Recommended spec can take how many concurrent users
With the following recommended spec from Adobe website, how many concurrent users ?
Flash Media Streaming Server system requirements
OS : Windows Server 2003 SP2 or Windows 2008
H/W Requirements
- 3.2GHz Intel Pentium 4 Processor (dual Intel Xeon or faster recommended)
- 2GB RAM ( 4GB recommended)
- 1Gb Ethernet card
Hi,
The number of concurrent users really depends on your setup.
You might want to read the blogpost from the FMS PM on this at: http://blogs.adobe.com/ktowes/2008/08/breaking_1gbps_on_flash_media.html
"I’ve received a lot of requests lately about how much media can be delivered through Flash Media Server (FMS). As you may or may not know, FMS is held to the same limitations as most other streaming or HTTP servers, that is the available bandwidth, disk speed, memory and CPU power on a single server. When we introduced Flash Media Server 3 we increased the performance significantly to allow you to take full advantage of hardware and ultimately help to reduce the total cost of ownership. ........... read on"
Greetz,
Klaasjan
Similar Messages
-
How many concurrent users on a FMS?
We want to stream live Town Hall meetings with the majority
of the users viewing it from our inTRAnet. 320x240, 30fps, Dual 2.8
GHz, 4 GB widows server. Anybody with similiar setup using FIMS to
service 200 or 500 concurrent users? We have two campuses and I
need to know if I will need to spec a second server if we get above
a certain number. How many concurrent users can I supprot with the
above configuration? ThanksFMS should be able to handle your 500 clients with no problem
using the configuration you mentioned (some of my apps routinely
see many times more than that on a similar server). I use a
slightly beefier processor in my boxes though... quad core
Kentsfield Xeon / 4GB ram.
That said, also make sure you have enough throughput at your
NIC to handle the traffic. At 500 concurrent clients, a low
bandwidth stream of 300kbps puts you at about 150Mbps, so you'll
want to run the numbers before you commit to a single serves in
case you can't get enough network juice to a single box. -
How to find out how many concurrent users using web application?
Hi all,
I have a web application deployed using 9iAS. I am trying to find out how to find out how many concurrent users are using this application at any one time. According to Oracle there is no way to see this information using the enterprise manager interface.
Does anybody out there know how I can find out this information in real time? Failing that, are there any good analysis tools out there that display usage to the minute (all the tools I have found show usage by hour which is not sufficent for my needs).
Any help would be much appreciated,
CarolineI know I haven't heard of any software to do this, but this also sounds like a really hard problem to try and really analyze well.
The trick is, you might "infer" how long a user is using an application based on when cookies are set and when they're set to expire. If that's a long time, though, that could count far more "concurrent" users than are actually there. A user could simply close the application at any time and stop using the application; you can't really detect that because the server isn't "told" when the user closes their browser or goes somewhere else.
A good perl script might be able to read the Apache access log and tell you how many unique IPs asked for a given directory in which various applications are stored in any 5 minute span of time... that could be something like an indicator of "concurrent" users.
If you don't know Perl, I'd suggest getting the O'Reilly & Associates book on Perl and learning it, because the more I think about this, the more this sounds like a textbook example for applying a Perl script. -
How many concurrent users are allowed for an Azure Virtual Machine?
How many concurrent users are allowed for an Azure Virtual Machine?
Please share the details with the Azure VM size. Currently I have Standard VM of size D13(4 cores, 28GB RAM)Hi SanPSK,
Thanks for posting here.
I suggest you to check this article for Azure VM size
https://msdn.microsoft.com/en-us/library/azure/dn197896.aspx
For the concurrent users on VM - A maximum of 2 concurrent connections are supported, unless the server is configured as a Remote Desktop Services session host.
Girish Prajwal -
How many concurrent users are allowed in 8.1.7
Hi All,
I need to find out how many users can log into a 8.1.7 database. Can anybody help me with this?
Its a 8.1.7 database running on Sun 5.9
Any help would be very appreciated.What Joel said is true but you may also need to set a couple of init.ora parameters for sessions, processes. Oracle provides a couple of parameters that can be used to limit connections: license_max_sessions, license_max_users, and license_sessions_warning.
See the Oracle 8.1.7 Reference manual for details on the parameters.
HTH -- Mark D Powell -- -
How do we find out how many concurrent users login at peak time?
Hi Frienz
PLease let me know if there is any database trigger that we can keep to monitor this?
