Remote Desktop Connection to VM does not work after sysprep

Hello altogether.
Often asked, but never answered with an applicable solution!
What shall
we
do if
we
get no access to a Azure VM via Remote Desktop
Connection?
Everything went well: access to the VM via RDC was working perfectly!
Then
the idea came into
our
mind to create an image of the VM by use of the Azure Management Portal.
We
found that
we
had to apply “sysprep”
on the VM.
We
did it.
Then we did not take the image and decided to go on with the VM.
But if we start the VM we get no access via RDC!
We tried to find a solution by reviewing the already published contributions by other Azure
users. But none of the replies marked as answered supply with a qualified solution.
So can one provide a really applicable solution to us on how to arrange the further use of the VM?
Thank you in advance.

There is an issue right now where the VM may start unexpectedly after you have run sysprep and selected the shutdown option (which is normally what you should do).
http://social.msdn.microsoft.com/Forums/windowsazure/en-US/fafb9ee6-1e57-46ba-8440-27467ad986cf/image-capture-issue-vm-unexpectedly-started-after-guestinitiated-shutdown?forum=WAVirtualMachinesforWindows
But regardless of that issue - you can't use that deployed instance of the VM after you've run sysprep on it. It needs to stay shutdown, then you select Capture to create an image from it.
If you start it back up, either intentionally, or it is started unexpectedly because of the issue above, it will be sitting at the first interactive screen of setup. RDP is not working at that point, and since there is no console access to an Azure VM, there
is no way to get past that prompt.
For other scenarios, you might be able to attach the OS disk of that VM as a data disk to another VM, and while you could do that in this case too, there is no supported method for disabling sysprep at that stage of setup.
So while you could attach it to another VM to get data off of it (you would have to remove the VM first), the VHD is no longer in a supported state to use as a VM itself.
Thanks,
Craig

Similar Messages

  • Microsoft Remote Desktop Connection Client for Mac Not Working

    I recently purchased Office 2011 for Mac.  I work at home on my Mac at work on Windows 7.  I also have a work laptop, running Windows 7, that comes home with me.  My goal is to RDC my Mac to the laptop running Windows 7 to reduce desktop clutter, and easily work between machines. 
    I CAN NOT FIGURE OUT how to get Microsoft RDC:mac to connect to my pc. 
    I know that the pc allows remote desktop connections because I often use RDC at work from PC to PC.
    SOME PLEASE HELP!  I have spent hours and hours trying to figure this out and I think it is the time capsule that is causing the problem. 
    My research has found that I have to use port 3389 to get this done.  I am pretty computer savy but when it comes to networking I guess I have no clue.  I have tried just about everything a and can't figure it out. 
    Thanks to anyone that can dedicate some time to configureing my time capsule to allow for RDC.

    I cannot quite put together your whole network..
    I work at home on my Mac at work on Windows 7.  I also have a work laptop, running Windows 7, that comes home with me.  My goal is to RDC my Mac to the laptop running Windows 7 to reduce desktop clutter, and easily work between machines.   
    So this is in local lan.. the PC laptop running win7 and the Mac loaded with RDC software. If this is local lan then the issue is nothing to do with TC.
    That is only if you are trying to connect from work. to home through the router at work and TC at home. On local lan there is no blocking to ports. Are you using the local network IP of the PC Laptop?
    Explain a bit further as it needs a bit more clarification.

  • The Remote Desktop Connection Broker server could not enumerate the targets for the provider named NULL from the database.

    When I try to install Connection Broker on a Windows 2012 R2 Server in a Windows 2003 domain I get this error:
    The Remote Desktop Connection Broker server could not enumerate the targets for the provider named NULL from the database.
    Pooled virtual desktop collection name: NULL
    Error: Logon to the database failed.
    I have added both the Connection Broker server and the 2 remote desktop servers (also Windows 2012 R2 Servers) to the "Windows Authorization Access Group" in the domain according to this: http://support.microsoft.com/kb/331951
    But it still does not work :-(
    I keep getting same error....
    Any idea what I might be missing ?

