Realtek 8188EE wifi card alternative for 15-f018ca
I need to replace the unreliable Realtek 8188EE wifi card that came with my laptop.
How do I find a wifi card that is compatable with my computer?
Thanks,
Bob.
Hi @bbigbob
Welcome to the HP Forums!
It is a wonderful place to find answers and information!
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
I understand you would like to know what wireless cards are recommended for your system as you would like to replace the current one.
Here is a link to the HP 15 Notebook PC Maintenance and Service Guide. Please note Chapter 5 page 32 for the recommended replacements
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!
Similar Messages
-
AC wifi card upgrade for dv7-6b77dx?
Hi. I'm considering purchasing a router utilizing the new AC wireless standard and I'm wondering if there are any AC wifi cards that are approved for use in the US with the dv7-6b77dx? I was looking specifically at the Intel 7260HMW but if there's any other AC wireless card that's approved for use I'm open to alternatives.
If there aren't any currently approved for use, is there any expected timeframe when one will be? Thanks.
This question was solved.
View Solution.Thanks Huffer. I thought that was probably the case but figured I'd just check anyway. Good info though to know that HP doesn't add new wifi cards to the approved list with bios updates. Not what I wanted to hear of course but at least I know now not to wait for that and go with a USB adapter instead if AC wireless is something I really want.
FYI though for anyone else considering this upgrade, I just tested an AC USB adapter from my local Best Buy along w/a new AC router and I wasn't that impressed (great at short range but no better and actually worse than N at a distance which is what I really wanted it for). Maybe that was just the router and adapter I tried (both Linksys) but for now I've decided to just return those and stick with the laptop's Centrino N card. -
ok so heres the problem. cingular offers a wifi card that would just plug into a pci slot on a pc laptop for internet access all over the nation. http://onlinestorez.cingular.com/cell-phone-service/cell-phones/phonedetails.jsp ?id=cdsku9870019
pretty sweet stuff. now the box of the card only lists windows capability, but what i was wondering is if mac powerbooks have slots similar or equal to that of which i would find on a pc, or if there is an adapter that is made for such. the reason i dont know this is casue i dont own a mac as of now but i am a realestate agent and am planning on buying a laptop and i have my heart set on mac. i just need to make sure all my business needs are met, and this is one feature that i would find advantages. thanks for all your help.Only the 15" and 17" PowerBooks have CardBus slots which you can insert PC cards into.
Your link does not work (asks me for my zip code which I don't have), so I can't work out which Cingular product you are referring to.
These links may be informative.
iFelix, "Help for Wireless Cingular GC3 Edge Card for MAC" #1, 08:51am Jun 16, 2005 CDT
http://discussions.info.apple.com/webx?128@@.68b6953d -
5 GHz wifi card replacement for dv7-6c23cl (AMD A8)?
Laptop came with Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter. It has Broadcom 20702 bluetooth adapter. Not sure if its build in to the wifi card. I'd like a dual band better card. I have WNDR3000 Netgear dual band router. This adapter connects only at 65Mbps max. with 2.4n. Any successful upgrades? Please help.
This question was solved.
View Solution.You're very welcome.
You can look at the service manual at the link below and in chapter 3 you will find an illustrated parts list with all components you can purchase with the HP part numbers.
http://h10032.www1.hp.com/ctg/Manual/c03099448.pdf
Then to buy a part, you can enter the part # in the site below in the applicable box.
http://h20141.www2.hp.com/Hpparts/Default.aspx?mscssid=29A6F8A626224D4583A5DD74EF3A2FAF
When you see the wireless cards available, the dual band card you see is only for notebooks with Intel processors--and it doesn't matter, as the part number for that card is incorrect and nobody knows what the right one is.
Changing a wireless card in an HP consumer notebook is nothing short of a nighmare due to the BIOS lock out of any cards not listed in the service manual for the specific model notebook.
Paul -
What replacement wifi card do i need for iMac 21.5-inch EMC 2308 late 2009 model
Need to replace wifi card. For the life of me, I can't find the exact model # of wifi card I will need. Only that I need "AirPort Extreme (802.11g/n)," but when I search for that, I get all sorts of different shaped and sized cards that meet those specs.
I would try giving them a call at their support number. They may be able to help both identify the correct part and know where you can get a replacement. In addition, you may also want to consider getting a wireless USB adapter. You would use this instead of the internal card. There are a number of vendors providing these as well.
-
Error when installing new wifi card. g50-70
Tired of having a crappy Realtek based wifi card I bought an Intel 7260 AC card as I'm upgrading my home network.
However when I install this industry standard m.2 card into it's industry standard m.2 slot and reboot.
