RAID Set not showing up - 3 severe events

Intelle Xserve running 10.6 RAID Card running firmware v E-1.3.2.0, Two it drives set up with I think RAID 5.
The main person for the  system is away as well as his backup. So I'm running on very little information at the moment.
Log:
Called in due to user not able to access shared files (Also shared FileMakerpro databases and Portfolio server). Only access to server was via screen share.
Could not connect. After trying all that I could, powered down the server. Restarted, got a login startup permissions error for an item to run at startup. (I'll have to check what exactly that was). Started the Portfolia server and the FileMakerpro databases. Users able to access and use.
Next day same thing. User lost connection with the server. Restarted, start filemakerpro databases and portfoilio services. User able to access.
I suggest pulling over the files needed to work just in case it looses connection again, User starts to pull over some files which is transfering.
About 15 minutes later I get a call that the user lost connection again.
Restart the once again. This time get errors from the RAID utility:
Non-viable RAID set RS1 and all associated volumes are offline
Drive 3:500 missing - Replace immediately or acknowledge loss of RAID set RS1 and associated volumes
Drive 3:500 missing - Previous drive status was inuse
The RAID utility does not show a RAID set.
The drive appear to be OK
The drive shows up on the desktop but when I go into the drive the folders etc are showing. Access the main folder results in a loop where it bails out and just shows the desktop again.
I'm going to get some files to the user from the timemachine backup for now.
Is it possible that the data is OK and maybe the drive are marked off line for the set but still OK?
Any info would be great,
Thanks

Yes the 160GB has the OS. I'm coming into this cold as the main person and the backup are currently away.
I have got the users a work around so they can do thier work. The backup person has very limited email contact and he had thought it was a RAID 5.B  But I would agree this looks to be a RAID 0 or 1 since there are only two drive available for data.

Similar Messages

  • After transferring clips to Final Cut, they do not show up in the events library. They show up in the timeline of my project, though. how can I see then in the events browser?

    After importing clips to Final Cut, they do not show up in the events library. Events from 2014 show up, but not 2015.They show up in the timeline of my project, though. How can I see them in the events browser?

    TThose aren't bins. Those are just groupings based on when the content was created or any other selected parameter. Use the action popup in the toolbar tho change the setting.

  • My internal drive is NOT showing up in the event library in Final Cut X.  I am also getting a "The operation couldn't be completed. Cannot allocate memory" Any ideas? I am using an IMAC Core i7 with 8GB memory, OS version 10.6.8

    My internal boot drive is NOT showing up in the Event Library in Final Cut X. My external raid drive is showing up.
    I am also getting error message "The operation couldn’t be completed. Cannot allocate memory"  when attempting to create a new "event".   Any ideas?
    If I had a application disk, I would unistall and reinstall FCPX.  I am assuming there is a way do do this without a disk - just have not been able to easliy find out how.
    I am using an IMAC Core i7 with 8GB memory, OS version 10.6.8
    Thanks

    Well it did NOT work.  Here is a screen capture as FCPX loads showing the drive while it loads. Then when it is loaded, NO drive showing up in the Event Library ( I have turned off the external drive).
    ANY ideas . . . .  Anybody . . . .  APPLE?

  • IOS 7 Calendar Day View does not show any all-day events ?

    Hi,
    I realize that iOS 7 Calendar Day View  does not show any all-day events.
    Is this a bug ?
    Any help given is much appreciated.
    Thanks and Regards.

    Mine brings me right up to the current time, or in the case of another day, it takes me to the first appointment of the day.

  • Do not show dots for 'free' events in the calendar month view

    I wish I could.... not show dots for 'free' events in the calendar month view. For an overview of when I have hard-scheduled events in the calendar it's pretty tedious and slow to go day -by day, and other views... Instead the dot  in the month view... - why does it show even "free" events? Any ideas, tips?
    Thanks!

