Selective ringing of FXO lines on line share buttons
I have a customer that wants to have the UC540 emulate their existing Norstar KEY system. They have 6 lines and 15 stations. I have already setup and tested a hybrid KEY system in my lab with FXO's as shared lines https://supportforums.cisco.com/docs/DOC-15755 . This works fine. The only problem is ican not select several phones to ring and several phones not to ring when a call comes in to the FXO trunk. Either all the phones have to ring or all the phones are silent ring, not a mix of both. Is there a way around this? Perhaps in CLI.
You can comfigure individual phones sharing a DN, with 's' button for silent ring. Note this is a CLI command, I don't know and can't answer if that can be done using CCA.
Similar Messages
-
Always Use Primary Line / Auto Line Select CM 4.1(3)sr3c
Is it correct that the "Always Use Primary Line" system parameter and the phone device page "Auto Line Select" setting work together to affect a phone's off-hook behavior for incoming calls? I changed the Always Use Primary Line from the default (False to True) to change the behavior and force primary line only when the phone goes off-hook. When I then enabled Auto Line Select on the 7960G, I expected to reverse this global setting for that device only. But, that did not happen. In fact, no matter how Always Use Primary Line is set (True or False), the device page setting Auto Line Select (enable or disable) does not appear to cause any change at all. Has anyone else encountered this? If changing the Service Parameter takes effect without restarting callmanagers, wouldn't resetting the phone device force the change on the device page to take effect? Or, do I not understand the relationship between these two settings?
Auto Line Select comes into play when you are already on the phone and you have a new incoming call on another line, then should the focus change to that new ringing line so it can show you the caller-id or should the focus be on the active line. Depending on this, the softkeys and everything change on your screen and you don't have to press the line button to see all the keys.
Always use Prime Line is primary used when the phone goes off-hook. This determines if you want to go off-hook on the primary line all the time or not. If you choose to always use primary line, then everytime you go
off-hook, we use the first line on the phone and it does not matter if there is a call ringing on another line.
If its set to false, then when you go off-hook, it will go off hook on a line which is ringing and not your primary line. -
How can you change your line access selection? I have found where you can change your plan selection, but can you change the line access fee or is that a set amount?
DIVAB71,
Great question. The line access fees for the account are a set amount and can not be changed unless you are going from a basic to a smartphone or vice versa. If you are wondering about adding the month to month discount if you are out of contract Ann154 has provided great information on how to access and add the feature.
LindseyT_VZW
Follow us on Twitter @VZWSupport -
When I click on the "quick selection tool" and try to select something, it just "draws a line"
When I click on the "quick selection tool" in Photoshop CS5, and try to select something, it just "draws a line" as if the diameter were very thin and it dones't select anything.
Thanks.BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, what troubleshooting steps you have taken so far, what error message(s) you receive, if having issues opening raw files also the exact camera make and model that generated them, etc., someone may be able to help you.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
I see this problem has been posted before , but no advice has been added , please help if possible .
My iPad recently started to act up. I was using Google to find some information on birthday cakes and recipes. I selected 'images' but instead of the little thumbnails I got computer code. Lines and lines of the stuff. This only happened yesterday. The iPad was working perfectly up to then. I am having no other problems. Google images work fine on my iPhone and my Mac Book. I would be very grateful if somebody could help.The problem is absolutely not Reader. The problem is that FireFox has stepped in front of Reader and handles all the PDF stuff - wrongly in your case. FireFox is DESIGNED to take over PDF files. But it is not capable of doing IRS forms!
To start with go back to IE for these forms. When you save them to disk DO NOT DOUBLE CLICK ON THEM until this is fixed. Just open the in the normal way - start Adobe Reader and use Open from the File menu. -
Create a Macro to Index a Word Document Line by Line
Background
I have collected a bunch of keywords and references to where I can find these words in a textbook. I've put them into a Word document where each line is one Index beginning with the “Main Entry” followed by a colon and then the “Subentry”. Note
that in the "Subentry" I have included my reference in parenthesis (b1-m2).
Example Original Text:
Main Entry:Subentry (b1-m2)
Example Marked for Index:
Main Entry:Subentry (b1-m2){ XE "Main Entry:Subentry (b1-m2)" \t "" }
When it was only a page of content it was no big deal to select the entire line and <Ctrl>+<Alt>+<x> then <Enter> down the line. Now that I have about 500 lines of these word combinations, I need a more automated solution.
