Screen Sharing between Snow Leopard and Leopard not working

I have Leopard on my old G5 Tower and just put Snow on my Intel Mini now Screen Sharing no longer works, file sharing works my network drives chatter back and forth with no problems I just can't get a Screen Share connection. On the G5 I put in the mini's location the "communicating" barber pole churns away for about 2mins then comes back with "Connection failed. Please make sure that Screen Sharing is enabled on the computer..... Also make sure your network connection is working properly. On the Mini Screen Sharing either crashes on launch or when it does launch does the same thing as the G5. Screen Sharing is on on both machines. I was using it just mins. before installing Snow on the Mini. I did install the remote desktop update from Apple on the Mini, it seems to be for Snow only as the update isn't mentioned on Software Update on the Leopard G5. So I'm thinking of going back to Leopard on the Mini, can I do it by just doing a "restore" from Time Machine or should I dig out the old install disk?
Am I the only one out there with this problem?
Netgear router on wired Gigabit Ethernet Network, several Firewire drives, and Network Storage drives.

The G5 is running 10.5.8 with all the updates. Screen sharing on the Mini 9 times out of 10 crashes on launch when it does load the computer list shows but none on it can be selected and connected to as before. When I put the G5's name in and try to connect I get the same cannot connect make sure sharing is on message I get on the G5 trying to connect to the Mini. I have tried making new network settings and rebooting that didn't work. File sharing works works fine all network drives show up. This and Front Row being now slow jerky and audio being out of sync (I've seen this complaint else where on this forum) are the only problems I've found. But these two are just enough to send me back to Leopard on the Mini. It is my media server. I don't use iChat but I did check to see if Screen Sharing is on after it finally opened, crashed over and over, I see that it was enabled there as well. My network is wired not airport, I only use wifi for my iPod Touch.

Similar Messages

  • Screen Sharing between Mountain Lion and Tiger not working

    rMBP running 10.8.2 ML and a G3 iMac running 10.4.11 Tiger.
    When I try and use Screen Sharing on the MBP to connect to the G3 it prompts for both a username and password. I enter a valid user and pw but it fails with
    Authenication failed to "Ruby".
    Please verify you have entered the correct name and password.
    Third-party VNC clients, e.g. JollysFastVNC on my MBP and Remoter on my iPhone, can connect fine, but they only request a password.
    Any ideas?

    I've been using Screen Share on my home network for a very long time.  My most used computer, MacBook Pro (2011) was just upgraded to ML, my desktop still has Lion on it - and can't be upgraded because it is an early MacPro.  I was having intermittant problems getting the MBPro to connect to the MPro screen, and resetting the PRAM was correcting it (but it could have been the rebooting process alone - I don't know).  Now I can share the MPro disks on my network but not the screen.  Now, to me, that's wierd.  I've tried doing all kinds of setting checks, preference removal, etc.  No luck.  I can, however (as someone above mentioned) connect from my MPro (Lion) to my MBPro (ML) screen.  I've checked my Intego VirusBarrier X6 settings, i.e. blocked addresses (in the past that has happened and blocked) and I've even entered my MBPro address into the approved address section.  I've checked/rechecked the Sharing Preferences, turned them on/off, etc.  All to no avail.
    Is this a Mountain Lion / Lion issue, a Mountain Lion issue, or something somewhere corrupt?  I used to have Remote Desktop on the MPro, but for my needs Screen Share & Disk Share suit my needs on my home network.  I have LogMeInIgnition, which when the last time I tried to connect to the MBPro it showed it offline - and it isn't.  I feel there's something in ML blocking things.
    I'm open to suggestions, and a fix if needed.  This is frustrating.  Not that I can't use the exercise to walk to the room where the MPro is - not the point. 
    Tom

  • IPad screen has gone blue/green and will not work

    My iPad 1 screen has gone to black when it is turned on and willl not work. Screen stays blue/green for about 30 seconds and then turns off. Unit is charged fully and has been updated to current operating software. Gerry

    Have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider if it appears), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
    If that doesn't work then you could see if you can get it into recovery mode and restore it to your last backup : http://support.apple.com/kb/ht1808
    But you might need to contact Apple.

  • Snow Leopard and Appleworks not working well together ...

