SCOM agent install fails Error 80070035 - the network path was not found
I have deployed SCOM 2012 agents to most servers (2008, 2008 R2, 2012, 2012R2) in our estate but some either fail to install or are not monitored. I assume the two problems are related, but for now I am concentrating on the servers that fail completely.
Installation is from the Discovery Wizard and I have about 20 servers that fail of various server versions.
So looking at one specific server that is failing to install the agent - a 2008 standard service pack 2
The firewall in on and file and printer sharing is enabled for domain, remote administration is enabled for domain
I added a specific rule to allow TCP 5723 and 5724
DCOM is enabled
I can Ping the target server from the SCOM server by both name and FQDN - both return the same IP and our DNS server has only one entry for this server
I can browse to the admin share \\server\C$ from the SCOM Server, using the same account that I specify for the agent install that is a domain admin with rights on this server (and on the other servers the agent
did install to) and the server has plenty of disk space available
I am not sure what else to look at so would welcome any ideas
Thanks
Hi Petro,
I have a Agent installation failure cheat sheet, For your error 80070035 it is said to perform a manual installation.
So i would like to understand which version of SCOM is this ? 2007 R2 or 2012 or 2012 r2 ?
Also check if your agents have the WMI service started and enabled ?
Also if yours is a SCOM 2007 R2 do you have a RMS & MS in your management group ? If yes then Pushing the agent installation from MS may cause such issue. So would suggest you push the installation from RMS.
Also check if your Network connectivity meets the minimum requirement as recommended by SCOM. Below is applicable for Both SCOM 2007 R2 & SCOM 2012 & 2012 R2.
Component A
Component B
Minimum Requirement
Root management server or management server
Agent
64 Kbps
Root management server or management server
Agentless
1024 Kbps
Root management server or management server
Database
256 Kbps
Also check if you have any Anti virus / Firewall which is blocking the install / communication. If yes disabe or add the "Monitoringhost.exe to the safe list or what your feature is.
Check if you have another IP assigned to the NIC card and remove it tempraurly andchecl.
Also post the event logs of the Agents which are in not monitored state for analysis.
SCOM Agent installation failure error codes
Error
Error Code(s)
Remediation Steps
The MOM Server could not execute WMI Query "Select * from Win32_Environment where
NAME='PROCESSOR_ARCHITECTURE'" on computer server.domain.com
Operation: Agent Install
Install account: domain\account
Error Code: 80004005
Error Description: Unspecified error
80004005
1. Check the PATH environment variable. If the PATH statement is very long, due to lots of installed third party software - this can
fail. Reduce the path by converting any long filename destinations to 8.3, and remove any path statements that are not necessary.
2. The cause
could be corrupted Performance Counters on the target Agent.
To rebuild all Performance counters including extensible and third party counters in Windows Server 2003, type the following commands at a command
prompt. Press ENTER after each command.
cd
\windows\system32
lodctr /R
Note /R is uppercase.
Windows Server 2003 rebuilds all the counters because it reads all the .ini files in the C:\Windows\inf\009 folder for the English operating system.
How to manually rebuild Performance Counter Library values
http://support.microsoft.com/kb/300956
3. Manual agent install.
The MOM Server could not execute WMI Query "Select * from Win32_OperatingSystem" on
computer “servername.domain.com”
Operation: Agent Install
Install account: DOMAIN\account
Error Code: 800706BA
Error Description: The RPC server is unavailable.
8004100A
800706BA
1. Ensure agent push account has local admin rights
2. Firewall is blocking NetBIOS access
3. Inspect WMI health and rebuild repository if necessary
4. Firewall is blocking ICMP (Live OneCare)
5. DNS incorrect
The MOM Server failed to open service control manager on computer "servername.domain.com". Access is Denied
Operation: Agent Install
Install account: DomainName\User Account
Error Code: 80070005
Error Description: Access is denied.
80070005
80041002
1. Verify SCOM agent push account is in Local Administrators group on target computer.
2. On Domain controllers will have to work with AD team to install agent manually if agent push account is not a domain admin.
Disable McAfee antivirus during push
The MOM Server failed to open service control manager on computer "servername.domain.com".
Therefore, the MOM Server cannot complete configuration of agent on the computer.
Operation: Agent Install
Install account: DOMAIN\account
Error Code: 800706BA
Error Description: The RPC server is unavailable.
800706BA
1. Firewall blocking NetBIOS ports
2. DNS resolution issue. Make sure the agent can ping the MS by NetBIOS and FQDN. Make sure the MS can ping the agent by NetBIOS
and FQDN
3. Firewall blocking ICMP
4. RPC services stopped.
The MOM Server failed to acquire lock to remote computer servername.domain.com. This means there is already an agent management operation proceeding
on this computer, please retry the Push Agent operation after some time.