I have searched for KB articles that explain the various elements I need, though unsuccessfully since I don’t know what I need. I doubt I am the first person to do this, so if anyone could point me to the right documents I would greatly appreciate
it.
As a noob, how difficult of a task is this to automate with a Macro or some other method and should I even attempt it? I have a very short window of time to figure this out.
Nice to have: In the final index, I don't need the Word page numbering after the term. My references are in the parenthesis. I know how to remove it manually in Word, when I mark the index entry: Chose Options, Cross-reference
and remove the pre-populated text of "see". That adds \t "" to the index reference.
Illustrated as such:
From: Main Entry:Subentry (b1-m2){ XE "Main Entry:Subentry (b1-m2)" }
To: Main Entry:Subentry (b1-m2){ XE "Main Entry:Subentry (b1-m2)" \t "" }
My Attempt at Recording a Macro
Having zero experience writing macro’s myself, I tried recorded a simple macro using the manual keystrokes below however the text reflected in the actual index reference does not change. I also have to manually kick off the macro on every line of text.
I walked through each of the steps outlined below as I was recording a macro, however when I replay the macro, the index itself contains the exact same text for every line and does not match the original text on the new line.
I could not get the macro to repeat itself on every line. I had to keep running it until I was done (technically, when I realized it was repeating the same text within the index reference itself) but I’d like the macro to run from beginning
to end; line by line and then insert the Index itself at the end on a new page.
I realize I need some kind of loop to keep the macro going line by line.
I also need some way to mark the Main Entry within the loop (everything to the left of the colon) and then the Subentry (everything to the right of the colon to the end of the line).
Example “Index” Macro
Sub Index()
' Index Macro
Selection.EndKey Unit:=wdLine, Extend:=wdExtend
ActiveWindow.ActivePane.View.ShowAll = True
ActiveDocument.Indexes.MarkEntry Range:=Selection.Range, Entry:= _
"TV\:The Good Wife (y2014-y2015)", EntryAutoText:= _
"TV\:The Good Wife (y2014-y2015)", CrossReference:="", _
CrossReferenceAutoText:="", BookmarkName:="", Bold:=False, Italic:=False
Selection.MoveRight Unit:=wdCharacter, Count:=1
End Sub
Manually Marking Index Entries
Manually, here are the keystrokes I use to iterate my way through the document.
Manual Index Marking Keyboard Combinations:
At the beginning of the first line, press <Shift> + <End>
This selects the entire rows text
Then press <Ctrl> + <Shift> + <x>
This allows me to “Mark Index Entry”
Then press <Enter>
This confirms the Index entry
Then press <Esc>
This closes the “Mark Index Entry”
Go to the next line and repeat.
Replacing anchor
Once the creation of each index is complete, I need to be able to iterate through the document and find all anchor + colons (IE: \: ) and replace with colon (IE: :). This way, the “Main entry” and “Subentry” are handled properly when the Index is inserted.
Manual Anchor Replacement Keyboard Combinations:
At the beginning of the Word document, press <Ctrl> + <h>
Find what: \:
Replace with: :
Then <Alt> + <a>
Press the "Ok" button (or make replace silent somehow)
Then press <Esc>
This should close the "Find and Replace" screen
Inserting Index
Ideally, I would like the macro to create and insert the newly marked content into an index at the end of the document.
Manually Inserting Index Keyboard Combinations:
Press <Ctrl> + <End>
this takes us to the bottom of the document
Then press <Alt> + <s>
this chooses the "References" tab
Next press <Alt> + <x>
this chooses "Insert Index"
Next press <Alt> + <t>
This should allow you to choose a "Format" option for the index
Next press <m>
This should chose "Modern" from the "Formats" options
Finally, press <Enter>
End the macro
Example before Indexing:
TV:The Good Wife (y2014-y2015)
TV:Phineas and Ferb (y2011)
TV:Curb Your Enthusiasm (y2011-y2015)
Game:Back to the Future (y2012)
Made for TV Movie:The Magic 7(y2009)
Main Entry:Subentry (b1-m2)
Example after Indexing is completed:
The marked up text/references did not transfer over properly from the Word document I copied my question from. I had to manually type the text within the {} brackets for illustrative purposes here:
TV:The Good Wife (y2014-y2015){ XE "TV:The Good Wife (y2014-y2015)" }
TV:Phineas and Ferb (y2011){ XE "TV:Phineas and Ferb (y2011)" }
TV:Curb Your Enthusiasm (y2011-y2015){ XE "TV:Curb Your Enthusiasm (y2011-y2015)" }
Game:Back to the Future (y2012){ XE "Game:Back to the Future (y2012)" }
Made for TV Movie:The Magic 7(y2009){ XE "Made for TV Movie:The Magic 7(y2009)" }
Main Entry:Subentry (b1-m2){ XE "Main Entry:Subentry (b1-m2)" }
Example Index
G
Game
Back to the Future (y2012) · 2
M
Made for TV Movie
The Magic 7(y2009) · 2
Main Entry
Subentry (b1-m2) · 1,
2
T
TV
Curb Your Enthusiasm (y2011-y2015) · 2
Phineas and Ferb (y2011) · 2
The Good Wife (y2014-y2015) · 2
Chris SchurmanOnce I combined my Excel knowledge and Word knowledge, this became a piece of cake. Sharing my solution for anyone else who may have the need. The point of this exercise is to prepare for an open book exam and I need a quick index of my books
(there are 6 for this class). Anyway, here is how i solved (though slightly clunky, it works in seconds!)"