    Still a dedicated fan of Appleworks mostly because I use the vector drawing program for my design business. But, even though it works in OSX.6, it is much changed. The drag-drop images from web sites print out in dot-matrix quality. Every clicked on object becomes a "grouped picture". Therefore the object has to be ungrouped and then regrouped. The resize and rotate tools don't work. If there were other great drawing programs out there I would consider them, but I am considering going back to OSX.5. Also finding that some web sites don't like OSX.6 with Safari and my HP printers have terrible quality now and HP will not support Snow Leopard and older printers. Any other Appleworks users having problems? Thanks.

    Welcome to Apple Discussions
    Whenever you do an update, it's a good idea to do two maintenance tasks, one for the system (Repair Permissions) and one for AppleWorks (delete preferences). (Thanks to Barry for this way to format this very common answer.)
    To Repair permissions, launch Disk Utility, found in the Utilities folder in your Applications folder, click on First Aid, then on Repair Permissions.
    To delete AppleWorks’ preference files, go to HD > Users > (your account) > Library > Preferences. Find and delete the file com.apple.appleworks.plist. Find and open the folder AppleWorks in this Preferences folder, then delete all of the enclosed files (with the exception of the Button Bar Preferences if you have customized the Button Bars). AppleWorks will recreate the preference files as it needs them. You should also do this every time AppleWorks crashes as each crash will cause some corruption of the preferences. This may fix the resize & rotate issues.
    AppleWorks changes the resolution of all graphic formats except PICT to 72 dpi. There are a couple of things you can do improve the print quality of images.
    1. Turn on Fractional Character widths in Preferences > General > Topic: Text. This is a text setting, but it does improve the print quality of images.
    2. Open the image in Preview or GraphicConverter & Save As... a PICT to use in AppleWorks.
    PICT is generally the best format to use for inserting or pasting into AppleWorks. I find the resulting graphic can be resized somewhat & the resulting saved AW file is much smaller than if using JPEG or TIFF.

  • UFT 11.53 - toggle between keyword view and editor not working

    Hello,
      I have installed the enterprise version of UFT 11.53.  I have patched it with Patch # 3 (00082) and Patch # 4 (00106) in order to get Chome v 37 support.  Now when I try to toggle between keyword View and editor, it is not working.  The editor is fine.  The Keyword just set frozen and will not allow me to do anything other than, change it back to the editor
    see when I click the toggle button...its frozen...see the toggle button is down.
    It's so annoying.  I'm going to have to uninstall it again.
    Please help, if you know what's going on

    Hello sfarren,
    The forum you want is the HP Enterprise Business Community.
    Right now you are in the consumer products forum.
    I am guessing this link is the area you will want to ask your question at.
    http://h30499.www3.hp.com/t5/Unified-Functional-Testing/bd-p/sws-Fun_TEST_SF
    Good luck and hope it helps.
    PS: You might have to register again to post on that forum.

  • My iPod screen popped out alittle bit and its not working. How do i get it to work?

    The screen popped out...now it doesnt work. What do I do? Please, i need answers. I'm so lonely without my iPod =(

    This may help:
    iPod Touch Repair – iFixit
    You can make an appointment at the Genius Bar of an Apple store. However, what you describe appears to be from abuse like dropping it which is not covered by the warranty.

  • Home Sharing between Macbook Pro and AppleTV not connecting, what's wrong?

    So I have one of the late 2011 Macbook Pro models and the newest AppleTV that I do a lot of Home Sharing for movies and stuff like that. This problem keeps popping up though where they can't communicate with each other and the videos either stop loading half way through, or my AppleTV can't even connect with my macbook to start watching at all. I've gone through most of the possible solutions I've seen posted before and even the troubleshooting by apple about it. I've made sure they are both on the same apple ID, the same wi-fi network, restarted my router, even re-setup my router from scratch, closed itunes on my macbook, turned my wifi on and off a couple of times (worked for a few then stopped again), made sure that everything is on the most current software, but nothing seems to be doing the trick. This has been going on for months now and I'm pretty much sick of it happening. Somebody please help me fix this so I can get on with my movies!!

    Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
    You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
    Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
    There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment.
    If this doesn't help, contact your ISP, this is most likely a network problem.

