Replacing an Airport Express with a Time Capsule but it won't connect to the internet.

Hello, I hope somebody can help.
I am trying to replace an Airport Express with a 2TB Time Capsule but it won't connect to the internet, via an ADSL modem.
I have tried everything I can think of, powering down all devices, re-setting all devices, but nothing seems to solve the problem.
When I first tried to set up the Time Capsule, there was an option to replace the Airport Express using the same settings.
But there were repeated error messages of 'No DNS Servers' and 'PPPoE server couldn't be found'.
I also had messages that the password for PPPoE wasn't correct, but when I plug the Airport Express back in again, everything works fine.
What could the problem be?

99% of issues with authentication are wrong password or wrong username.. eg it can be strange like the user name is missing the domain.. whereas the Airport Express works fine without it.
Ring your ISP and make doubly sure you have exactly the correct username and password.
If it still doesn't work, put the adsl modem back into router mode and try it again directly on the modem.. if it works ok on the modem but fails on the TC that is possible and can be caused by pppoe client using incorrect authentication type, CHAP or PAP which the TC does not allow you to select AFAIK.. some ISP do not give enough time to get the router to switch on auto to the correct authentication method.
In the end run the modem as router and bridge the TC. It will work just as well for most installations in bridge as the modem in bridge.

Similar Messages

Time Capsule 2TB 2013 won't connect to the internet

I recently got a new MBA (2013) and a 2TB TC with it. The TC can not connect to the internet. I have a basic motorolla router and my ISP is COX.
I can utilize the Time Machine functionality just fine and even managed to back up my system, however, the TC itself just wont connect to the internet. I have tried to reset the TC and even attemped a factory reset with no avail. Any suggestions??
Thank you.

Is the modem a router.. ?
If not the modem has to be power cycled.. for cable the off time can be 5min or might be longer 20min or so.. make sure the TC is in router mode.. (DHCP and NAT) and can get the public IP on the WAN interface.. if not please post screenshots of the setup and results of the connection. WAN ip in particular.

My macbook pro is connected to internet via my time capsule but my iPad and iPhone won't. it shows wifi connection to the time capsule but when i go on to the internet on the iPad or iPhone, it comes up with network error. can anyone help?

my macbook pro is connected to internet via my time capsule but my iPad and iPhone won't. it shows wifi connection to the time capsule but when i go on to the internet on the iPad or iPhone, it comes up with network error. can anyone help?

This can be caused by a number of issues.
Was everything working and then suddenly stopped??
Or is this a new clean setup and has never worked.
Do you have a cable modem which is not a router and the TC setup in bridge? That will cause it. The TC must be in router mode, ie dhcp and nat.
Check the IP the MBP gets including dns and gateway..
Then check the ipad/iphone.. post what IP dns and gateway (router in applespeak) they get.

HT4600 Airport Express light is solid green but I can not get on the internet. Any clues as to what is wrong?

Airport Exopress light is solid green, but I can not get on the internet. Does anyone have a suggestion how to fix this?

Would you please provide some more information about your current network so that we can help you? For example, is your AirPort Express the only router in your current network configuration? That is, is it connected directly to a broadband modem or to another router upstream of it? Regardless, what is the make & model of this modem?
When changing network equipment or when setting it up for the first time, it is always a good idea to perform a completer power recycle of your networking equipment. Please check out the following AirPort User Tip for the details.

I have just bought a Humax PVR and Humax W-Lan dongle to connect to my Airport Extreme. I have put the mac address into the AE. The installation screen is picking up my network name no problem but it won't connect to the internet. Can anyone help please?

I have just bought a Humax 7500T PVR and a Humax W-Lan dongle to connect to my Airport Extreme.
I have put the mac address into the AE. The installation screen on my TV is picking up the network name but once appied it won't connect to the internet.
I've a few other things connected to the AE such as computers, ipad, itouch, etc, and have never had a problem connecting these once I've entered the mac address into the AE. Can anyone help me with this please?

have you made sure that the network setting in the system preferences is set up to use dhcp? if not i would try changing it so that it shows that it is getting its address by dhcp

I created a wireless network with my Time Capsule but would like to connect this network to a WiFi Hotspot for Internet Access

I have created a Wirelss Network at home with the Time Capsule and would like to connect this network to the Internet.
I can't use LAN Cable to connect to it anything becasuse I usually use the WiFi that runs through my building.
Can I connect the Time Capsule to the WiFi hotspot somehow so that all computers on my network have Internet access and if so, what do I need?
I need this done because the computers can only be connected to either the WiFi network or to my Time Capsule Network at any given time.
Or is there a way to be connected to both networks simultaneously?
I have two PC's and two Macs.
Thank you for any support and I apologise for my ignorance. I am not too good with networking.
I have tried the silliest of things like connecting a router to the TC only to then realise that the TC had an inbuilt router.
I tried connecting a USB WiFI adapter to the USB Port on the TC but it doesnt detect it that way apparently.
Please help!

