[RVS4000.v2] How to setup Itemized DHCP addressing

Running RVS4000 on Cable modem.
'Itemized', is probably the wrong word I used in the subject line but this is what I mean:
Some small business type routers allow the user to setup the dhcp addressing so that specific hosts always get the same dhcp address, but I don't see how that might be done on the RVS4000_v2.  The router I just quit using was a NETGEAR FVS-318.  I ditched it in favor of the RVS4000 just for the gigbit lan ports, and still trying to learn to use it, at least as well as I was able to use the Netgear.
On that Netgear, it was clearly marked and notated how to setup the situation I described above, but I'm not finding anything I recognize in the `lan'  settings, on RVS4000 that I can recognize as a way to make that kind of setup.
Is it possible to make the dhcp server, serve the same IP address to a specific host?  Can anyone tell me how it is done?

mpyhala wrote:Hi Harry,Thank you for posting. Right under Server Settings (DHCP) in the setup page you should see Static IP Mapping. This allows you to have the DHCP server provide IP addresses based on the MAC address of the client. Each time that MAC address requests an IP address it will receive the same one. Please let us know if this is what you are looking for or if you need further assistance.
Yup, that was what I needed, thanks.
The terms describing that section are pretty confusing.
Static IP mapping
And then the first question with dialog box to fill in is titled
Static IP:{     }
Well, one would expect this to be about assigning Static IPs as its called in several places here.
Though it may actually be a nonsense term, sometihng like like `DHCP derived Static IP', might be a better choice of wording. So the user knows this involves dhcp and not plain Static IP assignment.
But anyway, its what I was after so thanks again.

Similar Messages

  • How to setup IOS DHCP server for redundancy?

    Hi
    The customer has 2 core (cat6). Plan to enable DHCP service on them for IP phones.
    How to setup them so there is a redundancy for DHCP service?
    Thanks in advance!

    Setup two routers and have them split the range of addresses that they lease out. The pools should be non overlapping.

  • How to setup a Class B network with WRT54GX ver. 2

    Hi all,
    I bought a WRT54GX ver. 2 router. I wanna know how to setup the IP address say 128.1.50.136 with subnet mask 255.255.0.0 (Class B network)? By the way, 128.1.0.0 is my network zone.
    If the router can't change, what should I do? Any other router support Class B network?
    Thanks!

    bcow wrote:
    I did but it doesn't work. It seems don't have 255.255.0.0 to select.
    would you state more clear of how to do it? Thanks!
    It does not have that because it does not support it... the router runs on CLASS C only because it was designed and made for SOHO only... bussiness lines of Linksys or Cisco can do that....but not this router...
    "Sometimes your knight in shining armor is just a retard in tin foil.."-ARCHANGEL_06

  • How to setup rescue email in icloud

    i want to know how to reset the security questions of an icloud account as i have the password but dont remember the security answer of the icloud account and
    also want to how to setup rescue email address in icloud account as there is no rescue email id in my account please guide and assist with the problem.
    thankyou

    Dear John,
    Goto Tcode SCOT:Node>create node>give node name and description>ten continue>choose RFC or HTTP radio button>if say you choose RFC>continue>click address type>then continue-->check various options
    Check Tcode SCOT, the configuration of the SMTP should look like:Mail Host: the Exchange server domain name (FQDN)
    Mail port: 25
    Code Page: what ever you need (like 4110 unicode UTF8)
    in the supported address choose Internet then click on the SET button and include your company address like:@XXX.ac.in:)
    In the SAP's user manager (SU01) the user need an email address to be able to send emails.
    Please check weather the default domain in transaction SCOT>menu>settings is set or not.
    Check SAP note If you use SMTP check the note --> 455140,487754. & 455140 Also check that in Tnx SCOT
    -->Node SMTP
    -->Supported address type
    -->button internet set.
    --> Address area
    '*' must be there.
    Regards,
    Ashutosh
    Edited by: ashutosh singh on Sep 3, 2008 7:08 AM

  • Step by step guide to setup NAP DHCP Enforcement on a separate DHCP server & NPServer?

    Hi,
    Any one has a link or instructions on how to setup NAP DHCP Enforcement with a separate DHCP & NPS (Network Policy Server)?
    Regards,
    Mon

    Hi,
    Video in the web page will demonstrate how to setup a DHCP enforcement of NAP：
    Network Access Protection using DHCP in Windows Server 2008 R2
    http://social.technet.microsoft.com/wiki/contents/articles/network-access-protection-using-dhcp-in-windows-server-2008-r2.aspx
    you can also reference the link below：
    Checklist: Configure NAP Enforcement for DHCP
    http://technet.microsoft.com/en-us/library/cc772356(v=WS.10).aspx
    Best Regards,           
    Eve Wang

  • How to setup default gateway in a DHCP client. The default gateway will be the Ip address of the server that has RRAS installed, hence routing cabalities.