I then get an Unauthorized Network Card message.
How do I fix this error message? It's just absurd.Hi plupien79, welcome to the forum.
According to your Hardware Maintenance Manual, page 80:
http://download.lenovo.com/consumer/mobiles_pub/lenovo_g_z_50_series_hmm.pdf
These are the cards certified to work in your G50-70:
WirelessLan_Non_Intel, Ltn NFA335 1x1BN+BT4.0 PCIE M.2 WLAN FRU 20200558
WirelessLan_Non_Intel, Cbt BCM43142 1x1BN+BT4.0 PCIE M.2 WLAN FRU 20200557
WirelessLan_Non_Intel, Cbt RTL8723BE 1x1BN+BT4.0 PCIE M.2 WLAN FRU 20200570
WirelessLan_Non_Intel, Ltn NFA345 1x1AC+BT4.0 PCIE M.2 WLAN FRU 20200579
WirelessLan_Non_Intel, Cbt BCM43162 1x1AC+BT4.0 PCIE M.2 WLAN FRU 20200573
WirelessLan_Intel, Intel 3160 1x1AC+BT PCIE NGFF WLAN FRU 20200418
Any other card will not pass the BIOS white list. Please note the FRU number for these cards. You can't install an "off the shelf" card, without the Lenovo branding. When buying a card, make sure it's expressly stated that it will work in a Lenovo Idea system.
Cheers
DragonRider
I'm DO'ing IT
Lenovo Y470 085525U 2nd generation Intel® Core™ i7-2630QM processor ( 2.00GHz 1333MHz 6MB )
IdeaCentre A520 Intel® Core™ i5-3230M processor ( 2.60GHz 2600MHz 3MB )
YOGA Tablet 2 Pro-1380F
X1 Carbon 2nd Gen (20A8) ThinkPad + T420 -
Thinkpad t500 and wifi card realtek RTL8192SE[solved]
I Buy a Lenovo Thinkpad T500 and the wireless adapter does not work in linux.
11b/g/n Wireless Lan Mini-PCI Express Adapter II.
lspci say:
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
lspci -n:
03:00.0 0280: 10ec:8172 (rev 10)
I need to buy another usb, pcmcia or mini pci-e wireless card.
Can you recommend one that works well? Because I never work with wifi cards on linux.
sorry my poor english
EDIT 21/07/09: add more information (thinkwiki):
http://www.thinkwiki.org/wiki/ThinkPad_ … Adapter_II
EDIT 22/10/09:
Finally came the expected driver, I think it's premature but it works perfectly.
Here the driver (r8192se_pci):
32bits: http://launchpadlibrarian.net/33927923/ … 009.tar.gz
64bits: http://launchpadlibrarian.net/34090326/ … bit.tar.gz
untar; make; make install; reboot and enjoy it
I test it with:
netcfg
standar commands:
ifconfig wlan0 up
iwlist wlan0 scan
iwconfig wlan0 essid MySsid
wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf
dhcpcd wlan0
The first time I compile the module, function correctly, but after scan for available networks I haven't any results.
Recompile and everything worked again
[b]I edit the wiki, pleased read it and help me because my English is a bit basic.
thanks
Last edited by takedown (2009-10-23 00:55:44)Please note that the T500 has different hardware configurations.
Other options in wireless card (for the T500): intel 5100 - intel 5300.
This models work fine under linux
lspci -vv:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Lenovo Device 20e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f4400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 41c9
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f4200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Lenovo Device 20e6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc226800 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: heci
Kernel modules: heci
00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) (prog-if 85 [Master SecO PriO])
Subsystem: Lenovo Device 20ea
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 1828 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 1820 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 1810 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel modules: ata_generic, pata_acpi, ide-pci-generic
00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) (prog-if 02 [16550])
Subsystem: Lenovo Device 20ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1830 [size=8]
Region 1: Memory at fc024000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: serial
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fc025000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable+
Address: 00000000fee0300c Data: 41c1
Capabilities: [e0] PCIe advanced features <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1860 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fc226c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Device 20f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fc020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 0, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4300000-f43fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 1, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 3, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=14, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f4100000-00000000f41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 4, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4181
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 18c0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 18e0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fc227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 00005000-00008fff
Memory behind bridge: f4800000-f7ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Lenovo Device 20f4
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Device 20f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device 20f8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at 1c48 [size=8]
Region 1: I/O ports at 183c [size=4]
Region 2: I/O ports at 1c40 [size=8]
Region 3: I/O ports at 1838 [size=4]
Region 4: I/O ports at 1c20 [size=32]
Region 5: Memory at fc226000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Mask- 64bit- Count=1/16 Enable+
Address: fee0300c Data: 4199
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Device 20f9
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc227400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
Subsystem: Lenovo Device 20c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4800000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: 80000000-83fff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 20c7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f4801000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
15:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
Subsystem: Lenovo Device 20c8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f4801800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
15:00.3 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
15:00.4 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 11)
Subsystem: Lenovo Device 20ca
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
15:00.5 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 11)
Subsystem: Lenovo Device 20cb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME- -
Replacing the Realtek wifi card with an Intel one
Hey everyone,
I am trying to replace the poor performing realtek wifi module with an Intel Centrino one on my T420.