  • Sharing Itunes library between windows desktop and macbook not working

    Hi, I just bought my laptop today. I've had it about 3 hours. I have 2147 songs on my windows itunes library, and i would love to be able to put them on the laptop too. Now, both of my computers are on the local area connection, but for some reason when i go to network places on my desktop the laptop doesnt show up. When i go to iTunes on my laptop and click import, i find my server, i find my computer, and then it asks me for a domain name, a username, and a password. I've tried multiple combinations, i'm not sure which username/pw combo its looking for but no matter what I do i get no error messages telling me i'm wrong, but absolutely nothing happens. Please help.

    This is a compleentary advice: MAKE SURE THAT WINDOWS AND MAC HAVE THE SAME GROUP NAME!
    In mac go to the preferences and activate Windows Sharing from the network.
    Then go with the finder to applications utility and Directory Access. SMB is the protocol that OS X uses to exchange with Windows. Go into its proprieties and choose the same name you have given to your windows group (USUALLY "WORKGROUP" but it may differ)
    To change the name in windows Xp is even easier. right click the m computer and choose properties and then the "Name" tag - change the group - You'll need to restart.
    Almost forgot: you have to share the Music Folder on XP to have it show up from the mac. Right click it and choose Properties - Share tab - Activate network sharing
    And remember, it is easier with a USB drive
    Message was edited by: eiapoce

  • Printer Sharing with eMac, iMac, and iBook not working

    Hello, everyone. I hope you guys can help me out with this:
    I have an Epson Stylus CX4600 hooked up to my eMac via USB. My eMac prints fine with it. The eMac is getting its internet via an Ethernet wire going downstairs into my Linksys Router, which sends my Shaw internet to my iBook, my iMac, and my eMac.
    I want to allow the iMac and iBook to access the printer over the network directly, so I can just print from those computers and have it come out the eMac printer.
    I've looked at many articles on this. So far I've installed the drivers on all computers, plus they can all network to each other over File Sharing, so they are connected.
    But I haven't been able to print yet. The most I've been able to do is get the files I try to print from the iBook and iMac to show up on the eMac, in its printer queue. Only it didn't show up for a LONG time. And when it did, the jobs automatically stopped and everytime I clicked start, it would automatically switch back to stopped again. The files would not print.
    At this point, I want to get the iBook connected to it first. If I can do that, I'll try the iMac. But the iBook is first priority. I've tried making it connect to the Printer using IPP (IP Printing), and the result was... what I explained in the above paragraph. I also tried just ordinary Printer Sharing, but it said something close to this:
    "Unable to locate eMac.local, Unknown host."
    That hardly makes sense, because at that time I also tried getting the iBook connected to the eMac over File Sharing which worked. For some reason, the "eMac.local" and "iMac.local" files don't show up in my Network thing when I connect to them, or even when they're not connected. HOWEVER, I think they did at one point. I could swear I saw "eMac.local" and "iMac.local" in the Servers folder in the Network section of the iBook at one point. But it's no longer there.
    Please help. I've described my problem as well as possible. What a long post. If there's any way to make my eMac, iMac, and iBook be able to print through my Epson Stylus CX4600 at any time directly, then I'll do it.
    Help!

