Series of problems

I am burning a 90 minute panel to dvd. I compressed it from FCP into MPEG-4. It comes out to about 700 MB. I have an 8.5GB DVD+R DL. Then when I Build/format, I get an error: a Suitable marker could not be found in the required layer break range. It shouldn't need a break if it's only 700 MB, not even close to 4GB.
Message was edited by: ps_mankikar

DVD Video uses MPEG 2 compression. DVD Studio Pro is recompressing your MPEG 4 a second time to make it work. Not good.
Use Compressors DVD Best (or Fastest) Quality 90 Minute preset with 16:9 or 4:3 as appropriate. Select all, then delete the AIFF audio.

Similar Messages

Facing a series of problems in production server

Dear All,
I am facing a series of problems.
We are using ecc5 on windows with oracle 9i.
Two nodes on cluster.
1. I am getting error in log file
TNS-01151: Missing listener name, LISTENER2, in LISTENER.ORA
2. dev_disp getting error *** WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 4 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 3893]
MtxInit: -2 0 0
3. Suddenly shutdown of server.
4.E error in nmiconf.log
I am unable to find the Listener problem because at present it listener is up.
Please help to find the root cause because there 3 Listener.ora
1     LISTENER1.log current date.
      2     LISTENER. Log with old date
And which file and what change I have to do.
2.What settings have to change in DNS settings?
3.What is suddenly caused of server shutdown?
Log file of LISTENER2.log
TNSLSNR for 64-bit Windows: Version 9.2.0.7.0 - Production on 22-SEP-2008 11:33:50
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
System parameter file is E:\oracle\ora92\network\admin\listener.ora
Log messages written to E:\oracle\ora92\network\log\listener2.log
Trace information written to E:\oracle\ora92\network\trace\listener2.trc
Trace level is currently 0
Started with pid=1332
TNS-01151: Missing listener name, LISTENER2, in LISTENER.ORA
Log file of LISTENER1.log
Started with pid=1180
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=@@@@-@@@@.@@@@.COM)(PORT=1528)))
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
TNSLSNR for 64-bit Windows: Version 9.2.0.7.0 - Production on 22-SEP-2008 11:33:50
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
System parameter file is E:\oracle\ora92\network\admin\listener.ora
Log messages written to E:\oracle\ora92\network\log\listener1.log
Trace information written to E:\oracle\ora92\network\trace\listener1.trc
Trace level is currently 0
Started with pid=1304
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=@@@@-@@@@.@@@@.COM)(PORT=1528)))
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
Log file of LISTENER. log
TNSLSNR for 64-bit Windows: Version 9.2.0.7.0 - Production on 11-AUG-2008 17:10:07
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
System parameter file is E:\oracle\ora92\network\admin\listener.ora
Log messages written to E:\oracle\ora92\network\log\listener.log
Trace information written to E:\oracle\ora92\network\trace\listener.trc
Trace level is currently 0
Started with pid=7440
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=@@@@-@@@@.@@@@.COM)(PORT=1527)))
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
11AUG-2008 17:10:08 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=#####1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
11-AUG-2008 17:59:26 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=prd1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
11AUG-2008 18:14:17 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=prd1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
