Regarding audio drivers
I installed a Windows partition for the first time tonight, and installed the Realtek High Definition Audio driver.
I was a little disappointed with the quality of sound using this driver. Do I have any other options for my OS/Machine? (Windows 7 32-bit)
Thanks!
Hi MilkManJT
Try this HP document No Sound from Speakers it has a number of good troubleshooting steps including using the built-in Windows Troubleshooter. Here is the correct IDT High-Definition Audio driver. Give that link and the driver a try and if that doesn't work they are you looking at a hardware issue and I would recommend calling HP regarding a repair. You can reach HP Total Care at 1-800-474-6836 in North America or start here if you live outside of North America.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP
Similar Messages
-
Best way to update AC97 audio drivers?
Is the best way to update AC97 audio drivers = dl. from msi the latest drivers which are 5.10.00.5970 (A3.80) I currently have 5890. Then uninstalling old ones from add-remove programs then install newest ones. Since live update doesn't seem to get it done. Thanks
DenI agree with the package that is in Dr Stu's link, I downloaded that complete package which includes NVMixer for speaker setup and fine tuning your sound system.
Regards; Pop's -
After Upgrading my OS to 10.5.8 from 10.4.1 I am unable to run Garageband '08. When I try to play one of my old projects the following message appears:
! GARAGE BAND HAS DETECTED A POSSIBLE CONFLICT BETWEEN ONE OR MORE THIRD PARTY MIDI OR AUDIO DRIVERS. BE SURE TO INSTALL THE LATEST DRIVERS FOR ALL AUDIO AND MIDI EQUIPMENT.
Can someone please tell me what the latest drivers are and what is a reliable place to acquire them.
I did download and installed PACE drivers, which I believe allow you to open protected files.
Thank you.
RLThanks for the prompt reply Cristoph. That is exactly what I did. It turns out there were a few prior discussions
regarding this issue, all advocating for the same method: I went to the Library folder, took out both Digidesign drivers from the Audio Midi Folder created a new folder within the Library and dumped them into it.
Voilå!! Garage Band works again! Thank you. -
A few simple tips and questions. Neo2 system XP re-install, which audio drivers?
My questions:
I'm re-installing my XP Pro system because I have decided I don't want to go with a 2GB primary partition as my first partition. Here are my questions.
1) Should I update from 1.4 to BIOS 1.5 ?
2) Which audio drivers should I use? nVidia Driver package 4.57? Or the Realtek ALCXXX_73 from nVidia website? Last time I actually accidentally installed the 4.60 audio MCP driver from the nForce 4 standalone package 6.39, but alas the sound was fine. (perhaps a little strange seeing as how my Neo2 is nForce3 and the 4.60 was from the nForce4 package.
Which audio drivers should I install?
3) What is nVidia nTune, what can I do with it and should I bother with it?
4) Which Catalyst driver should I install? The 29.7 MB driver with Catalyst Control Center or the 23.1 MB driver with Control Panel. Whats the difference and should I care?
I'll be using MSI update, keeping the windows IDE drivers, I may use the "speedfan" program but no digicell and no corecenter.
thanx,
My tips, See below:
0) Do your first install with a minimum of hardware installed (add your PCI cards later)
1) Research here for the proper BIOS settings for stable first boot and system install.
-Disable Agressive Timings in BIOS
-Turn Off NV/ATI Speedup in hidden BIOS
2) Install XP and SP2
3) install video drivers
4) Install nVidia UDP 5.10 (preferably without audio) and don't install the nVidia IDE drivers, just keep the XP drivers. (Use the XP windows IDE drivers) I used the nVidia LAN and it worked fine.
5) Install Zone Alarm (or your prefered software firewall) and then hook up LAN, preferably behind a router
6) Windows update once you have internet working
7) Install AMD Athlon 64 processor driverv1.1.0.18
8) Install audio driversThanx 10-4 on that one. I edited my system install to reflect your idea by inserting Zone Alarm install BEFORE connecting to the internet. As an aside, I have a router which our PC's are connected to, so I'm reasonably safe for a few minutes
Also, I won't really be installing the ATI Catalyst drivers now, as I'm just using a Gforce2 GTS 32MB AGP for now and XP Pro installs perfectly adequate drivers. When I get my card back from ATI I'll install the Catalyst drivers then. I'd still like some advice on which driver to install when I do though
Anyone have any other tips in regards to my questions? -
Audio Drivers for hp pavilion zd 8460ea model for Windows XP
Hi ,
Somebody please help me find the audio drivers for the model zd 8460ea for Windows xp OS.