In Excel, I pieced the text together by concatenating the indexing markup and the contents of the pertinent cells as such:
=CONCATENATE("XE """,A2,":",B2," (b",C2,"-p",D2,")"" \t """"")
Content from Excel (with results of concantenate statement in last column:
Heading Slide Title Book Page Copy this into notepad then into word
Game Back to the Future 1 12 XE "Game:Back to the Future (b1-p12)"
Made for TV Movie The Magic 7 2 7 XE "Made for TV Movie:The Magic 7 (b2-p7)"
Main Entry Subentry 3 48 XE "Main Entry:Subentry (b3-p48)"
TV Curb Your Enthusiasm 4 100 XE "TV:Curb Your Enthusiasm (b4-p100)"
TV Phineas and Ferb 5 20 XE "TV:Phineas and Ferb (b5-p20)"
TV The Good Wife 6 35 XE "TV:The Good Wife (b6-p35)"
Then I paste special the "Values" of the last column into Word.
I run the macro below (haven't figured out how to loop yet) a few doxen times an insert the index at the bottom.
Sub Index()
' Index Macro
Selection.HomeKey Unit:=wdLine
Selection.EndKey Unit:=wdLine, Extend:=wdExtend
Selection.MoveLeft Unit:=wdCharacter, Count:=1, Extend:=wdExtend
Selection.Fields.Add Range:=Selection.Range, Type:=wdFieldEmpty, _
PreserveFormatting:=False
Selection.EndKey Unit:=wdLine
Selection.MoveRight Unit:=wdCharacter, Count:=1
End Sub
Bam; instant Index!
Chris Schurman -
Shared Lines and Line Group in 8.6.2.22900-9
We have some IP Communicator (SCCP) 8.6.14 and 7911 running SCCP11.9-2-3ES4S
We notice that sometimes when put this version of IP Communicator in a Line Group it does not ring. The desk phone will ring fine, and a IP Communicator running 7.0.3.3 will run fine.
Is this a known issue with CIPC 8.6.14 ?
Shared Lines and Line Group in 8.6.2.22900-9I neglected, this is a VMWare on UCS ... memory/HDD/CPU is all in spec.
-
Line Chart - Formatting more than 4 lines in line chart
Hi,
How to format more than 4 lines in line chart using Crystal report Designer as by default it will display 4 lines in design mode.
Able to format 4 lines but i have to display total 6 lines.
Urgent. Please help....
Thanks,
ThakurSHi,
The design mode is not the right place to edit lines, bars etc for Charts.
You can select individual lines from the Preview Mode and edit them.
Hope this helps!
-Abhilash -
Tax break up in line by line for each item in the repetitive area
Dear SAP PLD Experts
I am facing a problem for generating excise invoice in pld with tax break for each line item .
for eg : i have 5 line item in the invoice.
so , i want to show the tax break up for each line item seperately in column wise .
slNo----Item CodeQtyPriceCenvat E.Cess---- H.E.Cess-- Vat--
Total
1-- A 5 -1000 96.401.920.96 40.00--- line total
2
3
4
5
But when i am showing the Tax amount from Sales tax authorities table in repetitive area, its showing 25 line numers instead of 5 line. and tax amounts is showing line by line.
Can any body help me to sort out this issue.
Thanks
RegardsDear,
Add the UDF's on the marketing document you want the tax break up.
Apply FMS using below queries and call these UDF's on your PLD.