11-AUG-2008 18:17:35 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=prd1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
LISTENER.ORA
LISTENER.ORA Network Configuration File: E:\oracle\ora92\network\admin\listener.ora
Generated by Oracle configuration tools.
STARTUP_WAIT_TIME_FSL@@@@-SAP-ORAV = 0
LISTENER1 =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS_LIST =
        (ADDRESS = (PROTOCOL = TCP)(HOST = @@@@-@@@@)(PORT = 1528))
ADMIN_RESTRICTIONS_FSL@@@@-SAP-ORAV = on
FSL@@@@-SAP-ORAV =
(ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = PRD1))
    (ADDRESS = (PROTOCOL = IPC)(KEY = PRD1.WORLD))
    (ADDRESS = (COMMUNITY = SAP.WORLD)(PROTOCOL = TCP)(Host = #####)(Port = 1527))
This file is written by Oracle Services For MSCS
on Tue May 16 21:20:04 2005
TRACE_LEVEL_FSL@@@@-SAP-ORAV = OFF
CONNECT_TIMEOUT_LISTENER = 10
STARTUP_WAIT_TIME_LISTENER = 0
ADMIN_RESTRICTIONS_LISTENER = on
LISTENER =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS_LIST =
        (ADDRESS = (PROTOCOL = TCP)(HOST = @@@@-@@@@)(PORT = 1527))
SID_LIST_FSL@@@@-SAP-ORAV =
(SID_LIST =
    (SID_DESC =
      (SDU = 32768)
      (SID_NAME = PRD1)
      (ORACLE_HOME = E:\oracle\ora92)
LISTENER_000.ORA
This file is written by Oracle Services For MSCS
on Tue May 16 21:20:02 2005
LISTENER =
(ADDRESS_LIST=
    (ADDRESS=
      (PROTOCOL=IPC)
      (KEY=PRD1.WORLD)
    (ADDRESS=
      (PROTOCOL=IPC)
      (KEY=PRD1)
    (ADDRESS=
      (COMMUNITY=SAP.WORLD)
      (PROTOCOL=TCP)
      (HOST=########)
      (PORT=1527)
SID_LIST_LISTENER =
(SID_LIST =
    (SID_DESC =
      (SDU = 32768)
      (SID_NAME = PRD1)
      (ORACLE_HOME = E:\oracle\ora92)
STARTUP_WAIT_TIME_LISTENER = 0
CONNECT_TIMEOUT_LISTENER = 10
TRACE_LEVEL_LISTENER = OFF
ADMIN_RESTRICTIONS_LISTENER = on
LISTENER_001.ORA
Filename......: listener.ora
Created.......: created by SAP AG, R/3 Rel. >= 6.10
Name..........:
Date..........:
@(#) $Id: //bc/640-2/src/ins/SAPINST/impl/tpls/ora/ind/LISTENER.ORA#4 $
ADMIN_RESTRICTIONS_LISTENER = on
LISTENER =
(ADDRESS_LIST =
        (ADDRESS =
          (PROTOCOL = IPC)
          (KEY = PRD1.WORLD)
        (ADDRESS=
          (PROTOCOL = IPC)
          (KEY = PRD1)
        (ADDRESS =
          (COMMUNITY = SAP.WORLD)
          (PROTOCOL = TCP)
          (HOST = @@@@-@@@@)
          (PORT = 1527)
STARTUP_WAIT_TIME_LISTENER = 0
CONNECT_TIMEOUT_LISTENER = 10
TRACE_LEVEL_LISTENER = OFF
SID_LIST_LISTENER =
(SID_LIST =
    (SID_DESC =
      (SDU = 32768)
      (SID_NAME = PRD1)
      (ORACLE_HOME = E:\oracle\ora92)
nmiconf.log
DBSNMP for 32-bit Windows: release 9.2.0.7.0 - Production on 22-SEP-08 11:33:50
Discovering services on @@@@-@@@@ configured on host addresses {@@@@-@@@@.@@@@.COM 192.168.10.5 @@@@-@@@@}
Warning : Skipping OracleOraHome92TNSListenerFsl@@@@-sap-orav : Could not find corresponding listener definition in
Warning : Skipping OracleOraHome92TNSListenerLISTENER2 : Could not find corresponding listener definition in
Warning : Skipping OracleOraHome92TNSListenerprd1 : Could not find corresponding listener definition in
Warning : Skipping OracleOraHome92TNSListenerprd1.world : Could not find corresponding listener definition in
Warning : LISTENER1 defined in E:\oracle\ora92\network\admin\listener.ora will be skipped, because it does not monitor any of the valid SIDs
Warning : LISTENER defined in E:\oracle\ora92\network\admin\listener.ora will be skipped, because it does not monitor any of the valid SIDs
Warning : No Listener found for SID PRD1. PRD1 will be skipped
Could not determine location of emtab.
Regards,
Shiva