    Hi,
    Thank you for posting in Windows Server Forum.
    Firstly please let us know by which method you have setup RDS role. You can have more advantage and feature when you will install with Standard deployment instead of Quick start deployment. So if you have setup with quick start option then you can try installing
    with standard type and check the result.
    In addition, please check SQL server database is properly configured for RDS server. Also check that domain controller properly communicates. Kindly go through below thread for more information.
    Server 2012 RDS - Remote
    Desktop Connection Broker Client failed to redirect the user domain\username. Error: NULL
    Hope it helps!
    Thanks.
    Dharmesh Solanki

  • Intermittently iphone 6 and 6 plus is wifi connected but internet does not work.

    Hi,
    I have an issue where intermittently iphone 6 and 6 plus is wifi connected but internet does not work. iMessage works though.  Toggling the wifi setting clears
    the issue temporarily but it occurs again.  Running iOS 8.3 now.  This was the case on iOS 8.1 and 8.2 as well. 
    I have tried the typical troubleshooting steps (reboot/reset network settings/disabling location services for wifi/upgrade/etc)
    My router is an EA9200 router with 2.4 Ghz and 5 Ghz.  It is configured with all bands with the same name.
    All other devices in my house works perfectly fine and has no disconnects (ipad/macbook air/tv's/receivers)
    My thought is that iphone 6 cannot handle well the moving around between bands. 
    Any thoughts or suggestions would be greatly appreciated.
    Thanks,
    David

    Have you tried to reboot your router by turning off the power (you may have to unplug it from the power source), then waiting about 30 seconds, then turning it back on?  This seems to solve a lot of problems.

  • TS3367 Hi, the FaceTime just did not work between my mom and I. It used to work weeks ago, but now it does not work after showing"connecting". I feel frustrated and try all the method I can think of. Still do not work. Hope u can help me. Thanks!

    Hi, the FaceTime just did not work between my mom and I. It used to work weeks ago, but now it does not work after showing"connecting". I feel frustrated and try all the method I can think of. Still do not work. Hope u can help me. Thanks!

    Was it just this one time?  Could be that you, or your mom, were experiencing network problems.  Try again at a later time.

  • My sound system does not work AFTER installing pc to tv wireless connection

    my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

    Hi,
    You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
    Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
    one used by the Form contact for Form Invoice.
    Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
    VS General Question forum mainly discusses
    the usage of Visual Studio IDE such as
    WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
    System and Visual Studio Editor.
    Thanks,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • "F11 System Recovery" during boot does not work after Cloning hard drive.

    Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
    HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
    Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
    Startup Menu (F11 System Menu works properly) only on original hard drive.
    Following obtained from Disk Management & diskpart in Command Prompt.
                                     GPT Disk <700GB>
    Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
    Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
    Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
    Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
    Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
    Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
    Partition 7 NTFS Primary 26MB/350MB [Recovery]
    Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
    I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
    Acronis True Image 2015
    Acronis Backup for PC
    AOMEI Backupper Professional
    Macrium Reflect
    Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
    “Recovery
    Your PC needs to be repaired
    A required device isn’t connected or can’t be accessed.
    Error code: 0xc0000225
    You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
    Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
    Thank you in advanced.

    Hi,
    How did you clone the HDD ? One-for-one or different method ?
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Continuous with the problem, the headphone does not work after having my iphone ios 8.0.2 updated

    the headset does not work after having my iphone ios 8.0.2 updated to me is very annoying to have to be answering speakerphone is not private and can not go with the hands-free all the time

    I had the same issue until I updated my apps through iTunes. I had over 100 updates, but none of them showed on my iPod. After they updated everything started syncing like it is supposed. Go to the apps library and check for updates. After everything syncs leave your iPhone/ipod/ipad connected if the spinning arrows at the top is still spinning. It means that things are still being added. If you go to settings > general > about, you will see it loading songs, videos, photos, etc. If you back out of "about" and then go back to it you will see the numbers for each one change.

  • RDP does not work after disabling TLS 1.0

    RDP does not work after disabling TLS 1.0
    Had to re-enable it .... what can i do to make it work with TLS 1.2 ??

