDO02.LOG'  SIZE 50M,
    10    GROUP 3 'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\REDO03.LOG'  SIZE 50M
    11  DATAFILE
    12    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\SYSTEM01.DBF',
    13    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\UNDOTBS01.DBF',
    14    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\SYSAUX01.DBF',
    15    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\USERS01.DBF',
    16    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\TS_TEST.ORA',
    17    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\TEST.ORA',
    18    'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\TEST1.ORA'
    19  CHARACTER SET WE8MSWIN1252;
    Control file created.
    SQL> alter database open resetlogs;
    alter database open resetlogs
    ERROR at line 1:
    ORA-01194: file 1 needs more recovery to be consistent
    ORA-01110: data file 1: 'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\SYSTEM01.DBF'
    SQL> recover database using backup controlfile until cancel;
    ORA-00279: change 2032832 generated at 06/03/2010 12:42:29 needed for thread 1
    ORA-00289: suggestion :
    D:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\P\ARCHIVELOG\2010_06_03\O1_MF_1_87_
    %U_.ARC
    ORA-00280: change 2032832 for thread 1 is in sequence #87
    Specify log: {<RET>=suggested | filename | AUTO | CANCEL}
    cancel
    ORA-01547: warning: RECOVER succeeded but OPEN RESETLOGS would get error below
    ORA-01194: file 1 needs more recovery to be consistent
    ORA-01110: data file 1: 'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\SYSTEM01.DBF'
    ORA-01112: media recovery not started
    then add *_allow_resetlogs_corruption=true* in pfile then startup database with pfile as
    SQL> startup mount pfile=D:\oracle\product\10.2.0\admin\P\pfile\init.ora.pr
    ORACLE instance started.
    Total System Global Area  125829120 bytes
    Fixed Size                  1288100 bytes
    Variable Size              62916700 bytes
    Database Buffers           54525952 bytes
    Redo Buffers                7098368 bytes
    Database mounted.
    SQL> recover;
    ORA-00283: recovery session canceled due to errors
    ORA-01610: recovery using the BACKUP CONTROLFILE option must be done
    SQL> recover database using backup controlfile until cancel;
    ORA-00279: change 2032832 generated at 06/03/2010 12:42:29 needed for thread 1
    ORA-00289: suggestion :
    D:\ORACLE\PRODUCT\10.2.0\FLASH_RECOVERY_AREA\P\ARCHIVELOG\2010_06_03\O1_MF_1_87_
    %U_.ARC
    ORA-00280: change 2032832 for thread 1 is in sequence #87
    Specify log: {<RET>=suggested | filename | AUTO | CANCEL}
    cancel
    ORA-01547: warning: RECOVER succeeded but OPEN RESETLOGS would get error below
    ORA-01194: file 1 needs more recovery to be consistent
    ORA-01110: data file 1: 'D:\ORACLE\PRODUCT\10.2.0\ORADATA\P\SYSTEM01.DBF'
    ORA-01112: media recovery not started
    SQL> alter database open;
    alter database open
    ERROR at line 1:
    ORA-01589: must use RESETLOGS or NORESETLOGS option for database open
    SQL> alter database open resetlogs;
    Database altered.
    SQL>finally remove allowresetlogs_corruption=true parameter from pfile.

  • HELP! users02.dbf file missing, database not starting

    Hello,
    I created a datafile via Enterprise Manager named users02.dbf for the wrong tablespace (SYSAUX instead of USERS); obviously this datafile was empty. When I realized my error I went and deleted the users02.dbf file from my file system and not from Enterprise Manager (I know.. stupid..)
    The problem that I'm having now is that oracle will not start because it's missing this file, here is the error message:
    SQL> SQL> ALTER DATABASE open
    ERROR at line 1:
    ORA-01113: file 5 needs media recovery
    ORA-01110: data file 5:
    '/var/backup2/oracle/product/10.2.0/Db_1/oradata/standard/users02.dbf'
    I do not hav a backup because it was only a test file.
    Which file do I have to modify in order to tell oracle startup NOT to look for users02.dbf ?
    I really appreciate your help.
    David