Dear All,
I am facing a series of problems.
We are using ecc5 on windows with oracle 9i.
Two nodes on cluster.
1. I am getting error in log file
TNS-01151: Missing listener name, LISTENER2, in LISTENER.ORA
2. dev_disp getting error *** WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 4 seconds
***LOG GZZ=> 1 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 3893]
MtxInit: -2 0 0
3. Suddenly shutdown of server.
4.E error in nmiconf.log
I am unable to find the Listener problem because at present it listener is up.
Please help to find the root cause because there 3 Listener.ora
1     LISTENER1.log current date.
      2     LISTENER. Log with old date
And which file and what change I have to do.
2.What settings have to change in DNS settings?
3.What is suddenly caused of server shutdown?
Log file of LISTENER2.log
TNSLSNR for 64-bit Windows: Version 9.2.0.7.0 - Production on 22-SEP-2008 11:33:50
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
System parameter file is E:\oracle\ora92\network\admin\listener.ora
Log messages written to E:\oracle\ora92\network\log\listener2.log
Trace information written to E:\oracle\ora92\network\trace\listener2.trc
Trace level is currently 0
Started with pid=1332
TNS-01151: Missing listener name, LISTENER2, in LISTENER.ORA
Log file of LISTENER1.log
Started with pid=1180
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=@@@@-@@@@.@@@@.COM)(PORT=1528)))
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
TNSLSNR for 64-bit Windows: Version 9.2.0.7.0 - Production on 22-SEP-2008 11:33:50
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
System parameter file is E:\oracle\ora92\network\admin\listener.ora
Log messages written to E:\oracle\ora92\network\log\listener1.log
Trace information written to E:\oracle\ora92\network\trace\listener1.trc
Trace level is currently 0
Started with pid=1304
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=@@@@-@@@@.@@@@.COM)(PORT=1528)))
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
Log file of LISTENER. log
TNSLSNR for 64-bit Windows: Version 9.2.0.7.0 - Production on 11-AUG-2008 17:10:07
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
System parameter file is E:\oracle\ora92\network\admin\listener.ora
Log messages written to E:\oracle\ora92\network\log\listener.log
Trace information written to E:\oracle\ora92\network\trace\listener.trc
Trace level is currently 0
Started with pid=7440
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=@@@@-@@@@.@@@@.COM)(PORT=1527)))
TIMESTAMP * CONNECT DATA [* PROTOCOL INFO] * EVENT [* SID] * RETURN CODE
11AUG-2008 17:10:08 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=#####1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
11-AUG-2008 17:59:26 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=prd1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
11AUG-2008 18:14:17 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=prd1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
11-AUG-2008 18:17:35 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=)(USER=prd1adm))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=153093888)) * status * 0
LISTENER.ORA
LISTENER.ORA Network Configuration File: E:\oracle\ora92\network\admin\listener.ora
Generated by Oracle configuration tools.