    Yes. I did say that my eMac, iMac, and iBook are all
    connected to the internet and networked to each other
    over the Linksys router. I believe the router is
    still on factory settings because we never really
    "set" or programmed anything with it.
    Mac OS 9.2.2 on the iMac, Mac OS X 10.4.8 on the
    other two. IP addresses?
    192.168.1.100 is what I would use to connect to the
    eMac from the other computers.
    This is the eMac's IP, correct? Did you type it into Network, or was it assigned by the router's DHCP?
    192.168.1.101 is what I would use to connect to the
    iBook from the other computers.
    This is the iBook's IP, right? Again, fixed or DHCP?
    192.168.1.102 is what I would use to connect to the
    iMac from the other computers.
    Same for this IP.
    The iBook, as I've said, is wired. No wireless
    connections to speak of.
    Okay. Now, if the router is handing out IP addresses via DHCP, what range was it configured for? My Linksys, for example, is configured to hand out IPs in the range 192.168.0.10 to 192.168.0.254. It has the IP 192.168.0.1, so the IPs 192.168.0.2 through 192.168.0.9 are available for me to hand out as fixed IPs. If I was to hand out 192.168.0.100 as a fixed IP, the router's DHCP server would have a potential problem, as it might hand out that address too, and only one device can have a particular IP address on a particular network. If your router is handing out 192.168.1.100, .101, and .102 via DHCP, you could and probably do have a conflict if you've got those addresses set up as fixed IPs. In particular, if you have anything else on the network, including Bonjour-enabled devices such as printers, you're likely to have a conflict.
    Best way to resolve a conflict, if any:
    1 set all the Macs to either DHCP, or if fixed IPs are required, to a fixed IP outside the range of the DHCP range on the router. (Or you could just turn off DHCP on the router.)
    2 check the router to be sure that DHCP is set the way you want it, and the DHCP pool is what you think it is.
    3 shut down the Macs.
    4 turn off the router, wait 30 seconds, turn it back on.
    5 turn the Macs back on, one at a time.
    On my Linksys, the way to set the DHCP pool is simple:
    1 log into the router. (My router IP: 192.168.0.1. Yours would be 192.168.1.1.) Hit the 'Setup' tab. Verify the gateway IP. (Should be the router's IP. If it's not, something very strange is happening.) Verify the start of the DHCP pool. Verify that DHCP is on (or off, as you want). Verify the end of the DHCP pool. (My start is 192.168.0.10, and there are 245 IPs in the pool, so the end is 192.168.0.254. If I changed the number of IPs to 200, the end of the pool would be 192.168.0.209, and I'd be able to set the IPs 192.168.0.200 to 254 as fixed IPs if I wanted.) If your router allows for IPs to be reserved, you can set up reserved IPs for one or more of your Macs. (A reserved IP is an IP the router holds for a specific device. The network card in each computer has a specific MAC address; if that address is registered with the router, then every time that computer is turned on and connected it will get the IP that was reserved for it... so long as that IP is in the DHCP range and DHCP is turned on. Think of it as a fixed IP without your having to actually fix the IP.)

  • Transfer of help between F4 Help and Application not working

    I need immediate help in determining why the F4 help for BP Search not returning the selected field to the calling application.
    After the user selects the F4 BP search help screen and performs a search the value selected is not returned and displayed in the calling application.
    What is the missing link?  Also, the field not populating was one that I added through PCUI.
    Thanks.
    Jason

    your probably best off phoning motorola because obviously theres something wrong with your phone which ony they can sort out there phone number is: 0870 9010 555
    hope you get your phone sorted and hope this is a help to you

  • Facetime between my Mac and MBPr not working

    I have 1 Apple ID account.  How do I facetime my iMac from my MBPr?  When I try it, it will say "Null" at the top of the Facetime screen.  Does this problem have to do with having 1 apple ID?  I tried separating my emails so one is associated with the mac and 1 with the MBP.  Any suggestions?

    http://www.apple.com/mac/facetime/
    http://support.apple.com/kb/ht4319

  • Dynamic Link between Premire Pro and AE not working

    I've been having this issue where dynamic link is grayed out in the Premiere Pro menu, when i try to link a clip to AE. It's the same the other way round (i.e. AE to Premiere), and also the "Replace with After Effects Comp" is grayed out as well. Im using the CC version (Not CC 2014), so it should work?
    Thanks for your help!

    Hi Kevin,
    Thanks for your reply. I'm using CS6 (if that's what you mean by version - otherwise I think it's 7.0). I've never come across verifying the programs, how do I go about it?
    Thanks

  • RFC conn between SAP ERP and TREX not working

    Hi experts,
    we run a TREX instance on a Windows 2003 server and use it for our HCM portal.
    The solution is in operation since 2 years but actually we face the problem that objects which have been created within the last month will not be covered by the index.
    Without knowing about any changes in the setup I see the following error message when I perform the RFC connecten test in our ERP system:
    Logon     Connection Error
    Error Details     Error when opening an RFC connection
    Error Details     ERROR: program Trex_UKP_20071025104543 not registered
    Error Details     LOCATION: SAP-Gateway on host janos / sapgw00
    Error Details     DETAIL: TP Trex_UKP_20071025104543 not registered
    Error Details     COMPONENT: SAP-Gateway
    Error Details     COUNTER: 12906
    Error Details     MODULE: gwr3cpic.c
    Error Details     LINE: 1778
    Error Details     RETURN CODE: 679
    Error Details     SUBRC: 0
    Error Details     RELEASE: 700
    Error Details     TIME: Mon Jul 27 10:34:48 2009
    Error Details     VERSION: 2
    In the TREX admin tool on the Windows server I see the following log message:
    Source->Destination: Not set in TREX but TREX reachable -> ini file section missing?.
    After reading lots of notes I guess that I have to register the server program that's used in the RFC on the gateway.
    Unfortunately I have no idea how to do that.
    Has anybody experiences with such a problem case or can tell me how to continue?
    Is the problematic RFC realy the reason of my problem or just another side effect?
    Many thanks for your really appreciated help in advance and best regards
    Günter