Poonam SachdevaYou can also use audit features of the database to audit user connections/disconnections
and write the query to get what you need.
Or you can also use with 9i/10g a LOGON/LOGOFF trigger to audit session connection and disconnection in a audit table and then write the query on this audit table to analyze the maximum number of connections. -
How many concurrent connections that an ACS server version 4.2 latest patch can handle?
I have about 50 routers and layer-3 switches that autheticate via tacacs+. The AAA server used to be on a Linux machine running open-source tacacs+ built by me. I have a perl script that will log into all 50 devices at the same time to collect statistics. This script is multi-threaded. Everything is working fine so far.
I recently out-sourced the AAA function to a 3rd party company, not by my choice. The 3rd party uses Cisco ACS version 4.2 with the latest patch running on Windows 2003 Enterprise Server with 16GB RAM and quad processors with quad-cores, IBM x3650-M2 hardware. The connectivity between the 3rd party and my company is through a DS-3 connection. Maximum bandwidth over this DS-3 connection is less than 10Mbps at most.
I noticed that for the past 3 months I have multiple failures with this perl script due to authentication failure with the ACS server. If I just run the script again a few routers/switches, there are no issues; however, whenever I started the script to log into 50 devices all at the same time, it will fail. If I made the configuration on all routers/switches to point back to the old open-source tacacs+ server, the issue goes away. The minute I switched back to the
new ACS server, the issue came back. If I modified the script to hit one device at a time, it works fine. I think it is the ACS server can not handle a lot
of AAA requests at the same time.
Does anyone know how many concurrent connections that an ACS 4.2, with latest patches on Windows 2003 Enterprise Server with lot of memory and CPU power, can handle? I can't seem to find this anywhere on Cisco website.
Thanks in advance.No, Im not saying ACS cannot cope.
Concurrency and latency are very different things. ACS CSTacacs can handle many 100s of simple authentications/authorisations per second with users in the internal database. If 1000s of devices all send traffic in the same instant it would take some seconds to work through the backlog of traffic.
Also, worth considering that a limited number of tasks within ACS (or threads) can actually handle a much greater number of "logins" because they are generally multi-message allowing ACS to keep lots of plates spinning.
If users are in an external databases the latency (per authentication) can increase depending on where the users are (eg Windows AD) and if bad enough can have a serious effect on the overall authentication rate. At which point customers normally turn to load balancing.
If your device timeouts are 20 seconds (totally reasonable) I suggest the issue is more likely to be something else... a bug, perhaps specific to v4.2? -
ASA 5510 - how many concurrent VOIP calls can pass through?
Hi all,
I wonder how many concurrent VOIP calls can handle Cisco ASA 5510, any idea?
Geghamhi Gegham,
Basically what the values of 50,000 and 130000 connections indicate are lab values tested with 80% TCP and 20% udp traffic. (according to table a-2 in the doc below)
http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/specs.html#wp1170941
RTP is udp traffic but in case of an asa and considering a customer scenario what happens is...
1 voip call = 1 control connection (h323,sip,sccp) + 2 or 4 rtp connections
-so a call will in total easily consume 5 or more connections depending on control connections you have set up .
-also this number differs depending on if the call is voice only or video.
So to simply answer your questions...
1>the number of connections that a call consumes depends on the above factors.
2>Also there is no hard number on the number of calls an asa can handle because this depends on the controls you use ...including nat and inspections.
Thanks,
Karthik -
Parallel How many times user can login to the SAP system through ITS
Hello all
We are using the ITS ---620 and following 46D R/3 system
R/3 system details:
Kernal :
kernel release :46D
O/S :SunOS 5.8 Generic_108528-05 sun4us
We would like to now, At a time How many times user can login to the SAP system through ITS
Kindly letus know if any one have idea about parameter which can restrict the end users to u201CNu201D times/ sessions.
Transaction SITSPMON/SMICM are not working in R/3 system as it is 46D.
We found that parameter u201Clogin/disable_multi_gui_loginu201D works with SAPgui logons.
System logons using the Internet Transaction Server (ITS) or Remote Function Call (RFC) are not affected by this Parameter u201Clogin/disable_multi_gui_loginu201D
I need similar parameter u201Clogin/disable_multi_gui_loginu201D for the ITS users.
ThanksI have searched all docs and notes.