STARTUP_WAIT_TIME_FSL@@@@-SAP-ORAV = 0
LISTENER1 =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS_LIST =
        (ADDRESS = (PROTOCOL = TCP)(HOST = @@@@-@@@@)(PORT = 1528))
ADMIN_RESTRICTIONS_FSL@@@@-SAP-ORAV = on
FSL@@@@-SAP-ORAV =
(ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = PRD1))
    (ADDRESS = (PROTOCOL = IPC)(KEY = PRD1.WORLD))
    (ADDRESS = (COMMUNITY = SAP.WORLD)(PROTOCOL = TCP)(Host = #####)(Port = 1527))
This file is written by Oracle Services For MSCS
on Tue May 16 21:20:04 2005
TRACE_LEVEL_FSL@@@@-SAP-ORAV = OFF
CONNECT_TIMEOUT_LISTENER = 10
STARTUP_WAIT_TIME_LISTENER = 0
ADMIN_RESTRICTIONS_LISTENER = on
LISTENER =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS_LIST =
        (ADDRESS = (PROTOCOL = TCP)(HOST = @@@@-@@@@)(PORT = 1527))
SID_LIST_FSL@@@@-SAP-ORAV =
(SID_LIST =
    (SID_DESC =
      (SDU = 32768)
      (SID_NAME = PRD1)
      (ORACLE_HOME = E:\oracle\ora92)
LISTENER_000.ORA
This file is written by Oracle Services For MSCS
on Tue May 16 21:20:02 2005
LISTENER =
(ADDRESS_LIST=
    (ADDRESS=
      (PROTOCOL=IPC)
      (KEY=PRD1.WORLD)
    (ADDRESS=
      (PROTOCOL=IPC)
      (KEY=PRD1)
    (ADDRESS=
      (COMMUNITY=SAP.WORLD)
      (PROTOCOL=TCP)
      (HOST=########)
      (PORT=1527)
SID_LIST_LISTENER =
(SID_LIST =
    (SID_DESC =
      (SDU = 32768)
      (SID_NAME = PRD1)
      (ORACLE_HOME = E:\oracle\ora92)
STARTUP_WAIT_TIME_LISTENER = 0
CONNECT_TIMEOUT_LISTENER = 10
TRACE_LEVEL_LISTENER = OFF
ADMIN_RESTRICTIONS_LISTENER = on
LISTENER_001.ORA
Filename......: listener.ora
Created.......: created by SAP AG, R/3 Rel. >= 6.10
Name..........:
Date..........:
@(#) $Id: //bc/640-2/src/ins/SAPINST/impl/tpls/ora/ind/LISTENER.ORA#4 $
ADMIN_RESTRICTIONS_LISTENER = on
LISTENER =
(ADDRESS_LIST =
        (ADDRESS =
          (PROTOCOL = IPC)
          (KEY = PRD1.WORLD)
        (ADDRESS=
          (PROTOCOL = IPC)
          (KEY = PRD1)
        (ADDRESS =
          (COMMUNITY = SAP.WORLD)
          (PROTOCOL = TCP)
          (HOST = @@@@-@@@@)
          (PORT = 1527)
STARTUP_WAIT_TIME_LISTENER = 0
CONNECT_TIMEOUT_LISTENER = 10
TRACE_LEVEL_LISTENER = OFF
SID_LIST_LISTENER =
(SID_LIST =
    (SID_DESC =
      (SDU = 32768)
      (SID_NAME = PRD1)
      (ORACLE_HOME = E:\oracle\ora92)
nmiconf.log
DBSNMP for 32-bit Windows: release 9.2.0.7.0 - Production on 22-SEP-08 11:33:50
Discovering services on @@@@-@@@@ configured on host addresses {@@@@-@@@@.@@@@.COM 192.168.10.5 @@@@-@@@@}
Warning : Skipping OracleOraHome92TNSListenerFsl@@@@-sap-orav : Could not find corresponding listener definition in
Warning : Skipping OracleOraHome92TNSListenerLISTENER2 : Could not find corresponding listener definition in
Warning : Skipping OracleOraHome92TNSListenerprd1 : Could not find corresponding listener definition in
Warning : Skipping OracleOraHome92TNSListenerprd1.world : Could not find corresponding listener definition in
Warning : LISTENER1 defined in E:\oracle\ora92\network\admin\listener.ora will be skipped, because it does not monitor any of the valid SIDs
Warning : LISTENER defined in E:\oracle\ora92\network\admin\listener.ora will be skipped, because it does not monitor any of the valid SIDs
Warning : No Listener found for SID PRD1. PRD1 will be skipped
Could not determine location of emtab.
Regards,
Shiva