    Hi,
    Disabling TLS 1.0 will break RDP under default settings.  Did the security scan say specifically to disable TLS 1.0?  Normally you should be able to disable use of certain ciphers or prioritize ciphers.  You may want to try IISCrypto, on
    it you click the PCI button, then Apply button, then restart your server.
    Additionally there are still a substantial number of web browsers in use that do not support TLS 1.1/1.2.
    If you would like to continue with TLS 1.0 disabled you may change the RDP Security Layer.  To do this please open Terminal Services Configuration (tsconfig.msc), double-click RDP-Tcp, change Security Layer to RDP Security Layer.
    IMPORTANT:  You are vulnerable to MITM attack when using RDP Security Layer because there is no Server Authentication.  If you are running RDP over a VPN connection and there is no risk for interception then this may be okay.  I recommend
    you re-enable TLS 1.0 and have a ssl certificate from a public authority set on your RDP-Tcp listener.
    Quoted from this thread answered
    by TP, for more information you can go through that thread. 
    Hope it helps!
    Thanks.
    Dharmesh Solanki
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Satellite A110-228 LAN does not work after hibernate

    Well, subject says it all, really. The LAN (wired) network does not work after hibernate.
    It seems it cannot find the DHCP server, so after a while it gets a 169.* address.
    After a reboot, the network functions as usual (gets a IP address from the DHCP server)
    Tried the usual things, disconnecting the cable, disabling the LAN device, battery or AC adapter, the behavior is reproducible.
    The wireless network will be restored after a hibernate.
    It needs a little help though (right click on the icon and "recover" or whatever it is called in English)
    Any suggestions?
    Wilm Boerhout

    Hi guys
    In the Toshiba HW setup which is placed in the control panel the options Wake-up on LAN and Built-in LAN should be enabled.
    I think the options are disabled by default.
    Furthermore the default setting for Wake on Settings is OS controlled. To use the Wake-up on LAN function under power off mode, in the device driver for the network card under the menu point Wake On Settings the Value Wake on Magic & Directed must be set.
    Please check this how to enable WOL (first time use):
    1. Go to [Start] -> [Control Panel] -> [Toshiba HWSetup] -> [LAN] tab
    2. Enable Wake-up on LAN
    3. Click [Apply]. System will request to reboot.
    4. After the reboot go to [Start] -> [Control Panel] -> select [System]
    5. On system properties dialog box select [Hardware] tab -> click [Device manager]
    6. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
    7. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
    8. Press [OK] to close the dialog box.

  • Card slot does not work after update (14/10/2011)

    Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
    MacBook Pro 13 OS ver. 10.6.8

    Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

  • HT1688 My Hot Spot does not work after update to 6.0.1.  Service is with ATT.  Apple says problem is with ATT, ATT says problem is with Apple.  Anyone else having this problem?

    My Hot Spot does not work after update to 6.0.1.  Any suggestions?

    Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
    so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
    so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal.

  • Click to activate does not work after update

    Click to activate plugin does not work after updating to version 23.0.1

    hello Kamullia, if you have set click-to-play to true in about:config you can now go to the ''addons-manager > plugins'' section and set the permissions individually for each plugin type.

  • WiFi iPhone 4S does not work after update iOS 6.0

    WiFi iPhone 4S does not work after update iOS 6.0

    This sounds more like a hardware issue.
    Have you checked that the dock connector port is not dirty?

  • Flash player does not work after I installed it

    Flash player does not work after I installed it

    I'm using Mac Osx and my browser is Safari
    Date: Wed, 5 Feb 2014 00:41:29 -0800
    From: [email protected]
    To: [email protected]
    Subject: Flash player does not work after I installed
        Re: Flash player does not work after I installed it
        created by Mike M in Installing Flash Player - View the full discussion
    This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
    What OS are you using?
    http://mmonlinedesigns.com/images/os.png
    What browser?
    http://mmonlinedesigns.com/images/browsers.png
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
               Start a new discussion in Installing Flash Player at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Maybe you are looking for