    Paul, the last command gave me this error:
    alter database open
    ERROR at line 1:
    ORA-01589: must use RESETLOGS or NORESETLOGS option for database open
    Thanks

  • Oracle Database not starting ORA-01034: ORACLE not available and ORA-27101

    Dear Sir,
    today i have restarted the database server (11gR2) after that database service is not starting, the error message is
    ERROR:
    ORA-01034: ORACLE not available
    ORA-27101: shared memory realm does not exist
    Linux-x86_64 Error: 2: No such file or directory
    Process ID: 0
    Session ID: 0 Serial number: 0

    [oracle@bladb ~]$ export $ORACLE_HOME
    -bash: export: `/oracle/product/11.2.0/dbhome_1': not a valid identifier
    [oracle@bladb ~]$ sqlplus sys/manager as sysdba
    SQL*Plus: Release 11.2.0.1.0 Production on Fri May 3 17:46:28 2013
    Copyright (c) 1982, 2009, Oracle. All rights reserved.
    Connected to an idle instance.
    [oracle@bladb ~]$ tail -20 /oracle/product/11.2.0/dbhome_1/startup.log
    SQL> Connected to an idle instance.
    SQL> ORA-00845: MEMORY_TARGET not supported on this system
    SQL> Disconnected
    /oracle/product/11.2.0/dbhome_1/bin/dbstart: Database instance "bladb" warm started.
    /oracle/product/11.2.0/dbhome_1/bin/dbstart: Starting up database "bladb"
    Fri May 3 17:40:24 IST 2013
    SQL*Plus: Release 11.2.0.1.0 Production on Fri May 3 17:40:24 2013
    Copyright (c) 1982, 2009, Oracle. All rights reserved.
    SQL> Connected to an idle instance.
    SQL> ORA-00845: MEMORY_TARGET not supported on this system
    SQL> Disconnected
    /oracle/product/11.2.0/dbhome_1/bin/dbstart: Database instance "bladb" warm started.

  • Database not starting automatically

    OS windows 2000 server
    database 8i
    I have changed sid of database successfully and manually database is opening up but it is not starting up automatically with machine startup.

    While changing SID of database I have deleted the service and recreated it with
    ORADIM utility .
    -startmode a
    I have even edited the service but of no use .database is not starting up .
    As I have mentioned above oracle service has been started successfully and it is running in auto mode.
    One more problem I am facing after change of SID ,I can to database with user sys
    but when I am trying to connect as normal user I am getting error:
    ORA-03113: end-of-file on communication channel

  • VDI 3.0 installation problems - VDI database not starting

    Hi
    I am trying to install VDI 3.0 (released yesterday) on a Sun Fire X2200 server, running Solaris 10u6. The package installation runs just fine, but I can't get VDI configured properly. When running the vdi-config program, I choose to set up a evaluation VDI host, and then everything runs fine until it reaches the "Starting Sun VDI database (MySQL)" point. It hangs there for a couple of minutes, before simply stating "Failed". The configuration program also prints out the following in the end of the run:
    Common Agent Container Configuration
       + Restarting Common Agent Container service...
    Error when trying to start SMF service: [svc:/application/management/common-agent-container-1:default].
    Please check the SMF log file for more information: [/var/svc/log/application-management-common-agent-container-1:default.log].This seems to be because the common-agent-container-1 service depends on vdadb:sql running, which it fails to.
    If I try to start vdadb:sql manually after the configuration (using svcadm clear vdadb:sql), the following is put into the services log, and the service is still in maintenance mode:
    [ Mar 25 15:16:19 Executing start method ("/opt/SUNWvda/lib/vda-db-service start") ]
    Configuration:                                                                     
       MGMT_NODE=[1]; NDBD_NODE=[1]; SQL_NODE=[1]; MULTI_HOST_MODE=[0];                
       NDBD_CONNECTSTRING=[localhost]; NDBD_INITIAL_ARG=[--initial]; NDBD_NODE_ID=[2]; 
    Starting the Sun Virtual Desktop Infrastructure Database service:                  
       - Starting Management Node... OK                                                
       - Starting Data Node...                                                         
         Arguments: [localhost --initial]...                                           
         Error                                                                         
    [ Mar 25 15:21:26 Method "start" exited with status 95 ]I can't seem to get any further debug messages, and I can't find out how to go any further with this, as "Failed" and "Error" seems to be the only error messages I get.
    As far as I can see, the error message is coming from the "waitForNdbdNodeStartup" function on line 296 of /opt/SUNWvda/lib/vda-db-service, but I can't really get any nearer than that.
    Does anybody know how to get further in this regard?
    /Jeppe