Regards
JijuHi, Jiju:
Does your sound device show up in the device manager with the exclamation mark?
If so, please click on it, then click on the details tab.
Post the top string of characters you see. That string indentifies the manufacturer of the device and the device model.
With that info, hopefully we can find the correct driver for it.
Paul -
LAPTOP VAIO SVT15112CSX audio drivers that work with windows 10
Upgraded to Windows 10 (7/31/2015) VAIO SVT15112CSX but the audio (sound qaulity) was horrible. After some trying I found that installing the Windows 8.0 audio drivers from the Sony Support area for the latop made the sound work great again. I installed the patch (1) then rebooted. After that installed the audio driver (2) (not sure if you have todo it that way, but it worked for me). Everything else appears to work fine so far. :-) Support area: http://esupport.sony.com/US/p/model-home.pl?mdl=SVT15112CXS&LOC=3#/downloadTab Files from win8.0 64 bit: (there are no audio files in win 8.1 64 bit area).Description of files:(1) File DescriptionAudio Driver Registry PatchRelease Date2/01/2013Version2012 10/15File Size1.00 MBDOWNLOADThis utility installs the originally shipped version of the Audio Driver Registry Patch. (2) File DescriptionRealtek® High Definition Audio DriverRelease Date1/03/2013Version6.0.1.6695File Size132.26 MBDOWNLOADThis utility will install the originally shipped version of the Realtek High Definition Audio driver.
Hi condor,
Welcome to Sony Community!
I believe the right model name of your unit is SVT15112CXS and not SVT15112CSX. Based on eSupport website, the drivers and software for Windows 10 will be released on November 2015. Those drivers are specifically made for Windows 8, but I am glad that it works well with Windows 10. You may stick with these and wait for the updated drivers once released and install on your laptop.
Thank you for posting your experience condor. You post might be very helpful to other users experiencing the same issue. I'll bookmark this thread for future reference.
Best regards,
Vincent
If my post answers your question, please mark it as "Accept as Solution"
-
My problems are:
No sound with Youtube or the laptop itself
SoundMax won't install either though I downloaded HDA audio drivers it requested.
Flash download stuffed up my SoundMax after factory reset.
I decided to do a factory reset after Youtube starting slowing down. After reset it (Youtube) kind of worked better
then the audio disappeared from the laptop. The drivers, SoundMax Audio was gone (greyed out).
I downloaded the Audio driver from Lenovo website for my X31 but SoundMax install wouldn't install because it kept saying HDA Audio drivers weren't installed.
I downloaded it from here:
http://support.lenovo.com/en_AU/research/hints-or-tips/detail.page?&DocID=HT072373
So I went to HP site to download HDA audio drivers, then the SoundMax Audio reappeared and I had sound on my computer.
HDA Audio drivers link at HP website (since Lenovo doesn't have it):
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?cc=US&lang=en&swItem...
When I downloaded latest Adobe Flash, the SoundMax Audio disappeared again. So at the moment I have Youtube video without sound (and Firefox keeps telling me to download Flash?)
No sound on IE as well.
Would appreciate your help. Thank you very much.
I'm using:
ThinkPad X31 (2673-QU6)
Based on 2673-N7G
Win XP Pro Service 3 with recent updates
Firefox (latest) with add-ons
Solved!
Go to Solution.You need to install the modem driver too.
http://support.lenovo.com/en_AU/research/hints-or-tips/detail.page?&DocID=HT072373
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft -
Compaq CQ60-615dx Windows 8 Audio Drivers
I need some help getting the Audio Drivers for Windows 8 for my Compaq CQ60-615dx. I have tried using the Windows 7 Drivers, and the Vista Drivers to no avail. Any help or suggestions would be appreciated!
Hi,
They are still working on this:
http://answers.microsoft.com/en-us/windows/forum/windows_cp-hardware/bug-conexant-high-definition-sm...
