Set the input cursor i.e. "set cursor" in ABAP

In ABAP Dynpro, I have the possibility to set the cursor to a specified input field using the "set cursor" command.
In ABAP Web Dynpro it seems that I always have to place the cursor first using the mouse. Is there an equivalent to "set cursor" in ABAP Web Dynpro?

you can use the following method REQUEST_FOCUS_ON_VIEW_ELEM of IF_WD_VIEW.
data: lv_v_elem type ref to if_wd_view_element.
lv_v_elem = view->get_element( 'INP_PAR_LIFNR' ).
if lv_v_elem is bound.
view->request_focus_on_view_elem( lv_v_elem ).
endif.

Similar Messages

HOW TO set the input range for analog in (DAQ)?

How can I set the input range of a - NI DAQ USB 6259 - analog voltage input?
I wish to control it directly in my VI. Is it possible to set different ranges for different input channels?
Thank you,
Roberto

duplicate post

How is to set the input range of PCI-MIO-16E-1 (6070E) to be 0 to +5V?

How is to set the input range of PCI-MIO-16E-1 (6070E) to be 0 to +5V? Thank you very much.

Hi x2am,
Here is a link to a document about setting input range limits.
DAQ Input Limits
Hope this helps!
Jeremy L.
National Instruments
Jeremy L.
National Instruments

HT2508 My amp has an USB input but when I attach my mac pro to it, and set the input to the USB setting, no sound comes out. I looked at the system settings, but none of them produce a different outcome. How can I send the music through the USB out to USB

My amp has an USB input but when I attach my mac pro to it, and set the input to the USB setting, no sound comes out. I looked at the system settings, but none of them produce a different outcome. How can I send the music through the USB out to USB in?

AFAIK cameras offer their own built-in format utility for inserted SD cards. You should use that. Otherwise, refer to the manual that came with your camera to determine precisely how your SD cards need to be formatted to work properly. Personally, I'd suggest Partition Scheme: MBR, and Filesystem: FAT32.
Try to limit the number of formats you perform on the SD cards, though, as you're reducing their lifespan. I believe formatting causes re-writes to a portion of the SD card that has fewer read/write cycles than the rest of the card as a whole.

How can you set the max row for a 'open cursor' in a stored proc?

I would like to know how can you set the maximum amount of row returned in a resultset coming from a stored proc?
You can do it via JDBC with cStatement.setMaxRows(10); but it works only for select that you do via JDBC...
I would like the same functionality using open cursor inside a stored proc...
Thanks...

is "where ROWNUM <= 10" the equivalent of "cStatement.setMaxRows(10);" because the ROWNUM as problem with the ORDER BY clause and the setMaxRows() as no problem...

Is there a way to re-set the default fade-in/out setting for all slides?

Hi all, I don't know why all objects on all the slides of my captivate project are set as transition-> fade in/fade out. The result is that every single slide fades out after 3 seconds, even before the learners can finish reading.
The only solution I know is to change each single object from transition->fade in/fade out to No Transitions. However, it takes thousands of clicks.
Does anyone know that there is a one-step solution to get rid of this default fade in/fade out settings?
Or was there something that I did wrong which caused this default fade in/fade out?
Thank you very much.

Hi all, not only are my objects set to no transition, I set the object defaults to rest of slide rather than specific time (located in the same window above. That way slide duration does not matter (unless you are doing autoplay and not using navigation.) This way when my audio lengthens the timeline all my objects are there for the full duration
Also, another tip, once you have set your objects styles and preferences the way you like them you can export both, and import them into any new project that you wish to use them in rather than reset all the time.

ABAP Program to set a set the QM Status of a set of REquests to RED

Hai friends,
I have an urgent requirement. I need to set the QM status of about 100 requests and delete them from 3 infoproviders. Can anyone help me out with an ABAP program to do it, if it is possible?
Regards,
Neha Solanki

Try modifying entries for tables RSREQDONE, RSMONICTAB whereever necessary.

Setting the Required Database AL32UTF8 Character Set

Hi,
How can I set the existing database character set to AL32UTF8 in order to use the database with Oracle Content DB.
How can I use the Database Configuration Assistant (DBCA) to re-create the database with the correct AL32UTF8 character set.
Regards
Boris

Of course you can change the characterset value, but you need to follow some good explanation as the metalink notes below :
Note:260192.1 - Changing WE8ISO8859P1/ WE8ISO8859P15 or WE8MSWIN1252 to (AL32)UTF8 with ALTER DATABASE CHARACTERSET
Note:227332.1 - NLS considerations in Import/Export - Frequently Asked Questions -
Nicolas.

