Replacing a Imaging Server
Hi everyone,
We have 4 primary servers with version 11.2.1.6353. One of them is dedicated to Imaging. Actually, we have a problem with the preboot service that seems defect (novell-pbserv.exe) we have many errors on our Windows server events viewer. For now, I don't want to reinstall this server, don't want to change any configuration and versions.
my question: it is Ok to just shutdown this server ? This server doesn't have any other functions other than Imaging, so the 3 others primary servers will go on.... is there a problem to consider in let this server down?
After that I plan to just take another server and install zenworks 11.3 in a new zone, and reconnect my Images storage to it...
The purpose of doing all this is to let the original server unchanged for now...
thank you for your help and advice
DM
Dominicm,
> I would prefer to not delete the existing zenworks server.... I'm hoping
> to just configure a new one. I will check anyway the procedure
OK. In that case, just add another primary, but as I said, a satellite
will work equally well for imaging.
I was under the impression that you wanted to retire that server, but you
can equally well just remove the imaging role from it.
Anders Gustafsson (NKP)
The Aaland Islands (N60 E20)
Have an idea for a product enhancement? Please visit:
http://www.novell.com/rms
Similar Messages
-
We have replaced a SQL Server 2005 with a SQL Server 2014 (new physical server.) Have the new server set up to use SQL Server login OR Windows user login. Had old server connecting (for a particular DB) to front end Access (2010 or 2013) as guest for
anyone logged into the Windows NT Network with a read only ODBC connection. Have the DB in the new server set to include guest as db_datareader (with only SELECT permission for the securables of each table and view being linked) but when any Windows user not
specifically listed as a SQL DB user tries to use the front end they get an error of:
Microsoft SQL Server Login
Connection failed:
SQL State: '28000'
SQL Server Error: 18456
[Microsoft][OCBC SQL Server Driver][SQL Server] Login failed for user {domain\user}.
After closing that pop-up window a server login window appears. Of course, since the guest user is not specifically listed as a user in the DB that fails also. It seems like there should be a very simple solution to this, but I can't seem to find it. I want
to allow anyone logged in on the Windows system (locally) to be able to open the MS Access file (on their work station machine) and run their own (read only; select) queries on the SQL Server database. Any suggestions?
Thanks a billion in advance ----Thanks for the response Olaf. I have now spent weeks researching this. I realize that using the guest account in most situations is not advised. As mentioned, I have restricted the guest account to allow the db_datareader role only, and have explicitly denied
all other roles, as well as allowing select only, and still have no access for the guest account.
The suggested fix in the second link you provided, of using Windows groups is not plausible for my situation either. We are a scientific field research institution, with a few long term users and lots of users that may have Windows accounts for a few months,
and then they are gone. It would be a nightmare for the network tech to try to keep a group account up to date, and we need to give access (read only, of course) to anyone logged into the system. Realize that the ONLY access of any kind to this database is
thru MS Access ACCDB, using a (by default) read only OCDB connection.
This type of access is used particularly because researchers need to be able to set up their own queries, and the MS Access query interface is particularly convenient for people who are not themselves SQL experts, yet are trying to get some very advanced
levels of output. Putting the database online is not practical because then we are back to the need for a comprehensive query interface, and just picking up general subsets of the data online (from a basic web page search feature) would be out of the question,
since the result set would involve hundreds of thousands if not millions of records.
So - that said - what exactly would you suggest, assuming we don't have the funds to buy a whole new system, and have spent plenty of money with Microsoft's Enterprise level MS Office so that all work stations have MS Access, and Microsoft's SQL Server,
as well as running our network on Microsoft's network software. -
What's the process to replace an image inside a mask?
Hi There,
The new replace image function is a massive time saver but it doesn't seem to work with masked images.
These images are masked because they're part of an animation so I really need to replace them - not re-import and re-create the animation from scratch.