    How to setup default gateway in a DHCP client. The default gateway will be the Ip address of the server that has RRAS installed, hence routing cabalities.

    Hi Bill,
    Thank you for replying back...Yes, I was actually asking how do you set the default gateway address on the DHCP server?,
    I believe I got the answer below:
    To configure the DHCP default gateway option Click Start, point to Administrative Tools and then click DHCP. In the console tree, expand the applicable DHCP server, expand IPv4, and then right-click Scope Options Click Configure Options, check 003
    Router, type the applicable Server name and IP address, and then click OK.
    Thank you

  • How to setup QoS for IP/Mac Address WRVS4400N

    I need some help setting up QoS for two Cisco/Linksys devivces on my network. 
    Network devices are Comcast SB6120 modem into WRVS4400n (v2.0.2.1 firmware) that divides into one 24 port gigabit Netgear unmanaged switch, 1 port into AT&T Cisco Microcell, 1 port to HP Officejet 7700 wired printer.  Unmanaged switch has approx 10 devices attached (including another 8 port unmanaged gigabit switch).  3 static leases are defined for the network for three devices (HP OJ 7700 printer, Cisco/Linksys PAP2 VOIP adapter, windows home server v1.  DHCP is handled by WRVS4400n.  Comcast service provides 12mbps of service upstream, 4mbps downstream.
    Need to setup QoS for AT&T Microcell and PAP2 VOIP adapter.  The real issue that I can't figure out how to configure is IP based priority access.  I can do rate control for an IP address but can't figure out how to specify priority control for an IP.
    Here are my the current config questions:
    1.  Bandwidth management page:  For the microcell device plugged into port 1, do i set the default CoS to 4 or 1?
    2.  Bandwidth management page:  Should the bandwidth management type be set to priority?  I assume yes since I need to define the UDP/TCP ports for priority.  The major issues here are
    a) one of the ports the Microcell uses is secure https (TCP 443) which is could also be used by any other internet device. 
    b) can't specify priority for the PAP2, since it's behind the unmanaged 24 port switch
    3.  QoS setup page:  Do I need just 2 queues (one for the port ID for the Microcell and one for the IP address of the Linksys adapter)?
    4.  QoS setup page:  I assume I need to define DSCP for the unmanaged switch but not sure how to tie a queue to an IP address
    4.  QoS setup page:  Shoud priority 0 be set for the most important queue (microcell) and the priority 1 CoS be for the VOIP adapter?  Again, not sure about how to define priority by IP address.
    5.  DSCP setup page:  As far as I can find, there's no documentation on how to setup this page.   

    That's what I do. I keep it simple, one calendar, one set of contacts.
    iCloud is really the simplest way to go, as it will sync your (eventual) single Contacts and Calendar across all your devices.
    I would:
    Figure out which single calendar (in Calendar.app) and contacts (in Contacts.app) that you want to keep.
    I'd make a backup of each one. For example,
    in Contacts, File > Export... > Contacts Archive...
    in Calendar, File > Export... > Calendar Archive...
    Make a backup of the other calendar events and contacts that you want to save.
    delete all the contacts and calendars from your phones and your iPad.
    add the contacts and events from the backups to the single calendar in Calendar.app and your contacts in Contacts.app on your iMac. There is probably some way to export the contacts and events you are adding, and then combine them, but you could also just add them manually.
    Then when you configure all your devices for iCloud, they will be all synced automatically.
    Message was edited by: arthur

  • How to setup the From header  in fullname and email address format

    when I sent mail from the messaging express , the mail that I sent cannot show the sender in the fullname and email address format. I use webmail and other mail client . It show only email address. I don't know how to setup this . I use the SUN JES messaging server 6.0 SP1 .

    exactly so.
    in general, for any configutil setting:
    0=off=no
    1=yes=on

  • How can we get Sun Ray DHCP address in Windows XP?

    We need the DHCP address (served by Windows) of our Sun Rays as a variable in our Windows XP session (served by VDI 3 / vBox 2.0.10). Customer wants to use this for a windows script which maps the room printer to the Sun Rays Windows XP session. So the user can get always the room printer automatically mapped as the default and don't need to choice the right printer. How can we do this and will this work wor hotdesking too?

    currently you can not use SGD and Sun VDI on dual monitors. There is a Request for Feature Enhancement to provide this feature in a future version.