Mac Pro (early 2008) - a series of problems

Like many people here, I've been hit with a series of Mac Pro (early '08) issues. I've had the machine for a little over a month and I love it when it's working. But recently, the aforementioned "series of problems" has arisen - ATI graphics card freeze, reboot from sleep, etc.
But the weirdest, and perhaps most troubling issue is one with my main hard drive (Hitachi 1 TB) in Bay 1 (I have another 1 TB drive [Seagate] in Bay 2). The temperature of my Hitachi drive hovers around 101-106 degrees when active, and stays in mid-90s when relatively idle. I was wondering if this is considered a normal temp range for a hard disk? The Segate drive in Bay 2 runs around 88 degrees at its hottest (according to the iStat widget). While it's not used as much as the start-up drive, I am a bit alarmed by the difference in the temperatures of the drives...
Possibly related to this is the fact that my start-up drive (Hitachi) has some disk repair issues pop up when I ran Disk Utility. This might be due to all the hard shut downs I had to do because of the ATI graphic card freezes, but I was dismayed to see it happen so early in the computer's lifecycle.
And finally -- and I know this is a long post; I appreciate those you have stuck around -- I noticed on my Hitachi drive that I seemed to "lose" about 25 gigs of data. Not stuff that I lost because it was deleted, but rather it was as if I had transferred a huge 25-gig file onto the hard disk which took up the space.
For instance, earlier in the day, it said I had 490 gigs available, but several hours later, after transferring nothing to the hard drive, it mysteriously said I had 469 gigs available. Has anyone experienced anything like this before?
Thanks for your time...

When I purchased my Mac Pro in mid-January from the local Apple store, I also bought two Hitachi Deskstar 7K1000 1 TB drives from the Apple Store which they installed. I configured these drives as a Raid 0 array for use with Final Cut Studio 2. This Raid array of two 1 TB Hitachi drives has worked flawlessly. My OS is located on the 320 GB Seagate that came with the stock configuration of the Mac Pro under heavy A/V application use. The Hitachi 1 TB drives are known to run a little hotter than other drives, but I don't have any software that monitors the temperatures on my Hitachi drives so I cannot say if they are running as warm as you have noted. Here is a link to a review of the 7K1000 that showed an operating temperature of 31-39 degrees Centigrade in moderately heavy use:
http://www.anandtech.com/storage/showdoc.aspx?i=2969.
Based on what you have reported here is what I would do: (1) Erase and zero your Hitachi 1 TB system drive. This will take several hours but will map out any bad sectors on the drive. (2) REinstall your OS and applications. I would not restore from TM because you may have backed up the problems that were existing on your system drive.
The Hitachi 1 TB drives are thermally protected. Here is the complete data sheet on the Hitachi 1 TB drive: http://www.hitachigst.com/tech/techlib.nsf/techdocs/67A68C59B27368FC862572570080 FC70/$file/Deskstar7K1000010307final.pdf
It really does not sound to me like your drives are the problem and that they are probably operating within normal limits, but a call to Hitachi tech support would probalby clear that up firmly.
Tom

¿Cual puede ser el problema con unos calendarios importados a icloud que se sincronizan perfectamente con mi iphone pero no con mi mac?.

¿Cual puede ser el problema con unos calendarios importados a icloud que se sincronizan perfectamente con mi iphone pero no con mi mac?. Aclaro que no es un problema de la configuracion ya que si añado nuevas entradas al calendario si se sincronizan. Mas bien parece que las entradas importadas originalmente tuvieran algun problema interno que solo afecta al MAC.

La aplicaciones que compraste con la cuenta vieja solo podran ser actualizadas via la cuenta vieja. No hay manera de "fusionar" las dos cuentas.
Las aplicaciones (y canciones etc) estan atadas a la cuenta de la cual se ejecuto la compra.

Photosmart 7510 e-all-in-one series/ Printhead problem.