I purchased an "Intel Centrino Advanced-N 6205" which is one of the chips the T420 comes with.
Apparently my chip is not whitelisted, as I could not boot with it plugged in.
Lenovo support was unable to tell me where to get a Lenovo branded chip.
Can anyone help me out?
Thanks in advance!
Solved!
Go to Solution.Hello and welcome,
As you've discovered, wifi cards have to be the correct model (Intel xyz) and have a Lenovo FRU number.
I can't link to the T420 Hardware Maintenance Manual at the moment - support is undergoing maintenance
Here are the Intel models and FRUs from my local T420 HMM:
Wireless-N 1000 60Y3241
Advanced-N 6205 (2x2 AGN) 60Y3253
Ultimate-N 6300 60Y3233
Advanced-N + WiMAX 6250, WW SKU 60Y3195
Advanced-N + WiMAX 6250, Russia SKU 60Y3209
Hopefully that helps your search.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество -
G4 support for Airport Card alternative?
Hi all,
It never dawned on me that there is an alternative to Apple's Airport cards for our systems until recently. I have a G4 dual 1GHz system which houses a hookup for the original airport card; the system also has PCI slots. I have an Airport Extreme Base station and would like to restrict my frequency range to the 5 GHz ONLY (to avoid the crowding of 2.4 GHz range.) So, is it correct to say that my G4 is not tied down to the original airport card but can theoretically use "n" capable WIFI cards via on board PCI or USB? And if so, any you would recommend? Also, how's the software support for it, i.e., drivers, Airport Utility, etc. since the card would be third party and not Apples? Would I get the support from say, Airport Utility as if I had an Apple airport card in there or are there going to be compatibility issues? Many thanks!OK, I just found this out:
http://www.beowulf.org/archive/2001-July/004174.html
32 bits/33 Mhz : aggregated ideal peak at 132 MB/s
64 bits/33 Mhz : aggregated ideal peak at 264 MB/s
And that's shared between all items on the PCI bus.
It would be interesting to measure the bandwidth on the USB 2 PCI card. I've seen it vary wildly on a G4/400 Mhz Yikes, sometimes dropping to as little as USB 1.1 even with only one USB item connected on an IOGear card. I no longer have access to that machine. That's of course assuming nothing else is sharing the same bus. -
Whitelist of Wifi cards in BIOS (F29) for DV& 4010TX
I need to replace my current single band wifi card and have tried the alternatives listed in the user manual. On boot BIOS returns "incompatible wifi device system halted"
I have tried 3 different Broadcom cards and an Intel card with the same results. ALL of the ones I have tried are supposed to work (as per user manual)
What will work
This question was solved.
View Solution.Hi @zigzag3143
I saw your post regarding the problem you are having after installing the wifi cards listed in your user manual. At this point I would recommend that you give us a call regarding this issue. You can reach HP Total Care at 1-800-474-6836 in North America or start here if you live outside of North America.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP -
I have a dv4-2180us and I want to change out the wifi card for one w/ bluetooth and 5G
Product name dv4-2180US. My wifi card is intel wifi link 1000 BGB, and I'd like to switch it out to an intel 6230 that has both. Is it possible to modify the BIOS? I have upgraded my BIOS to the most recent 55454 hoping that would correct the problems with the keyboard...which it has not...but I'm far more interested in making full use of my network., Thanks.
I can tell you that you need to make sure the form factor is the same on the new as the existing one.
The bios really has no bearing on it. Its hardware thats compatible with hardware.
Parts like that are not readily available to swap from machine to machine. There are standards for which the card interfaces to the machine and thats why I mentioned the form factor of the card.
Physical dimensions are also to be noted, as some cards are larger than others with the same form factor.
You really have to do your homework and research to see what will work.
Your machine may already have a slot availble for a bluetooth board, or fingerprint reader as those are both viable options.
You are not likely going to get bluetooth and wireless n on the same card anyways. I would suggest looking for a dual band wireless n card and seeing if you have another slot to put a blutooth module into.
