Routing an IP address to a different network with a RV042G

Disclaimer! I am not an IT guy.lol.  I need to route a set of ip's ( 100.10.10.x, 255.0.0.0) to a network that the ip's are 192.168.1.x, 255.255.255.0. I have a cisco RV042G router and have set the Wan to 192.168.1.51,255.255.255.0 and have the lan set to 100.10.10.244. I have tried the advanced routing tab but cannot ping between the two networks.

Dear steveelliott2
Why you are using different Classes? can you explain how many hosts you need in one network?
 draw sketch and let him post for details
regards
mshamsheer1

Similar Messages

  • Can I sync 2 apple tvs on different networks with same itunes account?

    I read that you can sync up to 5 tv's with the same itunes library, but do all tv's need to be on the same network?
    I've been able to successfully sync both apple tvs from my itunes account that's on my laptop. The first one works fine but the 2nd one keeps restarting itself while playing.
    I'm not sure if it's me or the apple tv.
    Has anyone else had this problem?

    Think I have it now. 2 tv's in different locations and on different networks, laptop connected to tv 1 over network 1 works fine, no go with tv 2 with laptop connected over network 2.
    Yes this could be an tv fault, you do however have the opportunity to check this. Swap over the 2 tv's if the problem moves with the tv it could be the tv, if it stays with the same network it could be the network.
    I'm not so sure it makes any difference but I assume you have named the two tv's differently in itunes.

  • Internet access in different networks with proxy without proxy

    at home i connect to a network with an internetaccess without proxy, in the enterprise I connect to a network with an internetaccess via proxy. How to configure the iPAD?

    Hi Porras,
         Try creating an exception for your proxy-server - see pics attached (Win XP SP3).
    Note: These proxy exceptions can be created programatically, by modifying the Windows Registry.
    Cheers.
    "Inside every large program is a small program struggling to get out." (attributed to Tony Hoare)
    Attachments:
    net_proxy_adv.JPG ‏29 KB
    net_proxy_adv_except.JPG ‏30 KB

  • [Question] Dynamic NAT on 2 different networks

    Hi,
    I just want to ask if its possible to have same dynamic translation within 2 different networks like:
    interface gig 0/1
    1.1.1.1 255.255.255.0 (LAN Connection w/ DHCP enabled)
    inteface gig 0/2
    2.2.2.1 255.255.255.0 (Wireless Connection w/ DHCP enabled)
    Actually, the scenario was 1.1.1.1 is my LAN connection and 2.2.2.1 are my Wireless connection.
    Hope this merits their favorable response. Thanks.

    Hi,
    Do you mean that you want both of the said LAN networks to use Dynamic NAT/PAT towards a third interface on the ASA?
    If you simply want to use the same NAT/PAT address for 2 different networks on the ASA then you can use the following configurations as example
    These are PAT translations to a single IP address. Using a NAT Pool would change the configurations slightly.
    For ASA software 8.2 and below
    global (outside) 100 3.3.3.1
    nat (inside) 100 1.1.1.0 255.255.255.0
    nat (wireless) 100 2.2.2.0 255.255.255.0
    Where
    outside,inside and wireless = Interface "nameif" on the ASA firewall
    100 = Is just an ID number for the NAT configuration. You can use other one also
    For ASA software 8.3 and after
    object-group network PAT-SOURCE-NETWORKS
    network-object 1.1.1.0 255.255.255.0
    network-object 2.2.2.0 255.255.255.0
    nat (inside,outside) after-auto source dynamic PAT-SOURCE NETWORKS interface
    nat (wireless,outside) after-auto source dynamic PAT-SOURCE NETWORKS interface
    Where
    PAT-SOURCE-NETWORKS = Is an "object-group" where you can define the source networks for the NAT/PAT rule
    Hope this helps Please if you found the information helpfull
    Feel free to ask more if this didnt answer your question.
    - Jouni

  • Wireless roaming in different networks

    Hello,
    In Wireless networks if we have two different networks with the same SSID when we pass from one network to another network, the client will change the ip network automatically or we need to disconnect and connect again to request another ip?
    I would like to know this information to Flexconnect and local. 
    Thank you.
    Best Regards
    Cristiano Nunes.

