Regarding File to Idoc Scenario

Dear Friends,
I am performing File to Idoc Scenario in XI 3.0. Here I got struck, I am not able to see my sender file in SXMB_IFR. It is saying that no messages availabe for selection. The file was picked up successfully from the souce. Please help me.
Thanks in advance.

check the error/ warning message that would be available at the end of the page (in RWB....where you see th yellow triangle)......even my IE is showing a yellow triangle but none of my interfaces are facing a problem.....just check for the status of the Communication channel in AE.....since your message is not transferred to SXMB_MONI confirm that the channel log is showing successful.....also can you tell what is teh status of other interfaces?.....are they running fine?...if yes then there seems to be problem with the sender channel......are you using any FCC?
One such situation where IE is showing yellow status is mentioned here: RWB Integration Engine status yellow
Just one doubt to ask...are you using the required Sender channel in the Sender Agreement?...hope there is no mismatch here....
Regards,
Abhishek.
Edited by: abhishek salvi on Jul 14, 2009 11:38 AM

Similar Messages

Query Regarding File to IDOC Scenario (1:2)

Hi,
I am working on a scenario like One File to Two IDOC's . In file we are getting some business functions (It's One feild in source file) , Some Business functions I need to map with One IDOC and some with other Idoc.
So I need to route a file content to two different Idoc's at a time.
I know this we can achieve this by using standard functions but not aware what to use.
So could anyone guide me how to achieve this..

Hi Saydulu,
>>n file we are getting some business functions (It's One feild in source file) , Some Business functions I need to map with One IDOC and some with other Idoc.
So you know which fields to map to idocA and whih to IdocB
Now to configure this...
1. create a Message Mapping
Add source as the message type which you created for file and target as the IDocs which you want to use .. Make sure you add them in the signature tab of message mapping. Here I will suggest to change the occurence of IDoc node befotre adding it to message mapping signature tab.. By default it is 1..1. To change the occurence download the XSD of Idoc and change the minoccur to 0 and maxoccurs to unbounded. This shopuld be done for both the Idocs.
2. Create a interface mapping with the source message interface (or service interface) and target Idoc names. No need to create any service interface for Idoc, you can use the same Idocs (that is imported from SAP)
3. Use this in interface determination of Integration Directory
Regards
suraj

Regarding RFC connection in File to IDOC Scenario

Hi everyone,
I was configuring file to Idoc Scenario, i have made all the required configurations in SLD, IR and ID, in XI system and in R/3 System. i have created RFC connection from XI to R/3 system, and its working fine. i have created an Partner profile in WE20 with sender file system name with inbound parameters. But still i am getting error as EDI Partner Profile not defined in WE05- iDOC ADDED WITH ERRORS. Do we need to create an RFC connection from R/3 system to XI for file to Idoc Scenario
!!! Note: RFC connection from R/3 system to XI is not working, will this be a problem for file to idoc scenario. !!!
Regards,
Varun Reddy.K

Hi Varun
Follow these steps
First - Maintain the Sender R/3 System:
SM59 : Create a RFC destination to XI
WE21 : Create a TRFC Port ->Specify the RFC Destination Created
BD54 : Create a Logical System for the Idoc Receiver
WE20 : Create Partner Profile ->Maintain Outbound and the Inbound Parameters
Second - Log on to XI System:
SM59 : RFC Destination for Sender System
IDX1 : Create the port to get Idoc Metadata from Sender System ( The Port Name must match the port name in the idoc header - Usually in format SAP<System ID>. eg. SAPID1 [Optional Step. Not mandatory]
IDX2 : Maintain the Idoc Metadata. This is needed only by XI, and not by other SAP systems. IDX2 is needed because XI needs to construct IDoc-XML from the IDoc. No other SAP system needs to do that.
Regards,
Santosh

Regarding error in XI File to IDoc scenario

Hi,
when i was doing file 2 idoc scenario i got this error "Unable to convert sender service to an ALE logical system". please resolve my issue as early as possible.

Uday,
Please go through these threads:
Unable to convert the sender service to an ALE logical system
How to convert Sender Party/Service to a Logical System?
Unable to convert the sender service to an ALE logical system
BR,
Alok
Edited by: Alok Sharma on Jan 31, 2008 12:39 PM

XI 3 File to IDoc scenario - Still referencing Old Logical system

Hi
Dont know if you can help. I have a file to idoc scenario using XI 3 to R/3 4.6c system.
I had the interface working from a third party system XMLHUB to SAP R/3. The Logical system name for the XMLHUB was XMLHUB01 in the SLD which I have set up as a partner profile in R/3. I have recently changed the logical system name to XMLHUBDEV01 in the SLD and created that logical system in R/3 and changed the partner profile to XMLHUBDEV01.
Unfortunately in the sender information of the IDoc the partner number is still XMLHUB01 and not XMLHUBDEV01. I don't understand where this partner is sent from to get into the control record of the IDoc.
I have cleared the SLD cache in both the Repository and the directory. Is there somewhere else I should be looking? Any help would be appreciated.
Regards
Daniel

hi daniel...
this thread wud answer ur query....
Re: IDOC Payload
regards..
vishal

