Re: How to disable MIG 7 Traffic Generator in simulation

Hi Everyone,
I was wondering how can I disable vivado traffic generator in simulation?
I have fine tune my DDR channel and need to disable traffic generator for simulation purposes, however, I don't see any option in MIG7 GUI interface, or any parameter that I can pass to traffic generator from my top level simulaion file to stop traffic generator for issuing command and putting random rd/wr data on my  DDR bus.
Any idea?
Thanks,
Mike

Hi,
If you generate the IP alone there will not any tarffic gen, only example design comes with tarffic gen(right click on .xci and choose example design)
So while generating the IP there is no GUI option to disable traffci gen.
But if you attempt to link user deisgn top with memory model then you have to be ultimately careful in passign the parameters and mapping the signals
instead if you are running MIG example design simulation but wanted to drive your own tarffic,  you can simply commet out tarffic gen in example_top and have your own fsm for driving the MIG user intefrace.
Hope this helps
-Vanitha

Similar Messages

  • How to disable Firefox form generating a thumbnail on the tab when open an image url.

    Hello, I have recently installed Firefox 33.1 and noticed that, when I open an image on a new tab, some of them will show a thumbnail of the image I opened on the tab, while others don't.
    I am wondering, if there is a way to stop Firefox from making these thumbnails?
    Thanks.

    Feels like if an image is larger than around 1000 pixel on one side, it won't have a thumbnail.
    For example:1500*1500, 1362*768 don't have a thumbnail, while 1024*768 do.

  • Urgent Traffic generator.....

    Can anyone tell me how to make a traffic generator?
    Description of generator: I want to make a traffic generator to generate packets in order to test the network traffic.
    Thx for everyone to help me...

    So, if you've a list of machine IP's and the ports being listened to by each, I suppose you could write up a program that sends random data to each, possibly tailoring it to the port being written to (HTTP, Telnet, FTP, etc). Or, you could distribute a program to all machines on your network that listen on a well-known port and send data to them. I don't see why you can't just write up a shell script that pings all manner of machines on your network, maybe adjusting the packet size as you like. It shouldn't be too hard to run through your /etc/hosts file and shoot pings at the machines to simulate traffic, right?
    Lee

  • How to disable some of the table fields in Table Maintenance Generator

    HI,
    I am creating one table which contains 10 fields.
    But i wanted to disable some 2 fields in Table maintenance generator.
    So can any one plz tell me how to disable those 2 fields.

    Generate a maintenance view for the table,
    Goto- Table/Join Conditin Tab-- Put the name of your table 
    Goto-viewfield tab--- Put the fields whatever you required. 
    Then generate table maintenance for the view created.
    pls chk
    Thanks
    Anurag

  • How to disable extra visit to portal server

    hi Experts,
    I am using wcp11.1.1.8, in a customized page template with portal builder, I used an EL expression to generate link like this:
    "http://localhost/webcenter/portal/Portal1/page1?_adf.ctrl-state=1dvjebskda_596"
    I clicked this link, using httpwatch to monitor network traffic, found IE visited portal server twice: first visit is a "Get" method for ""http://localhost/webcenter/portal/Portal1/page1?_adf.ctrl-state=1dvjebskda_596"", result code is 200, the second visit is a "Post" method for "http://localhost/webcenter/faces/oracle/webcenter/page/scopedMD/s64679523_e5d0_454a_952a_55128e607e07/Page7.jspx?wc.contextURL=/spaces/Portal1&_adf.ctrl-state=1dvjebskda_596", result code is 200.
    If I paste this url "http://localhost/webcenter/portal/Portal1/page1?_adf.ctrl-state=1dvjebskda_596" to ie addressing  field, and press return, httpwatch showed me there is no "second visit" for "/faces/oracle/webcenter/page/scopedMD/s64679523_e5d0_454a_952a_55128e607e07/Page7".
    Seems the "second visit" is auto generated by portal framework, how to disable it?
    Best regards