If this isn't possible, how do I remove the mask? That way I could just delete the mask, replace the image, then re-mask.
Any pointers in the right direction would be much appreciated.
Cheers
BenThe image replace works perfectly with a masked image intact, only if the two images dimensions are the same.
However, doing the following gets you 95% of the way with just a final tweak of the mask:
select the image on the slide
Format > Copy Animation
then replace image
Format > Paste Animation
Format > Image > Edit Mask -
New to java: how to replace an image extending a JComponent?
Hi,
I'm new to Java and I have a question about Swing:
I have a class called ActiveImage (entends JComponent, implements MouseMotionListener, MouseWheelListener) which takes an Image and displays it. It also receives some mouse events for zooming and moving it around. I display it in a JFrame using:
content = getContentPane();
content.setLayout(new BorderLayout());
image = toolkit.getImage (filename);
ActiveImage activeImage = new ActiveImage(image);
content.add(activeImage, BorderLayout.CENTER);
(This code is in a class extending JFrame.)
This works fine. However, this JFrame also contains a JToolbar with two buttons. Now when I click one of them, I want to replace the image with another one. I've tried removing it and creating a new ActiveImage to add that to content, but that didn't work very well. remove() resulted in a NullPointerException.
My question: what would be the best way to go about this?
Many thanks for any help,
Diederick de VriesB.T.W., this is the trace:
Exception in thread "AWT-EventQueue-0" java.lang.NullPointerException
at ActiveImage.ActiveImageFrame$1.actionPerformed(ActiveImageFrame.java:60)
at javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1849)
at javax.swing.AbstractButton$Handler.actionPerformed(AbstractButton.java:2169)
at javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:420)
at javax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:258)
at javax.swing.plaf.basic.BasicButtonListener.mouseReleased(BasicButtonListener.java:234)
at java.awt.Component.processMouseEvent(Component.java:5488)
at javax.swing.JComponent.processMouseEvent(JComponent.java:3093)
at java.awt.Component.processEvent(Component.java:5253)
at java.awt.Container.processEvent(Container.java:1966)
at java.awt.Component.dispatchEventImpl(Component.java:3955)
at java.awt.Container.dispatchEventImpl(Container.java:2024)
at java.awt.Component.dispatchEvent(Component.java:3803)
at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:4212)
at java.awt.LightweightDispatcher.processMouseEvent(Container.java:3892)
at java.awt.LightweightDispatcher.dispatchEvent(Container.java:3822)
at java.awt.Container.dispatchEventImpl(Container.java:2010)
at java.awt.Window.dispatchEventImpl(Window.java:1766)
at java.awt.Component.dispatchEvent(Component.java:3803)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:463)
at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:234)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:163)Just before this, it says "button clicked". The function that calls the setImage() goes:
theButton.addActionListener (new ActionListener() {
public void actionPerformed(ActionEvent ae) {
System.out.println("button clicked");
activeImage.setImage(image);
});Reading the trace, I would think that the exception has something to do with this last code, since it stops there (line 60 is the setImage()). If the setImage() function itself was where the fault was, wouldn't the trace end there?
I'm really at a loss here ... :-( -
How Can I replace an image and save the same size as the previous?
I want to replace an image in a PDF, but I would like to keep the same size, and location as the previous. I have tried to to it, but the new image takes a different size.
This is a PDF exported from an InDesign template.Thank you.
The problem is that the person to edit the PDF doesn´t have ID and doesn't know how to use it.
The idea is that the design department create very sharp ID templates for people from other departments of the company only have to replace information (text and image).
We are looking for a program to edit PDF files and function as templates forreplacement information. -
How to Replace Background Image?
I needed to replace a background still. In photoshop I changed the background still and saved it as itself.Then I opened Encore, but the old background still appeared. In the Project Panel, I selected the image and tried to replace it with the new image but I got the message that the asset was already imported. I went back and changed the name of the new image to a different name and retried to replace the old image. Encore di replace the old image with the new image in the Project Panel but did not replace the image in my menu. So I had to manually delete the old image in the menu, drag the new image into the menu and manually center it. Is there a better way?