Regards.,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Vpceg25en audio drivers for windows 10
Hi After updating windows 10 pro my audio drivers are not woking I tried by update driver and troubleshoot but it didnt workout for me. Kindly help me
Hi srinivasgsn,
Thank you for considering Sony Community!
Your computer needs an updated Windows 10 audio driver. Unfortunately, Sony is still validating the updated drivers and software for Windows 10. Please visit this page for further information: http://www.sony-asia.com/microsite/support/win10/en/index.html
One of the users here, jshanholtz was able to resolve the audio issue on his unit by modifying the audio driver. You may check the steps he provided but we cannot give you the assurance that it will work without issues. You may try it at your own risk. https://community.sony.com/t5/VAIO-Windows-10/Windows-10-Audio-Problem-Fix/m-p/517373#M228
What we recommend is to wait for the updated driver for Windows 10. Your Vaio VPCEG25EN is an Asia-Pacific model and we do not have the drivers that support your laptop.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
Best regards,
Vincent
If my post answers your question, please mark it as "Accept as Solution"
-
X200 Vista 64Bit Audio Drivers
I let System Update attempt to update the Connexant audio drivers and it failed because the update that was available was not signed. 64Bit requires all signed drivers. Now I can't even get back to how the machine originally shipped as the driver available for download appears to have the same issue.
Pointers to where I can find the right driver?ChrisKinsman wrote:
Did you even read my post?
This isn't an issue with UAC. This isn't an issue with an ActiveX control and the authenticode prompt.
This is an issue with 64Bit Windows only loading signed drivers. Hvae you ever run a 64Bit OS?
EXCUSE ME?how do you expect to get an answer without reading your "COMPLETE" post? try following this method and the next time mind your language if you can!
go to cmd
2. Right-click on the shortcut and select Run as administrator
3. When the command window opens, type or paste the following and press ENTER:
Bcdedit.exe /set nointegritychecks ON
4. Reboot and then try installing the driver.
Message Edited by samavedam_vijay on 11-14-2008 08:44 PM
Message Edited by samavedam_vijay on 11-14-2008 08:45 PM
Message Edited by nonny on 11-14-2008 11:42 AM
Cheers and regards,
• » νιנαソѕαяα∂нι ѕαмανє∂αм ™ « •
●๋•کáŕádhí'ک díáŕý ツ
I am a volunteer here. I don't work for Lenovo -
A quick primer on audio drivers, devices, and latency
This information has come from Durin, Adobe staffer:
Hi everyone,
A common question that comes up in these forums over and over has to do with recording latency, audio drivers, and device formats. I'm going to provide a brief overview of the different types of devices, how they interface with the computer and Audition, and steps to maximize performance and minimize the latency inherent in computer audio.
First, a few definitions:
Monitoring: listening to existing audio while simultaneously recording new audio.
Sample: The value of each individual bit of audio digitized by the audio device. Typically, the audio device measures the incoming signal 44,100 or 48,000 times every second.
Buffer Size: The "bucket" where samples are placed before being passed to the destination. An audio application will collect a buffers-worth of samples before feeding it to the audio device for playback. An audio device will collect a buffers-worth of samples before feeding it to the audio device when recording. Buffers are typically measured in Samples (command values being 64, 128, 512, 1024, 2048...) or milliseconds which is simply a calculation based on the device sample rate and buffer size.
Latency: The time span that occurs between providing an input signal into an audio device (through a microphone, keyboard, guitar input, etc) and when each buffers-worth of that signal is provided to the audio application. It also refers to the other direction, where the output audio signal is sent from the audio application to the audio device for playback. When recording while monitoring, the overall perceived latency can often be double the device buffer size.
ASIO, MME, CoreAudio: These are audio driver models, which simply specify the manner in which an audio application and audio device communicate. Apple Mac systems use CoreAudio almost exclusively which provides for low buffer sizes and the ability to mix and match different devices (called an Aggregate Device.) MME and ASIO are mostly Windows-exclusive driver models, and provide different methods of communicating between application and device. MME drivers allow the operating system itself to act as a go-between and are generally slower as they rely upon higher buffer sizes and have to pass through multiple processes on the computer before being sent to the audio device. ASIO drivers provide an audio application direct communication with the hardware, bypassing the operating system. This allows for much lower latency while being limited in an applications ability to access multiple devices simultaneously, or share a device channel with another application.