Operation: Agent Install
Install account: DOMAIN\account
Error Code: 80072971
Error description: Unknown error 0x80072971
80072971
This problem occurs if the LockFileTime.txt file is located in the following folder on the remote computer:
%windir%\422C3AB1-32E0-4411-BF66-A84FEEFCC8E2
When you install or remove a management agent, the Operations Manager 2007 management server copies temporary files to the remote computer. One
of these files is named LockFileTime.txt. This lock file is intended to prevent another management server from performing a management agent installation at the same time as the current installation. If the management agent installation is unsuccessful and
if the management server loses connectivity with the remote computer, the temporary files may not be removed. Therefore, the LockFileTime.txt may remain in the folder on the remote computer. When the management server next tries to perform an agent installation,
the management server detects the lock file. Therefore, the management agent installation is unsuccessful.
http://support.microsoft.com/kb/934760/en-us
The MOM Server detected that the following services on computer "(null);NetLogon" are not running. These services are required for push
agent installation. To complete this operation, either start the required services on the computer or install the MOM agent manually by using MOMAgent.msi located on the product CD.
Operation: Agent Install
Remote Computer Name: servername.domain.com Install account: DOMAIN\account
Error Code: C000296E
Error Description: Unknown error 0xC000296E
C000296E
1. Netlogon service is not running. It must be set to auto/started
The MOM Server detected that the following services on computer
"winmgmt;(null)" are not running
C000296E
1. WMI services not running or WMI corrupt
The MOM Server detected that the Windows Installer service (MSIServer) is disabled on computer "servername.domain.com". This service is
required for push agent installation. To complete this operation on the computer, either set the MSIServer startup type to "Manual" or "Automatic", or install the MOM agent manually by using MOMAgent.msi located on the product CD.
Operation: Agent Install
Install account: DOMAIN\account
Error Code: C0002976
Error Description: Unknown error 0xC0002976
C0002976
1. Windows Installer service is not running or set to disabled – set this to manual or auto and start it.
The Agent Management Operation Agent Install failed for remote computer servername.domain.com.
Install account: DOMAIN\account
Error Code: 80070643
Error Description: Fatal error during installation.
Microsoft Installer Error Description:
For more information, see Windows Installer log file "C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameAgentInstall.LOG
C:\Program Files\System Center Operations Manager 2007\AgentManagement\AgentLogs\servernameMOMAgentMgmt.log" on the Management Server.
80070643
1. Enable the automatic Updates service…. Install the agent – then disable the auto-updates service if desired.
Call was canceled by the message filter
80010002
Install latest SP and retry. One server that failed did not have Service pack installed
The MOM Server could not find directory \\I.P.\C$\WINDOWS\. Agent will not be installed on computer "name". Please verify the required
share exists.
80070006
1. Manual agent install
Possible locking on registry?
http://www.sysadmintales.com/category/operations-manager/
Try manual install.
Verified share does not exist.
The network path was not found.
80070035
1. Manual agent install
The Agent Management Operation Agent Install failed for remote computer "name". There is not enough space on the disk.
80070070
1. Free space on install disk
The MOM Server failed to perform specified operation on computer "name". The semaphore timeout period has expired.
80070079
NSlookup failed on server. Possible DNS resolution issue.
Try adding dnsname to dnssuffix search list.
The MOM Server could not start the MOMAgentInstaller service on computer "name" in the time.
8007041D
80070102
NSlookup failed on server. Possible DNS resolution issue.
Verify domain is in suffix search list on management servers.
The Agent Management Operation Agent Install failed for remote computer "name"
80070643
1. Ensure automatic updates service is started
2. Rebuild WMI repository
3. DNS resolution issue
The Agent Management Operation Agent Install failed for remote computer "name". Another installation is already in progress.
80070652
Verify not in pending management. If yes, remove and then attempt installation again.
The MOM Server detected that computer "name" has an unsupported operating system or service pack version
80072977
Install latest SP and verify you are installing to Windows system.
Not discovered
Agent machine is not a member of domain
Ping fails
1. Server is down
2. Server is blocked by firewall
3. DNS resolving to wrong IP.
Fail to resolve machine
1. DNS issue
The MOM Server failed to perform specified operation on computer "name". Not enough server storage…
8007046A
1. This is typically a memory error caused by the remote OS that the agent is being installed on.
There are currently no logon servers available to service the logon request.
8007051F
1. Possible DNS issue
This installation package cannot be installed by the Windows Installer service. You must install a Windows service pack that contains a newer version
of the Windows Installer service.
8007064D
1. Install Windows Installer 3.1
The network address is invalid
800706AB
Possible DNS name resolution issue.
Tried nslookup on server name and did not get response.
Verify domain is in suffix search list on management servers.