Our photosmart 7510 e-all-in-one series has an message that reads
Printhead appears to be missing, not detected, or incorrectly installed.
Not able to locate the problem.
Happened right after I changed the ink.

Hello harry4955,
Welcome to the HP Support Forums!
I see that the HP Photosmart 7510 is displaying an error regarding the print head is missing, stating after changing your ink cartridges.
I was able to locate this HP document: 'Missing or Failed Printhead' or 'Printhead is Missing, Not Detected, or Not Properly Installed' Mes.... I hope it helps, if not you may need to call HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here.
Regards,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Line chart with more than 15 data series - color problem

Hi all,
I've built a line chart with 32 data series (user can control, which of them are displayed at a time). For series 16 to 32 I did manipulate the URL in the browser directly, because Application Express does only display parametrs for up to 15 series. This works fine so far except of displaying the colors. For each sieries I defined a different color. 29 of my 32 series are displayed in the desired color. But series 29, 31 and 32 are displayed in a default-color (#0099CC). It seems that this is a SVG-problem. In the SVG-source I find the wrong color. When I export my application, I see the right color.
Thanks for help,
Chris

Hello,
Which version of APEX are you using?
Go to your Flash Chart attributes - get into your series (click the icon) in the section of Series Query you'll find the maximum rows.
Regards,
Dimitri
-- http://dgielis.blogspot.com/
-- http://apex-evangelists.com/
-- http://apexblogs.info/

Touchsmart 310 1110 uk. Intel (R) 6 Series chipset problems.

What are these issues?
Although the site explains it reasonable well it isn't crystal clear, in fact the graphics are terrible, if I didn't know beter i would think that they didn't want me to find out if I have a PC with chipset issues.
Is there a place to go to automatically test and diagnose for the presence of these chipset issies?
I have only recently discovered this and according to their site I have to act within 15 days, I have 2 days left. I think that's a bit naughty anyway. Surely when you register your product they should have automatically informed me that there may be a problem. I do think that a have these problem chips.

@TheFamilyTech
Here is the driver page for your notebook which includes the HP customized drivers.
Compaq Presario CQ62-219WM Notebook PC Drivers
As you mentioned that the update utility was not working for you, try uninstalling the existing driver and use the one from here and see if it works for you.
Intel 4 Series Express Chipset Family Graphics Driver
Let me know how it goes.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Fixing a TV series download problem?

I have had no problems in the past downloading. But lately, when I tried to download a tv series (24 and grey's) I get an error message -3253. Not sure what this is and the Itunes help has not been able to solve it. Downloads seem to work fine till about 110MB (about a fourth of the TV show) and then it refuses to download anymore.
Anyone else encounter this problem? What worked?

Hi, yes there is a way to you your TV series on your other mac and, if I'm not mistaken, even your laptop.
This link here should help you: http://www.apple.com/support/homesharing/

Series Downloads problem

Hi everyone,
I am having trouble downloading a TV series onto my Windows Laptop from itunes.
I have already downloaded 1 episode of the series through iTunes and it wont let me download the remainder of my purchase. It keeps saying that I have not downloaded the first episode, but I have, and then it tries to download the first episode again, with no sign of the other 23.
I have removed the download and tried to start the series download again, but no luck. Does anyone have any ideas?
Thanks, Kaz

try this:
in iTunes, access your *purchase history* via your account in the iTunes store,
find the file(s) in question, and click on the *report a problem button*. report the problem.
clicking here should take you directly to your iTunes store log-in window.
JGG

Time Series algorithm problem

Hi,
problem-In Time Series Algorithm predication is wrong if Sales value is negative
i have data for more than 3 years ,
sample data like
Year/Month
Zone-1 Sales
201001
-5467.66
201002
2345.88
201003
-7895.33
201004
2345.65
201005
120.2333
Due to negative value my prediction for next month is wrong. Please tell me how I can handle this problem. Negative values come due to sales return in zone.