    Hi, I have been reading and trying the solutions on this post to no avail ... as this post is still open and it seems like the subject still applies to my problem, I am using this one... the case is:
    I am trying to setup an evaluation for vdi3 using several machines, 1 for the vdi core, 2 for the secondaries and another one as the storage server. the main and one secondary installed and got configured fine, but the second secondary is failing and I dont know why, I just unconfigured and uninstalled it and did reinstalled and reconfigured it again, but something went wrong, I havent
    touched anything except changing the 300 to 16 in the ini file ...
    bash-3.00# /opt/SUNWvda/sbin/vda-config
    Sun Virtual Desktop Infrastructure 3.0 Configuration
    An Evaluation Sun VDI Host configures all necessary components on one server.
    1 Primary Sun VDI Host
    2 Secondary Sun VDI Host
    0 Evaluation Sun VDI Host
    Select (1/2/0): 2
    Specify the maximum number of concurrent sessions this host will support [100]: 20
    There are as many local users created as the maximum number of concurrent sessions defined.
    Enter the user ID range start [150000]: 20000
    Enter the DNS name of the primary host: holanda
    Enter the DNS name of this host [ghana]:
    You can use the MySQL database of the Sun VDI cluster or connect to a remote MySQL database.
    1 Sun VDI cluster database
    2 Remote database
    Select ([1]/2):
    Do you want to apply the settings? ([y]/n)
    Sun Ray Server Software Configuration
    + Providing configuration data...
    + Loading Sun Ray data store...
    + Populating Sun Ray data store...
    + Creating Sun Ray core services configuration...
    + Restarting Sun Ray data store daemon...
    + Configuring Sun Ray Server Software Web Administration...
    + Adding 20 user accounts for Sun Ray sessions...
    Sun Ray Client Configuration
    + Enabling Kiosk Mode Policy for All Card and Non-Card Users...
    + Enabling LAN Connections...
    + Configuring Sun Ray Connector for Windows Operating Systems...
    + Restarting Sun Ray Server Software...
    MySQL Database Configuration
    + Creating MySQL group (vdadb)...
    + Creating MySQL user (vdadb)...
    + Setting up MySQL directory...
    + Setting up MySQL cluster directory...
    + Initializing database...
    + Starting Sun VDI database (MySQL)...
    Failed.
    + Synchronizing time...
    Sun VDI Web Administration Configuration
    + Enabling Sun VDI web administration...
    + Restarting Sun VDI web administration...
    RDP Broker Configuration
    + Starting RDP broker...
    Common Agent Container Configuration
    + Restarting Common Agent Container service...
    Error when trying to start SMF service: [svc:/application/management/common-agent-container-1:default].
    Please check the SMF log file for more information: [var/svc/log/application-management-common-agent-container-1:default.log].
    The configuration of Sun VDI 3.0 has completed.
    A log file is available at '/var/adm/log/vda-config.2009_04_13_09:00:44.log'.
    The command line tools are located at '/opt/SUNWvda/sbin'.
    You can access the Sun VDI web administration at http://ghana:1800
    the log shows:
    bash-3.00# tail -30 /var/svc/log/application-database-vdadb:core.log
    Configuration:
    MGMT_NODE=[0]; NDBD_NODE=[1]; SQL_NODE=[0]; MULTI_HOST_MODE=[1];