Another option is to get a type 2 cardslot module and just insert it when you need it. If your machine has this type of external cardslot it may be your cheapest option. -
Yoga 2 11 support for new AC Wifi card
I just recently upgraded my Yoga 2 11 with a new Crucial MX100 512 GB SSD. While in the laptop, I pulled the factory Wifi card and bought and installed the Intel Dual-Band Wireless AC 7260. I get the dreaded error on bootup that it has detected a unsupported wi-fi card. Is there a supported AC card for this machine, or plans to support this Intel card?
The top card is what came from the factory (real piece of junk), and the bottom is the new Intel card.Have you considered looking at what's available in the Lenovo Outlet ?
Here's one example, Y11s Haswell: http://outlet.lenovo.com/outlet_us/itemdetails/59RF0542/445
Listed as a refurb. My experience with refurbs from the outlet is that I couldn't tell them from 'new'. YMCV.
Happy Hunting!
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee. -
Compatible WIFI card for Thinkpad a21m, wifi orinoco silver no longer working
Thank you for having this forum available.
My husband passed down his Thinkpad A21M Type 2628-GTU to our son. The wifi card that was with it is a Lucent Technologies Orinoco Silver 11mbit/s t/n 03549501 p/n012938/c. When powered up last night, the ethernet was fully functional, but the wireless card didn't connect to the net. My husband assumed the Lucent card was bad. Is there something compatible I may buy to replace it? Do you have a suggestion on what he might have missed in trying to get it to work at home?
He has used this laptop all over the country including at home before, so I would imagine he knows what he is doing. But, we do have a new service provider since the company upgraded his computer system.
Thank you so much!Welcome to the forum!
Honestly, it's time to upgrade to a newer card anyway, at least b/g. Any PCMCIA wireless card will work with your A21m, it all depends on your router, and your personal preferences.
Hope this helps.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you. -
I spilled some red wine on my keyboard and i cannot connect to the internet any more. it says on the internet icon: Wi-fi: no harware installes. so i guess i need to get a new wifi card for my mac air. do i have to buy this from a apple store? i live fare away from an apple store. Also, I do have a macbook with software system:
System Version: Mac OS X 10.6.8 (10K549). can I take out the wifi card from that mack and use that one for my mac air?Welcome to Apple Support Communities
Consider yourself lucky that your MacBook is still working. Now, turn it off. Wine may have damaged other parts of your computer.
Then, take the MacBook to an Apple Store or reseller. It will be a very expensive repair, as it's not covered by warranty and the logic board has to be replaced. In some cases, it may be better to get a new MacBook.
If you can't take it to an Apple Store, contact with Apple > http://support.apple.com/kb/HE57 -
New wifi card for PowerBook G4 (2002, OS 10.4.11)
Hello,
Can anyone recommend a wifi card for a PowerBook G4?
I've just bought a secondhand model, and I'd like to broaden its wifi capability. Being able to use WPA security would be a good start.
- RichardI bought the WiFi card from eBay. It's a Chinese clone of a Motorola WN825Gv3 (part number: 518565-001-00). Here's the old eBay link: http://bit.ly/XmW0Gb
I can't remember exactly what settings I used on my Powerbook – mainly because I clicked things at random until it worked – but I did have to click "renew lease" in WiFI settings to get the card to work.
I didn't have to change any settings on my router, but the card isn't compatible with 5Hz WiFi frequencies, or the "n" speed WiFi.
Other than having to renew the lease occasionally, the card works smoothly.
- Richard
Maybe you are looking for
-
Clean Windows 8.1 install on Split 13 x2
I have been unable to solve a Windows 8.1 boot failure on a customer's Split 13 x2. The system will boot from a Windows 8.1 recovery USB stick that I created. I can see the volumes on the disk and bcdedit seems to display the correct information bu
-
How to know the logged in username in BLS?
Hi MIIers i know i can use this session variable( ) in HTML to get the logged in user name. But how to get the logged in user name in BLS? Is it the same way ? ( I might be duplicate post but we have to bare with it..search results didn't get me pro
-
Is it possible to create an internal table in XI??
Hi Experts, My scenario is IDoc to JDBC. Some fields are direct mapping but where in my requirement is like this. Need to create one internal table with 6 fields. In this one field would be Counter and remaining are populated with the IDoc fields dat
-
hi all, i would like to know how to configure APP so that the company can make automatic payment to all vendor but not certain vendors based on the vendor number. I am at the learning stage so if there are scenario could you please bring it up with a
-
Find/Change throughout a book
I have several documents I'd like to use find/change with. Is there a way I can create a book of all these docs and use find/change? Is there perhaps a better way to do this? Any help would be appreciated! Thanks