I needed to replace a background still. In photoshop I changed the background still and saved it as itself.Then I opened Encore...
This makes it sound like you did this "outside" Encore, which begs for trouble.
Use "edit in photoshop" from inside Encore, so that Encore knows about the change you made.
Or delete the menu from Encore, change it, then import it in its changed form. -
Image server and images in the product catalog(CRM ISA)
Dear Gurus,
I am using CRM ISA 5.0 R/3 version. My products in the product catalog has got images. I have assigned the image's to the products in the R/3 product catalog(WWM2)
In the b2b XCM for the webcatalog node, I need to specify the imageserver url. Can you please tell me what goes here. How do I find out what is my image server in my landscape. Please advice me how do I get the images in my ISA product catalog.
Thanks!
Vivek.Hi Vivek,
In general image server is the web server. You need to talk to your network administrator to identify and setup the web server. Pass on the below document to your administrator to setup the publishing directories on the web server:
http://help.sap.com/saphelp_crm40sr1/helpdata/en/c7/d64e3c719d1742e10000000a11405a/frameset.htm
<b>Reward if helps</b>
Regards,
Paul Kondaveeti -
Cannot connect to imaging server after ZDML SP1 IR3 install
OK, here's a bit of an odd problem... well, actually, I hope it's an insanely easy problem that I just have overlooked a simple solution for. I guess that's for you guys to help figure out. ;)
We had been running Zenworks 7.0.1.0 on an OES1 Linux server with a few odd problems, mostly with remote management and inventory, but we never had a problem with connecting to it for imaging purposes (at least not since I took over management of the box not that long ago). Considering the remote management and inventory issues, I decided to update it to the latest version just to make sure it wasn't an issue that had already been fixed, but now that I have done that we can no longer connect to the imaging server for imaging. While I'd still like to get our original problems fixed, I'm more concerned about the imaging itself and can then revisit the first.
How I went about the upgrade: I followed the instructions at section 4.3 at ZENworks 7 Desktop Management with Support Pack 1 Interim Release 3a. Running ZDMstart shows "done" for bringing everything up, but when I try "/etc/init.d/novell-zmgserv status" it tells me that the Daemon is stopped; when I try "/etc/init.d/novell-zmgserv start" it says "failed".
When that failed, I downloaded the ZEN7_with_SP1_IR2_DesktopMgmtLinux.iso and ran that installation, then went through the steps on 4.2 to upgrade. (OK, this particular maneuver may not have been my smartest.) Same end results though.
I do recognize that I'm walking into a situation I didn't set up and there were other problems to start with. I have a feeling by the end of the year we'll be migrating to an OES2 server but, to be blunt, that project has been put off for other reasons here and again and I'd like to have something to work with in the meantime. Any idea where exactly the failed attempts would be logged to give me more to work with (I don't see anything in /var/log/messages)? Any other thoughts/suggestions are more than welcome; thanks in advance!
topherApologies in advance for any confusion; normally I post under this account, but the other day was logged in as tchristi2 for other reasons and forgot to log out... :/ In any case....
I tried uninstalling and re-installing ZENworks from the 7.1HP2 CD, and tailing the /var/log/messages file this line jumped out at me:
Sep 2 09:07:19 oes1 logger: We were unable to locate ndsmodules.conf at /usr/lib or at /usr/lib/nds-modules. ZENworks Imaging was not installed correctly.