    NDBD_CONNECTSTRING=[holanda]; NDBD_INITIAL_ARG=[--initial]; NDBD_NODE_ID=[2];
    Starting the Sun Virtual Desktop Infrastructure Database service:
    - Starting Data Node... 2009-04-13 08:37:47 [ndbd] INFO -- Unable to alloc node id
    2009-04-13 08:37:47 [ndbd] INFO -- Error : Could not alloc node id at holanda port 1186: No free node id found for ndbd(NDB).
    error=2350
    2009-04-13 08:37:47 [ndbd] INFO -- Error handler restarting system
    2009-04-13 08:37:47 [ndbd] INFO -- Error handler shutdown completed - exiting
    sphase=0
    exit=-1
    Arguments: [holanda --initial ]...
    Error (255)
    [ Apr 13 08:37:47 Method "start" exited with status 95 ]
    [ Apr 13 09:04:02 Disabled. ]
    [ Apr 13 09:04:02 Rereading configuration. ]
    [ Apr 13 09:04:02 Rereading configuration. ]
    [ Apr 13 09:04:03 Rereading configuration. ]
    [ Apr 13 09:04:03 Enabled. ]
    [ Apr 13 09:04:03 Executing start method ("/opt/SUNWvda/lib/vda-db-service start") ]
    Configuration:
    MGMT_NODE=[0]; NDBD_NODE=[1]; SQL_NODE=[0]; MULTI_HOST_MODE=[1];
    NDBD_CONNECTSTRING=[holanda]; NDBD_INITIAL_ARG=[--initial]; NDBD_NODE_ID=[2];
    Starting the Sun Virtual Desktop Infrastructure Database service:
    - Starting Data Node...
    Arguments: [holanda --initial ]...
    Error
    [ Apr 13 09:11:33 Method "start" exited with status 95 ]
    bash-3.00#
    bash-3.00# svcs -l svc:/application/database/vdadb:corefmri svc:/application/database/vdadb:core
    name SUNWvda MySQL Cluster and Application
    enabled true
    state maintenance
    next_state none
    state_time Mon Apr 13 09:11:33 2009
    logfile /var/svc/log/application-database-vdadb:core.log
    restarter svc:/system/svc/restarter:default
    contract_id
    dependency require_all/none svc:/milestone/network:default (online)
    dependency require_all/none svc:/system/filesystem/local:default (online)
    dependency require_all/refresh svc:/milestone/name-services (online)
    bash-3.00# svcs -a|grep vda
    legacy_run 8:58:36 lrc:/etc/rc3_d/S99vda-webadmin-init
    disabled 9:04:02 svc:/application/database/vdadb:sql
    maintenance 9:11:33 svc:/application/database/vdadb:core
    bash-3.00# cacaoadm status
    default instance is ENABLED at system startup.
    default instance is not running.
    bash-3.00# /opt/SUNWvda/sbin/vda-db-status
    Node Type IP/HostName Id Status
    Management node holanda 1 up
    Data node ghana 2 down
    Data node paraguay 3 up
    as I said, the only thing I changed is the value for the redo files, as suggested in one of the replies above.
    This is the second time I uninstall/unconfigure this server and start over (config/install)
    this is a newly installed Sol10 U6 system:
    bash-3.00# uname -a
    SunOS ghana 5.10 Generic_138889-03 i86pc i386 i86pc
    bash-3.00# prtconf
    System Configuration: Sun Microsystems i86pc
    Memory size: 8064 Megabytes
    System Peripherals (Software Nodes):
    bash-3.00# prtdiag | head -10
    System Configuration: Sun Microsystems Sun Fire X4100 Server
    BIOS Configuration: American Megatrends Inc. 080010 01/31/2006
    BMC Configuration: IPMI 2.0 (KCS: Keyboard Controller Style)
    ==== Processor Sockets ====================================
    Version Location Tag
    AMD Opteron(tm) Processor 254 H0
    AMD Opteron(tm) Processor 254 H1
    bash-3.00# swap -s
    total: 876688k bytes allocated + 405180k reserved = 1281868k used, 8752988k available
    help is appreciated.