    Hi.
    Sorry about the delay, I was too busy and I only could do a small testing.
    I was checking quickly how WebCenter Portal (formerly Spaces) works with links compared to Framework Portal.
    The responsible of the "possible twice visit" is the following ViewHandler: oracle.webcenter.webcenterapp.internal.view.navigation.NavigationViewHandler in spaces-model.web.jar (method getPageTargetViewId, getActionURL and also isRedirectRequired).
    First of all, try to check that you're Pages have the "Redirect" checkbox unchecked (or you're navigation-model links). In case of being checked it will be 2 Requests.
    There are following behaviors:
    Using <af:commandLink> just will navigate using PPR and doing a POST.
    Using <af:goLink> using goLinkPrettyUrl there are many behavior:
    Already wc.contextURL is present in the URL and then it will call just one GET.
    If not is present, getActionURL it will add it in order to maintain the correctly the relationship Page - Space. It will generate you're behavior.
    I'm trying to understand why sometimes just call one GET and why sometimes generate a GET,POST,GET behavior.
    Anyway if it's urgent open a SR to Oracle.
    I think that If you try to add to your goLinkPrettyUrl the wc.contextURL parameter it just should do a visit once time (one GET). Try it if you have free time .
    I hope this information helps.
    Regards.

  • How to disable CHARGES tab in Find Sevice Requests(CSXSRISR.fmb / CSXSRISV)

    could any one please let me know how to disable CHARGES tab in Find Sevice Requests ( CSXSRISR.fmb, but funtion registered is CSXSRISV).
    Actually when i access the "Create Service Requests" menu option, the form comes up with a the three TABS (Charges , Work Orders & Maint Req) visible but disabled. But when i access the same from "Find Service Request" menu option, i get the Charges TAB enabled but not the other two... so i would need to visibilly disable the CHARGES TAB like the other two tabs.
    I checked the subfunctions but i could not find any.... i could only find Update Charge and Create Charge options but not the Visible option.

    Hi...
    The Charge Tab in SR form gets enabled only after SR No. Generation.
    So initially when you open the Service Request form the Charges Tab will be visible but disabled, & once the SR number is generated the same gets enabled.

  • How to disable CHARGES tab in Find Sevice Request ( CSXSRISR.fmb ).

    could any one please let me know how to disable CHARGES tab in Find Sevice Requests ( CSXSRISR.fmb, but funtion registered is CSXSRISV).
    Actually when i access the "Create Service Requests" menu option, the form comes up with a the three TABS (Charges , Work Orders & Maint Req) visible but disabled. But when i access the same from "Find Service Request" menu option, i get the Charges TAB enabled but not the other two... so i would need to visibilly disable the CHARGES TAB like the other two tabs.
    I checked the subfunctions but i could not find any.... i could only find Update Charge and Create Charge options but not the Visible option.

    Hi...
    The Charge Tab in SR form gets enabled only after SR No. Generation.
    So initially when you open the Service Request form the Charges Tab will be visible but disabled, & once the SR number is generated the same gets enabled.

  • How to Disable Row Detail in Sales Module

    Dear Experts,
    how to disable row detail option in sales module. how it is posible. we are using SAP Business One 2007. PL42
    Thanx

    AOA Rahil,
    I have just solved this problem, I was also facing the same one
    I am using B1DE, I have handled this on before menu click when open the form
    <B1Listener(BoEventTypes.et_MENU_CLICK, true)>  _
            Public Overridable Function OnBeforeMenuClick(ByVal pVal As MenuEvent) As Boolean
                'GENERATED CODE
                Me.LoadForm()
    1***            Dim Form As Form = B1Connections.theAppl.Forms.ActiveForm
       2 ***        Form.Settings.EnableRowFormat = False
                Return false
            End Function
    1--Capture the current form
    2--Disable Row Detail Form
    It worked for me
    Best Regards,
    Umer Nasim Mirza
    03004003633

  • AMFPHP and AS3FLEXDB - how to disable 'busy indicator' during query execution ?