Hi Leo,
Thanks a lot for replay.
but using help of this blog also this problem not solve.
is this problem can we solve using "Seasonal Decomposition of Time Series by Loess".
Regards,
Manish

Dvt:linegraph: series color problem.

hi all,
i am using dvt:lineGraph to show data of use account.now account are of two type saving and current.now on y axis i am grouping balance and account type and on x-axis transaction date.
one user can have multiple saving or current account.
problem is :
when particular user hav say 2 current and 1 saving acc.now 3 line get plotted safely but with 3 different color .what i want is 2 current acc's lines sould hav same color.
i tries using EL..but i am not able to find the account type for the particular series...
anybody hav any suggestions...:(:(
thanks
Dhiraj

hi ,
any help??...:(

Catalyst Express 500 series connection problems

Hello! our company is currently using two 500 series switch connected to eachother using the g1/1000mbits port, a cisco router is also plugged in to one of the switches for broadband internet access. After deployment the following problems came up, we are unable to use our wireless access point even when the port is set up as being "access point" using the smartports feature, we simply cant ping the access point no matter what port type we set on the switch and we keep having the error message on the router that it has denied connection from that device, my feeling is that for some reason i'm not aware of the router is blocking certain devices to transfer data no matter what type of port we define on the smartports feature. I cant find anyway or option on the router software to disable this blocking or filtering of the data in order to connect any devices i want normally without any restrictions. for some reason the switch is not accepting connections from the access point...
Any help would be much appreciated.
Fernando - London - UK

Hi, well, i did disabled STP but it didnt help, i'm going to post the network topology more exactely and the settings being used so its easier to get any help as i think i missed some points about our network :) ....so here it goes :
1. All the devices and client computers are using fixed ip addresses on the range 192.168.254.x
2. Topology :
Switch number 1 connected devices:
17 client computers connected
1 printer
1 cisco router (with dhcp disabled and using fixed ip too)
1 Netgear AP using set with DHCP
Switch number 2 connected devices:
10 client computer connected
Switch 1 and 2 are connected using the G1/1000mbits uplink port
Settings being used on BOTH switches (they are both catalyst 500,same software version) :
- default vlan1 is set and enabled
- STP enabled
- IGMP snooping enabled
- all ports are enabled and set to auto mode for speed and duplex
- port Gi1 that is used to connect both switches is set as "Switch" type with smartports.
- gateway (cisco router) ip address set
- security set to "low"
- STP settings on switch 1:
currents roots: VLAN1 , priority:32768 , root port: fa24 (where the router is connected), route path:38
- STP settings on switch 2:
currents roots: VLAN1 , priority:32768 , root port: Gi1 (uplink to switch 1), route path:42
switch 1 specific settings:
- the port where the AP is connected is set using smartports as "Access Point" and the port where the printer is connected is set as "Printer" also using smartports on the switch device manager software.
- the port where the cisco router is connected is set as "router" with smartports
Facts:
- I am able to ping all the devices on the network from any computers connected to both switches.
- I am able to ping the printer from any computer connected to both switches as well.
- When AP is connected directly to the cisco router wireless clients have access to internet with no problems
- all wired client computers on both switches connect to the internet using the router without problems.
Issues:
- Cannot ping the AP from any client computer on the network
- When printing from Switch 1 clients everything goes well, but when i print from clients on Switch 2 i am unable to print as its unable to connect to the printer, however i can ping the printer on the command-line !
- When i try to plug in the network cable from the AP to its designated port on Switch 1 the network crashes !
Error messages:
When trying to print from clients on Switch 2 or when try to connect and use AP on switch 1 i get or "access denied to device connecting to portxx" or i get an STP blocking error .
Hope the picture is clearer now.
thanks once more.
Fernando.

Oi me chamo Edinaia recentemente mandei meu iphone 3 gs para o conserto, funcionava normal o sinal ... agora não... será que problema esteja relacionado a antena?

