SCXI 1112 and 1302 doesn't run at the same time

Hi,
I have SCXI 1112 thermocouple input module, SCXI 1180 feedthrough panel , and a SCXI 1302 terminal block connected SCXI 1000 chassis with SCXI 1349 adapter. I am trying to measure voltage by using SCXI 1180&1302, and temperature by 1112 module at the same time. When chassis is on SCXI 1112 runs without a problem; however, voltage reading coming through SCXI 1349 makes no sense (plus I can't run them at the same time, LAbview gives an error). While the chassis' power is off, it is the other way around, SCXI 1349 runs smoothly.
In addition to that, a radiometer, connected to a power supply, is wired to SCXI 1302 terminal block. When power supply is on, SCXI 1112 module's temperature reading is 4 times higher than actual value. In other words, power supply effects the readings.
Could you please give me some advice to solve this problem?
Thanks,
Azra

One piece of the puzzle you left out is the DAQ card being used in the host computer.
Without looking at some specifics on the SCXI cards/connectors you are using, I will comment you must be careful when you are using an 1180 feedthrough module. Keep in mind, the SCXI chassis is Signal Conditioning -- it's nothing without the DAQ.
I would recommend you back up a few steps, simplify the setup and test each input channel from MAX -- making sure you aren't overlapping channels between the 1180 to the DAQ and the SCXI chassis. Remember, most data from the SCXI chassis comes in on a single channel of the DAQ through the 1349.
Hope this might help.
RS

Similar Messages

Dreamweaver and Fireworks won't run at the same time

Recently, I've run into a problem where I cannot run Dreamweaver and Fireworks at the same time.
I have Dreamweaver CS4 & Fireworks CS4, which I can still run at the same time.
However when I run Dreamweaver CS5.5 and try to launch Fireworks CS5.1 I get a C++ Runtime error in FW CS5.1.
And when I run Dreamweaver CS6 and try to launch Fireworks CS6, Fireworks CS6 freezes before fully loading.
If I run DW CS6 and launch FW CS4, I can get them both to run together, but when I close FW4, DW CS6 crashes.
Any suggestions would most appreciated.
David

Historically, I've always kept prior versions installed because sometimes, albeit infrequently, I need to access extensions that aren't compatible with the newer versions of CS. Since I can run DW & Fireworks CS4 together, I'm inclined to leave them installed.
I've thought about uninstalling CS 5, but I don't think that would resolved my issue. I've already tried most of what's in the Adobe troubleshooting suggestions save for creating a new administrator account.
I think I'll hobble along with my current workarounds since I'll be migrating to a new computer very soon, which should acomplish what creating a new administrator account would. I'll probably limit the reinstall to CS 6 to eliminate any issues that might be related to having multiple versions installed, which in reality shouldn't be an issue because again, I've always done that successfully in the past.
Thanks for the suggestion just the same.

Getting 'Paint' and 'Sales History' to run at the same time

Hi,
Is this a matter of setting up a port for Paint and another for SH? Is there a limit to the number of OBI repositories that can be running at the same time?
Thanks!

Thanks.
Can two or more repositories exist in the same rpd file? Can Paint and SH be in the same rpd file and be used by seperate groups that access completely different data sources?
In our case, the dimensions and facts for glass used in a car are very different from the dimensions and facts for a car's transmission. There are similarities, true, but they are still very different.
So, in one rdp file can there be seperate presentation folders for Glass, Tires, Transmissions, Seats, Axil, Engine, Steering Wheels, Head Lights, and etc...
Each presentation folder would be used by different people. Each presentation folder would access different tables. The Glass Parts business will use the Glass presentation folder, the Axil Parts Guys will only use the Axil Presentation Folder, etc..
As always, thanks!

1.1.7 and 1.2.2 running at the same time?

I didn't find anything by searching for this specific situation. I have a program that I need to run on servers that have java 1.1.7 installed. My app fails when I try and run it on 1.1.8. I'm using features, like zip compression, that I think require 1.2, but I'm not sure. I'm also checking to see if we can upgrade the jre.
In the meantime, can I safely run two versions of java on the same box? I tested it, by running my app with jdk1.2.2 in another directory and manually setting the classpath, etc. It ran fine, just wondering if this is a bad idea?
My other option is to modify my app to work on the older jre, but I'm not sure if I can. I'm using zip and ftp. I'm guessing almost everything else could probably be modified.
Comments appreciated. Thanks.
James

You can do it fine, I have had at least 3 different versions of java running on the same box and no problems. Just make sure you have the paths right and you are ok.
teka

Macbook Pro Retina Display - Sound and video doesn't work at the same time.

I just bought a macbook pro retina display and tried to watch a movie by connecting my macbook pro via hdmi to my home theater receiver (Onkyo TX-SR309) and into my HDTV (Sony Bravia 42"). My problem is, i don't get sound from the speakers connected to the receiver.
When i disconnect the HDTV from the receiver (only the receiver is connected to the macbook pro), then sounds will comes out from the speaker.
Can somebody help me to fix this problem?