Everytime the answer is PArameter for multi_gui_logonis not applicable for SAP Gui for HTML ( Browser )
The functionality does not exist for SAP Gui for HTML.
Regards, -
How many concurrent connections can ACS handle at once?
Hi Experts,
Could you please let me know how many concurrent connections ACS can handle at once?
Is there any limitation on it?
Our ACS version is 4.0 (1) build 27.
Thanks in advance for your help and have a nice day!
Regards,
GaborIt depends on many other factors but as far as I know ACS can handle upto 40 Auth request per second*
*Condition Apply
Regards,
~JG
Do rate helpful posts -
How many concurrency request can handel in wcf
hi
i have a question :
wcf support how many concurrency request a time ?
for example i have a wcf service and a lot of (10000) client that call the wcf together
thanksI think all your clients will be able to use your WCF Service regardless of Concurrency.
I believe that concurrency is related to the threading of the individual request. Not completely sure about that part though. But, all your clients should be able to access the service regardless of the concurrency. That would be more based on the stress on
your server.
Developing is part of being a developer. -
How many concurrent admin sessions are supported on CiscoWorks LMS 3.2?
How many concurrent admin sessions are supported on CiscoWorks LMS 3.2?
We recommend having no more than 20 simultaneous users logged into LMS (for performance reasons). All of these users can be administrators. That said, there is no hard limit.
-
Find out how many remote users are login in to my system.
Hi
i just want to know how many no of remote users are logged in to my system and their information.
how can i restrict them. how to limit the remote connections.
how many ftp user's are connected to my system.
can any one send me documents which contain brief information for about questions.use rusers and finger commands to check the users remotely login
form limitint the access of user u need to create $HOME/hosts.equiv and $HOME/.rhosts and making entry for those users who u want to allow -
How many concurrent VPN client sessions available for cisco 2621XM?
I have cisco router 2621XM with IOS c2600-advipservicesk9-mz.124-11.T4.
I want to know, how many concurrent VPN client sessions can be available in this image.here is the configuration on PIX,
group-policy DfltGrpPolicy attributes
wins-server value 10.0.0.67 10.0.0.68
dns-server value 10.0.0.67 10.0.0.68
vpn-simultaneous-logins 20
vpn-idle-timeout 5
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn-acl
default-domain value mydomain.com
address-pools value vpnpool group-policy DfltGrpPolicy attributes
wins-server value 10.0.0.67 10.0.0.68
dns-server value 10.0.0.67 10.0.0.68
vpn-simultaneous-logins 20
vpn-idle-timeout 5
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn-acl
default-domain value want-want.com
address-pools value vpnpool -
How many Concurrent Requests handled in XI?
Hi,
Can anybody let me know how many concurrent requests can be handled in XI and where to check this number for a syncronous scenario ?
Thanks
SreenivasHi sreenivas,
it depends mainly on the number of work process available in your system and on the tuning of java vm.
Have a look at <a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/70ada5ef-0201-0010-1f8b-c935e444b0ad">SAP Exchange Infrastructure Tuning Guide XI 3.0</a>
Hope it helps,
best regards,
Sergio
Maybe you are looking for
-
Boot camp how to delete osx and merge partitions for windows 7?
Im installing windows 7 through boot camp but without a dvd. Im using a installer from my university. I can only install it on a partition becouse i dont have the disc. It is done over the network. I have tried deleting the mac osx partition in windo
-
hi to all i created a java program for validateing two date start date should be less than end date end date should be greater than start date and here is my code <code> package src; import java.io.BufferedReader; import java.io.InputStreamReader; im
-
HOWTO: use table column value as tag name in XMLElement (9iR2)
Hi, maybe what I'm trying to do simply does not work, but here is my sample: select XMLElement(DUMMY, DUMMY).getClobVal( ) as SAMPLE from DUAL; returns the following XML <DUMMY>X</DUMMY> But what I want to get is <X>X</X> because "X" is the value of
-
Question Mark on QT logo? Solution That worked
Ok, So I have a mac, Whilst surfing the net using Safari I kept getting the Question Mark on top of the QT Symbol. This is what worked for me: Go to "Home" folder (Not USER folder, But Root Folder) Go to "Library" Go to "Internet Plug-Ins" Go to "Dis
-
I cannot listen to online radio streaming, i cannot listen to online radio streaming
whenever i try to access fm radio stations online, there would be a dialogue box saying "missing plug ins".