  • How can I synch the Address Book on my Mac to the Contacts on my iPad (or, can I setup Address Book on my iPad?)

    How can I synch the Address Book on my Mac to the Contacts on my iPad (or, can I setup Address Book on my iPad?)

    Selected under the Info tab for your iPad sync preferences with iTunes.
    With such a question, you should spend some time with the user guide.
    http://manuals.info.apple.com/en/ipad_user_guide.pdf

  • RVS4000 won't get WAN DHCP address

    I just tried replacing a cheap domestic router/switch with an RVS4000 V2 on our work network.  This has a WAN connection to a cable modem for internet access via a dynamic IP address.
    When I first connected the RVS4000 it got a WAN ip address via DHCP of 192.168.100.11.  This is the type of IP address we get when there is an upstream problem with our ISPs cable network, and sure enough we had no internet access.  The RVS4000 was set to use DHCP on the WAN interface.  So I logged a support call with our ISP but they said there were no problems at their end.
    I then swapped the RVS4000 out for the original router.  This worked fine and got a WAN DHCP address of 77.xxx.yyy.zzz as it should.  Swapped back to the RVS4000 and back to the same problem of getting a 192.168... address.
    So, I downloaded the latest firmware from Cisco, which was V2.0.3.2 and flashed the RVS4000.
    I then tried again connecting the RVS4000 to the cable modem but this time it would not get any WAN DHCP address at all.  On the Status/Gateway page of the web interface it said that the WAN interface was down.  However, on the front panel there was a yellow light indicating a live connection on the internet port.
    Any suggestions?  I am assuming there must be a fault, but thought I would check for advice before sending it back.

    Hi Nick,
    Connect your computer directly to the modem, obtain the right IP address. Then put the RVS4000 back to the modem connection. Go to the set up, MAC ADDRESS CLONE, Enable this feature then use the option "clone my pc mac".
    Then wait 1-2 minutes and refresh the WAN.
    Basically this feature puts your computer's MAC on the router WAN interface. You can also use the previous router's WAN MAC if you know it and want to manually type it in.
    -Tom

  • How to setup spotlight to ignore safari history item. I just want bookmarks

    Anybody know how to setup Spotlight so that when I do a search, it just finds bookmarks? I don't want all of the history items.
    Thanks to all who answer.
    Mark

    You can check if you have a user.js file in the profile folder to initialize some prefs each time you start Firefox.
    The user.js file is only present if you or other software has created it, so normally it wouldn't be there.<br />
    You can check its content with a plain text editor if the file is there and you didn't create this file yourself.
    The user.js file is read each time you start Firefox and initializes preferences to the value specified in this file, so preferences set via user.js can only be changed temporarily for the current session.
    *http://kb.mozillazine.org/Preferences_not_saved
    You can do a search for delta search pref on the <b>about:config</b> page and reset related user set (bold) prefs via the right-click context menu to the default value.

  • How do I get a new DHCP address?

    I work in television, and we travel to a new location each week. Our Network is run through NomadixAG3000, and, anyone with a PC doesnt seem to have any issues logging on to our network. There seems to be new Mac users every other week, and the problems are escalating... For some reason, Macs seem to hold a DHCP address, I don't need to Renew my DHCP lease, I need a NEW DHCP lease. I just found a new error message, telling me the address is in use. I can't seem to get the computer to search for a different address. When I log on in MY work area, it is to a wireless access point/router , with encryption, so there doesnt seem to be any competition for these addresses. I work closely with our IT guys, but not in IT, and while I am completely ignorant as to System Administration, as a Mac User out here, I'd like to know the hows and whys to the problem.
    UPDATE: Every MAC, not just mine, seems to be trying to access the network to the SAME address, and once it's taken, we get an error message saying the 10.10.23.97 address is taken. I'm pretty sure the problem is with the Network System Admin settings. I log on without any issues on many other Nomadix based systems in hotels/coffeeshops, etc. Anyone see a clue here?