With the HDMI connected and the Onkyo powered on, open system preferences, go to the sound panel, and select the HDMI choice.
Frank

Ive downloade a movie but when watching it the sound and pic is not running at the same time, the sound is a few seconds after the pic. im running windows 8

.

Here are the individual files for those that fear the my other file of virii.
Attachments:
HASP.vi ‏88 KB
File Setup.vi ‏11 KB
Gather and Output.vi ‏149 KB

Who can shed some light on my ongoing connection problem. After upgrading my iPad Air with IOS 7.06, I could no longer connect to the internet. I have 2 MacBooks Air, 1 ipad mini and one iPhone 4S running on the same network, and they are all connected to

Who can shed some light on my ongoing connection problem.
After upgrading my iPad Air with IOS 7.06, I could no longer connect to the internet.
I have 2 MacBooks Air, 1 ipad mini and one iPhone 4S running on the same network, and they are all connected to the net and function well.
So I cleaned up the ipad completely, installed the latest firmware and reinstalled my apps : no connection.
I tried all things of resets and forgets. No result.
I have been fondling with my Airport Extreme 5 , but that did not help much.
This morning I went to a neighbor , hooked my ipad air on his network, typed the password and the thing all worked fine.
I have tried to connect the ipad air as an ethernet client, but that did not work. „Not enough power“ was the statement
Ideas anyone ?

Yes I tried this manyfold. But did not work. Reading on, I took Tesserac's advice. Shut down router and computer.
Start router after 15 minutes and wait another 10 minutes before starting the computer.
Et voila.... everything is back in working order,
Regards form Curacao, Dutch Caribean.
Pete van Linden

Can a vodcast and a photocast run at the same time ?.

Hi,
I would like have a video podcast play and a photocast run at the same time is this feasible?
Geoff

Since they're different apps and there's no way to sync something like that: no. Sounds like you could just do a video slideshow to me. That's supported by all major video creation apps.
-S

I have a mac book pro i7 2.00Ghz and 4Gb RAM. I want to run at the same time Omnisphere,Trilian and BFD 2. Will it work fine? Anybody that has some experience? Thanks

I have a mac book pro i7 2.00Ghz and 4Gb RAM. I want to run at the same time Omnisphere,Trilian and BFD 2. Will it work fine? Anybody that has some experience? Thanks

Well this is not a problem I have already bought one, my great worry is the processor and the memory..

I was backing up my iPhone and importing photos onto iPhoto at the same time , then suddenly it says no more space available (i had 48GB before i do this and now i have 18GB) i can't find the back up or the photo anywhere , how can i delete them ?

i was backing up my iPhone and importing photos onto iPhoto at the same time , then suddenly it says no more space available (i had 48GB before i do this and now i have 18GB) i can't find the back up or the photo anywhere , how can i delete them ? i dont need the pictures or the back ups , i want to delete them but they are not there

Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash first:
iPhoto ▹ Empty Trash
Do the same in other applications, such as Aperture, that have an internal Trash feature. Then reboot. That will temporarily free up some space.
According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation. You also need enough space left over to allow for growth of the data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
When Time Machine backs up a portable Mac, some of the free space will be used to make local snapshots, which are backup copies of recently deleted files. The space occupied by local snapshots is reported as available by the Finder, and should be considered as such. In the Storage display of System Information, local snapshots are shown asBackups. The snapshots are automatically deleted when they expire or when free space falls below a certain level. You ordinarily don't need to, and should not, delete local snapshots yourself. If you followed bad advice to disable local snapshots by running a shell command, you may have ended up with a lot of data in the Other category. Reboot and it should go away.
See this support article for some simple ways to free up storage space.
You can more effectively use a tool such as OmniDiskSweeper (ODS) to explore the volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one.
Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
Proceed further only if the problem isn't solved by the above steps.
ODS can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
Back up all data now.
If you have more than one user account, make sure you're logged in as an administrator. The administrator account is the one that was created automatically when you first set up the computer.
Install ODS in the Applications folder as usual. Quit it if it's running.
Triple-click anywhere in the line of text below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The application window will open, eventually showing all files in all folders, sorted by size with the largest at the top. It may take a few minutes for ODS to finish scanning.
I don't recommend that you make a habit of doing this. Don't delete anything while running ODS as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
When you're done with ODS, quit it and also quit Terminal.

Two processes running at the same time in Lookout

I have installed Lookout 5.0 with 200 I/O Points onto our server computer. The application of motion control is next to the 200 I/O points through OPC PMAC server/client. Now I would like to have a second process in the same server for trouble shooting and testing without stopping the motion control process. However, this second testing process could have also many I/O points through Serial and USB ports. I assume that the total amount of I/O points of both processes will be greater than 200.I prefer to have independent processes for control and testing because access levels. Can I have these two processes running at the same time when needed?