Dropouts: Missing audio data as a result of being unable to process an audio stream fast enough to keep up with the buffer size. Generally, dropouts occur when an audio application cannot process effects and mix tracks together quickly enough to fill the device buffer, or when the audio device is trying to send audio data to the application more quickly than it can handle it. (Remember when Lucy and Ethel were working at the chocolate factory and the machine sped up to the point where they were dropping chocolates all over the place? Pretend the chocolates were samples, Lucy and Ethel were the audio application, and the chocolate machine is the audio device/driver, and you'll have a pretty good visualization of how this works.)
Typically, latency is not a problem if you're simply playing back existing audio (you might experience a very slight delay between pressing PLAY and when audio is heard through your speakers) or recording to disk without monitoring existing audio tracks since precise timing is not crucial in these conditions. However, when trying to play along with a drum track, or sing a harmony to an existing track, or overdub narration to a video, latency becomes a factor since our ears are far more sensitive to timing issues than our other senses. If a bass guitar track is not precisely aligned with the drums, it quickly sounds sloppy. Therefore, we need to attempt to reduce latency as much as possible for these situations. If we simply set our Buffer Size parameter as low as it will go, we're likely to experience dropouts - especially if we have some tracks configured with audio effects which require additional processing and contribute their own latency to the chain. Dropouts are annoying but not destructive during playback, but if dropouts occur on the recording stream, it means you're losing data and your recording will never sound right - the data is simply lost. Obviously, this is not good.
Latency under 40ms is generally considered within the range of reasonable for recording. Some folks can hear even this and it affects their ability to play, but most people find this unnoticeable or tolerable. We can calculate our approximate desired buffer size with this formula:
(Sample per second / 1000) * Desired Latency
So, if we are recording at 44,100 Hz and we are aiming for 20ms latency: 44100 / 1000 * 20 = 882 samples. Most audio devices do not allow arbitrary buffer sizes but offer an array of choices, so we would select the closest option. The device I'm using right now offers 512 and 1024 samples as the closest available buffer sizes, so I would select 512 first and see how this performs. If my session has a lot of tracks and/or several effects, I might need to bump this up to 1024 if I experience dropouts.
Now that we hopefully have a pretty firm understanding of what constitutes latency and under what circumstances it is undesirable, let's take a look at how we can reduce it for our needs. You may find that you continue to experience dropouts at a buffer size of 1024 but that raising it to larger options introduces too much latency for your needs. So we need to determine what we can do to reduce our overhead in order to have quality playback and recording at this buffer size.
Effects: A common cause of playback latency is the use of effects. As your audio stream passes through an effect, it takes time for the computer to perform the calculations to modify that signal. Each effect in a chain introduces its own amount of latency before the chunk of audio even reaches the point where the audio application passes it to the audio device and starts to fill up the buffer. Audition and other DAWs attempt to address this through "latency compensation" routines which introduce a bit more latency when you first press play as they process several seconds of audio ahead of time before beginning to stream those chunks to the audio driver. In some cases, however, the effects may be so intensive that the CPU simply isn't processing the math fast enough. With Audition, you can "freeze" or pre-render these tracks by clicking the small lightning bolt button visible in the Effects Rack with that track selected. This performs a background render of that track, which automatically updates if you make any changes to the track or effect parameters, so that instead of calculating all those changes on-the-fly, it simply needs to stream back a plain old audio file which requires much fewer system resources. You may also choose to disable certain effects, or temporarily replace them with alternatives which may not sound exactly like what you want for your final mix, but which adequately simulate the desired effect for the purpose of recording. (You might replace the CPU-intensive Full Reverb effect with the lightweight Studio Reverb effect, for example. Full Reverb effect is mathematically far more accurate and realistic, but Studio Reverb can provide that quick "body" you might want when monitoring vocals, for example.) You can also just disable the effects for a track or clip while recording, and turn them on later.