The MOM Server failed to perform specified operation on computer servername.domain.com
80070040
1. Ensure agent push account has local admin rights
The MOM Server detected that the actual NetBIOS name SERVERNAME is not same as the given NetBIOS name provide for remote computer SERVERNAME.domain.com.
80072979
1. Correct DNS/WINS issue.
2. Try pushing to NetBIOS name
Gautam.75801
Similar Messages
-
Updating hybrid configuration failed - Kerberos authentication: The network path was not found
I'm configuring Exchange 2010 SP3 as a Hybrid server with Exchange Online. This is a single server running Exchange roles Mailbox, Client Access, Unified Messaging and Hub Transport.
When I run the Manage Hybrid Configuration, I receive the following error:
Updating hybrid configuration failed with error
'System.Management.Automation.Remoting.PSRemotingTransportException: Connecting to remote server failed with the following error message : WinRM cannot process the request. The following error occurred while using Kerberos authentication: The network
path was not found.
The full text from the Hybrid Configuration log file (C:\Program Files\Microsoft\Exchange Server\V14\Logging\Update-HybridConfiguration)
[1/5/2014 21:21:1] INFO:Opening runspace to
http://[servername]/powershell?serializationLevel=Full
[1/5/2014 21:21:1] INFO:Disconnected from On-Premises session
[1/5/2014 21:21:1] ERROR:Updating hybrid configuration failed with error 'System.Management.Automation.Remoting.PSRemotingTransportException: Connecting to remote server failed with the following error message : WinRM cannot process the request. The following
error occured while using Kerberos authentication: The network path was not found.
Possible causes are:
-The user name or password specified are invalid.
-Kerberos is used when no authentication method and no user name are specified.
-Kerberos accepts domain user names, but not local user names.
-The Service Principal Name (SPN) for the remote computer name and port does not exist.
-The client and remote computers are in different domains and there is no trust between the two domains.
After checking for the above issues, try the following:
-Check the Event Viewer for events related to authentication.
-Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use HTTPS transport.
Note that computers in the TrustedHosts list might not be authenticated.
-For more information about WinRM configuration, run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic.
at System.Management.Automation.Runspaces.AsyncResult.EndInvoke()
at System.Management.Automation.Runspaces.Internal.RunspacePoolInternal.EndOpen(IAsyncResult asyncResult)
at System.Management.Automation.Runspaces.RunspacePool.Open()
at System.Management.Automation.RemoteRunspace.Open()
at Microsoft.Exchange.Management.Hybrid.RemotePowershellSession.Connect(PSCredential credentials, CultureInfo sessionUiCulture)
at Microsoft.Exchange.Management.Hybrid.Engine.Execute(ILogger logger, String onPremPowershellHost, PSCredential onPremCredentials, PSCredential tenantCredentials, HybridConfiguration hybridConfiguration)
at Microsoft.Exchange.Management.SystemConfigurationTasks.UpdateHybridConfiguration.InternalProcessRecord()'.
I have sought help, posting on the forum at community.office365.com -
http://community.office365.com/en-us/forums/158/t/212265.aspx. But I've got to a point where I believe the problem is more to do with how PowerShell is operating on the on-prem Exchange server.
Has anyone else come across this problem running the Hybrid Configuration Wizard?Hello Darrell,
Have you verified the settings of Powershell virtual directories for the on-premises Exchange Servers? The following article has a list of some common issues with that virtual directory and how to correct them:
http://technet.microsoft.com/en-us/library/ff607221(v=exchg.80).aspxI would take a look at the one titled "Configure Kerberos Authentication" specifically to ensure everything
looks good.
As the article states you can run the Exchange BPA and it will check if any of these exist as well. -
Peer to Peer network error 0x80070035 the network path was not found
We are adding an XP computer to a peer to peer network with Vista machines. The Vista machines can see the XP machine in the network but when clicking to get to share files, message comes up Windows cannot access \\XPcomputer. The message adds that there may be a spelling error or that there may be a problem with the network. But the error message is the one listed in the subject of this email.
XP machine is properly set to share folders and there is no other visible proble. There is no message from the antivirus software so I am assuming the address is within the Antivirus acceptable range. Antivirus is Norton 360.
Any suggestions...very frustrating... thank youHi,
Before we start, please access the following article. This KB article introduces our support policies for peer-to-peer network
Using Crossover Cables in Home or Peer-to-Peer Networks
http://support.microsoft.com/default.aspx?scid=KB;EN-US;278870
The error code 0x80070035 indicates that the network path is not found. This behavior occurs if the NetBIOS over TCP IP is not enabled in Windows Vista. Please follow the steps below.