How can I set the input volume of my sound card before starting my sound acquisition ? ( well how to use the appropriate dll )

I have the Volume control application , but it works for reading.. and note to select record , to set input line volume !!
thanks

Hello Guill,
If you are using LabVIEW, you can use SO_Volume.vi (not present in all LV versions).
If you are using CVI, the best way is to use Microsoft Windows SDK functions, look at multimedia functions on msdn.com
Hopes this help
Salissou ISSA
Applications Engineer
National Instruments France

Newbie question: How do I set the input for a series of audio recordings to be different, if I only have a 2 channel interface?

I am using a 2 channel interface (Apogee Duet) and I can record a voice and guitar track fine. My question is how do I record a third audio track after the fact? It seems when I attempt to record an additional track, say bass for example, Logic treats it as though it is on input 1 or 2 (which hardware wise it is of course) and merges them in a sense. I don't know how to make it a seperate independant track, despite the fact that it was recorded through an input that I also used to record something else on a diferent track.
Thanks in advance, I very much appreciate any help.

Thanks for the response. I know it sounds ridiculously basic. Yes I am creating a new track and selecting it. The third track appears in the arrange window, but changes to, for example, the third track affect the 1st. Doesn't matter if it's a 1/4 inch guitar or XLR mic. Yes I'm listening to the headphone output from the Duet.
I think the fundamental problem is my not understanding something about mono/stereo, or prehaps input and output settings. I just can't seem to find the appropriate controls/settings.

How to set the input and output of a subVI

I am trying to configure a subVI by following Chap. 7 of "LabVIEW fundamentals". But I stuck at "Building the connector pane".
My subvi is quite simple, just for testing purpose. I plan to do a summation and display the result. So I placed one numeric Add icon on the block diagram and a numeric Indicator on the front panel. I built a connector pane with three terminals, two for input and one for output.
But, how could I associate the terminals on connector pane with inputs and outputs of terminals on the block diagram? I wanna build a subVI, whose input are two numbers and display the summation on the subVI.
Forrest Sheng Bao, Ph.D.
Assistant Professor, Dept. of Electrical & Computer Engineering
University of Akron, Akron, OH, USA
https://sites.google.com/site/forrestbao/

Hi Forrest Bao,
use the right mouse key as often as you can in LabVIEW. It´s very helpful. If you right click on a link in the connector pane, then you can select to disconnect selected or all.
Mike
Message Edited by MikeS81 on 08-28-2008 01:33 PM

We have a HP Color LaserJet CP1510 printer, how do you re-set the language when it's set in foreign?

Our HP Printer CP1510 got set to a foreign language, haven't a clue what it is, and since we can't read it to figure out what it says we don't know which buttons to push to get it set back to English. Has anyone else encountered this?
Thanks.

Hello,
Thanks for the post. I've included a link below that may assist in getting this printer back to a factory state and allow you to reconfigure. Please note, bottom paragraph regarding the IP address after the reset. Good Luck!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01530973&tmp_track_link=ot_faqs/top_issues/en_u...
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

How do we set the incoming server on mail set up as it is grayed out?

Hi we are setting up an icloud email account, but we are unable to type in the incoming server field, how do we access this field?

You indicate that you are using OS X Lion. To set up iCloud mail, just open System Preferences > iCloud and tick Mail, so your mail account will be set up automatically on Mail

How to set the value to ADOBE form input filed...in WDP ABAP...very urgent.

Hi,
SET_ATTRIBUTE is not working for the adobe forms in WDP-ABAP. Is there any other funtion to set the value in the input field of adobe forms in WDP-ABAP.
Please let me know at the earliest
Thanks,
Kesav.

Hello,
set_attribute should work also in this case. The context element has to be bound to the given inputfield on the form.
Can you please check your binding on the form?
Kind regards,
Dezso

HCM F&P - How to set the field as Required based on drop down values

Hi Experts,
I have a requirement to set the Date field as mandatory when a particular value is selected in drop down list. I have already tried with MessageBox though it displays the error message but process moves further i.e. on clicking Check & Send button it throws an error message but still it moves further and i can see only Send button. Ideally it should halt there itself.
Thanks & Regards,
Jitesh Talreja

Thanks for your valuable inputs
Chintan
I have already tried this. It only highlight the field with the red border but still allow to move further.
Mukesh
Yes, we can definately control this from the backend but that would be the last option i should execute. Ideally, this is something to be controlled in front end itself
Poornima
By setting the field attrbiute Required will set the field mandatory as a whole irrespective of drop down values or any other UI element.
Regards,
Jitesh Talreja

Set the input cursor i.e. "set cursor" in ABAP

Similar Messages

Maybe you are looking for