    Hello Cristiano,
    You don't need to disconnect and connect again if you have Layer-3 Roaming enabled.
    To configure Layer 3 Mobility, following requisites should be considered.
    SSID and security policies should be same across MAs.
    Client VLAN ID should be different for Layer 3 roaming.
    Either one or both of the bridge domain ID and client VLAN ID should be different for Layer 3 Roaming.
    Please find the attached topology for better understanding.
    Regards,
    Moin Ilyas.

  • How to use Airport Extreme to create a second wireless network with different IP addresses behind an existing modem/router?

    Hi,
    I have an existing modem/router from my ISP that does DHCP and NAT with base IP 192.168.1.1 distributed in the wireless network. I use this wireless network for our private devices. I could turn off the DHCP server in this first router, but there isn't a separate setting to turn off NAT.
    I want to connect my Airport Extreme (4th gen) to this existing router to create a separate wireless network for visiting guests, where IP addresses of 10.0.0.0 etc. are used. So I do not want to use the Airport Extreme in bridge mode, as I would like to keep the devices on the first network 'invisible' for those on the second network. (P.S. when connected in bridge mode, the Airport works well and can distribute a network with a different name from the first. It's just that I would feel more comfortable about our privacy if the Airport were to distribute a different IP range. False security, maybe?)
    I've tried doing this by 'Sharing a public IP address' in Airport Utility's Internet tab, leaving TCP/IP's setting to 'via DHCP', setting DHCP addresses to start with 10.0.0.2 up to 200 with all else blank, and not using a standard host nor NAT-PMP in the NAT tab.
    When I do this the Airport complains of a 'double NAT issue'. Internet connectivity seems to be OK, but when switching between the two networks on my Mac I get complaints about my IP address being in use by another device intermittently.
    Can anyone help in how to get the 'double NAT issue' resolved?
    Thanks!

    So if someone is connected to the modem/router network they will be able to see the HD I will have put in to the AirPort Extreme?
    As I said above.....since the modem/router and AirPort are bridged, devices on the modem/router wireless will be able to "see" devices on the AirPort wireless, and vice versa.....
    If they can see the HD connected to the AirPort Extreme, will they be able to access it
    Yes, unless you plan to password protect the drive connected to the AirPort Extreme.
    or will they still need the password needed to get onto the AirPort Extreme network?
    The modem/router and AirPort Extreme are bridged. They are on the same network. All devices are on the same network when the modem/router and AirPort are bridged. Not sure how else that I can say this.
    Also, because it is bridged, I shouldn't have any problems accessing the HD I will have connected to the AirPort Extreme from an external location?
    Accessing devices from a remote location is never easy....and a topic for a different post/discussion. If you have a "static" Internet IP address from your provider, and have all the details on how to forward ports on your modem/router, you are off to a good start.
    Apparently there is some addressing issues because devices can be seen as "Double IP" because the modem/router would have allocated IP's as well as the AirPort allocating IP's thus making connections slower until resolved
    When you "bridge", all IP addresses are issued by one device. There will be no conflicts on the network, since they are bridged.
    Once again, in very simple terms, you have two doors (access points) that open into the same room (network).  One "door" is the modem/router and the other "door" is the AirPort Extreme. They are on the same network....("room") because they are bridged.