    I'm doing some experiments with Flex and SQL with use of as3flexdb and AMFPHP.
    I've written some application which is pushing some data to SQL base...
    problem is, that durring query execution, there is some 'busy indicator' on the screen
    - some circle, and word 'loading'.
    Have you any idea how to disable this ?
    Everything what I'm doing is based on this tutorial below, but there is no idea in it how to
    disable the indicator.
    http://ghalex.com/blog/tag/as3flexdb
    I'm not sure if this indicator comes from as3flexdb libraries or AMFPHP itself ?
    Has anyone of you had such problem before ??
    Thanks for all ideas
    Rymas,

    Unfortunatelly my cheers was to early
    I've successfully decompiled the library swc file, found Query.as class and corrected things mentioned in this
    post : http://itutorials.ro/viewtopic.php?f=9&t=22&p=59&hilit=loading#p59
    ... but I cannot compile the library.fla back to swf ... it's generating some errors
    Could anyone help me with that, maybe you've got more expirience with decompiling and compiling.
    Orginal .swc file is here : http://www.rymasek.iq.pl/swc/as3flexdb_1.3.0.swc
    Thanks for help !!

  • How to disable the option of Resart for application error in SXMB_moni

    Hi Experts,
    I have a scenario of JDBC to Proxy.In this we have created Fault message type to capture any error.The requirement is to disable the option of Restart in SXMB_MONI for application error generated with Fault message.We have made coding for generating application error in inbound proxy code.Looking for a quick reply.
    Thanks
    Deepak

    Hi Mayank,
    I am looking for disabling the "Application Error" generated from Fault message of inbound proxy to "Resart" using Resart button in SXMB_moni of Application system ECC.what I am referring to is how to disable u201Crestartu201D (not resend) of the messages in SXMB_MONI if they have errors.
    For example, the interface to load some entries calls a proxy which may load some messages successfully and some may result in errors. This would appear in the SXMB_MONI with application errors with restart capability. If the user restarts the message it will post the entries again which were successfully posted earlier. We would like to prevent this from happening.
    Thanks
    Deepak
    Edited by: deepak jaiswal on Mar 2, 2010 5:19 PM

  • How to Disable Telnet on IPS?

    To whom it may concern,
    Good day, I hope your week is going well.  I recently discovered that my IPS sensors are listening for and accepting telnet traffic.  I looked at the configuration in the CLI, and it is disabled; however, when looking at the listening services via the Service account, I see that the sensor is indeed listening for telnet; please see below.
    Does anyone know how to disable telnet?  Do I need to modify the \etc\inetd.conf file in the Service account and then reload inetd to take effect?  Thanks.
    Telnet Disabled by default in the CLI:
    sensor(config-hos-net)# show settings
       network-settings
          host-ip: x.x.36.45/24,x.x.36.3 default: x.x.1.2/24,x.x.1.1
          host-name: sensor default: sensor
          telnet-option: disabled default: disabled
    Telnet listening for telnet per netstat –na performed on the Linux partition:
    -bash-2.05b$ netstat -na
    Active Internet connections (servers and established)
    Proto Recv-Q Send-Q Local Address           Foreign Address         State     
    tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN     
    tcp        0      0 0.0.0.0:23              0.0.0.0:*               LISTEN     
    tcp        0      0 0.0.0.0:7000            0.0.0.0:*               LISTEN     
    tcp        0      0 x.x.36.45:443           0.0.0.0:*               LISTEN     
    tcp        0     36 127.0.2.1:7000          127.0.1.1:1139          ESTABLISHED
    tcp        0    268 x.x.36.45:22            x.x.251.209:12299       ESTABLISHED
    udp        0      0 0.0.0.0:32768           0.0.0.0:*                          
    udp        0      0 0.0.0.0:161             0.0.0.0:*                          
    udp        0      0 127.0.2.1:123           0.0.0.0:*                          
    udp        0      0 x.x.36.45:123           0.0.0.0:*                          
    udp        0      0 127.0.0.1:123           0.0.0.0:*                          
    udp        0      0 0.0.0.0:123             0.0.0.0:*
    Jonathan