I cannot find ndsmodules.conf in either of those locations; could someone help me figure out where it would be or why I might not have it? I may just punt and setup an OES2 box and move ZENworks to it, but at the same time I'd like to have imaging running until we do get that box up and going. Thanks in advance!
topher -
PT Transform Tag that outputs Image Server URL
I noticed something missing from the EDK that I wanted to get Plumtree's perspective on. We have instances where we need the imageserver URI through the facilities of a Transformation Tag. This useful when the portlet source document is native HTML and does not have server side scripting and also whn using an XSL transformation. In these cases, it would be nice to have a <PT:Image /> tag that can be used to transform into a full URL to an image.
e.g
<pt:image pt:src="/fld/subfld/image.gif" alt="sometext" /> --- would output<img src="http://ptserver/imageserver/fld/subfld/image.gif" alt="sometext" />The portal translates the token every time it finds a static URL, that is every URL that the transformer rewrites. It would work, for example, in an tag. The transformer does not rewrite style sheets or inline styles, so:
<td style="background-image: url('someBG.gif');">
would not get automatically rewritten. You can't use the pt:url tag here, either, since you can't nest XML tags inside HTML tags (note: that's why pt://images/ is a URL rather than an XML tag in the first place).
So I don't really have a good solution for this one. If this is a dynamic page, your best bet is to grab the image server URL from the EDK in the conventional way. -
Replacing a TFTP server in a cluster
Replacing a TFTP server in a cluster and with everything else being the same minus the MAC address on the NIC, are there any issues I could possibly run into here?
Thank you for the help the server is an MCS7845H2.No issues, MAC address is irrelevant on TFTP as it only matters on the Pub, simply install CUCM on the new server assigning the same IP and hostname and then restore from backup.
-
Is there a quick & easy way to replace an image within an image frame?
Is there a quick and easy way to replace an image in an image frame that is already set up with the proper effects?
In my example, I have a photo grid and just need to replace the photos periodically. Everything is already in place in the grid. I don't want to recreate the grid on the page.
I thought that I could have clicked to get the brown frame for the image and placed a new one, but that didn't work. Or, I could have right clicked and found something like "replace image", but that didn't work.
How can I quickly and easily just click on the image I need to replace and replace it with another one?There is an easy way to do this. Click on the image you would like to change and then change the fill to the new image. You will see the fill option in the upper left when you have the image you would like to change selected.
-
Replacing all image types in a book TIF - PNG
We recently have changed from using TIF's to PNG's we did some tests and found that was a better solution for us. I wanted to know if there was any trick or fix that FM could do so that when I open a chapter and the image reference comes up missing because of this file type change if I could actually not have to sit there for 5 hours pointing to each image that has the same name but now uses PNG rather than TIF.
There is also the issue of moving files that has always made me frustrated with FM. If I reference multiple folders for images I should only have to point to the folder once, but FM seems to see the files in order that they are listed so it won't replace referenced images from an older folder and associate all of those files from the missing folder to the new folder you point to when you "show it the reference".
The other half of this problem is replacing references to images used multiple times. If you tell the file that IMAGE1.tif is now newIMAGE1.png why is it that I have to do that for each time that image appears. It's not like FrameMaker shows me what the reference is so I have no idea where it's used.
I used to use BookUtils but this doesn't seem to be supported anymore.Just wanted to say that all my images are PNG and I have been using FM8; then, I downloaded the trial version of FM9, and FM9 pops-up windows of "missing files" to all my PNG grahics that I had initially created and linked to my FM8 documents. I then have to locate each and every file that I have saved in various locations on my network. Also, If I save a document with a new file name, in a different area on my network, the links to the files are broken and the "missing file" links pop-up in both FM8 and FM9. I don't know another way of locating and re-linking the PNG graphics to the new file paths other than to locate each one individually. It's costing me a lot of time to re-link graphics and I have many graphics and documents. Any suggestions? Demi
-
Can you replace existing images in Captivate 7 the way you can when using InDesign?
Can you replace existing images in Captivate 7 the way you can when using InDesign? I need to replace some images but wondering if I'll need to reformat, resize, rename for the Advanced Action, etc.