  • Add Wireless N Router To Network With An Actiontec Router

    Hi everyone, I know this wireless N thing is being beaten to death but I just really need to be pointed in the right direction.  I recently built a HTPC setup with a SiliconDust HD Homerun network tuner so I could share three tuners with computers on my network.  I've got two PCs wired to the network right now which share them fine.  But the problem I'm running into is when I try to set up my laptop to watch something wirelessly, usually a game in HD.  The signal is very weak and I constantly lose the tuners because of that, not to mention the picture is very choppy.  I saw on a Microsoft Windows Media Center site that they don't recommend streaming HD TV feeds over anything other than a wireless N connection.  I currently have the standard Actiontec router that came with FiOS, and it doesn't the N band.  Now, that router accesses the internet signal through a coax so I know I can't get rid of it, but I've seen mentioned in a couple of places that you can just add a wireless N router into the network and turn off the wireless on the Actiontec router.  This is the router I was thinking of getting:
    http://www.bestbuy.com/site/Cisco+Linksys+-+E1200+Wireless-N+Router+with+4-Port+Ethernet+Switch/2225...
    My current network setup is like this: Actiontec router upstairs which carries internet to -> a gigabit switch connected to -> computer, tuners, and printer upstairs, with a line run to -> another gigabit switch downstairs which connects to -> a computer, and an XBox. 
    So a couple of questions about this:
    - Where would this go on the network?  Would it go after the router and before the switches, like I run the internet into the new router then out to the switch, or can I just add it to one of the switches?
    - Will I need to do any sort of port forwarding or anything, or assiging of IP addresses?
    - Anything else I should know or might run into?
    I love my FiOS service so hopefully this will help me get even more out of it!
    Solved!
    Go to Solution.

    I wanted to upgrade to an N protocol wireless router but since Verizon doesn’t offer the option, I purchased a Netgear N600. Unfortunately, after it arrived, I discovered that it didn’t have a coax connection as did the Verizon Actiontec. I then set out to find out how to daisy chain the routers to leave the Actiontec connected to the coax and connect the two routers via Ethernet cable. To my good fortune, during the time I spent on the phone with Netgear, I learned my way around their router interface and with the help of a co-worker that actually has a solid understanding of router/network configuration, I finally got everything working correctly – my port forwarding for RDC login worked, I could connect devices to either router and everything could once again see each other (e.g. PC, printer via Ethernet, Blu-ray player for Netflix, receiver for streaming Windows Media Player). Hopefully, this post will help you get up and running quickly and avoid the several hours I spent groping in the dark for the correct configuration.
    Login to Verizon Actiontec router (type 192.168.1.1 into browser address bar).
    No configuration changes are necessary on the Actiontec, you just need to identify an open IP address range in My Network section (I chose 192.168.1.50). This will be used as your static IP address of the Netgear router LAN settings.
    Connect you PC via Ethernet cable directly into an Ethernet port (not WAN/Internet) on the Netgear router. No other connections are needed at this point.
    Note: Do not use the Netgear wizard CD to setup the router. It will not take you through the necessary steps as you’re not setting it up as a router.
    Login to the Netgear router (type routerlogin.net into the browser address bar) using the default login of “admin” and password “password”. Depending on your firmware version, your interface may vary but hopefully you’ll be able to find the same configuration options in either but perhaps not in the same order or placement. For subsequent logins after the router is active, you may need to type the Netgear IP address (e.g. 192.168.1.50) as routerlogin.net may open a search.
    At the top of the Netgear genie, click on the Advanced tab.
    On the left side, expand Setup, then select Internet Setup.
    Select “Get dynamically from ISP”, under Internet IP Address.
    Under Domain Name Server (DNS) Address, select “Use These DNS Servers”, and enter the IP Address of your Actiontec router (e.g. 192.168.1.1) in the Primary DNS” field.
    Next go down a few options  within Setup to Wireless Setup.
    In the Wireless Network 2.4GHz section, click Enable SSID broadcast.
    Enter a meaningful name in “Name (SSID)” as this is what will be displayed for your wireless connection.
    For Channel, select Auto.
    For Mode, select “Up to 300 Mbps”.
    Security Options, recommend WPK2-PSK[AES] for longer/stronger password options.
    Set the password of your choice.
    Repeat the same process for Wireless Network 5GHz, except vary the name slightly so you’ll be able to distinguish which band you’ll connect to. You can optionally use the same or different password as your 2.4GHz. The only exception is you’ll have to select a Channel of your choice.
    Next go down a couple more options within Setup to the LAN Setup.
    In the LAN TCP/IP Setup section, enter the IP Address you chose in step 2 (e.g. 192.168.1.50).
    Enter the IP Subnet Mask 255.255.255.0
    Leave the block for “Use Router as DHCP Server” blank as your IP assignment will be handled by your Actiontec router.
    You’re now finished with the configuration and you can connect the Actiontec router to the Netgear router using an Ethernet cable using the LAN ports (Note: do not connect the two routers using the WAN/Internet ports on either). You may connect your devices (PC, printers, A/V devices, etc.) to either router. If you have devices that are gigabit capable, you’ll want to connect them to the Netgear router to take advantage of the higher speed.
    To avoid any possible interference between the 2.4GHz range of the two routers, you can optionally turn off the Actiontec wireless capability by logging into the Actiontec router admin (described above), go to the My Router tab, and there should be an option for “Change Wireless Settings” in the Quick Links section. Option 1 allows you to turn On/Off the wireless portion of the router.