Message has error status at outbound side File To Idoc Scenario

hi ,
In my File to Idoc scenario , when i go to sxmb_moni , i found that its showing red flag at Outbound Status Tab and showing message "Message has error status at outbound side".
When i go to IDX5 and and select my idoc and click on Transaction Id it shows "Password logon no longer possible - too many faile" .
Please suggest what may be the problem ?
Regards,
Rohit

1. First check the RFC destination name used in receiver Idoc adapter communication channel.
2. As i said earlier, in sm59 transaction in XI gui, u can check same rfc destination under type 3. There check the logon credentials and the username.
3. Now goto the R3 system GUI and check in su01 that same user is locked or not. If locked unlock it.
4. And if u change the password of that user, then do the similar change in XI -> sm59 -> rfc destination logon credential
Regards,
Prateek

Error in File to IDOC Scenario

Hi,
I have File to IDOC scenario.
I am getting error in sender file channel.
"Conversion initialization failed: java.lang.Exception: java.lang.Exception: java.lang.Exception: Error(s) in XML conversion parameters found: Mandatory parameter 'xml.keyfieldName': no value found "
Although I have used this parameter in content conversion 'xml.keyfieldName' (for each sub structure and defined a key field).
Despite of this error in sender channel I am receiving the message in XI.
But in XI also it throws error :
"Unable to convert the sender service PG_TOM_CEEMEA_RU_SFA to an ALE logical system"
Any help on this ?
Thanks,
Vikas

Hello Vikas,
I am getting error in sender file channel.
"Conversion initialization failed: java.lang.Exception: java.lang.Exception: java.lang.Exception: Error(s) in XML conversion parameters found: Mandatory parameter 'xml.keyfieldName': no value found "
Although I have used this parameter in content conversion 'xml.keyfieldName' (for each sub structure and defined a key field).
Check your flat file structure whether the key field you have chosen is appropriate and also recheck the FCC details whether you have assigned the value for the key field i.e. keyFieldValue.
"Unable to convert the sender service PG_TOM_CEEMEA_RU_SFA to an ALE logical system"
regarding the above error refer this
https://wiki.sdn.sap.com/wiki/display/XI/Unable%20to%20convert%20Sender%20system%20to%20ALE%20logical%20system
Regards,
Prasanna

Error while doing a File to IDOC scenario

Hi Experts,
I have created a File to IDOC scenario where in i have sent a file which has to pass data to ABSEN1 IDOC.I could see the IDOC reaching R/3 ,but with the status 56: "EDI: Partner profile inbound not available"
I have checked with all the configurations and couldnt find where it went wrong.
Kindly help me in this regard.
Thanks.

Hi
Check the inbound parameter and the process code.
To find Process code for IDoc use Tcode WE42.
ALE idoc trouble shooting use
Troubleshooting of ALE Process
look also this configuration
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/6bd6f69a-0701-0010-a88b-adbb6ee89b34

How to handle the control records in case of file to idoc scenario.

Hi All,
can you please clarify me how to handle the control records in case of file to idoc scenario.

Hi,
In File to Idoc scenario even though you selected apply control record values from payload and you are not getting those correct values which you have provided in the mapping.
Also check the checkboxes Take sender from payload and Take receiver from payload along with the Apply control record values from payload checkbox
Regards
Seshagiri

Reg:file to idoc scenario

In a file-xi-idoc scenario i created a business service for legacy
system and a business system for R/3 receiver system
i didn't assign logical system for the sender business service
and assigned a logical system for the reciver business system
so while maintaining partner profile in the R/3 system
i have to give partner no:
partner type:
here the problem is my sender business service i didn't assign any logical system,and it is not of LS type
so then what do i need to give in the above two fields?
answers required briefly

Hello,
you know this pdf:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/c09b775e-e56e-2910-1187-d8eba09c7a4a
Could be helpful.
Regards
Patrick

Partner Profile for file to IDOC scenario

Hi experts,
I am doing file to Idoc scenario. I did the ALE configuration steps between XI and r/3. For sender (ThirdParty) system, I defined Business system. While defining partner profiles in WE20 I got confused, whether to Give XI logical system Name or Third party logical system name. Please clarify..........
Thanks
Manoj