1. Click "Start", input "NCPA.CPL" (without quotation marks) and press Enter.
2. Right click on the connection that you use for the local connection, and then click "Properties".
3. Click Continue button to verify the administrator permission.
4. Click to select "Internet Protocol Version 4 (TCP/IPv4)", and then click "Properties".
5. Click "Advanced" button in the open window. On the "WINS" tab, click to select "Enable NetBIOS over TCP/IP", and then click "OK" to save the setting.
The following article introduces NetBIOS over TCP/IP
NetBIOS over TCP/IP
http://technet.microsoft.com/en-us/library/bb727013.aspx
If the issue is not resolved, you may try to access the computer with \\[IP address] as a work around. -
SqlFileStream error: The network path was not found
I created a FileStream enabled table in a SQL2008 database, and populated some rows into it, from a SQL2000 table storing image. It's fine.
Then I wrote a WPF application in C#, trying to access the filestream data as below code snippet:
SqlConnection sqlConn = null;
SqlTransaction sqlTran = null;
try
// ids_static_imagesTableAdapter was defined by SQL SELECT statement:
// SELECT TOP (@x) image_name, image, image.PathName() AS image_path FROM dbo.ids_static_images
ids_static_imagesTableAdapter imgTa = new ids_static_imagesTableAdapter();
sqlConn = imgTa.Connection;
sqlConn.Open();
idsxi2011imageDataSet.ids_static_imagesDataTable imgDt = imgTa.GetData(10);
sqlTran = sqlConn.BeginTransaction();
SqlCommand cmdGetFsTxCtx = sqlConn.CreateCommand();
cmdGetFsTxCtx.CommandText = "SELECT GET_FILESTREAM_TRANSACTION_CONTEXT()";
cmdGetFsTxCtx.Transaction = sqlTran;
byte[] fileStreamTxCtx = (byte[])cmdGetFsTxCtx.ExecuteScalar();
foreach (idsxi2011imageDataSet.ids_static_imagesRow imgRow in imgDt)
SqlFileStream imgSqlFileStream = new SqlFileStream(imgRow.image_path, fileStreamTxCtx, FileAccess.Read);
Add(new ImageFile(imgRow.image_path, imgRow.image_name, imgSqlFileStream));
sqlTran.Commit();
finally
if (sqlConn != null && sqlConn.State == ConnectionState.Open)
sqlConn.Close();
The SqlFileStream constructor throws error, states 'The network path was not found'.
FYR, when I run the following SQL statement in SSMS:
SELECT TOP 1 image.PathName() AS image_path FROM dbo.ids_static_images
result as below:
\\XISERVER\MSSQLSERVER\v1\idsxi2011image\dbo\ids_static_images\image\3B121497-07E6-4568-9DDC-EFEAA57BE6AA
Any idea?Hi,
Could you please elaborate a bit? Are SQL Server 2008 and the WPF application running on separate machines? If so, I think we need to enable the
Allow remote clients to have streaming access to FILESTREAM data option.
Please see:
How to: Enable FILESTREAM
http://msdn.microsoft.com/en-us/library/cc645923.aspx
Please remember to mark the replies as answers if they help and unmark them if they provide no help.
Welcome to the All-In-One Code Framework! If you have any feedback, please tell us. -
The network path was not found
we have a windows server 2012 R2 as file server and we access the share location with DFS
however while accessing the file from share location sometimes the below error comes however after sometime again the error vanishes and the user is able to access the file
error is "The network path was not found"
other users are not having those error
user is having windows 7 enterprise
the below is the error found in the eventviewer at the same the above error is recieved by the user while accessing the share location
"Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2"
because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected."
Thank you
Viraj
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.Hi viraj,
Here is a KB article talking about the logged error:
Event ID 10 is logged in the Application log after you install Service Pack 1 for Windows 7 or Windows Server 2008 R2
http://support.microsoft.com/kb/2545227
The cause:
This originated in the Windows 7 SP1 DVD/ISO creation process. There was an issue in the creation process that caused a WMI registration to remain in the DVD/ISO. Since the registration is designed to work only during the DVD/ISO creation process, it fails
to run on a live system and causes these events. These events are not indicative of any issue in the system and can be safely ignored. If however you want to prevent these events from getting generated and want to remove this specific WMI registration manually,
please follow the steps mentioned in this article for running the workaround script.
Please run the Fix it Tool mentioned in the above article and see if issue insists.
Best regards
Michael Shao
TechNet Community Support -
Group Policy Object "The Network Path Was Not Found"
I should also mention even when I go to click on the currently created policies I get the same error as well, but I seem to be able to at least get into their settings if I wanted too.
Here is the my background of my network.Try to retire a Windows Server 2003 Domain Controller (DC) and upgrading to a Windows Server 2012 R2 domain controller. Currently both server are running as Domain Controllers on the same subnet.An issue I found today was when I went to go create a new group policy object I got an error stating "The Network Path was Not Found." This happens on both the 2003 and 2012 server, so it not just related to one machine. I have done some reading on this and it seems that some people who have a similar error have an issue browsing to their SYSVOL folder for the domain. However I have no issue browsing to that.I have also looked through the even viewer and there doesn't seem to be specific errors related to this. It seems to me like it may be some type of DNS issue, but I am looking for some insight into...