    Hi Jonathan.
    I recently discovered that my IPS sensors are listening for and accepting telnet traffic.  I looked at the configuration in the CLI, and it is disabled; however, when looking at the listening services via the Service account, I see that the sensor is indeed listening for telnet; please see below.
    When Telnet is Disabled (which is also the default on modern versions of the sensor software), the sensor's firewall configuration includes a rule for dropping Telnet traffic:
    -bash-2.05b# iptables -L INPUT -nv
    Chain INPUT (policy DROP 0 packets, 0 bytes)
    target     prot opt in     out     source               destination        
    DROP       tcp  --  ma0_0  *       0.0.0.0/0            0.0.0.0/0           tcp dpt:23
    ACCEPT     all  --  ma0_0  *       0.0.0.0/0            0.0.0.0/0          
    ACCEPT     all  --  ma0_0  *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED
    If Telnet is Enabled, then that specific rule is removed (allowing incoming Telnet traffic to reach the daemon):
    -bash-2.05b# iptables -L INPUT -nv
    Chain INPUT (policy DROP 0 packets, 0 bytes)
    target     prot opt in     out     source               destination        
    ACCEPT     all  --  ma0_0  *       0.0.0.0/0            0.0.0.0/0          
    ACCEPT     all  --  ma0_0  *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED
    NOTE: In the above examples, the sensor's configured access-list contained a single entry (access-list 0.0.0.0/0); the above outputs will vary depending on the the sensor's access-list configuration, but the behavior still applies.

  • Forms personalisation - Vendor Form - How to Disable a Tab Page

    Hi,
    I am not a Forms 6i/9i programmer, although I have an appreciation of the concepts and can look at forms in Form builder. I have been looking at forms personalisation and have used it to execute plsql via the built in 'execute a procedure'. I can also see how to disable blocks, or items, but I haven;t managed to disable a form tab page i.e. On the vendor form there are tabs for GENERAL, CLASSIFICATION etc.
    I have tried using the object type Tab Page, but the poplist doesn;t list any tab pages. Also if you choose Canvas, the list of Canvases appears but generates errors when you try and use the form (complaining of tab page ids).
    I understand that to disable a tab page programatically, you would use SET_TAB_PAGE_PROPERTY i.e. in a forms trigger or in CUSTOM.pll
    I would have thought Forms personalisation could do this.
    Any ideas would be appreciated
    mark
    I under

    What you can do is hiding the tabs (see pic below) and force the active tab programmaticily
    Hope this helps
    Message Edité par TiTou le 09-20-2006 10:35 AM
    When my feet touch the ground each morning the devil thinks "bloody hell... He's up again!"
    Attachments:
    Clipboard01.png ‏151 KB

  • How to disable Tabs in the application

    Hi OAF Guys
    How to disable tabs in the application? if any one knows reply asap
    Thanks in advance

    Tabs are generated by the menu structure, if you want your page not to have tabs, have a responsibility with a menu which does not have any levels of submenus and just has your page as a function in the menu.
    Thanks
    Tapash