    Unfortunately there is no option to disable the dots.
    <Edited by Host>

  • Compound clip imported into project not showing up in the event browser

    I have learnt that when one imports any clip into the project from anywhere else other than its associated event folder, the new clip also gets automatically added into the event folder. I have seen this occur when I had imported audio from the music browser onto my timeline directly.
    Today I happened to place a compound clip [a common template which I use for introduction to the video] onto the beginning of a project which I have started recently. I broke the compound clip apart and made the necessary edits. What puzzles me is that this compound clip has an audio clip and this clip was not being shown in the event browser. Is this normal?
    Ps. I have very recently updated my FCPX from version 2 to 5.
    DR.SOMANNA

    Let me explain the matter in a different way...
    I have made a compound clip of the intitial generator clip, titles and music clip which I had used for my first project. The intention to do so being that I could reuse the same for my future projects as well. I placed this compound clip in a new project which I named as templates.
    When I had started upon a new project a few days ago, I copied and pasted this compound clip from the 'templates project' and added it to the beginning of the timeline of the new project.
    Now, for purposes of editing the titles, I broke apart the compound clip and changed the text of the titles. Also, when I had ungrouped the compound clip, there did appear the music clip below the timeline. I know that clips imported from the generator browser and the titles that are added to the project do not show up in the events browser, but should not the audio clip make its appearance in the event browser? I know that when we add an audio from the music browser, this audio clip will be automatically shown in the event browser.
    My question therefore is this: is an audio track that gets added to the timeline of a project via a compound clip that has been added and ungrouped on the timeline an exception to the rule?
    Hope I have made myself clear.
    DR.SOMANNA

  • Bios not install error and Raid Configuration not showing physcial HDD in Lenovo

    Is this a SATA hard drive by any chance?  Sounds like you have an Adaptec SCSI controller, but no hard drive attached to it.  Are you booting an install DVD of some sort?

    Bios not install error and Raid Configuration not showing physcial HDD in Lenovo RD 120 Server (New)
    updated bios still same error
    and at array configuration it is not showing any hard disk
    hard disk utility it is showing hard disk 
    we are trying to install OS with single hard disk in Lenovo RD 120 Server
    This topic first appeared in the Spiceworks Community

  • OWC RAID 5 not showing up in PPro Media Browser

    Hello all,
    I've seen other threads about OWC RAIDs not showing up in PPro and the solution has been to use the Mac's Disk Utility to reformat the drive.  Disk Utility can't do RAID 5 though and that's what my 16TB OWC Mercury Elite Pro Qx2 is set to.  If I use the File->Import command I can see the OWC RAID but it is not present in the Media Browser (nor in the window that pops up to re-link offline media).   FCP 7, AVIC MC 6.5 and After Effects CC2014 all 'see' and interact with the OWC RAID just fine. The problem seems to be isolated to Premiere's Media Browser function.
    If anyone has a suggested work around I'd love to hear it.

    So it turns out the answer was in front of me all along, just use Disk Utility to format the drive and all is well.
    What threw me was that Disk Utility only does RAID 1 and RAID 0 but since the OWC Mercury Elite Pro Qx2 is a hardware RAID I just set the RAID mode using the switch on the enclosure and then use Disk Utility to format it like I would any other disk.
    The simplicity of the solution coupled with my lack of experience with RAID boxes proved to be my undoing. haha.
    With that being said, I'd still like to see if Adobe can fix the issue w/the default OWC formatting tool.

  • XServe RAID disks not showing up in Disk Utility

    I have a new (to me) xServe RAID box and I'm stuck, the stays lights are green the fiber link light is green on the RAID and not lit on the PCI card but shows up as green in the fiber link section of the settings tool but the RAID array doesn't show up in Disk Utility so I can't format the drives.
    I set up the disks as Enhanced JBOD using RAIDadmin and I've deleted and created it a couple of times, I'm just not sure what else I should try, I've read the manual but. Can't find any suggestions of what's going wrong.
    Thanks

    Port 1: Link Established
    2Gps
    Point to point
    Status light green
    In the system Profiler I'm not sure what you're asking for, I'm running 10.5.8 standard not server.
    the fibre channel shows link established 2Gps and cable type copper but nothing else, the disks & RAID controller don't show up anywhere I've looked.
    RAID Admin shows the JBOD disks as online and lists the LUNs etc.
    System looks fine, only error is missing second power supply.