    Hi again,
    the saprfc.ini on the TREX server look like follows:
    DEST=UKT
    TYPE=A
    ASHOST=medos
    SYSNR=00
    DEST=UKP
    TYPE=A
    ASHOST=janos
    SYSNR=00
    UKT is our test system which is connected to the same TREX server and everything is fine there.
    On the test system I can also see the registered server program in SMGW.
    UKP is our productive system where the configuration should be the same.
    Of course I do not see the registered server program in SMGW there.
    Is the way described in above link (RFCACCEPT) the only correct way to register my server program?
    I ask because I found information that the server program has to be developed according to this rfcaccept command and I have absolutely no idea wheather this is so.
    Thanks again for your help!
    Günter

  • Trunk between 4500-X and 4507R not working

    Hi all,
    i have got a new switch (4500-X) which i would like to connect to our existing 4507R switch. So i configured trunk ports on each of them, like i do this with all of my other access switches. I tried so many things, but i cant reach vlans from the new switch and iam totaly out of ideas
    Iam quite sure that i make a verry dump config issue, but i cant fine the fault in my config...hopyfully someone could please help me? I hope this is the right information you need.
    Many many Thanks!
    The "OLD" Switch (4507R):
    OLD#sh ver
    Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(54)SG, RELEASE SOFTWARE (fc3)
    OLD#sh run int gi3/6
    Building configuration...
    Current configuration : 149 bytes
    interface GigabitEthernet3/6
    switchport trunk encapsulation dot1q
    switchport mode trunk
    switchport nonegotiate
    end
    OLD#sh int gi3/6 switch
    Name: Gi3/6
    Switchport: Enabled
    Administrative Mode: trunk
    Operational Mode: trunk
    Administrative Trunking Encapsulation: dot1q
    Operational Trunking Encapsulation: dot1q
    Negotiation of Trunking: Off
    Access Mode VLAN: 1 (default)
    Trunking Native Mode VLAN: 1 (default)
    Administrative Native VLAN tagging: enabled
    Voice VLAN: none
    Administrative private-vlan host-association: none
    Administrative private-vlan mapping: none
    Administrative private-vlan trunk native VLAN: none
    Administrative private-vlan trunk Native VLAN tagging: enabled
    Administrative private-vlan trunk encapsulation: dot1q
    Administrative private-vlan trunk normal VLANs: none
    Administrative private-vlan trunk associations: none
    Administrative private-vlan trunk mappings: none
    Operational private-vlan: none
    Trunking VLANs Enabled: ALL
    Pruning VLANs Enabled: 2-1001
    Capture Mode Disabled
    Capture VLANs Allowed: ALL
    Unknown unicast blocked: disabled
    Unknown multicast blocked: disabled
    Appliance trust: none
    OLD#sh int gi3/6 trunk
    Port        Mode             Encapsulation  Status        Native vlan
    Gi3/6       on               802.1q         trunking      1
    Port        Vlans allowed on trunk
    Gi3/6       1-4094
    Port        Vlans allowed and active in management domain
    Gi3/6       1-3,9-10,20,23-24,26,32-40,66-68,95-101,110-111,120,200,500-501,510,995-999
    Port        Vlans in spanning tree forwarding state and not pruned
    Gi3/6       1
    The "NEW" Switch (4500-X):
    NEW#sh ver
    Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.04.00.SG RELEASE SOFTWARE (fc3)
    NEW#sh run int te1/32
    Building configuration...
    Current configuration : 94 bytes
    interface TenGigabitEthernet1/32
    switchport mode trunk
    end
    NEW#sh int te1/32 switchport
    Name: Te1/32
    Switchport: Enabled
    Administrative Mode: trunk
    Operational Mode: trunk
    Administrative Trunking Encapsulation: dot1q
    Operational Trunking Encapsulation: dot1q
    Negotiation of Trunking: On
    Access Mode VLAN: 1 (default)
    Trunking Native Mode VLAN: 1 (default)
    Administrative Native VLAN tagging: enabled
    Voice VLAN: none
    Administrative private-vlan host-association: none
    Administrative private-vlan mapping: none
    Administrative private-vlan trunk native VLAN: none
    Administrative private-vlan trunk Native VLAN tagging: enabled
    Administrative private-vlan trunk encapsulation: dot1q
    Administrative private-vlan trunk normal VLANs: none
    Administrative private-vlan trunk associations: none
    Administrative private-vlan trunk mappings: none
    Operational private-vlan: none
    Trunking VLANs Enabled: ALL
    Pruning VLANs Enabled: 2-1001
    Capture Mode Disabled
    Capture VLANs Allowed: ALL
    Unknown unicast blocked: disabled
    Unknown multicast blocked: disabled
    Appliance trust: none
    NEW#sh int te1/32 trun
    Port        Mode             Encapsulation  Status        Native vlan
    Te1/32      on               802.1q         trunking      1
    Port        Vlans allowed on trunk
    Te1/32      1-4094
    Port        Vlans allowed and active in management domain
    Te1/32      1-3,9-10,20,23-24,26,32-40,66-68,95-101,110-111,120,200,500-501,510,995-999
    Port        Vlans in spanning tree forwarding state and not pruned
    Te1/32      1-3,9-10,20,23-24,26,32-40,66-68,95-101,110-111,120,200,500-501,510,995-999