  • Database not start with srvctl  command in rac 10g

    hi
    when i change parameter in sqlnet file
    SQLNET.AUTHENTICATION_SERVICES= (NTS) to SQLNET.AUTHENTICATION_SERVICES= (NONE)
    then database is not started with srvctl utillity but started with sqlplus enviroment.
    please help in this issue

    user521214 wrote:
    hi,
    we are implementing security policy for our client. our databas is on RAC . As per the security, we need to revoke sys dba priviliges. when i used SQLNET.AUTHENTICATION_SERVICES=(NTS) in sqlnet.ora or SQLNET.AUTHENTICATION_SERVICES=(NONE). the instance not start with the following command in rac 10g.
    $srvctl start database -d abc
    $ crs_stat -t
    Name Type Target State Host
    ora.db.db application OFFLINE OFFLINE
    ora....b1.inst application ONLINE OFFLINE hosttest01
    Edited by: user521214 on Apr 21, 2011 4:08 AMIs this the only parameter you changed? What happens when you undo this modification?
    What do you see on log files?

  • Database not starting up

    HI all,
    I have changed my nls_date format to null with the following command .
    alter system set nls_date_format=null scope=spfile;
    and I restarted my machine.Now my database is starting.It is saying service handler problem and hostdef doesn't exists.
    Can anyone please suggest on this.
    TIA,
    Ravi

    user9502062 wrote:
    HI all,
    I have changed my nls_date format to null with the following command .
    alter system set nls_date_format=null scope=spfile;
    and I restarted my machine.Now my database is starting.It is saying service handler problem and hostdef doesn't exists.
    Can anyone please suggest on this.
    TIA,
    RaviWhy. pray tell, did you set nls_date_format to null?

  • ABAP Database not starting

    Hi All
    We are installing ECC 6.0 with ABAP and Java stack on AIX ,DB2,its a distributed system with CI and SCS on one host and DB on another host.
    When we are trying to start the central instance on CI host during the installation its giving message :
    Checking db Database
    ABAP Database is not available via R3trans
    Starting SAP-Collector Daemon
    20:15:22 15.07.2009   LOG: Effective User Id is root
    This is Saposcol Version COLL 20.94 700 - AIX v10.35 5L-64 bit 070123
    Usage:  saposcol -l: Start OS Collector
            saposcol -k: Stop  OS Collector
            saposcol -d: OS Collector Dialog Mode
            saposcol -s: OS Collector Status
    The OS Collector (PID 229378) is already running .....
    saposcol already running
    ABAP Database db must be started on remote server
    kindly suggest the necessary action.
    Regards
    Arun