Device and Driver Options: Different devices may have wildly different performance at the same buffer size and with the same session. Audio devices designed primarily for gaming are less likely to perform well at low buffer sizes as those designed for music production, for example. Even if the hardware performs the same, the driver mode may be a source of latency. ASIO is almost always faster than MME, though many device manufacturers do not supply an ASIO driver. The use of third-party, device-agnostic drivers, such as ASIO4ALL (www.asio4all.com) allow you to wrap an MME-only device inside a faux-ASIO shell. The audio application believes it's speaking to an ASIO driver, and ASIO4ALL has been streamlined to work more quickly with the MME device, or even to allow you to use different inputs and outputs on separate devices which ASIO would otherwise prevent.
We also now see more USB microphone devices which are input-only audio devices that generally use a generic Windows driver and, with a few exceptions, rarely offer native ASIO support. USB microphones generally require a higher buffer size as they are primarily designed for recording in cases where monitoring is unimportant. When attempting to record via a USB microphone and monitor via a separate audio device, you're more likely to run into issues where the two devices are not synchronized or drift apart after some time. (The ugly secret of many device manufacturers is that they rarely operate at EXACTLY the sample rate specified. The difference between 44,100 and 44,118 Hz is negligible when listening to audio, but when trying to precisely synchronize to a track recorded AT 44,100, the difference adds up over time and what sounded in sync for the first minute will be wildly off-beat several minutes later.) You are almost always going to have better sync and performance with a standard microphone connected to the same device you're using for playback, and for serious recording, this is the best practice. If USB microphones are your only option, then I would recommend making certain you purchase a high-quality one and have an equally high-quality playback device. Attempt to match the buffer sizes and sample rates as closely as possible, and consider using a higher buffer size and correcting the latency post-recording. (One method of doing this is to have a click or clap at the beginning of your session and make sure this is recorded by your USB microphone. After you finish your recording, you can visually line up the click in the recorded track with the click in the original track by moving your clip backwards in the timeline. This is not the most efficient method, but this alignment is the reason you see the clapboards in behind-the-scenes filmmaking footage.)
Other Hardware: Other hardware in your computer plays a role in the ability to feed or store audio data quickly. CPUs are so fast, and with multiple cores, capable of spreading the load so often the bottleneck for good performance - especially at high sample rates - tends to be your hard drive or storage media. It is highly recommended that you configure your temporary files location, and session/recording location, to a physical drive that is NOT the same as you have your operating system installed. Audition and other DAWs have absolutely no control over what Windows or OS X may decide to do at any given time and if your antivirus software or system file indexer decides it's time to start churning away at your hard drive at the same time that you're recording your magnum opus, you raise the likelihood of losing some of that performance. (In fact, it's a good idea to disable all non-essential applications and internet connections while recording to reduce the likelihood of external interference.) If you're going to be recording multiple tracks at once, it's a good idea to purchase the fastest hard drive your budget allows. Most cheap drives spin around 5400 rpm, which is fine for general use cases but does not allow for the fast read, write, and seek operations the drive needs to do when recording and playing back from multiple files simultaneously. 7200 RPM drives perform much better, and even faster options are available. While fragmentation is less of a problem on OS X systems, you'll want to frequently defragment your drive on Windows frequently - this process realigns all the blocks of your files so they're grouped together. As you write and delete files, pieces of each tend to get placed in the first location that has room. This ends up creating lots of gaps or splitting files up all over the disk. The act of reading or writing to these spread out areas cause the operation to take significantly longer than it needs to and can contribute to glitches in playback or loss of data when recording.There is one point in the above that needed a little clarification, relating to USB mics:
_durin_ wrote:
If USB microphones are your only option, then I would recommend making certain you purchase a high-quality one and have an equally high-quality playback device.
If you are going to spend that much, then you'd be better off putting a little more money into an external device with a proper mic pre, and a little less money by not bothering with a USB mic at all, and just getting a 'normal' condensor mic. It's true to say that over the years, the USB mic class of recording device has caused more trouble than any other, regardless.
You should also be aware that if you find a USB mic offering ASIO support, then unless it's got a headphone socket on it as well then you aren't going to be able to monitor what you record if you use it in its native ASIO mode. This is because your computer can only cope with one ASIO device in the system - that's all the spec allows. What you can do with most ASIO hardware though is share multiple streams (if the device has multiple inputs and outputs) between different software.