Hi,
>>I defined Business system. While defining partner profiles in WE20 I got confused, whether to Give XI logical system Name or Third party logical system name. Please clarify..........
in most cases you will only use one logical system in WE20
this will be XI's logical system - and you can route all the traffic
via this logicail system - this is the most popular case
for more about IDOCs and XI have a look at my book:
Mastering IDoc Business Scenarios with the SAP XI
http://www.sap-press.com/product.cfm?account=&product=H1935
Regards,
Michal Krawczyk
http://mypigenie.com - XI/PI FAQ

Alert Configuration for File to IDoc scenario

I have followed Alerts : Step-by-Step /people/michal.krawczyk2/blog/2005/06/28/xipi-faq-frequently-asked-questions
and configured Alerts for file to IDoc scenario.
But the problem is, I did not notice any alerts being generated. I could notice the IDocs being posted to destination system. So I was going through Alerts-Troubleshoute Guide. In intension to maintain monitoring level, I clicked Configuration tab. But I did not notice my sender and receiver system there to maintain.
Can any body help me to detail out the procedure to add sender and receiver systems to maintain the monitoring level?
Regards,
Suraj Kumar

hi Suraj,
WHich SP version are you on??
If you are on Sp14 or above, then unfortunately, Michal's Trouble Shooting for Alerts will not help.
From SP14 onwards, activation of end to end monitoring is not needed for Alerting. Refer to this note 870232 for this info.
Next, to test if your Alerts have been defined correctly, go to SE38. In the program , type RSALERTTEST and then click on EXECUTE button ( F8 ). In the next window, it will ask you for your ALERTCATEGORY. Just give the name of your ALERT CATEGORY and click EXECUTE.
If you have configured your alerts correctly, you will receive a message that tells ALERT IS GENERATED and will give the ALERT ID.
Now, go to your Run TIme workbench and then select ALERT INBOX and see if you have got the ALERT message in your ALERT INBOX.
If this is working fine, then the last step, implement the note 913858.
Regards,
Bhavesh

IDocs not created in file to IDoc scenario

Hi all
I am trying this file to IDoc scenario.
File picked up successfully and sent to R/3 BackendBut Idoc is not postedthe status records
In /n we05 in R/3 Backend shows that EDI: Partner profile inbound not available
I created/tested all basics like RFC dest, port etc.
File service that I am using is a business service hence I am specifying a Logical system name in
Adapter specific Identifiers of the file service.
I disabled EDI_DC40 control tag record as IDoc adapter
takes care of it.
So at first I tried the configuration of IDoc comm. Channel by checking the Apply control record values from payload
But SXMB monitor gave an error regarding this control record tagI guess as we have disabled it so there wont be any values
for control record in payload (correct me if I am wrong).
So I unchecked the checkbox Apply control record values from payload and monitor showed up as successfully processed.
But in the backend I am getting this error regarding partner profile.
I also tried to use an existing profile (LS type) by modifying its inbound parameters to accept CREMAS Idoc.
But the error is as persistent as me
Pls help
Sudhir

Hi
Sender --> LEGACY, maintained in SLD (Logical system).
Receiver--> ENI maintained in SLD with logical sys name M700.
Partner Profile LEGACY maintained in R3.
Following is the IDocOutbound in SXMB monitor in XI.
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:IDocOutbound xmlns:SAP="http://sap.com/xi/XI/Message/30">
<SAP:TABNAM>EDI_DC40</SAP:TABNAM>
<SAP:MANDT>100</SAP:MANDT>
<SAP:DOCREL>640</SAP:DOCREL>
<SAP:DOCNUM>0000000000001013</SAP:DOCNUM>
<SAP:DIRECT>2</SAP:DIRECT>
<SAP:IDOCTYP>CREMAS03</SAP:IDOCTYP>
<SAP:CIMTYP />
<SAP:MESTYP>CREMAS</SAP:MESTYP>
<SAP:MESCOD />
<SAP:MESFCT />
<SAP:SNDPOR>SAPAXI</SAP:SNDPOR>
<SAP:SNDPRN>LEGACY</SAP:SNDPRN>
<SAP:SNDPRT>LS</SAP:SNDPRT>
<SAP:SNDPFC />
<SAP:RCVPOR>SAPENI</SAP:RCVPOR>
<SAP:RCVPRN>M700</SAP:RCVPRN>
<SAP:RCVPRT>LS</SAP:RCVPRT>
<SAP:RCVPFC />
<SAP:TEST />
<SAP:SERIAL />
<SAP:EXPRSS />
<SAP:STD />
<SAP:STDVRS />
<SAP:STATUS />
<SAP:OUTMOD />
<SAP:SNDSAD />
<SAP:SNDLAD />
<SAP:RCVSAD />
<SAP:RCVLAD />
<SAP:STDMES />
<SAP:REFINT />
<SAP:REFGRP />
<SAP:REFMES />
<SAP:CREDAT>0000-00-00</SAP:CREDAT>
<SAP:CRETIM>00:00:00</SAP:CRETIM>
<SAP:ARCKEY>DF57A2C0532811D9AD84000F206A031B</SAP:ARCKEY>
</SAP:IDocOutbound>
Control record of IDoc in R3
Tab: Typeinfo
 Basic type-->CREMAS03
 Message Type-->CREMAS
Tab: Partner
 Recipient
 Port -->SAPENI
 Partner Number--> M700
 Partner Type-->LS
 Sender
 Port -->SAPAXI
 Partner Number--> LEGACY
 Partner Type-->LS
Pls help
Regards
Sudhir