This topic first appeared in the Spiceworks Community -
I have two forests with a transitive on-way trust between them: PROD -> TEST (test trusts PROD). I had previously had kerberos authentication working with winrm from PROD to machines in TEST. I have verified the trust is healthy, I also verified users
in TEST can use WINRM with kerberos just fine. Users from PROD cannot connect via kerberos to machines in TEST with winrm.
I have verified the service has registered the appropriate SPNs. I ran dcdiag against all my PROD and TEST domain controllers and didn't find anything that would prevent kerberos from happening. I even tried disabling the firewall entirely on my TEST dcs
but that didn't gain me anything.
I've enabled kerberos logging but only see the expected errors such as it couldn't find a PROD SPN for the machine, which it shouldn't from what I understand, it should go to the TEST domain and find the SPN from there.
I'm really out of next steps before I call PSS and hope someone here has run into this and could provide me some next steps.
PowerShell Error:
Connecting to remote server failed with the following error message : WinRM cannot process the request. The following error occured while using Kerberos authentication: The network path was not found.
Possible causes are:
-The user name or password specified are invalid.
-Kerberos is used when no authentication method and no user name are specified.
-Kerberos accepts domain user names, but not local user names.
-The Service Principal Name (SPN) for the remote computer name and port does not exist.
-The client and remote computers are in different domains and there is no trust between the two domains.
After checking for the above issues, try the following:
-Check the Event Viewer for events related to authentication.
-Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use HTTPS transport.
Note that computers in the TrustedHosts list might not be authenticated.
-For more information about WinRM configuration, run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic.
+ CategoryInfo : OpenError: (:) [], PSRemotingTransportException
+ FullyQualifiedErrorId : PSSessionStateBroken
winrs Error:
Winrs error:
WinRM cannot process the request. The following error occured while using Kerberos authentication: The network path was not found.
Possible causes are:
-The user name or password specified are invalid.
-Kerberos is used when no authentication method and no user name are specified.
-Kerberos accepts domain user names, but not local user names.
-The Service Principal Name (SPN) for the remote computer name and port does not exist.
-The client and remote computers are in different domains and there is no trust between the two domains.
After checking for the above issues, try the following:
-Check the Event Viewer for events related to authentication.
-Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use HTTPS transport.
Note that computers in the TrustedHosts list might not be authenticated.
-For more information about WinRM configuration, run the following command: winrm help config.Hi Adam,
I'm a little unclear about which SPNs you were looking for, in which case could you confirm you were checking that on the computer object belonging to the actual destination host it has the following SPNs registered?
WSMAN/<NetBIOS name>
WSMAN/<FQDN>
If you were actually trying to use WinRM to connect to the remote forest's domain controllers, then what you said makes sense, but I was caught between assuming this was the case or you meant another member server in that remote forest.
Also, from the client trying to connect to this remote server, are you able to telnet to port 5985? (If you've used something other than the default, try that port)
If you can't, then you've got something else like a firewall (be that the Windows firewall on the destination or a hardware firewall somewhere in between) blocking you at the port level, or the listener on the remote box just isn't working as expected. I
just replied to your other winrm post with steps for checking the latter, so I won't repeat myself here.
If you can telnet to it and the SPNs exist, then you might be up against something called selective authentication which has to do with how the trust was defined. You can have a read of
this to learn a bit more about selective trusts and whether or not it's affecting you.
Cheers,
Lain -
Error Code 0x80070035 - The network path was not found, Windows Server 2008 SP2
I have bee receiving following "error code 0x80070035 - The network path was not found" when trying to open file shares in both directions using Windows Server 2008 Standard SP2 at both ends. The issue is identical to the KB article KB958285, however the hotfix is only valid up to but not including SP2. One of the servers in question has moved several times between 2 subnets seperated by a VPN. I have tried changing settings in and around the local NIC/DNS Suffix and in the network connection sharing centre, but with no luck. Firewalls are turned off at both sites, and pings and AD queries are successful (one server is a DC). DNS is also working correctly at both sites. Any help/suggestions would be appreciated.
RichardI thought I would add in another scenario, since this link came to the top of my list in the search engine.
We are running 2008 R2 with SP1 (it happened without SP1 as well)
We could not map using UNC (IP, FQDN, or netbios name). We could ping access the other servers via other utils like event viewer and services.msc but just could not map.
