Satellite M30-801 - display will not work after hibernation

Hello everybody,
I hope you will help me with this issue. I have a Toshiba Satellite M30-801 and my warranty has finished.
A few days ago, my computer had stayed some hours in standby mode. When I restarted the system, the screen continued on black. No images.
I connected an external monitor to check the video card and that test was ok. Now I'm writing this letters using my laptop connected to the external monitor.
Also, i noticed that there was blacklight on the screen.
I had checked the power management for the universal serial bus controllers on the control panel.
I downloaded and installed the last bios update.
But the display is still black.
Could you help me? any ideas?
Thanks and regards,
Stalker99ES

Hello Sascha,
++When you start your notebook without external monitor can you see anything?+
> > No. I can't see anything at all. I only can "see" the backlight of the screen. But no images.*
++When you use external monitor what happen when you try to change display mode using FN+F5 key combination?,++
> > Only two things: The external monitor goes to standby mode (when i don't use crt combination) and backlight dissapear, so the notebook screen goes to off mode.
> > Nothing more.
> > I hope you could help me.
> > Thanks and regards,

Similar Messages

TS1702 Certain apps will not work after ios6 install.

Certain apps will not work after ios6 update. Tiger Woods golf will run for about 5 seconds and stop. Have uninstalled/re-installed to no avail.

My husband had the same problem with some apps after I updated his iPad 2 to iOS 5. I checked the app store and there were updates for the apps to support the new software. After updating, all apps work just fine.

HT1338 motion 4 will not work after yosemite upgrade

motion 4 will not work after yosemite upgrade

To be honest I do not use motion or any other compositing app so i do not miss it personally. However the new Motion is not that expensive, around $60 i think. Still, I understand your frustration.
I am afraid the more the OS is updated the less compatible certain applications will become.
Good Luck
h

My iPod touch 4G will not work after I tried to Downgrade it from iOS 5 to iOS 6

My iPod touch 4G will not work after I tried to Downgrade it from iOS 5 to iOS 6. The screen is black and it doesn't work.

Downgrading the iOS is not supported by Apple.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Glide pad will not work after formatting g60-630ca

Can somebody help? my glide pad will not work after downgrading to xp. The pad works itself for the mouse but then the scrolls on the side will not. Please help...

You need the driver. It is a Synaptics Touchpad and you can use this driver:
Synaptics
Here is a link to the General XP Downgrade guide which has a link to all the drivers you need under "Moderate models:
XP Guide
The touchpad is hard because Windows does load a basic driver so it does not appear with an error in Device Manager, but the "real" driver is needed for advanced features like scrolling. Be sure you have all the needed Xp drivers, by the way.

HT1414 wifi will not work after restore

wifi will not work after restore

Se emy response to your other post
https://discussions.apple.com/thread/4862098?tstart=0

Telephone will not work after installing fax wizard

I have a new HP Office Pro 8615. After I installed the fax wizard, my telephone quit receiving or sending calls. The only incoming call will ring on the fax. Can I uninstall the fax, as I do not need it?

Hi , Welcome to the HP Forums! I see that your telephone will not work after installing fax wizard, for your HP Officejet Pro 8615. I am happy to help! What is the Operating System you are using? Windows or Mac? What version? If you do not know the Operating System you are using, please visit this website. Whatsmyos. If you do not need the fax, all you should have to do is unplug the phone cable from the back of the printer. That will prevent the printer from using the fax function. If your phone continues not to work, I would consider contacting your phone provider. Thank you for posting! “Please click the Thumbs up icon below to thank me for responding.”

OMiC will not work after installing Leopard

Does anyone know why OMiC will not work after upgrading to Leopard?
After downloading Leopard, went into mail and tried to open a windat file, but a message came up stating OMiC disabled. I deleted that version, and tried to download OMiC 1.7.7 but it won't even get thru the download menu, it stops at "installation" gives me a choice of Tiger, or Panther, and it will not let me go any further. Has this happened to anyone else???

I am not sure any of the solutions for these files have been made Leopard compatible -- I saw another post about this not long ago. See:
http://discussions.apple.com/thread.jspa?messageID=5736631&#5736631
Ernie

My Keyboard and touch-pad will work during post, but will not work after the os loads?

I have a G60 and My Keyboard and touch-pad will work during post, but will not work after the os loads? Im running Windows 7, Anyone have any Ideas? I have already tried a hard reset, and safe mode???

Try pressing the fn key and f2 to reach bios
or
try a usb mouse from your desktop
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Satellite P305-S8820 - FN key not working after clean install of Windows 7

Hi,
I have a Toshiba Satellite P305-S8820. I recently did a clean install of Windows 7. I have loaded the Toshiba value added driver pack and the trackpad driver but still cannot get the trackpad or the FN key to work.
Any ideas?