FOR BED
DECLARE @Amount as Numeric(19,2)
DECLARE @Rate as Numeric(19,0)
DECLARE @TAmount as Numeric(19,2)
set @TAmount =$[$38.21.Number]
SELECT @Rate=STA1.Rate
FROM OSTC INNER JOIN
STC1 ON OSTC.Code = STC1.STCCode INNER JOIN
STA1 ON STC1.STACode = STA1.StaCode Where OSTC.Code=$[$38.160.0] And STA1.SttType='9' order by STA1.EfctDate desc
set @Amount=(@TAmount * @Rate)/100
Select @Amount
For Cess
DECLARE @Amount as Numeric(19,2)
DECLARE @Rate as Numeric(19,0)
DECLARE @TAmount as Numeric(19,2)
set @TAmount = $[$38.U_BED.Number]
SELECT @Rate=STA1.Rate
FROM OSTC INNER JOIN
STC1 ON OSTC.Code = STC1.STCCode INNER JOIN
STA1 ON STC1.STACode = STA1.StaCode Where OSTC.Code=$[$38.160.0] And STA1.SttType='8' order by STA1.EfctDate desc
set @Amount=(@TAmount * @Rate)/100
Select @Amount
For HCess
DECLARE @Amount as Numeric(19,2)
DECLARE @Rate as Numeric(19,0)
DECLARE @TAmount as Numeric(19,2)
set @TAmount = $[$38.U_BED.Number]
SELECT @Rate=STA1.Rate
FROM OSTC INNER JOIN
STC1 ON OSTC.Code = STC1.STCCode INNER JOIN
STA1 ON STC1.STACode = STA1.StaCode Where OSTC.Code=$[$38.160.0] And STA1.SttType='10' order by STA1.EfctDate desc
set @Amount=(@TAmount * @Rate)/100
Select @Amount
This will help you.
regards,
Neetu -
Crystal report -How to display multiple lines in line chart?
Hi,
M struggling to display multiple lines in line chart. All the values m fetching it from database into data table in below format & data type
Category(String).....year(Int).....graph_values(Int).....table_value(String)
Test.........................2006.......... -100............................(100)
Avg..........................2006..........20................................20
Median......................2006...........5................................5
Test..........................2007...........500.............................500
Avg...........................2007............90..............................90
Median.......................2007............45..............................45
M using cross tab to display data and chart to plot line. Following fields I used in Cross tab Expert & Chart expert
Cross tab expert-
Rows u2013 category
Columns u2013 year
Summarized fields u2013 Min of table_value
In Chart Expert u2013
On Change of - Year
Show values - graph values
In cross tab m able to see the data properly but not in graph.I have three categories. Hence it should plot three lines in line chart but m able to see only one line for test category.
FYI u2013 using VS 2008 and crystal report assembly version 10.5
Urgent. Please reply soon.
Thanks
ThakurSI got the solution.
In Chart Expert - I should use
On Change of -- Year, Category
Show values -- graph values
Thanks,
ThakurS -
Is it possible to change the attributes of lines in Line Charts?
I always think there are no dumb questions but this one actually might qualify because for some reason I'm unable to find a way to change the line color and thickness in Line and Line & Bar Charts. Web Intelligence must be intelligent enough to let me do this, right?
Thnx,
DavidThank you!
So this is again another example of the Web Intelligence product not achieving it's goal, and to me that is simplifying the creation of reports that can turn data into valuable information on which people can make better, more informed decisions. Shame! And I've noticed that this is the case for far more features of Web Intelligence. Please, SAP BusinessObjects, stop including marketing only related functionalities and build a better reporting tool!
As to your answer regarding the palette, this is true but is not a generic solution as this goes for all line graphs (and bar, pie charts?). It is not very user friendly as well!
But thanks for the quick response and confirmation.
I'll keep the post open a little longer to see if anyone else has comments or similar feelings!
David -
Text file: reading char one at a time line by line
I need to read an external .txt file, one character at a time, line by line, and compare each character in order to do various things. The problem is that when I use the Buffered Reader I have only readLine() method and others to work with, but none that actually read a character at a time, and line by line. The program has to read a character, then move to the next one and read it, and so on. Then move to the next line, and read the first character, and so on. I am working with chars not Strings. Could you please help me with this problem?
InputStreamReader can read a single char.
InputStreamReader isr = new InputStreamReader(InputStream in);
isr.read(); will return 1 character from "in". -
How to create static line in line bar graph in obiee 11g?
Hello,
I have requirement where user wants to see a line in bar graph.