    Hi!
    Yes, sure:
    ######### OLD ##########
    OLD#sh spanning-tree vlan 3
    VLAN0003
      Spanning tree enabled protocol ieee
      Root ID    Priority    32771
                 Address     000c.30b1.7540
                 This bridge is the root
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
      Bridge ID  Priority    32771  (priority 32768 sys-id-ext 3)
                 Address     000c.30b1.7540
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
                 Aging Time  300 sec
    Interface           Role Sts Cost      Prio.Nbr Type
    Gi3/5               Desg FWD 4         128.133  P2p
    Gi3/6               Desg FWD 4         128.134  P2p
    Gi4/2               Desg FWD 4         128.194  P2p
    Gi4/3               Desg FWD 4         128.195  P2p
    Gi5/1               Desg FWD 4         128.257  P2p
    Gi5/3               Desg FWD 4         128.259  P2p
    Gi5/4               Desg FWD 4         128.260  P2p
    Gi5/5               Desg FWD 4         128.261  P2p
    Gi5/6               Desg FWD 4         128.262  P2p
    Gi6/1               Desg FWD 4         128.321  P2p
    Gi6/2               Desg FWD 4         128.322  P2p
    Gi6/3               Desg FWD 4         128.323  P2p
    Gi6/5               Desg FWD 4         128.325  P2p
    Gi6/6               Desg FWD 4         128.326  P2p
    Gi7/1               Desg FWD 4         128.385  P2p
    Gi7/2               Desg FWD 4         128.386  P2p
    Gi7/4               Desg FWD 4         128.388  P2p
    Gi7/5               Desg FWD 4         128.389  P2p
    Gi7/6               Desg FWD 4         128.390  P2p
    Po3                 Desg FWD 3         128.643  P2p
    Po6                 Desg FWD 3         128.646  P2p
    Po7                 Desg FWD 3         128.647  P2p
    OLD#sh int gi3/6
    GigabitEthernet3/6 is up, line protocol is up (connected)
      Hardware is Gigabit Ethernet Port, address is 0016.9dd4.1fe7 (bia 0016.9dd4.1fe7)
      Description: trunk core NEU
      MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      Keepalive set (10 sec)
      Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseSX
      Media-type configured as SFP connector
      input flow-control is on, output flow-control is off
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input 00:00:04, output never, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/40 (size/max)
      5 minute input rate 0 bits/sec, 0 packets/sec
      5 minute output rate 9000 bits/sec, 16 packets/sec
         809802 packets input, 156747108 bytes, 0 no buffer
         Received 809180 broadcasts (809157 multicasts)
         0 runts, 0 giants, 0 throttles
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 input packets with dribble condition detected
         77368681 packets output, 5652973144 bytes, 0 underruns
         0 output errors, 0 collisions, 3 interface resets
         0 babbles, 0 late collision, 0 deferred
         0 lost carrier, 0 no carrier
         0 output buffer failures, 0 output buffers swapped out
    ######### NEW ##########
    NEW#sh spanning-tree vlan 3
    VLAN0003
      Spanning tree enabled protocol ieee
      Root ID    Priority    32771
                 Address     000c.30b1.7540
                 Cost        4
                 Port        32 (TenGigabitEthernet1/32)
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
      Bridge ID  Priority    32771  (priority 32768 sys-id-ext 3)
                 Address     f872.ead8.4400
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
                 Aging Time  300 sec
    Interface           Role Sts Cost      Prio.Nbr Type
    Te1/32              Root FWD 4         128.32   P2p
    NEW#sh int ten 1/32
    TenGigabitEthernet1/32 is up, line protocol is up (connected)
      Hardware is Ten Gigabit Ethernet Port, address is f872.ead8.441f (bia f872.ead8.441f)
      Description: trunk sw99rz1-1-1
      MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      Keepalive set (10 sec)
      Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseSX
      input flow-control is on, output flow-control is on
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input 00:00:00, output never, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/40 (size/max)
      5 minute input rate 13000 bits/sec, 18 packets/sec
      5 minute output rate 0 bits/sec, 0 packets/sec
         365663 packets input, 26752705 bytes, 0 no buffer
         Received 365496 broadcasts (363520 multicasts)
         0 runts, 0 giants, 0 throttles
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 input packets with dribble condition detected
         3843 packets output, 745065 bytes, 0 underruns
         0 output errors, 0 collisions, 3 interface resets
         0 unknown protocol drops
         0 babbles, 0 late collision, 0 deferred
         0 lost carrier, 0 no carrier
         0 output buffer failures, 0 output buffers swapped out
    Thanks a lot!
    tobias