  • Just bought new time capsule- need help setting up WiFi network with another router

    Here ismy situation.
    I had a wireless network setup up at home using a Belkin wifi router.
    I have 2 macBooks (1 pro, 1 air) and 2 iphones that connect wirelessly and a desktop PC that is hard wired to the ethernet port.  In addition, I have a Verizon wireless network extender plugged in by ethernet.  All of the hard-wired gear is in our 3rd floor attic office (and the wireless signal was strong throughout the house).
    The Belkin wifi router was plugged into a wall ethernet jack that is in turn wired into a Linksys router in the basement (along with multiple other ethernet ports througout the house) and is hardwired to the Cable modem next to it.  All of the hard-wired ethernet stuff (including the router in the basement) was there when we bought the house, and I have no clue in the tangle of wires how to sort them out (but don't really think I need to)
    I just purchased a TimeCapsule to do wireless backups of my 2 macbooks, and tried to set it up alongside the existing wireless modem.
    Needless to say, this did not work well. I called  AppleCare, and was told that the TimeCapsule needs to be the "1st" wireless adapter, so I went into the basement, and connected the time capsule directly to the cable modem, and then out to the basement router.  The Belkin router still needs to be in the attic to supply the PC and the Verizon adapter (so it is near a window for GPS signal). 
    If I try to name the WiFi network the same SSID on both the TC and the belkin router (to have dual signal strenth coverage) the whole thing gets messed up and the TC cannot be "found" by the aiprort Utility software.
    What I have done now is that I have 2 side-by-side wireless networks with 2 unique names (actually 3, because I enabled the 5Ghz signal on the TC), but our wireless devices do not "switch" automatically from one SSID  to another stronger signal SSID as we move through the house
    Here's the question: How do I name them the same so that the devices will switch effortlessly to the stongest signal?  I understand it involves switching the "channels" but don't know how to do it right now.  Currently, everything works, so I don't want to mess it up tinkering.  Another caveat- there are several other wireless networks from neighbors houses that I can "see".  I jsut downloaded a program called iStumbler that shows the channels, but not sure what to do with that info.
    Any advice would be appreciated.

    Here's the question: How do I name them the same so that the devices will switch effortlessly to the stongest signal?  I understand it involves switching the "channels" but don't know how to do it right now.  Currently, everything works, so I don't want to mess it up tinkering.  Another caveat- there are several other wireless networks from neighbors houses that I can "see".  I jsut downloaded a program called iStumbler that shows the channels, but not sure what to do with that info.
    Any advice would be appreciated.
    OK.. sounds like a mess.. or at least messy and the previous people should have left a log book with all the IP address info in it.. you have far too many routers.. but from here it is impossible to tell how they are configured. Most are probably just setup as AP.
    Naming rule for wireless.. Same SSID same security different channel.
    SSID ie wireless name to work on the PC side should have no spaces and no special characters. TC name should also follow that rule. So the devices need to all set with fixed channels.
    Don't worry too much about iStumbler and what is outside your house.. there isn't enough channels at 2.4ghz anyway. And you are going to need to use them all. There are only three non-overlapping channels. 1, 6, 11 so set each device to one of those channels. The TC should be as close as you can to where you normally use the MacBooks.. and turn on the 5ghz. You will have to leave it to automatic name so the Macbook can also roam across from 2.4 to 5ghz. But if you care to use a different name and force it onto 5ghz the speed is much better as long as you are in the same room.
    Roaming is great in theory.. often in practice it just doesn't work.. you need to step in and turn off wireless and then turn it back on.. you can quickly see which router it is connecting to by hold down the option key when you click the airport fan in the top menu area.. and look at bssid.. you will have to figure out which number MAC address relates to which router.
    Also do not be surprised if Lion gives you issues. It seems to often drop out and lose connection to the TC as a backup device even if internet is still working.