Now the line is just static line, we dont have data field available to draw the line in graph.
is there a way to create a static line in chart and show it in Line bar ombo graph??
Thanks in advance..e.g. i created the static line '10' in fx and now using this column as line in line bar report , but its not displaying the line at measure of '10' in chart.
Drag the column to measures section of graph (Line - Vertical Axis) to change this static value create an edit box prompt and pass the value to the column using Presentation Variable (as said by Fernando)
Thanks,
Saichand -
No control line for line item - error while posting bd to accounting
Hi all,
Billing document showing err "no control line for line item" while posting to accounting doc.Sales document is complete no in completion logs.
Previous errr: g/l missing for line item" in order incompletion after maintaining company code for customer, then refresh the g/l missing for line item is no more logs and showing the error "no control line for line item" while posting bd to accts.
Please help
Regards
anushHello Anush,
if the company data of the payer was not created when the sales order has been created, then the system could not create the correct records in table VBREVK. Once the company data has been maintained the VBREVK records could be corrected by re-saving the sales, but only if no billing document exists.
In your case you already created the billing document.
Please try these step:
1. reverse billing document
2. run VA02 add a blank char to PO number, save
3. create new billing document
Best regards,
Ivano. -
My firefox has decided to load in a line by line format, why?
My broser started loading in a line by line formay. I need to know what to do about this. This happens on most websites, but not all. Will not allow me on to the facebook site. sample below.
Access Email using the XFINITY Mobile app »
Xfinity
Home
TVNew
Connect
Help
Account
Security
Shop
Register
Sign In
Profile Set-up
Progress: 100%
View More Options
Hi chvbob
Sign Out
Welcome
Complete the XFINITY set up process so you can browse, watch and record your TV shows & movies anytime, anywhere.
Set Up Xfinity
Welcome
Just 0 more steps and you're done:
You're Done!
Complete Set-up
View Profile
Thank You
Coming back to complete the set-up is simple. Just click on the arrow to the right of the progress bar to see where you left off, then finish your set-up tasks.
Comcast.net
Search:
enhanced by Google
Today's Highlights
October 06, 2011
10 Unsolved Mysteries of Amanda Knox Case
10 Unsolved Mysteries of Amanda Knox Case
Amanda Knox is freed and back in the U.S., but questions about the Italian murder case remain.
Judge: 'This Case Will Never Be Solved'
Knox's Tearful Arrival Back in United States
Family, Friends Celebrate Knox's Return to U.S.
Woman on Knox's Flight Home Speaks Out
Reactions to the Amanda Knox Verdict
New End-of-the-World Prediction
New End-of-the-World Prediction
The world didn't end last May, but that doesn't mean we're out of the woods just yet...
Harold Camping Thinks the World Will End Soon
Evangeline Lilly Is Sick of Talking About 'Lost'
Watch the Full Episode of 'Jimmy Kimmel Live'
Full Episodes of 'Jimmy Kimmel Live'
Find TV Listings for Your Area
Real Estate: What Will $200K Buy?
Real Estate: What Will $200K Buy?
Will you get a luxury 4-bedroom home or a cramped studio? See what your dollar's worth in these cities:
Chicago
Houston
Denver
What Does $200K Buy in Other Cities?
10 Tips to Get the Best Mortgage
6 Must-Do's Before You Buy
Listing Red Flags
Should You Clean the Foreclosure Next Door?
Jobs Remembered as 'Visionary'
Apple founder Steve Jobs lost his long battle with pancreatic cancer yesterday. He was 56.
Tributes Pour In from Across the Globe
Video
Apple Fans Mourn Jobs
Jobs' Life in Pictures
Jobs Told Us What We Needed Before We Knew
Digital Titans, Gadget Junkies Mourn Steve Jobs
Evolution of Apple
Little-Known Steve Jobs Facts
Watch the Greatest TV Moments
TV Guide counts down the top 100 memorable moments in television history.
View '100 Great TV Moments' Online for Free
Watch More of '100 Great TV Moments' Online
Watch 'Fat Albert and the Cosby Kids' Online
Watch 'Hill Street Blues' Online
Watch Thousands of TV Shows for Free
5 Lightning-Fast Porsches
Do you have a need for speed? Buckle up and check out the fastest Porsches permitted to cruise the streets.