  • RAID Drive not showing

    Hi there,
    We have an Xserve (Late 2006) running an email server with a RAID5 setup. We had to reboot a week or so ago due to a crash, and since then the Harddrive is not showing up on the desktop, in the finder, in disk utility, or anywhere really. It's like the drive has just dissapeared. However, the server functions fine, and all drives and the drive set are reporting as "Good" in Raid Utility.
    Also, if I navigate to say, the Applications folder, it works fine, just the actual Raid Set is not showing up though
    Anything I am missing here?

    We have a similar problem.
    We had a crash as well. Now the raidutil shows us that all drives are reliable and in good condition. But a task is started: "Long-running task started: Task=RedundancyScrub"
    This is indeed a very long task.. Now running for approx 16 hour and progress is at 32%..
    But the big problem is that the volumes are not mounted.. We do not see the volumes in Diskutil.
    Is there a way to force mounting of the volumes?
    Other question: can anyone explain what 'RedundancyScrub' means and does?
    thanks for any help.
    Regards,
    Ronald
    This all happend on a Xserve Quad core intel Xeon with Hardware RAID
    Message was edited by: rblaas

  • When I sync my iPod to my MacBook through iTunes new events do not show up and old events are not deleted. I am using Snow Leopard  and not iSync.

    I am using Snow Leopard on a MacBook. I have an iPod touch 3G. I do not use iSync it Mobile Me. When I sync my iPod through iTunes new events on my iPod do not show up on my Mac and old events do not delete. I have read help instructions that include deleting the data on the iPod. The iPod has the correct data and the Mac does not so I have not followed those instructions. I need help as the only reason I bought the Mac was to be able to sync, back up, view and print my calendar. Currently it is useless. If only Apple could have learned from the elegance of the Palm software.

    Start here:
    iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows

  • How do I determine the size of an event (cmd I does not show any size for events).

    How do I determine the size of an Event in iPhoto? (Cmd + I does not show size information at the event level).

    If you're running iPhoto 8 (09) select the event and look at the Info pane at the lower left hand corner of the window.  It will give you the number of photos and size:
    for iPhoto 9 (11) open the Event, select all of the photos in it and open the Info drawer at the right by typing Command+i.  The number of photos and size will be at the top of the Info drawer.
    OT

  • Live!Surround speaker setting not showing in surround mixer for SB Live Platinum

    the Li've!Surround option for speaker settings in not showing in my Surround Mixer
    i have:
    Windows 2000 sp4
    SB Li've! Platinum 5.
    ASUS CUSL2
    Sound Blaster Li've! - Li'veDrvUni-Pack (English) SBLW-XPWEB-W4-US 28-Feb-03
    Installed the speaker preset for li've!surround but the only headphone, 2 speaker, 4 speaker, and 5. speaker shows up on speaker configuration of the Surround Mixer
    i've played the AC3 files on the cdrom and Dolby pro logic surround, I get sound from all fi've speakers on my Denon D-850 w/ Dolby surround pro-logic
    I can't use the surround mixer to test all the speakers, only front left and right speakers work on the test, i have to open to wav files directly to test the center speaker, the rear speaker test doesn't work from the wav file
    My Denon system only has analog stereo inputs, so this is my only option for letting Sound Blaster know I have 5 speakers.
    I've uninstalled all SB Li've software and drivers from the unipack, and reinstalled the orignal drivers and apps from the CD-ROM SBP5-CDSD-W-US MID : 32680 5-Sep-2000 and the Li've!Surround speaker setting reappears in the Surround Mixer.
    Is the Li've!Surround setting no longer available in the new Surround Mixer in Li'veDrvUni-Pack (English) SBLW-XPWEB-W4-US 28-Feb-03 ?
    Message Edited by klin on <SPAN class=date_text>2-2-2004 <SPAN class=time_text>06:4 AM
    Message Edited by klin on 2-2-2004 2:45 PM