    Hi All
    Below is the output of R3trans -d
    SapApp:db2bd1 8> R3trans -d
    This is R3trans version 6.14 (release 700 - 15.06.07 - 15:50:00).
    unicode enabled version
    R3trans finished (0000).
    Also here goes trans.log
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    4 ETW000 R3trans version 6.14 (release 700 - 15.06.07 - 15:50:00).
    4 ETW000 unicode enabled version
    4 ETW000 ===============================================
    4 ETW000
    4 ETW000 date&time   : 17.07.2009 - 02:25:43
    4 ETW000 control file: <no ctrlfile>
    4 ETW000 R3trans was called as follows: R3trans -d
    4 ETW000  trace at level 2 opened for a given file pointer
    4 ETW000  [dev trc     ,00000]  Fri Jul 17 02:25:43 2009
          57  0.000057
    4 ETW000  [dev trc     ,00000]  db_con_init called
          20  0.000077
    4 ETW000  [dev trc     ,00000]  create_con (con_name=R/3)
          34  0.000111
    4 ETW000  [dev trc     ,00000]  Loading DB library '/usr/sap/BD1/SYS/exe/run/dbd
    b6slib.o' ...
    4 ETW000
          48  0.000159
    4 ETW000  [dev trc     ,00000]  load shared library (/usr/sap/BD1/SYS/exe/run/db
    db6slib.o), hdl 0
    4 ETW000
         633  0.000792
    4 ETW000  [dev trc     ,00000]  Library '/usr/sap/BD1/SYS/exe/run/dbdb6slib.o' l
    oaded
    4 ETW000
          30  0.000822
    4 ETW000  [dev trc     ,00000]  function DbSlExpFuns loaded from library /usr/sa
    p/BD1/SYS/exe/run/dbdb6slib.o
    4 ETW000
          33  0.000855
    4 ETW000  [dev trc     ,00000]  Version of '/usr/sap/BD1/SYS/exe/run/dbdb6slib.o
    ' is "700.08", patchlevel (0.110)
    4 ETW000
         232  0.001087
    4 ETW000  [dev trc     ,00000]  function dsql_db_init loaded from library /usr/s
    ap/BD1/SYS/exe/run/dbdb6slib.o
    4 ETW000
          33  0.001120
    4 ETW000  [dev trc     ,00000]  function dbdd_exp_funs loaded from library /usr/
    sap/BD1/SYS/exe/run/dbdb6slib.o
    4 ETW000
          32  0.001152
    4 ETW000  [dev trc     ,00000]  New connection 0 created
          24  0.001176
    4 ETW000  [dev trc     ,00000]  0: name = R/3, con_id = -000000001 state = DISCO
    NNECTED, perm = YES, reco = NO , timeout = 000, con_max = 255, con_opt = 255, oc
    c = NO4 ETW000  [dev trc     ,00000]  db_con_connect (con_name=R/3)
          34  0.001248
    4 ETW000  [dev trc     ,00000]  find_con_by_name found the following connection
    for reuse:
    4 ETW000
          31  0.001279
    4 ETW000  [dev trc     ,00000]  0: name = R/3, con_id = 000000000 state = DISCON
    NECTED, perm = YES, reco = NO , timeout = 000, con_max = 255, con_opt = 255, occ
    = NO
    4 ETW000
          37  0.001316
    4 ETW000  [dev trc     ,00000]  DB2 library successfully loaded DB2 library '/db
    2/db2bd1/sqllib/lib64/libdb2.a(shr_64.o)' successfully loaded
    4 ETW000
        6182  0.007498
    4 ETW000  [dev trc     ,00000]  DB6 (DB2 UDB) UNICODE database interface 700.08
    [opt]
    4 ETW000
          33  0.007531
    4 ETW000  [dev trc     ,00000]  DB6 shared library (dbdb6slib) patchlevels
          19  0.007550
    4 ETW000  [dev trc     ,00000]    (0.8) DB6: V8.2.2 optguidelines in OPEN SQL (n
    ote 150037)
    4 ETW000  [twdydbacc.c ,00566]  db_fd_p<i>.fname:       TRANSLTTXT
          17  0.893509
    4 ETW000  [twdydbacc.c ,00567]  db_fd_p<i>.is_key:      0
          17  0.893526
    4 ETW000  [twdydbacc.c ,00568]  db_fd_p<i>.offset:      185
          17  0.893543
    4 ETW000  [twdydbacc.c ,00569]  db_fd_p<i>.db_length:   1
          17  0.893560
    4 ETW000  [twdydbacc.c ,00570]  db_fd_p<i>.fixed_length:1
          17  0.893577
    4 ETW000  [twdydbacc.c ,00713]  buffer:''
        2543  0.896120
    4 ETW000  [twdydbacc.c ,00718]  i:0
          21  0.896141
    4 ETW000  [twdydbacc.c ,00719]  tw_fd_p<i>.offset:0
          17  0.896158
    4 ETW000  [twdydbacc.c ,00718]  i:1
          17  0.896175
    4 ETW000  [twdydbacc.c ,00719]  tw_fd_p<i>.offset:4
          17  0.896192
    4 ETW000  [twdydbacc.c ,00718]  i:2
          16  0.896208
    4 ETW000  [dev trc     ,00000]  { db_rtab( fcode = 'RT_READ_ONLY', tname = 'TADI
    R' ) {twdbcall.c:648}
    4 ETW000
          45  0.896270