Fastest Street-Legal Porsches
5 Super Cars That Shatter 200 MPH
Beautiful Exotic Cars
Famous TV Cars
5 Cars That Stand Out from the Crowd
Most Stolen Cars
Future Collectible Cars
Ways to Save on Groceries
In just one year, the cost of groceries has increased by 4.2 percent. Learn how to stop your grocery bills from growing.
5 Tips to Fight Rising Prices
Secrets of Supermarket Prices
Make Your Groceries Last Longer
Clean Up the Cost of Laundry
The Best Savings Accounts
Did They Go Under the Knife?
From Steve Martin to Simon Cowell, these leading men are rumored to have had lifts, Botox and other procedures.
Did They or Didn't They?
Celebrity Surgery: Before & After
Stars Who Insured Their Body Parts
Watch Full Episodes of 'Nip/Tuck'
Super-Skinny Celebrities
Slow PC? Speed It Up
Improve your computer's speed and performance with a PC tune-up. This special offer is available exclusively to XFINITY customers.
Learn More
Tune Up Your PC's Speed and Performance
Keep Your Computer Safe and Secure
Get a Free Month of XFINITY Signature Support
Mexico Vacation Sale
Check out spectacular specials on flights and all-inclusive hotel stays across Mexico. Two great deals, one unforgettable vacation.
Flights $119+
All-Inclusive Hotels $69+
Disney Resort Vacations: 3 Nights with Air $480+
Jamaica from $469
Hawaii from $589
Tour the UK: 6 Nights, 3 Countries with Air $910+
Flight Deals: Atlanta $59+
San Diego $119+
Highest-Earning Women in Hollywood
Forbes has released its annual list of the best-paid women in entertainment. Did Oprah Winfrey retain her crown?
Find Out Now
Lady Gaga Wears False Teeth
Richest Star Moms
Most Powerful Celebrities
Watch Oprah Winfrey Network Clips & Episodes
Best-Paid Actresses
Wealthiest Stars Under 30
Get Paid to Eat Out
A new website offers 'insider pricing' of 30% off your bill when you use it to make a reservation.
How Does It Work?
Food News, Cooking Shows, More
America's Best Chain Restaurants
Guide to Restaurant Tipping
12 Dinner Date Deal Breakers
Amanda Knox
'Jimmy Kimmel'
$200K Homes
Steve Jobs
TV Moments
Fastest Porsches
Grocery Savings
Celeb Surgery
Tech Help
Mexico Sale
Richest Women
Get Paid to Eat
Amanda Knox
Previous
1 - 1.0336417157275022 of 12
Next PLAYPAUSE
Top Videos
Finance News
Previous
1 - 1.0336417157275022 of 16
Next
Previous
Loading...
'DWTS' Star's Revealing Pics'DWTS' Star's Revealing Pics
'Bachelor' Beauty's New Man'Bachelor' Beauty's New Man
Depp's Comment Sparks OutrageDepp's Comment Sparks Outrage
Camille Grammer Rocks BikiniCamille Grammer Rocks Bikini
'DWTS' Star's Revealing Pics'DWTS' Star's Revealing Pics
Next
Watch XFINITY TV Online
History Hits
Classic Comedy
Fox Toons
Reality Rewind
'Pawn Stars'You are addressing an audience that is not affiliated with Apple. We can't help you.
Maybe you are looking for
-
Installation troubles: silent exit? PLEASE HELP!
I am installing jdk-1_5_0_04-windows-i586-p.exe on a vital Windows 2003 Enterprise-running personal computer, and after clicking "Next" in the setup destination dialogue, the installer silently fails. I have included the following log-file which inco
-
Hiding some fields in default selection screen in hr abap
Hi Experts, I am new to hr abap.I have created default selection screen by using LDB .in that i wants to display only the personnel number field. could any help me how to hide further selections,sort order and search helps at top of screen. thanks
-
Transport user exit frm development to production server.
HI Gurus! please tell me how to transport user exit frm development to production server. Points Sure! Regard, Rahul .
-
Trying to migrate SQL Server 2000 to Oracle 10g.
Hi. I´m trying to migrate from Sql Server 2000 to Oracle 10g and I got some troubles. I have connected both databases with my Oracle Sql Server, after that I went to the Menu--> Migrate--> Fast Migration and then fill all the steps necesary. I can se
-
AIR 2.7 and molehill combi for iOS???
Hi, how do you tell Flash CS 5.5 to compile an iOS app with AIR 2.7 and Flash player 11? (Molehill) I have both installed but Flash seems to complile to player 10 in AIR 2.7 and I want player 11 in AIR 2.7. Any help much welcome! regards!