I have a kinda same problem @ https://discussions.apple.com/thread/3531642
Please reply (somebody)!
JeremyZ

Does my airport express need to be plugged to an ethernet to connect to the internet?

I am trying to set up my airport express so it can be connected to the wireless internet in my home, but no necessarily through ethernet chord so I can use the speakers with it in the other room.

Your Express does not require an Ethernet connection in order to gain Internet access. It must however be connected to another router that does via a wireless connection.
However how you would configure the Express to do so would depend on, whether or not, that other router is another Apple product (Express, Extreme, or Time Capsule).

Setting up an Airport Express with a Time Capsule

Merry Christmas! I received a new Airport Express for Christmas. My intention is to use it to stream music to my stereo. I have to admit that setting the AE up was not as simple as I had hoped it would be. I do have it working but I would like someone with more experience in this area to validate what I have done.
My wife and I each have MacBooks and we have a Time Capsule as our base station in the den. I would like to use the AE to stream music to my stereo which is in the living room. I would also like the AE to act as a "booster" to my TC, which I think is called "Extending a wireless network".
Here are my questions concerning the settings I have used in Airport Utility:
In TC, under AirPort, and the Wireless tab, I have checked the box for "Allow this network to be extended". Is that necessary?
In AE, under Airport, and the Wireless tab, there are a number of choices in the pulldown for Wireless Mode. I know I do not want to "create a wireless network" since that is what my TC is for. But all three other choices seem valid for what I want to accomplish -- Participate in a WDS network, Join a wireless network, or Extend a wireless network. I chose Extend a wireless network. I also checked the box under Network Name that says, "Allow wireless clients". Are these settings correct?
Here's the problem I'm having with things set up as I described above. AirTunes works fine. But if we close either of the MacBooks (put them to sleep) and open them in the living room which is closer to the AE, we seem to lose internet connectivity. When we open a browser or click on a link, it starts to load but then freezes. If I then walk the MacBook into the den, closer to the TC and restart the Airport or put it to sleep and wake it, its fine. Also, if we work long enough in the living room closer to the AE, it will also loose connectivity. I can sit in the den near the TC without any dropping.
Any suggestions on what the proper Airport Utility settings should be for my TC and AE would be greatly appreciated.

Your biggest mistake is confusing signal strength with signal quality. The signal indicator indicates strength and nothing else. You need to be using iStumblr to look at SNR (Signal to noise ratio).

How can I Connecticut two Airport Express with One Time Capsula?

Only by Wifi or by LAN in a row?

What are you trying to accomplish with the AirPort Express devices?
Where will the Express devices be located in relation to the Time Capsule?
If you are planning to use the Express devices to "extend" the wireless range of your network, Ethernet LAN will always provide far better performance than trying to connect the Express devices using wireless only.
You have the option of connecting both AirPort Express devices directly back to two LAN <-> ports on the Time Capsule....or....connecting one Express back to the Time Capsule and then connecting the second Express to the first Express using Ethernet. This assumes that you have a "new" Express with both WAN and LAN ports.
If you choose wireless only, both Express devices will connect back directly to the Time Capsule, so both of them should be located where they can receive a strong signal from the Time Capsule wireless.
A "hybrid" approach can also work. Connect one Express to the Time Capsule using an Ethernet cable and then setup the second Express to connect to the first Express using wireless only.

How do I extend my wifi using Airport express with my time capsul?

I want to extend my wifi from my time capsul. Can I do this with airport express? I have my wifi with cable so would I need to get another modem and hook the express to that? Would that help? I want to keep the same network and not add another.

You need to pay attention to something, while extending your network with the latest AirPort Express upgrade, your devices will be connected to it except your iPhone, you'll see your iPhone always connected to the capsule instead, even if you're at 1 foot from the AirPort Express.
You need to change the radio settings from automatic to 802.11a - 802.11b/g on your capsule, then I put it back to the default settings...
Now in the AirPort utility you should see your iPhone connected to the AirPort

I've had a new hard drive installed and reloaded all my stuff via time capsule and now can't connect to the internet although it say Airport is connected. How can I fix this problem ?

Just had a new hard drive for my iMac and reloaded all my stuff via time capsule, all works fine apart from Safari which won't connect to internet. Airport is connected but each time Safari comes back saying there is no connection....any help gratefully recieved.