  • Laserwriter 8500 - networking with D-link router

    Hi,
    I've just changed my router to a D-link DI-524 and can't get my Laserwriter 8500 to work with it. It was fine with the Netgear Router I used to have.
    I'm running a MacBook with OS X 10.5.6, and the printer driver is v.3010.103.
    I tried some of the advice on other threads but when I go to Printer/Fax prefs and click 'Default', nothing shows up and the 'Add' Button is dimmed. Tried the IPP setting but didn't really know what I was doing.
    Help!
    Thanks,
    Debbie
    PS this was the reason I bought this router, so that I could network the printer.

    That is a printer than can print as either an Appletalk printer or an LPR/LPD printer (also called an IP Printer). The easiest way to change printer parameters is with Apple printer Utility. If you do not have a Mac that can run Classic, you cannot run Apple Printer Utility, and may be stuck with Telnet to change printer parameters.
    To set it up as an Appletalk printer, you must turn on AppleTalk on your Mac, which is accomplished in:
    System Preferences > Network > (your active network interface) {Ethernet or Airport}
    (Turning Appletalk on for one interface may give you a message that you are turning AppleTalk off on a different Network Interface; not a problem.)
    Then you need to use Printer Setup and deliberately choose AppleTalk as the connection method -- I do not think default will suffice. (No AppleTalk Zones are involved.) If your printer is turned on, ready, and cabled in, it should appear within a quarter minute.
    Some Routers, especially less popular brands, may not support AppleTalk packets transmitted over wireless.
    That printer can also be set up as an IP Printer. To run it as an IP Printer, it must have an IP address in the same subnet as your current Router. \[Post back if you do not understand what that means.]
    The discussion referenced below has some information that may apply. The original Poster was trying to set up the printer as an IP Printer, then wanted to change to a different Router using a different Internet Service Provider:
    Topic : LaserWriter 8500 needs new IP address

  • Problem using Tuxedo from different network

    We are using Tuxedo (7.1) with Clarify eFrontOffice.
    We are trying to access Tuxedo from a different network. We have a NAT address and opened the port for WSL (48800) and also a range (specified in the ubbconfig and compiled) specified for the WSH. When the Clarify client is started, it is connecting to the WSL on port 48800. When tuxedo returns the WSH port to the Client, it is also returning the IP of the server. Since the IP is not recognized in the 2nd network the communication is failing. Is there a way to retun server name instead of IP or a different IP?
    Thanx

    Raju,
    When using Network Address Translation with /WS you should specify the -H
    option to WSL (after the -- option) so that the address of the WSH can be
    mapped back to an address that the client will understand. A bug related to
    the WSL -- -H option was fixed at Tuxedo 7.1 rolling patch level 165, so you
    should obtain the latest 7.1 rolling patch if you are running at an earlier
    patch level.
    The description of the -H option at
    http://e-docs.bea.com/tuxedo/tux71/html/rf537.htm is as follows:
    [-H external-netaddr]
    Specifies the complete network address to be used as a well known address
    template of the WSH process. The address will be combined with a WSH network
    address to generate a well known network address used by the Workstation
    client to connect to a WSH process. It has the same format as the -n option
    except that it substitutes the port number with same length of character M
    to indicate the position of the combined network address will be copied from
    the WSH network address. For example when address template is
    0x0002MMMMdddddddd and WSH network address is 0x00021111ffffffff then the
    well known network address will be 0x00021111dddd dddd. When address
    template starts with "//" network address type assumes to be IP based and
    the TCP/IP port number of WSH network address will be copied into the
    address template to form the combined network address. This feature is
    useful when Workstation client needs to connect to a WSH through a router
    which performs Network Address Translation.
    <Raju Vatsavayi> wrote in message news:[email protected]...
    We are using Tuxedo (7.1) with Clarify eFrontOffice.
    We are trying to access Tuxedo from a different network. We have a NATaddress and opened the port for WSL (48800) and also a range (specified in
    the ubbconfig and compiled) specified for the WSH. When the Clarify client
    is started, it is connecting to the WSL on port 48800. When tuxedo returns
    the WSH port to the Client, it is also returning the IP of the server. Since
    the IP is not recognized in the 2nd network the communication is failing. Is
    there a way to retun server name instead of IP or a differen
    t IP?
    Thanx