In our case it turned out to be a VMWARE issue but we still had to make a regedit change first
You have to go to regedit HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\NetworkProvider\Order\
And add LanmanWorkstation to Providerorder
I found on a Citrix board that citrix has an issue with this as well
If you're running VM here is an additional step you should do as well
When you upgrade VMware Tools installed with HGFS from ESX 3.x to ESX 4.x, the HGFS driver may not get uninstalled properly. In this case, the virtual machine's network Provider Order tab in Network Connections
> Advanced > Advanced Settings displays incorrect information and the virtual machine may lose network connectivity.
To avoid this issue, uninstall VMware Tools 3.x before installing VMware Tools 4.x.
To workaround this issue, if you have already upgraded VMware Tools:
Click Start >
Run, type regedit, and click OK. The Registry Editor window opens.
Navigate to
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\NetworkProvider\Order\.
Delete the reference to
hgfs.
Reboot the virtual machine.
We found that if you strip out the HGFS, you do not have to reboot for the provider order tab to come back
I hope that this saves people a lot of time. I spent days researching this.
This was the solution for me on 2008 R2 DC w/ Exchange. I do not have VMWare installed but do have Hyper-V. Thank you so much! -
Error code: 0x80070035 The network path was not found
"Error code: 0x80070035 The network path was not found" while trying to access another PC running Windows 7 Ultimate I searched and read dozens of similiar posts to try to resolve this issue with no success.
The situation is, I have a router in home with 4 PC's connected. My central PC is running Windows 7 Ultimate. The others are Windows 7 Ultimate again, and 2 running XP Pro. No special Firewalls, just have Windows Firewall enabled on all PC's, and am running KasperskyInternetSecurity2010 on all. (Have disabled these on all PC's and tried to view/connect and it didnt make a difference, same error)
Fact one: not attempting a Homegroup connection at all, just simply wishing to connect in a basic network environment where I can drag and drop files between all PC's in my Home Network or in my house , however its considered. But on the Windows 7 I am unable to view either of the XP's only the other Win7, and when I try to access that one is when I get the "Error code: 0x80070035 The network path was not found".
Furthermore, while troubleshooting the problem I opened a Command Prompt in all computers, then an "ipconfig" to view each ip address. Then began to ping each machine to determin connectivity. Which resulted in partial success. My main Win7 machine (which i am on now) was able to ping successfully to all machines. But all other machines were unable to ping to me (main Win7). with a 100% loss.
So at least I determined this is most likely a helpful fact in resolving this. Going into "services.msc" I made sure that all the obvious services are started and running:
DCHP Client, Homegroup Listener, Homegroup Provider, Link-Layer Topology Discovery Mapper, NetTcp Port SHaring Service, Network Connections, Network List Service, Network Location Awareness, TCP/IP NetBIOS Helper
All strarted and running in Automactic mode.
Not sure what other information I can give at this point, to help assist in fixing this problem. Please dont hesitate to ask for me for more info if needed. Ready and willing to try anything to get this working, except for reinstalling the OS. All my programs work great and do not wish to go through the drama ao reinstalling all my programs and activating them and redoing all my Adobe settings and CAD settings.
Someone please help !Hi,
In addition, I would like to suggest the following:
Enable NetBIOS over TCP/IP:
1. Go to “Control Panel\Network and Internet\Network Connections”.
2. Right-Click on the connection and choose Properties.
3. Click “Internet Protocol (TCP/IP) Version 4” in the list.
4. Click Properties, and then click Advanced.
5. On the Advanced TCP/IP settings windows, go to “WINS” tab.
6. Under NetBIOS setting, click “Enable NetBIOS over TCP/IP”, and then click OK.
Thanks.
Nicholas Li - MSFT -
When I open up a PDF Document all i get is an error message saying: "There was an error opening this document. The network path was not found" I dont know how to fix this, so looking for some advice please, as I really need o open up my documents.
Thank for any help.The documents I’m trying to read are already saved on my computer, under various different headings, I know that we have a server, so I only assume these documents are saved on here, as I said before I’m not good with all this techno stuff. I do my work each week ( on a payroll system) and save the documents for each company, they automatically go to the correct place. I never request for them to be saved in a certain place ( well not that I’m aware of) . I then on occasions need to open up this information, it is then that I can’t read or open the documents. We do have a tech help, but they are off sick until the 5th Jan, hence me trying to work out if I can fix this problem through this help site. Its ADOBE Reader that I’m trying to use.
-
Error:The network path was not found after shifting the development to a new machine
I hope I will find the solution here.
I'm developing my own content management system and I used the concept of URL Routing in ASP.NET and everything works just fine until I shifted developing my website from a desktop to a laptop. The problem happens only with the pages related to URL
Routing. Can anyone kindly guide me to solve this problem?
This is the full error stack:
Server Error in '/' Application.