Seriously, USB mics are more trouble than they're worth. -
MSI 785GM-E51 can't install audio drivers
Hey, I would be grateful if you could help me with this problem.
When I try to install the audio drivers of this mobo(785GM-E51), Windows 7 can't find them. It offers me another set of drivers - that of VIA's, but it should be Realtek's. Normally it wouldn't be a problem, but I have a an issue with front panel microphone jack(it's not working), so I want to install the proper drivers. I tried disabling auto-installing option of Windows 7, and then install the drivers that MSI offers officially , but still the computer acts as if I didn't install anything.
EDIT: It seems that I have a different motherboard - in the document I have(about the parts of PC), it says that the computer has MSI 785GM-E51, but now that I checked the informationa about motherboard in the Windows itself, it appaars that ASrock M3A770DE is in the case. So I guess the fact that I can't install the MSI's drivers is because of different mobo. I have no idea how this could've happened.>>Posting Guide<<
Why don't you open up a case and read the model? Is the computer secured with some sort of sticker that voids warranty if opened? -
Audio Drivers for an XP install of a dv7t-1200?
I had to reformat my laptop and since Vista is still a mediocre at best OS, I decided to switch back to XP. Unfortunately, it seems as though HP has no audio drivers for this operating system. Is there any known way to get audio working on a dv7t-1200 under windows XP? Thank you in advance
Have you tried driver in C:\swsetup\driver ?
Pavilion DV2922TX, XP-SP3 32bit, Intel T5750 2.0Ghz, Nvidia Geforce 8400M GS with 128MB, 4GB 667 DDR2, 250GB HDD -
HT5628 How to fix track pad and audio drivers if we install windows 8 on macbook pro??
Can anyone help me how to install track pad and audio drivers for my MBP if i install windows 8 on it?
Run Boot Camp Assistant and select the menu option to download the Windows Support software, Then start Windows and install the Windows Support software. Follow the Boot Camp instructions which detail how to download and install the drivers (Windows Support software).
-
Audio drivers for Compaq C770LA for Win XP Pro / integrated mic not working
Hello. I have downgraded a Compaq C770LA to Win XP Pro SP3. Almost everything seem works perfect, but I have tried several audio drivers and still can´t get to control or use the integrated mic which this notebook has. I can hear audio and even record, etc, but there is no way to use or get to the integrated mic and some of the volumen controls I was used to (as "Record whats been listened") are lost. Does anybody knows wheter I have to change the driver or if it´s going to be any difference if I install for example the smartaudio add-on? I tried HP but they replied they don´t provide drivers for notebook for Operating Systems other than the one they gave the notebook with.
Thanks in advance for any clue!Try XP downgrade guide, here
Your model is in Part 2.
Pavilion DV2922TX, XP-SP3 32bit, Intel T5750 2.0Ghz, Nvidia Geforce 8400M GS with 128MB, 4GB 667 DDR2, 250GB HDD
Maybe you are looking for
-
I have multiple devices used by family members, how do you make sure the kids don't see Moms messages from Dad and visa versa?
-
Oracle 11.2 installation on solaries 64bit
Hi I am try to install oracle 11.2 on laptop with solaries 10(64bit) vmware meachine and my laptop os is XP 32 bit. But every time i run runinstaller it give errors.I am installing oracle 11g on 64bit because oracle 11g is not avaliable for 32bit os.
-
I've bought MacBook Pro a year ago. I needed to reinstall the mac so I did it. Than I realized that there is no DVD with iLife in my MacBook box. How can I instal it now?
-
Strange appearing midi Regions
I recently had a couple of midi regions change color from green to white or gray, without me adjusting any settings. I didn't pay attention to when or why it happened, because I thought I'd figure it out as I worked along- then when logic crashed lat
-
Can u mark messages as "read" in iPhone after reading them in apple mail?
As the title says. I'd like to find a way to have all my emails marked as "read" in my iphone mail after I've read them in my apple mail or vice versa. I belong to an email mailing list that I receive about 30 emails every day on that I'd like to not