So you have the apple rotuer called a time capsule and you have complete the frist time machine back up? but there is not internet access ?
If so.
Opem airport utiltiy on your Comptuer :
What is the IP ? > if its 169.254.xx.xx > its a self assigned
Try power cycling the Internet source for up to 1 mintue and make sure all the lights turn off.
In Airport Utility Version 5.5.3 / 5.6.1
Gi > Intenret > conncetiong sharing > Is it off bridge mode change it to share a public Ip address
In airport Utility version 6.0/6.1
Edit > network > rotuer mode : Should be DHCP and NAT unless you use PPPoE to conecnt to the internet then this is automatically invoked.

What is the best way to hookup my airport extreme with my time capsule ?

what is the best way to hookup my airport extreme with my time capsule ?

It sounds like you have the AirPort Extreme configured as the "main" router on your network.
If that is the case, connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the Time Capsule
Power up the Time Capsule
Connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the Time Capsule, then click Manual Setup
Click the Wireless tab below the row of icons and make sure that the setting for Wireless Mode = Off
Click the Internet icon, the click the Internet tab
Insure that the setting for Connect Using = Ethernet
Insure that the setting for Connection Sharing = Off (Bridge Mode)
Click the Update button at the lower right of the window and wait a full minute for the Time Capsule to restart
Then power cycle the entire network by powering everything off....order of power down does not matter
Wait a minute
Power up the modem first, and let it run a few minutes by itself
Power up the AirPort Extreme next and let it run a full minute
Power up the Time Capsule next and let it run a full minute
Keep starting devices one at a time about a minute apart until the entire network is back up
You will need to reset the backup path from your Mac to the Time Capsule to get backups going again
Open System Preference (gear icon on the dock)
Open Time Machine
Click Select Disk
Click the Time Capsule to highlight it
Click Use for Backups or Use Disk and backups should begin again in a few minutes
If you do not want to leave the Mac connected to the Time Capsule by Ethernet, remove the Ethernet cable from the Mac to the Time Capsule, then log on to the AirPort Extreme wireless network

Should I buy airport express, extreme or time capsule? I have my new Mac Pro. 2 iPhones, 2 iPads , and grandchildren who come with their devices. I live in a two-level house.

Should I buy airport express, extreme or time capsule? I have my new Mac Pro. 2 iPhones, 2 iPads , and grandchildren who come with their devices. I live in a two-level house.

A Time Capsule is an AirPort Extreme with a built in hard drive to allow your Mac(s) to back up automatically, so it's a logical choice if you need a wireless router and back up capabilities for your Macs
The AIrPort Extreme has a bit better antenna arrangement than an AirPort Express, so it would be a good choice for a two level house.
Depending on the location of the "main" wireless router, you may find that you still need to add an extender or two in other parts of the house for full, fast wireless coverage. The AirPort Express is a good choice for this duty.
To compare the 3 Apple devices, see this Apple support document:
Compare Apple Wi-Fi base stations AirPort Express AirPort Extreme Time Capsule

AirPort Extreme with 3T time capsule file security question

Right now I am using a MacMini with an external HD as a file server. I'm thinking g of using the new AirPort Extreme with 3T time capsule to do the same tho g (while also extended my wifi reach).
With the Mac mini I have fine control over who gets to see and do what to which folders and files. It seems that with the AirPort Extreme thee is no notion of permissions or access control -- if you can get on the wireless you can access the files. That is extremely insecure.
Is my understanding correct? Is there no way to secure files hosted on an AirPort Extreme so only certain users can access them??
- john

Are there any instructions for how to format and set HFS+ user permissions on the AP Extreme's HDD?
For the formatting part, you will need to temporarily connect the drive to your Mac, and then, use the Disk Utility (a part of the OS X operating system) to partition and format the drive. You should find this utility in the \Applications\Utilities folder. For HFS+, choose "Mac OS Extended (Journaled)" for the Format option.
For assigning user permissions using accounts, you will need to use the AirPort Utility.
Run the AirPort Utility
Select the Extreme, and then, click on Edit.
Select the Disks tab.
Select the HDD in the Partitions window.
Choose "With accounts" as the Secure Shared Disks option.
Click on the "+" button to add user accounts.
For each account desired, enter the Account Name, Password, and File Sharing Access type.
Click Save.
Click Update to write the new configuration information to the base station and wait for the station to restart.

I try to backup my Lacie Rugged Thunderbolt with my Time Capsule but the Lacie is not active (grey) in the Time Machine preferences. Why ?

I try to backup my Lacie Rugged Thunderbolt with my Time Capsule but the Lacie is not active (grey) in the Time Machine preferences. Why ?

@LaPastenague
Morning / Afternoon.
We may have an unfair advantage in that the Internet gets here faster than it does "down there".

Replacing an Airport Express with a Time Capsule but it won't connect to the internet.

Similar Messages

Maybe you are looking for