The network path was not found
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.ComponentModel.Win32Exception: The network path was not found
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[Win32Exception (0x80004005): The network path was not found]
[SqlException (0x80131904): A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)]
System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction) +5294791
System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose) +558
System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, Boolean withFailover) +5307271
System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean ignoreSniOpenTimeout, TimeoutTimer timeout, Boolean withFailover) +145
System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString connectionOptions, SqlCredential credential, TimeoutTimer timeout) +889
System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(TimeoutTimer timeout, SqlConnectionString connectionOptions, SqlCredential credential, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance) +307
System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, SqlCredential credential, Object providerInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString userConnectionOptions) +434
System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, DbConnectionPoolKey poolKey, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection, DbConnectionOptions userOptions) +225
System.Data.ProviderBase.DbConnectionFactory.CreatePooledConnection(DbConnectionPool pool, DbConnectionOptions options, DbConnectionPoolKey poolKey, DbConnectionOptions userOptions) +37
System.Data.ProviderBase.DbConnectionPool.CreateObject(DbConnectionOptions userOptions) +558
System.Data.ProviderBase.DbConnectionPool.UserCreateRequest(DbConnectionOptions userOptions) +67
System.Data.ProviderBase.DbConnectionPool.TryGetConnection(DbConnection owningObject, UInt32 waitForMultipleObjectsTimeout, Boolean allowCreate, Boolean onlyOneCheckConnection, DbConnectionOptions userOptions, DbConnectionInternal& connection) +1052
System.Data.ProviderBase.DbConnectionPool.TryGetConnection(DbConnection owningObject, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal& connection) +78
System.Data.ProviderBase.DbConnectionFactory.TryGetConnection(DbConnection owningConnection, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal& connection) +167
System.Data.ProviderBase.DbConnectionClosed.TryOpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions) +143
System.Data.SqlClient.SqlConnection.TryOpen(TaskCompletionSource`1 retry) +83
System.Data.SqlClient.SqlConnection.Open() +96
System.Data.Common.DbDataAdapter.FillInternal(DataSet dataset, DataTable[] datatables, Int32 startRecord, Int32 maxRecords, String srcTable, IDbCommand command, CommandBehavior behavior) +121
System.Data.Common.DbDataAdapter.Fill(DataSet dataSet, Int32 startRecord, Int32 maxRecords, String srcTable, IDbCommand command, CommandBehavior behavior) +316
System.Data.Common.DbDataAdapter.Fill(DataSet dataSet, String srcTable) +86
System.Web.UI.WebControls.SqlDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments) +3387
System.Web.UI.WebControls.BaseDataList.GetData() +91
System.Web.UI.WebControls.DataList.CreateControlHierarchy(Boolean useDataSource) +488
System.Web.UI.WebControls.BaseDataList.OnDataBinding(EventArgs e) +97
System.Web.UI.WebControls.BaseDataList.DataBind() +131
System.Web.UI.WebControls.BaseDataList.EnsureDataBound() +97
System.Web.UI.WebControls.BaseDataList.CreateChildControls() +123
System.Web.UI.Control.EnsureChildControls() +171
System.Web.UI.Control.PreRenderRecursiveInternal() +138
System.Web.UI.Control.PreRenderRecursiveInternal() +337
System.Web.UI.Control.PreRenderRecursiveInternal() +337
System.Web.UI.Control.PreRenderRecursiveInternal() +337
System.Web.UI.Control.PreRenderRecursiveInternal() +337
System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +5049From logs found below issue, it seems remote connections are not allowed:
[SqlException (0x80131904): A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured
to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)]
Check the below links to trouble shoot this
http://blog.sqlauthority.com/2009/05/21/sql-server-fix-error-provider-named-pipes-provider-error-40-could-not-open-a-connection-to-sql-server-microsoft-sql-server-error/
http://forums.asp.net/t/1454592.aspx
Please click the Mark as answer button and vote as helpful if this reply solves your problem -
MDT user credentials error: Invalid credentials: The network path was not found
I have DELL E5400 and DELL Optiplex 760 pc. In the before, DELL630 is working with my MDT service, but now, DELL E5400 and DELL Optiplex 760 not working with my MDT.
When PE loaded and go to User Credentials interface, I input the user name and password(I confirm the user name and password is correct), it will display error message "Invalid credentials: The network path was not found". I checked that the network driver is correct.
After search some information in the website, someone said that maybe the network initializing timeout issue, so I according to Tim Quan guide to add following to startnet.cmd
wpeutil InitializeNetwork
ping localhost
wpeinit
Then I update the deploy location in MDT and then re-loaded it again, but unlucky, I still meet the same issue. I tried to use ipconfig /all command to check the network status, I couldn't find out local network connection. I click "Cancel" to check the error message, it will display"A connection to the deployment share could not be made. The deployment will not proceed. DHCP lease was not obtained for any networking device!Possible cause: check physical connection".