  • KSFETCH- causing massive slowdown on MDD 10.5x - how to disable

    GOOGLE IS PLAYING THE SLIME MASTER ROLE
    Below are several examples of how to disable this bull roar
    from taking precious system resources.
    EVEN ON OLDER MACS - (I used MDD running 10.5x)
    This started happening to me probably around May or June.
    My computer was Held down in some unknown process and then
    I installed Little Sntich - and BINGO it's KSFETCH the little
    hidden installer that is accessed multiple times daily by Google
    to (?).
    My computer was rendered almost unusable when these updates would occur
    and it was HORRIBLE because they happen so frequent.
    Does anyone know why LITTLE SNITCH does not have a
    simple area where you can have the Name blocked as
    KSFETCH ? Instead of the IP ect? I thought it would have this feature
    but no  and KSFETCH gets around this with Keystone
    by changing the IP last digit every call.
    Amazingly simple and effective.
    Google is the robot to fear.
    IMPORTANT
    THERE ARE AT LEAST  2 library folders.  (depending on how many users on system)One for root user (current user) and one for
    administrator (master file set)
    You want to target your Master file set first and then do your users LIbray folders.
    method 1:
    USING TERMINAL :
    http://forums.obdev.at/viewtopic.php?f=1&t=6720
    by buzzart » Fri Jun 29, 2012 4:27 am
    To stop the ksfetch (Google's auto-updater software) from checking every hour run the following in terminal:
    defaults write com.google.Keystone.Agent checkInterval 604800
    604800 is a week in seconds. Divide by 7 to check daily.
    Keystone agent is generating a new temporary executable file on each update check. This is why Little Snitch is asking repeatedly for permission. If Little Snitch were updated to allow regex for name checking then this could be solved. No doubt this would introduce other issues that would need to be considered.
    method 2 :
    USING TERMINAL :
    I have deleted files in LaunchAgents and made the Google files inaccessible = permissions 000 and ksfetch keeps running every hour. The "Do No Harm" company is full of it.
    method 3 :
    MANUAL method
    Go to /Library/Google/ and copy it to your desktop. delete GoogleSoftwareUpdate, Lock it and replace it with your old one.
    method 4 :
    MANUAL method
    first go to your home folder, then to the library folder.  Inside the library folder you will find a folder called Google.  Inside the google folder there is a folder named GoogleSoftwareUpdate.  Highlight this folder and click cmd  i.  The window that pops up is what you need.  At the bottom of this window, you will find sharing and permissions. This is where you would change the settings for the folder. 
    That is cmd plus the i key. (⌘+i) simultaneously.
    The same dialogue box can be accessed by right-clicking on the folder and selecting 'get info'.
    Incidentally, if you trash the contents of the folder and then lock the folder (checkbox at the top of the info window) that will also prevent anything being written to it.

    This seems to be a better / easier way.  In finder go to /Users/YourUserName/Library/Google
    Then right click "get info" or CMD I and change the permissions on the "Google Folder" too read only and lock it.
    You can also do this via terminal for advanced users.
    This  works for Hands Off or Little Snitch in fact you can delete "all the  rules" for KsFetch and it hasn't come back for me in a long time.
    This  may interfere with Google software updates so if your Google stuff  breaks just change the permissions back and update. Then change back if  necessary.
    You can also use the wildcards in Hands Off and  Little Snitch they do work as well. If you the recent versions. Google  it to learn how to use the wildcards.

  • How to disable wifi for MAC desktop?

    This is probably a very simple process.  I just need a little direction.  Does anyone happen to know how to disable wifi on a MAC desktop when using an ethernet cable versus wifi?

    EDIT: If the stuff below seems more complicated than you wish to be involved in, feel free to ignore it.
    The Mac will send packets bound for the Internet to the Top-Most ACTIVE interface listed in the left side of the box at:
    System Preferences > Network
    If you set the 'Service Order' to have Ethernet at the top, whenever Ethernet is working, Wi-Fi will be ignored.
    Set Service order is available using the gear Icon at the bottom of that box.
    So all my Internet traffic is going over my Ethernet connection, even though Wi-Fi is still connected and nominally "active".

Maybe you are looking for

  • Administering Express basestations across subnets

    Hi all Should I be able to administer an Express base station sitting on a different subnet on a different physical LAN within our building (originating from a different port on the router)? I can see and administer the Express base station while it

  • How to import wmv video tracks in Premiere Pro CC on mac?

    Hi, Is there a way to import wmv video files in premiere without converting them before? I'm aware, that exporting is another topic, i'm only intrested in importing. I only found the information, that AME is able to import WMVs after installing Windo

  • WebI XI 3.1 Client with XI2 SP1 Server

    Hi I'm trying to get an installation of WebI XI 3.1 working.  We have XI2 SP1 on our server. I have installed the software, when I try to login I get the error message saying "login failed." When I try to update the licence key on the CMC I get the f

  • Confirmation of changes before pagination

    1. I have a report with a checkbox added to each row (generated with apex_item.checkbox function. 2. As pagination I use "row ranges ... in select list with pagination" Now I would like the application to ask the user, if he/she really wants to leave

  • Printing Frames from hdv 720p footage

    I am doing a project which requires me to print out frames of footage I have shot onto a4 and a3 paper, When I tried to print going into quictime + selecting print i got tiny images and i need to get full a4 and a3 sizes. Is their an easy way to just