    so I found this post...
    http://groups-beta.google.com/group/...7?dmode=source
    it seems Li've Surround is no longer supported in the new drivers
    ....so what would be the best setting to play ac3 files or DVD's through my receiver with only 2 analog inputs (left and right) available w/ Dolby surround prologic. Should I set it to 2 speaker or 4 speaker setting in the Surround Mixer in order to send the best signal to the prologic decoder on my receiver with 5 speakers (2 front, center, 2 rear)

  • Iphoto not showing imported photos in events

    I have been using iphoto for quite a while with very few problems.  Recently I have added an iPhone and an apple TV into my apple ecosystem.  I have recently noticed that my iphoto library is NOT showing photos imported from 3rd party sources such as my android phone, in the events section of the interface.  The photos ARE present in the 'photos' section which leads me to believe that they are IN the library.  But when i look at the events and select one say for 3/24 it will only display the photos taken from my wifes iphone and NOT the ones taken from my andriod and imported using the add to library function.  I have attempted all four options in the command-option iphoto startup and have gotten no where. 
    Many of you might that that this is a non issue as the photos are present in the 'photo' section.  but as i prefer to use the fullscreen mode in iphoto i do not have access to the 'photos' tab in full screen, only the 'events'. 
    could my appletv or iPhone or appletv be a contributing factor?  Is there an option in events to only display iPhone imported photos? 
    Any help would be appricaited I am pulling my hair out here.

    1 - Photos and events are simply two different views of the same photos - your iPhoto library - so any photo that is in one is always also in the other - you are just looking in the wrong place
    2 - the most common issue is incorrect dates on photos so you look in the wrong location for the event - in the photos view right click on one of the photos that you are not seeing in an event and show event
    3 - another possiblity is the sort order of the events - verify it under the view menu ==> sort events
    4 - No - it is not your Apple TV nor is it your iPhone
    LN

  • Apple RAID Utility Raid 0 one disk roaming making raid set not viable

    Hello!
    I have a problem with RAID 0. In the picture below you can see that one drive was set to missing and RAID set RS1 has been set to non viable. However all four drives(Bay1-4) are set to be verified with status good. However as can be seen from the picture Bay 3 is set to status: Roaming
    I don't know what I can do here. There was some talk on other discussions but nothing that helped me
    Thanks to anyone that read this and try to help me. If you need more detail I will be more than happy to give them to you. 
    http://shrani.si/f/G/Z9/1KO4CaVc/screen-shot-2012-10-17-a.png
    http://shrani.si/f/41/yG/2o1mIfV/screen-shot-2012-10-17-a.png
    http://shrani.si/f/3p/v/35kiFJyD/screen-shot-2012-10-17-a.png
    http://shrani.si/f/1m/lg/KcXG8j/screen-shot-2012-10-17-a.png
    http://shrani.si/f/1Q/ET/2UkxU4ml/screen-shot-2012-10-17-a.png
    http://shrani.si/f/R/ma/6jYOaty/screen-shot-2012-10-17-a.png

    An error with drive in bay 3 threw it out of the RAID, breaking the Striped RAID. You data will be very difficult to recover, since the data are striped on two different drives, and one of them is no longer part of that RAID set.
    You now need to re-initialize the RAID set (which destroy what is left of the data) using the same or different drives, and restore the data from your backups if desired.
    I recommend writing zeroes to every block on the troublesome drive before even thinking of returning it to service.

Maybe you are looking for