  • Error The PC and the printer are connected to different networks

    Hi,
    I'm trying to set up my C4580 on my laptop, but I'm getting  the following error after the diagnostic test:
    The PC and the printer are connected to different networks(237DB2A87D and 66616B65). They must be connected to the same network. This can happen when you use the manufacturer's default network name (SSID) and another nearby network is using the same name. 
    My setup is a Linksys router WRT546,  my laptop is conntected wireless to the router.  I have two other desktop computers that are directly connected to the router.  Both the desktops are able to connect wireless to the printer.  My router SSID name is 'Blair Office' with WPA security.
    I get a internet connect fine with the laptop, but can't get the new printer to setup.
    I saw another post that talked about 'Print the C45** Network Configuration Page', but not sure how to do this
    Thanks
    Diane

    This reply may be late for this user, but it might be helpful for any current users.
    I managed to change the modem's IP address to match that of the printer. In my case the printer worked fine wirelessly until I moved to a new place and installed a new modem. Here is what I did to solve the problem:
    1. At the printer, click on the wireless button, wireless settings, print network configuration page. This will print a page with the printer's IP address (in my case: 192.168.0.13)
    2. I accessed my modem via the internet browser, typing 192.168.1.1 (this is one of the default addresses (192.168.0.1 is also common). Default user and password is admin (usually). There I changed the modem's IP address to 192.168.0.1 and the range to start at 192.168.0.13 (my printer's IP address).
    3. I saved the settings (the modem will reboot and you will be offline, it may take some 20 seconds before the modem is visible again).
    4. Reconnect to the modem and check if internet is still working. Then try to install the printer again.
    This worked for me after I read several other postings.
    Good luck!

  • Worth buying a MBP right now??   (Are WiFi/router issues being addressed?)

    I was planning to buy a new Macbook Pro, and then I began reading about all the wifi connection issues. Is Apple working on a fix for this? I am no techie and the thought of having to debug a router configuration so that I can get my MBP connected to the internet is not appealing. What is the status of this issues, as of Dec 29, 2008? (I plan to use my MBP downstairs via a wireless connection to my PC upstairs that is cabled into the wall and uses a cable modem. I'll buy the router for the PC when I purchase the MBP.) Thanks for any input!

    If you look at various update description pages, you'll see Airport is addressed for certain reasons:
    10.5.6:
    Improves the reliability of AirPort connections, including improvements when roaming in large wireless networks with an Intel-based Mac.
    10.5.4:
    Addresses AirPort reliability issues with 5GHz networks.
    Addresses AirPort issues that may result in slower performance in Logic Studio or MainStage.
    10.5.3:
    Improves 802.1X behavior and reliability.
    Improves reliability when using Time Capsule.
    10.5.2:
    Improves connection reliability and stability
    Includes 802.1X improvements.
    Resolves certain kernel panics.
    10.5.1:
    Allows password-protected accounts on AirPort Disks to show up on in the Finder's Shared Sidebar.
    Resolves an issue with saved passwords for wireless networks.
    10.4.9:
    Adds support for WPA2 encryption in Network Diagnostics.
    Addresses an issue with automatic AirPort connections that use different authentication methods.
    And then there are all these Airport downloads:
    http://support.apple.com/downloads/#airport
    Suffice it to say, Apple hasn't been standing still. One problem is, neither has the industry, and 802.11n is still a draft standard which no one company seems willing to settle on.
    http://en.wikipedia.org/wiki/802.11n
    Until everyone does, networking will be a constant cat and mouse game with wireless.