It seems that PE not loaded network driver successfully, but it is very strange that the network driver is correct.
Have someone can help me?
Thanks a lotHi,
Are you deploying Windows Vista 32bit or 64bit? Please obtain he latest network card drivers from the following sites:
Dell Latitude E5400:
http://support.dell.com/support/downloads/driverslist.aspx?c=us&cs=19&l=en&s=dhs&ServiceTag=&SystemID=LAT_E5400&os=WLH&osl=en&catid=&impid=
Dell OptiPlex 760:
http://support.dell.com/support/downloads/driverslist.aspx?c=us&cs=19&l=en&s=dhs&ServiceTag=&SystemID=PLX_760&os=WLH&osl=en&catid=&impid=
Please make sure you add the correct network driver to deployment point.
Additional Information:
http://www.techtalkz.com/windows-deployment/501217-deployment-share-connection-issue-since-mdt-2008-waik-1-1-a.html
http://www.deploymentforum.com/Community/Forums/tabid/124/forumid/16/postid/737/view/topic/Default.aspx
Hope it helps.
Tim Quan - MSFT -
Almost every day when I open my computer I get this message:
An error occurred while reconnecting P: to \ \ JSERVER\data Microsoft Windows Network: The network path was not found. This connection has not been restored.
We then have to go through the process of resetting everything from start to finish just so I can connect to the server. There is no reason that we can find that causes this other than maybe windows updating every night. Any suggestions as to how to
fix this?it sounds like you have a network drive you are trying to map even though you are not logged in maybe in a script or task instead of backing up to :P backup to the share, make sure you have security set properly to run the task when not logged on.
I assume you are running a backup of some sort as this is the backup forum.. -
Configure WDS error - The Network path was not found
I'm trying to configure WDS on Server 2012 R2. The Server is a DC and hosting DHCP and DNS. When running through the wizard or via command line to configure WDS, I get a message saying "The network path was not found". The folder gets created,
however there is no content in the folder.
We are also getting the following event "An error occurred while trying to initialize provider from WDSMDMGR from C:\windows\system32\wdsmc.dll
Any ideas?
thanks.Hi,
Since WDS is running on the same server with DHCP, did you set WDS not to listen to port 67 and configure DHCP option 60 PXEClient?
These settings can be done via WDS installation wizard.
Hope this helps. -
Cannot join domain "the network path was not found"
Hi there.
As I wanted to install new Microsoft Lync Server, I tried to prepare a virtual machine for this. For some reason I used a virtual machine that I tested for some another services, therefore it had some changes on it.
As you know before installing Lync Server your client must be join a domain and when I tried to joined it I faced with this error "The following error occurred attempting
to join the domain “ysatech”; the network path was not found "
Before my search, I thought it was DNS problem. I checked DNS but nothing was wrong.
I searched for it and I read some forums answers and I resolved it:
As I said my client server had some changes, the problem was in the NIC but not about DNS or WINS. The "Client for Microsoft Networks" of
NIC of my domain network was not checked and it must be checked.Check the dns setting on client and ensure the setting as below.
1. Each workstation/member server should point to local DNS server as primary DNS and other remote DNS servers as secondary.
2. Do not set public DNS server in TCP/IP setting of client/member server.
3. If multiple NIC are configured disable the unrequired NIC.Check the NIC binding order too.
This issue may occur if the TCP/IP NetBIOS Helper Service is not running on the client computer.
http://www.chicagotech.net/pathnotfound.htm
Network Path Not Found" Error Message When You Try to Add Workstation to Domain:http://support.microsoft.com/kb/285182
I will also recommend to enable the Client for Microsoft Networks.If still issue persist post the ipconfig /all details of client computer.
Best Regards,
Sandesh Dubey.
MCSE|MCSA:Messaging|MCTS|MCITP:Enterprise Adminitrator |
My Blog
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
Maybe you are looking for
-
How do I remove an icon or file named EDC7C000 on my screen?
Have encountered an icon or file named EDC7C000 which showed up on my screen & unable to delete it. Can anyone advise me how to remove it? TY
-
iMovie wii no longer share with iDVD. I just upgraded to Yosemite 10.10.2 and now I can't get iDVD to work properly. Any thoughts? This is what comes up.....
-
after i export a pdf file (written in Hebrew) to a Word document, the Word document is written in a Mirror-writing, how can i fix it?
-
This entry already exists in the following tables 'G/L Accounts' (OACT)
I have looked all over the forum and can not seem to find this exact error, so I hope someone can help. Current we are on SAP B1 2007 A SP 07 PL06 HOTFIX1 We get this error anytime we try to add a new G/L Account at any level. I have tried to Restore
-
I am getting a message that my start up disk is full. How can I clean it up? I'm sure I have things that I am not using and can delete.