  • Between dowloading issues and Java not working correctly, when the next version coming out? I'm a breath away from switching to IE

    I cannot use the Java pull down menus on USAA.com, and downloads cancel when I close Firefox and cannot be resumed. What happened to the old downloader? I have to use IE in order to use USAA.com (primary banking). I tried updating Java, I tried a reinstall on firefox, clearing my cache, everything. No dice. If a new version doesn't come out soon I'm switching to IE... I've been loyal for 10 years.

    To get the old downloader back follow the directions below.
    # In the [[Location bar autocomplete|Location bar]], type '''about:config''' and press '''Enter'''. The about:config "''This might void your warranty!''" warning page may appear.
    # Click '''I'll be careful, I promise!''', to continue to the about:config page.
    # Filter '''browser.download.useToolkitIT'''.
    # Double click and '''make sure it says true.'''
    # You now have the classic downloader back! Yay!
    Any issues or confused?
    * http://kb.mozillazine.org/About:config

Maybe you are looking for

  • To attach a RTF template(Report for printing ) in the master detail form

    I have an application in which I have 3  master detail forms  of which one of the form is a gate pass form . Now this gate pass form has a report region as the detail. All that i need help is to print the Gate Pass with few fields as information in t

  • Decimal places in unit of measure in Sales order

    Hi, In the Sales Order application in PCUI, when I create a create an order for customer XYZ, and add product ABC for qty 1 which uses unit of measure PC, the qty is displayed with 3 decimals as 1,000 whereas if I use the unit of measure EA the quant

  • Camera Raw v8.7.1 Adjustment Brush Problem

    I'm using Adobe Bridge and my problem is in Adobe Camera Raw 8.7 and 8.7.1 itself. The Adjustment Brush cursor clicked position and the actual area that will be painted is not in the same area. As you can see the picture shown below, the actual paint

  • PO not found in ME9F..

    Dear All, I have created two PO's and mesages has been created in these PO's. But now in ME9F i am getting error as PO xxxxxx not found while for another PO i was able to take print out. What are the possible causes? Amit.

  • Dynamically Built Forms.

    Greetings, I've got two tables (questions and answers). With these two tables, I'm trying to construct a custom form (survey) that can have a random number of questions and answers. Questions can have multiple answers and may be either fill in the bl