  • Does tcp works on different networks

    Hello, 
    I have a problem with TCP/IP communication. 
    I write a program for TCP/IP communication (server-client) and it works fine when I tested in office (the same network). But when I tested program when server and client VI are connected to different network I dont have any communication.
    Does TCP/IP work when client.VI and server.VI are connected to different networks? If not, does anybody have suggestion which protocol to use? Problem is that server VI must be in exe format but client VI must be open for change.  
    Thanks
    Solved!
    Go to Solution.

    I think we have to clear up some things before going into detailed "debugging".
    First of, when talking about "networks", i expect you to refer to "LAN" (local area network). A LAN often uses a dedicated "subnet" identification, which is a combination of the IP address(es) and the subnet mask. The subnet mask defines which part of the IP address refers to the LAN identification, the "rest" of the IP refers to the specific PC.
    An IP(4) address consists of four bytes, a subnet mask gives instruction on how many bits and bytes are the "LAN ID". Subnet masks often are 255.255.255.0.
    So when saying "works in office (same network)", you do mean: same subnet. Correct?
    (All IP addresses share the same values in the bytes of the subnet mask, but differ in the rest. Example: PC A 192.168.1.12, subnet 255.255.255.0. PC B 192.168.1.15, subnet 255.255.255.0.)
    If the PCs are NOT within the same subnet, it depends on the network setup on how to proceed. If there is a "direct connection path" from A to B, simply the target IP address is sufficient (e.g. A 192.168.1.15, subnet 255.255.255.0, B 11.88.2.126, subnet 255.255.255.0 works if subnet 192.168.1 has direct connection to subnet 11.88.2).
    If there is NO direct connection, you require "port forwarding" on the hardware (router) inbetween. This can get quite difficult.
    So depending on the goal of this request, you maybe better re-architect the approach of loading dynamic components in your application.
    Norbert
    CEO: What exactly is stopping us from doing this?
    Expert: Geometry
    Marketing Manager: Just ignore it.

  • C4780 PC and Printer on different networks

    Please help - I have just purchased a C4780 wireless printer, for a home with 3 laptops. Two of the laptops have been set up fairly easily to print wirelessly, but for the third I am getting the following message :
    The PC and the printer are connected to different networks(192.168.103.0 and 192.168.1.0). They must be connected to the same network. This can happen when you use the manufacturer's default network name (SSID) and another nearby network is using the same name.
    We have only one wireless router, a Linksys with SSID Linksys-6102, and that is identified on the printer's network test report, ( the only other listed is one called NETGEAR )  and also on the third laptop, as well as both of the others.
    The router's IP address is 192.168.1.1
    The printer's IP address is 192.168.1.104
    One of the successful laptop's address is 192.168.1.102
    The one I'm having a problem with has address 192.168.103.1
    Can anyone help suggest a solution?

    It sounds like the printer is on your network (Linksys-6102), but the third PC may be connected to a neighbor's (?) wireless network named NETGEAR.  It the third PC is connected to a neighbor's network, it will not see anything on your network.
    Your neighbor probably has a NETGEAR router with no security, which is a huge risk for them and a pain for you since your PC's will sometimes jump onto it instead of your own network.  If you know whose it is, talk them into changing the SSID and adding WPA or WPA2 security to it.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Networking with airport express and another router

    I have an imac and a powermac G5 connected to the internet by ethernet cables going through a router, and i recently bought 2 powerbook G4s and an airport express. the laptops are connected to the internet via the airport express (which is connected to the main router with an ethernet cable), and i can access the internet on all of them. However, i cannot share music or files between all of them, only between the imac and powermac connected by ethernet. The laptops seem to be on different networks, and i cannot share files or music between them or with the imac and powermac. is there a solution to this?

    Absolutely this solution will work - it has worked perfectly for everyone (including myself) that has done this. Likely what you didn't do last time (and which I pointed out you must do) is restart all your wireless computers after making this change on the Airport Express. This forces all wireless computers to renew their IP addresses, which must now come from the cabled router on your network.
    Just to be sure you have explained your setup correctly - please tell me what make/model of router you are using.

Maybe you are looking for