ALE Configurations in File to IDOC Scenario

Hi All,
We are doing File to IDOC Scenario.
ALE Configurations done:
R/3 Side:
1. Created RFC dest, pointing to XI and tested the connection for remote login to XI.
2. Created port in R/3(using automatically generated port name) and assigned the RFC dest created above.
3. Created partner profile and assigned the ports to the message types.
4. Created Logical system
XI side:
1. Created RFC dest, pointing to XI and tested the connection for remote login to r/3.
2. Created port using IDX1 transaction with port name starting with SAP<SID> and assigned the RFC dest created above. (SID of XI)
3. Unable to load metadata in XI.
Now we are unable to test the scenario as it provides an error message in MONI as "Error: Transaction IDX1: Port SAP<SID>, client , RFC destination contain errors".
Also Let me know whether the steps mentioned above are correct for the scenario.
Regards,
Nithiyanandam

Hello,
SAP XI
1) RFC Destination (SM59)
a) Choose create.
b) Specify the name of the RFC destination
c) Select connection type as 3 and save
d) In the technical settings tab enter the details SAP SID/URL and system number#.
e) Enter the Gateway host as same details above SID/URL.
f) Gateway service is 3300+system number#.
g) In the Logon /Security tab, enter the client user & Password details of Destination system.
h) Test the connection and remote logon.
2) Create Port (IDX1)
a) Select create new button
b) Enter the port name as SAP+SID (The starting char should be SAP)
c) Enter the destination client.
d) Enter the RFC Destination created in SAP XI towards other system.
e) Save
3) Load Meta Data for IDOC (IDX2) a) Create new
b) IDOC Message Type
c) Enter port created in IDX1.
SAP R/3
1) RFC Destination (SM59)
a) Choose create.
b) Specify the name of the RFC destination
c) Select connection type as 3 and save
d) In the technical settings tab enter the details SAP SID/URL and system number#.
e) Enter the Gateway host as same details above SID/URL.
f) Gateway service is #####+system number#.
g) In the Logon /Security tab, enter the client user & Password details of Destination system.
h) Test the connection and remote logon.
2) Create Port (We21)
a) First Select Transactional RFC and then click create button
b) Enter the destination port name as SAP+SID (The starting char should be SAP)
c) Enter the destination client.
d) Enter the RFC Destination created in SAP R/3 towards other system.
e) Save
3) Create Partner Profile (WE20)
a) Create New
b) Create the Partner no. name as same the logical system name of the destination system.
c) Select Partner type LS
d) Enter details for Type: US/USER, Agent, and Lang.
e) Click on the + button to select the message type.
f) Select Partner no. and LS which ever create above.
g) Select Message type
h) Select Process code related to the Message type.
I) save.
In SLD System Landscape Directory
TS for R/3 (Logical system):-Assign the client name created in R/3 as Logical system Name.
Ts for Third Party (Logical system):-
BS for SAP R/3 (Logical system):- Assign the client name created in R/3 as Logical system Name.
BS for Third Party (Logical system):-Enter the XI logical system name.
With Regards,
Vidya.
*******Reward with Points if found useful

Steps required in File to Idoc Scenario

Hey guys i m doin a file to Idoc scenario and just wanna make sure my steps r correct.
steps done on the XI server
1.Create RFC destination(test the destination by giving the target host as the R/3 server).
2.Create port for the RFC destination.
steps on the R/3 side
1.Create/verify logical system name.
and finally create business system for this logical system in SLD.
now do i need to do partner profile as well or not? and if i have to do it how is it accomplished.
thanx
ahmad

Hi,
The following are needed for idoc to file scenario...
In R3...
RFC dest to XI (sm59)
Logical system (bd54)
Port to XI (we21)
Partner profile for the logical system (we20)
In XI...
RFC dest to R3 (sm59)
Port to R3 (idx1)
create metadata for the idoc (idx2)
In sld...
create business system for R3.
Regards,
Uma

Regarding File to Idoc Scenario

Similar Messages

Maybe you are looking for