Hi,
From your description you are using a third party OPC server for the motion application. You could have a second Lookout process communicating with the same OPC server with no problems, as long as you do not exceed the number of I/O points your license supports.
Also, the process you are using for testing obviously could not overwrite datamembers (or registers if you will) that would interfere in the overall application, in other words you can test your application as long as you keep the coherency of the test.
So the answer would be, yes it is possible, however you are still limited to the number of I/O's your license supports... You may even consider upgrade the number of I/O's you have in your license.
Best Regards
Andre Oliveira

Multiple scripts running at the same time?

Is there a way to have multiple scripts successfully running at the same time?
At the moment if I start a second script while the first one is still running, the second one completes successfully but the first one stops. This seems to be because the first one is no longer the active document once the second one opens so can't continue.
Is there another way to script things like this so that multiple can run independently at the same time? You might ask why I'd want to run two at the same time and not just wait, but i've setup an asp.net web form front end and having problems if two people click the button around the same time.
I'm guessing this isn't going to be possible and i'm going to have to look for ways of doing this in asp.net instead and somehow queue the requests so you have to wait longer if the script is already running?
Thanks,
Andy

I'm
guessing this isn't going to be possible and i'm going to have to look
for ways of doing this in asp.net instead and somehow queue the requests
so you have to wait longer if the script is already running?
This is correct. The scripting interface to PS is single-threaded so you will need to queue up requests.

How many threads can be running at the same time

Hi!!
Dows anyone knows how many Threads can be running at the same time in the JVM.
I'm making a multi thread client-server app and I would like to know how much simultneous connections the JVM support. I'm using one Thread per connection.

Hi, thanks to all for your answers.
I think that I made the wrong question, as you said: "that means the number of threads currently created".
I'm worry about this because my application is already online (It's a mail server -SMTP and POP3 server using ORACLE for the users database- ) and some other user post in the "multi-tread forum" that almost any JVM can only have 700 threads created at the same time, and I've never heard or read anything about this.
what you mean with the stack space (memory??)
I'm using the JavaWebServer 2.0 and a servlet to start the main Thread.
Again Thanks to all for the answers but I think that the schapel answer is the one that solve my doubt...

Multiple Libraries for Video running at the same time on one PC

Hi Everyone -
I want to clarify this is for VIDEO files, not music for my 6 ATV's on the network.
Problem: I have well over 1000 VIDEOS in my iTunes Library, and I am wanting to have multiple libraries availible at the same time; not just whichever the computer has open.
We have several atv's on the network and I would like to take my video organization one step further; instead of scrolling forever in the atv menus for the video you want; I could make several libraries all availible at the same time.
Such as:
Kids Library
Workout Library
Parents Library
etc
This in turn would shrink the primary library and have less videos to sort by. I know how to create the Libraries, I just dont know how to have them all running at the same time.
Infastructure:
Windows 7 Ultimate with Drobo B800FS (16TB of storage) all connected to Cisco 3660 Gig switch with multiple atv's hardwired back.

iTunes can only open one library at a time. If you have multiple computers, or virtual machines, each could be serving a different library.
tt2

Java threads. Are they running at the same time?

Hello everybody. I am implementing a multiagent system in java and at some point in the program i need a specific function (from a specific class) to run at the same time in several "copies". Those functions are communicating with each other with some messages, so as you can understand not running at the same time is a big problem because of this messages.
Below i am giving you an example of the code i am using. I would like your opinion whether those functions are running parallel or serial. If they are not running parallel what should i do? Any opinion or something that can help me would be perfect. Thanks in advance.
//my class
public class Agent extends Thread {
                       public void MinConflicts(Agent array[],int max_moves){//code in here}
public static void main(String[] args) throws IOException {
              Agent[] fbi = new Agent[num] //num is inserted by the user
             //code here
             for(i=0;i<num;i++){
                     fbi.start(); //starting the treads
for(i=0;i<num;i++){
fbi[i].MinConflicts(fbi,max_moves); //running the function that i want to run parallel
//code here also :)

What you appear to be doing here is creating an array of Thread references (which I hope at some point gets populated with actual Thread object references!)......because your first loop is wanting to cycle through each array slot starting the referenced Thread. Then the next loop iterates through the array again, this time calling the method for each Thread object.
Assuming that you do populate the array, what this code will do is start each Thread which, I believe, will start and immediately terminate because run() has not been over-ridden. The second loop winds up calling the method for each Thread in the array. You are actually calling it from the main thread though. So, as previously advised, I think that you will run each method sequentially.
The direction that I would head with this is to override run() in your agent Thread and have that run() method call the MiniConflicts() method. Then, in your main routine you can do away with the second for loop. The looping start will start all of the individual threads and they will execute the run() method......which in essence will be executing your MiniConflicts method.
This reply is NOT a total design... I am sure that there are holes to be filled... but I think that will get you headed in the right direction.

SCXI 1112 and 1302 doesn't run at the same time

Similar Messages

Maybe you are looking for