Oi meu Chamo Edinaia recentemente mandei meu iphone 3 gs para o conserto...
e voltou com problemas ''no sinal'' sem serviço sempre.... será que está relacionado a antena?

ITunes store series pass problem

I can't seem to access a series pass on my iPad it keeps saying unable to connect to store. I have tried all the help items any ideas?
I've managed to download a different series pass item so I'm a little confused

I'm having the same problem, but have not found a solution yet

HELP - Series of problems since latest ATV update 2.3.1

The first problem occured as soon as I tried to sync ATV & itunes after the update. I opened up itunes and it 'froze' as soon as it started to sync with ATV, this happened 3 times. I disconnected ATV from itunes, opened itunes and then re-connected ATV and resynced all of my content (which took 3 hours!!).
Yesterday I opened up itunes and after a series of checks it finally launched but to my annoyance all of my playlists had dissapeared and lots of my content was missing. I have retrieved my missing content from my itunes folder but the playlists are gone, these include the 'standard' itunes playlists such as 'recently added', 'on the go' etc.
Apologies for the long winded post but this is causing me great frustration and any help with this would be greatly appreciated.

Having read through some posts on this forum I have come to the conclusion that one of the problems may be caused by genius playlists created on ATV. Since my original post I have done a fatory restore on ATV, then a software update to the latest version 2.3.1. I then re-synced with itunes and the problem of itunes freezing seems to have gone away. The only other issue I have now is that any purchases I made through the itunes store will not sync to ATV. I will have to contact apple to help me with this issue.
Hope this helps.
Steve

MSI 865PE Neo Series Restart Problem

Hello,
I have a problem on my MSI 865PE Neo Series Mobo when i restart my system using windows or by pressing ctrl+alt+del my pc won't restart and stay there forever on a black screen but when i press my reset button it will restart normally this is my one and only problem regarding this mobo... pls any help here. fix or any tips and suggestions...
(*by the way this is just my friends computer and im the one who builds it and maintain it...)
System Specs Of My Friend's PC:
MSI 865PE Neo Series Intel P4 Motherboard w/ HT Technology Support
Intel P4 @ 3GHz/800MHz FSB HT Technology
512MB DDR400
MSI NVIDIA GeForce FX 5700 @ 256MB DDR
550W PSU 12A-30

no guyz im using Windows XP Pro SP1 and its not a OS problem because the first time i boot the system i have no OS yet and then i press ctrl+alt+del then my system wont restart at all even in windows ive updated all drivers and mobo bios and increasing DDR Voltage to 2.8v and disabling HT has no changed at all any help would be appreciated... i think this is some problem with MSI mobo power management that it can't match ur psu so well unlike ASUS and GIGABYTE mobo runs perfectly fine. by the way its not my pc its my friend's pc and im the one who builds and hope to fix this one and only problem... everything else is ok except for the Restart Problem!!!!
My System Spec:
GIGABYTE GA-8INXP Intel E7205 Chipset P4 MB
Intel P4 @ 3GHz/500MHz FSB
1GB Dual Channel DDR266
ASUS ATI Radeon X800XT @ 256MB GDDRIII/AGP8x
Seagate 80GB SATA HDD
Maxtor 80GB IDE RAID HDD
Microsoft Windows XP Professional Edition @ Service Pack 2 RC1 (fully updated)
My Friend's Spec:
MSI 865PE Neo Series P4 MB
Intel P4 @ 3GHz/800MB FSB
512MB DDR400 CL2.5
MSI NVIDIA GeForce FX 5700 @ 256MB DDR/AGP8x
80GB IDE HDD (x2)
Microsoft Windows XP Professional Edition @ Service Pack 1 (fully updated)
*this is not a windows problem motherboard power management or bios settings bug here..
*its my first time to handle a MSI Motherboard
*and if any guyz out there need help regarding other problems or any problems in ur pc pm me in ym @ [email protected]

Series of problems

Similar Messages

Maybe you are looking for