    BklynMoonshiner,
    I think you are on the right track with your suspicion that this is a router/hosting problem, not a Mac (OS X) problem. What is interesting is that all OS X machines are either attempting to acquire- or are being offered- the same IP address. This may be the clue you need to figure this out.
    Off the top of my head, the only thing that comes to mind, the only thing that would be common to the OS X machines but not necessarily a PC, is that they are also attempting to configure IPv6. Your infrastructure may not be capable of IPv6, or it may not be configured to support it. Since all of the OS X clients would be attempting to configure it, they might all end up asking for or getting the same IP address. I think the latter is more likely; not able to process the IPv6 requests, the router/host simply defaults to a single IP address, instead of granting addresses dynamically.
    I'm just guessing, and I'm no IT guru by a long shot. The networking stack seems like a bad nightmare to me. However, I think it is worth a try to disable IPv6 and see if it changes anything. Open System Preferences>Network. Open the padlock, if necessary, then click the "Advanced..." button with your Airport connection selected. Switch to the "TCP/IP" tab, and use the pull-down menu to turn IPv6 off. Save your settings, then try reconnecting to the network. Do this with at least 2 or 3 OS X clients, and test them on the same access point.
    Scott

  • How can local & Hreap attached clients get the correct DHCP address

    I am going to have a single private SSID that can be used by clients in our local AP's office and by h-reap clients on AP's in the foreign offices.
    All clients will authenticate via a radius server but how do I ensure that the local and remote clients will be given a dhcp address from their relevant local dhcp server?
    What setting are required to ensure this happens.
    I require Cental Authentication and local switching.
    I have a 2112 WLC and 1131LWAP's
    Thanks in advance
    Richard

    You just have to have a dhcp server listening wherever you're putting the clients.  You can change which vlan a ssid is mapped to on a per-AP basis.  So if your remote office uses vlan 50 for workstations you just need to change the vlan mappings for the AP(s) to 50, then make your AP port a trunk on whatever switch you're plugging into.  Then as long as you have a dhcp server listening on that AP, clients will get an IP from it.

  • How to setup a static IP for a wireless printer

    This problem has been ongoing for several versions of OS X and the last five printers I've had and I'm finally over messing with it.  For some reson, when using a wireless printer with OS X this is a repetetive problem, and I think if I configured the printer to a static IP address instead of using DHCP, it might work better.  At least once a week, if not more often, I'll print something and get the ubiquitous Dock error of "Printer is not connected".  The printer is still in Preferences, but if I delete it, then it doesn't show up as it should for selection.
    The only way to fix this is reboot, and then the printer shows up again in Preferences.  I select it and all is well again...until a few days pass and the same thing happens again.  Using an HP LaserJet P1102w, still a current model, but it doesn't matter which printer I use.  I also have an Epson Artisan 725 and the same thing happens with it about once a week.  Also, this happens from both my Mac and my wife's Mac, so it's not an issue with just my machine.
    I've searched for documentation on how to setup a static IP address for a wireless printer with the Airport Extreme, but all I find are tutorials on how to do it with an ethernet hard-wired printer.  Any help would be greatly appreciated.

    You could set up your router to do manual assignment of IP address instead of using DHCP, but that is a PITA, because then you'd have to manually set up IP for all your devices.
    If you have AirPOrt Extreme, you could do this:
    In your Apple TV, go to the Settings >> About and write down the MAC address of your ATV
    Start up the AiPort Admin Utility
    Go to Network tab
    click + in the DHCP reservations
    Choose an IP you want for your ATV & Enter the MAC address
    From now on, this IP address will be reserved to the MAC address and only your ATV will be able to get it, no other device will.
    It is not a static IP in a true sense, but behaves just like one.
    Works great for me...
    If you don't have a AP Extreme, I'm sure other routers will allow you do reservations too.

Maybe you are looking for

  • How can I get a real person to look at my IP Profi...

    My current saga started 4 days ago when a BT van was spotted in the village. This is usually a bad sign as it means a BT engineer is about to break a random number of people's broadband connections. Quite why they feel the need to do this is beyond m

  • Statistics of Sync and Async messages in PI

    Hi, How can we count no of Sync and Async messages that were processed(sucessful or unsucessful) in PI. Does the worbench has any table or Report that will give me the statistics. Request some pointers on the same. Thanks , Bhanu.

  • HTTP GET only works once

    Web UI Builder: I have a device that responds to HTTP GET messages. I made a simple vi that uses the HTTP GET String function connected to a string constant and WireShark to monitor Ethernet traffic. When the vi is first run an HTTP message is sent a

  • Web Center Server language

    When I access the Web Center Server the used language is Italian while I would like it is English. Can anyone to explain me where and how to set the preferred language? Thank you in advance!

  • Mozilla products not working after update

    Hello, after update (about 4 weeks ago) irefox and Thunderbird didn't want to start. I tried reinstalling but it didn't help. When I run it, there is no error in the console and the processes have started, but no windows appears. I'm on 64bit Arch. A