Hello John
You are like other millions other users and what you can read is relevant for you but sometimes it works a little bit different. For you it can be useless but sometimes it helps. Fact is that this utility is offered for some notebook models.
Generally speaking you are right and after VAP installation the job should be done but Ive faced the same problem in the past. Sometimes it works well and sometimes not. You will not believe me but in the past I used stuff for Satellite P300 to get all stuff working on Satellite A350. I cannot explain why this happen and it sounds crazy but it is the truth.
You can also try to play a little bit with VAP installation. Try to install VAP for A300/A350/P300. Generally speaking it is the same and if this will not work well you can remove it from the system.
Launcher for flash cards? It must be listed in MSCONFIG > startup > TcrdMain.exe

Touchsmart 520-1047c Mouse and Keyboard will not work after sleep mode

I have an issue which I need some help with. When my computer goes to sleep the wireless mouse and keyboard will not work unless I restart, however each one will wake the system up but will not operate after that. I have tried just making the display go to sleep, both go to sleep but that makes no difference same issue occurs. The only work around I have found is going into the power settings and turning the sleep mode off for booth the computer and display. This does not solve the problem it just masks it. New batteries, unplugged and replugged the dongle, updated the bios and all drivers. Don't know what else to try. Anybody know how to fix this? Thank you in advance for your help.

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I understand that the mouse and keyboard on your desktop computer does not work if your computer enters sleep mode, and I would be happy to assist you in this matter! To correct this issue, I recommend following the steps in this document on Troubleshooting sleep and hibernate issues (Windows 7). This should help enable your system to wake from sleep mode using your wireless keyboard and mouse. I also recommend connecting wired peripherals to diagnose the functionality of your keyboard and mouse. If your system is still not able to wake from sleep mode, please follow the steps below to restore the default power schemes on your computer: Step 1. Click the Start button
Step 2. In the search box, type "Command Prompt"
Step 3. Right-click Command PromptStep 4. Click Run as administrator
Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
Regards

G4-450 DP with a 22 inch clear Cinema display will not work, please advise

Hello all
I can not seem to get a G4-450 DP to work with a 22 inch clear Cinema display, i even have one of those dr.botts wich i normaly run a 2nd 15" clear display.
What happens is that it starts up and then goes black,
can anyone advise?

Hi-
Could you check your system profiler for graphics, and post the model of the card that you have? The stock card is the Rage 128 with the following specs:
-ATI RAGE 128 Pro graphics card with 16MB of SDRAM graphics memory installed in a dedicated AGP 2X graphics slot
-Support for up to 1920– by 1200–pixel resolution at 32 bits per pixel (millions of colors)
-Apple Display Connector (ADC); carries analog and digital video, USB, and power
-15–pin mini D–Sub VGA connector
You say you have a DVI port (along with ADC) so, I want to clarify the card model.
You also state that the display worked once- in what configuration? Connected alone? Through the Dr. Bott's DVIator? That means from the DVI port to an ADC connector on the screen (but the 22" is a DVI connection)?
I found the following quote on the Dr. Bott's page:
However, the ATI Rage 128 card will not work with the 20", the 22" and the 23" Cinema Displays
To clear up confusion (mine), please carefully check your profiler, compare the ports of your card to the Display compatibility link (in above post), and let me know the results (what you have), along with a description of what connects to what. A model number for the display would also help.
Generally speaking, when a display goes black after the gray screen, the graphics card isn't compatible, or the necessary software/drivers are not installed.
G4AGP(450)Sawtooth, 2ghz PowerLogix, 2gbRAM, 300gbSATA+160gbATA, ATI Radeon 9800 Mac OS X (10.4.8) Pioneer DVR-109, ExtHD 160gb x2, 23"Cinema Display, Ratoc USB2.0, Nikon Coolscan

Printer will not work after update to Mavericks

I have a macbook pro and an HP7280 printer connected wirelessly. After upgrading to Mavericks the printer will not work. The first time I used it the system upgraded automatically (I forget what it said but it just went ahead and did some upgrading) When I clicked on something to print it did recognized the printer but just scrolled and scrolled and never printed. So I deleted the printer and reset the system and then added the printer back on - same thing. Any ideas??

It means there is no issue with the driver you are using and with it working correctly on Mavericks. So you have a network issue with the printer queue you are using. Normally a reset of the printing system and re-adding the printer would be enough to get things working again. But since you have done this and your issue is not resolved, there must be some other gremlins in the system.
With the HP connected to the network, if you know its IP address you can enter this as a URL into a web browser. This should result in you connecting to the internal web page of the HP. Does this work?

ITunes PLAY/PAUSE Will Not Work After 10.5.4 Install

I have just installed Leopard 10.5.4 on my iMac G5 and iTunes player will not work. When I select a song, it will show in the player window, but, PLAY/PAUSE button will not function. I have checked iTunes Prefs and see nothing there that is not correct. I am able to navigate throughout iTunes and everything seems to work as before EXCEPT Play/Pause. (Actually, I don't know about PAUSE since I cannot get PLAY to work).
???????????

Raymond Rogoway wrote:
Used Software Update to update to 10.5.1. Now my install disk will not boot. Drive kicks out disk after awhile. Ran Disk Warrior which reported no changes. Repair permissions.
Ray
Does the disk also get ejected when you are running Leopard, or only when using it for booting?
Have you looked at it physically for scratches or that dirty film some DVDs had?

Iphoto will not work after uploading yosemite

After uploading the Yosemite upgrade. The iPhoto will not work. I have done what the software recommends. I have deleted the app and reloaded it. I get the same message. The message that i get is:
your photo library is either in use by another application or has become unreadable.
shut down and restart your computer and then open iPhoto again. if the problem persists. try rebuilding your photo library. to do this quit iPhoto, and then reopen it while keeping the option and command keys pressed. you can also try restoring your photo library from a backup.
Any suggestions or help would be greatly appreciated.
Matt

Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.

Satellite M30-801 - display will not work after hibernation

Similar Messages

Maybe you are looking for