The work flow is a bit more complicated than in InDesign (keeps only a link to the image as you know in the frame). I understand the problem with the advanced/shared action references. This is my work flow, maybe someone else has an easier, shorter one:
Right-click on the image and use 'Find in Library' or use CTRL-ALT-F if it works on your keyboard (doesn't on my AZERTY one)
In the Library use the right-click menu to open the Properties or double-click the name of the image
In that dialog box, choose 'Import' and choose your new image; for some reason you cannot choose from the Library however, which I find really sad because I'm used to import all assets to the Library.
Drawback: if the new image has not the same width/height ratio, it will adapt to the original size of the image, you can use Edit image to repair. You'll keep the name of the image, you don't have to change advanced/shared actions. -
Does anyone know if you can use relative URLs in the Content and Collab config files to reach the image server or do these settings have to be an absolute URL?
On Thu, 05 Jun 2008 13:46:03 GMT, msad75 wrote:
> Anybody else running in to this?
traditional volume?
If you have already compiled drivers or have linux.2 please put them on
http://forge.novell.com/modules/xfmo...ect/?zfdimgdrv
Live BootCd and USB Disk from Mike Charles
http://forge.novell.com/modules/xfmod/project/?imagingx
eZie http://forge.novell.com/modules/xfmod/project/?ezie
Marcus Breiden
If you are asked to email me information please remove the - in my e-mail
address.
The content of this mail is my private and personal opinion.
http://www.didas.de -
Replace new image into existing project
I need to replace a image that I used in a transition. This image will fly in from the side from my start page to my main page.
I originally made everything the way I wanted then duplicated the state then I moved the items to be flown on to the page or faded into the page etc...
but now the new imported image is only on one state. if I copy the image from the main state and paste the image to the start state and try to make a transition the image only gets a fade in selection in the timeline. Even if I move the image it will still only fade in. I want the image to fly in from the side.
I think what is happening is that the image is no longer "Linked" between states so it does not know where the graphic starts and where it should end.
It thinks its 2 different graphics. Is their a better way than to copy and paste state to state to be able to keep the association and create a transition?
Otherwise I have to redo hours of work just to replace an image ?????
Please help....Hi Curtis,
Transitions are between the same item (or "instance" to be fancy) when it has different properties (like position, size, opacity, rotation,etc) in different states. When you import an image, you create a new item in the Art Board. If you copy-paste, you create another item.
If you want the same item to show up in multiple states, right click it and choose "Share to State" and the state you want it to appear in.
There's also a "Make same in All States" that makes an item have the same appearance in all states that it's present in.
For your specific case, though, you have transitions already working on an image, so you should just change the image to have a new source. Click the image that had been working before, click the "source" in the Properties Inspector (lower right), and you should have the ability to change where your image is coming from.
-Bear
Maybe you are looking for
-
Applications open and close without really starting
Often, when I download a 3rd party program (yes, I know, 3rd party, not supported, bear with me) and then try and run it, the program will appear in dock, bounce once or twice, the black triangle will appear and suddenly the program will just close a
-
I just received a replacement monitor for mine, which had stopped working. On the new monitor, I cannot see the lines between the dates on google calendar. It also appears that the color [in pictures] on the monitor is washed out. I have tried adj
-
Hi, I am trying to open a popup window in the onclick event of the <h:commandLink> I also have a action event that sets the values in the managed bean to be used by the popup window. But as onclick is fired before action event, the first time my popu
-
How to control manually the scrolling of Table Control?
Hi, I have one selection screen which takes me to the next screen (Screen 2) having a table control.In this screen I have some buttons like display, change etc ,by clicking on which it goes to the third screen.Now my problem is even when I try to ver
-
Hi, Any know problems for iphone with the ff specs? ============ 3GS model version 3.1.2 (7D11) Firmware 05.11.07 ============ My iphone signal is toggling from 2G to 3G while stationary. Any ideas how to fix this? Thanks.