    4 ETW000  [dev trc     ,00000]  } db_rtab( fcode = 'RT_READ_ONLY', retcode = 0 )
    4 ETW000
        5947  0.902217
    4 ETW000 Connected to DBMS = DB6 --- DB2DBDFT = 'BD1' --- SYSTEM = 'SAP'.
    4 ETW000  [dev trc     ,00000]  { db_rtab( fcode = 'RT_INSERT', tname = 'PATCHHI
    ST' ) {saprel.c:1251}
    4 ETW000
         225  0.902442
    4 ETW000  [dev trc     ,00000]  } db_rtab( fcode = 'RT_INSERT', retcode = 0 )
        7328  0.909770
    4 ETW000  [dev trc     ,00000]  dsql_open (con_da=(0,R/3),stmt="SELECT EXECUTABL
    E,SAPRELEASE,H ...",#binds=0,name=UNKNOWN,#input=0)
    4 ETW000
          43  0.909813
    4 ETW000  [dev trc     ,00000]  dsql_fetch (con_da=(0,R/3),cu_id=11,#output=8)
        2658  0.912471
    4 ETW000  [dev trc     ,00000]  dsql_close (con_da=(0,R/3),cu_id=11)
          37  0.912508
    4 ETW000
          38  0.912546
    4 ETW000  [dev trc     ,00000]  } db_rtab( fcode = 'RT_DELETE', retcode = 0 )
        1824  0.914370
    4 ETW690 COMMIT "0" "0"
    4 ETW000  [dev trc     ,00000]  db_con_commit (con_da={R/3,0,0},th_commit=1,tx=1
    ,hold_cursor=0)
    4 ETW000
          69  0.914439
    4 ETW000  trace to file pointer closed
    4 ETW000  trace at level 1 opened for a given file pointer
    4 ETW000
    4 ETW000 ================== STEP 1 =====================
    4 ETW000 date&time        : 17.07.2009 - 02:25:44
    4 ETW000 function         : CONNECT
    4 ETW000 buffersync       : YES
    4 ETW000 clients          : default
    4 ETW000 l.s.m.           : VECTOR
    4 ETW000 commit           : 100000
    4 ETW000 table cache      : dynamic
    4 ETW000
    4 ETW000  [dev trc     ,00000]  Disconnecting from ALL connections:
         174  0.000174
    4 ETW000 date&time        : 17.07.2009 - 02:25:44
    4 ETW000 function         : CONNECT
    4 ETW000 buffersync       : YES
    4 ETW000 clients          : default
    4 ETW000 l.s.m.           : VECTOR
    4 ETW000 commit           : 100000
    4 ETW000 table cache      : dynamic
    4 ETW000
    4 ETW000  [dev trc     ,00000]  Disconnecting from ALL connections:
         174  0.000174
    4 ETW000  [dev trc     ,00000]  disconnected from 'BD1', con_hdl=0
       48503  0.048677
    4 ETW000  [dev trc     ,00000]  Disconnected from connection 0
          44  0.048721
    4 ETW000  [dev trc     ,00000]  statistics db_con_commit (com_total=1, com_tx=1)
    4 ETW000
          30  0.048751
    4 ETW000  [dev trc     ,00000]  statistics db_con_rollback (roll_total=0, roll_t
    x=0)
    4 ETW000
          30  0.048781
    4 ETW000 Disconnected from database.
    4 ETW000 End of Transport (0000).
    4 ETW000 date&time: 17.07.2009 - 02:25:44
    Also thank you markus for your link ,i had gone thru it earlier and the commands are like:
    list db directory and list node directory
    I tried both its working fine
    Best Regards
    Arun

  • Ora-38500 physical standby database not started

    hiiii,
    When i executed the command at physical standby database server.
    it give error:
    To start real-time apply:
    SQL> ALTER DATABASE RECOVER MANAGED STANDBY DATABASE
    2> USING CURRENT LOGFILE;
    Error at line 1:
    ORA: 38500 using current logfile option not available without stand.
    please help me how could i start physical standby database
    Regards
    Vaibhav Dixit

    Hi Vaibhav,
    What exactly do you want to do?
    Alter database recover managed standby database; --->it will be in Manged Recovery mode.
    Alter database mount standby database; ----> it will be mounted, but no log files applies.
    Alter database open read only; ----> it will be open with read only option, but archeive logs will NOT be applied
    If you want to apply the Archive logs which are trasfered from Primary, then you need to fire the below commands
    Alter database recover managed standby database;
    Alter database recover managed standby database using current logfile;
    Alter database recover managed standby database using current logfile disconnect from session;
    To stop applying archives then,
    Alter database recover managed standby database cancel;
    Thanks and Regards.
    tnaresh1982

Maybe you are looking for