Setting up the extreme and DSL modem

Hi guys,
just bought and upgraded to the new extreme base station and hooked up to the DSL modem, but couldn't get them to work.
Before, I had the 1st generation airport base station (snow) hooked up to the router and the router to the DSL modem. And now i just want to connect the new extreme base station to the SDL modem (SBC Yahoo)and no router involved. What changes do I have to make? PPoe or DHCP it seems that the extreme base cannnot establish coonection with the modem.
I've tried setting ppoe under system preference, put in my account name and password but it doesn't receive any IP address. Next to the airport signal on top of the screen, it shows a message" negotiate ppoe"
Anyway, I would appreciate if anyone canould point me the right direction before I call apple.
thanks!

What changes do I have to make? PPoe or DHCP...
What settings does your ISP use? What settings did you use on the router you were previously using? Those are the settings you need for the AirPort Extreme base station (AEBS).
I've tried setting ppoe under system preference...
If your ISP requires PPPoE you should enable it on the AEBS but disable it on all of your computers.

Similar Messages

Airport Extreme Base Station and DSL modem, IP address Conflict issues

I recently set up DSL service in my apartment. I have ATT yahoo DSL modem, and an Airport extreme base station plugged into it. The network works fine with my Vista PC connected to it, but when I try to connect my macbook to the network I get errors telling me the IP address the macbook wants to use is already in use, and my PC gives me an IP address conflict error.
The internet is fine, and the modem is configured automatically, so I think it must be a problem with the way the network is set up or the network settings on my macbook...
any ideas?

All,
I recently posted what I believe to be a similar/identical issue. See my post here: http://discussions.apple.com/thread.jspa?threadID=1378849
I have not changed my AEBS to "Off (Bridge Mode)" yet, because everything currently 'works' but I continue to get the occasional "Double NAT" warning suggesting I switch the AEBS to bridge mode. When this happens, I lose connection to the internet and need to unplugged both the AEBS and my modem to re-establish a connection to the internet and the external HD I have connected to the AEBS.
My question for Jmiller1138, do you continue to get the "Double NAT" warning even when you changed your AEBS to "Off (Bridge Mode)"? I am hesitant to change my AEBS to bridge mode since I'm assuming I'll need to totally reconfigure my entire network (meaning both the AirPort Extremes, my wireless HP printer, and my firewalls on my PCs).
The ignoring of the warning (i.e. closing the AirPort Utility without updating the AEBS) is what triggers the need to reset my AEBS and modem. Not fun.
I guess I'll just need to bite the bullet and set the AEBS to bridge mode . . . yes?

Is it possible to add a firewall Filter or Rule Set to the Extreme Router (802.11n)

Is it possible to add a firewall Filter or Rule Set to the setting for the Extreme Router (802.11n) like the following:
"ALLOW TCP/UDP IN/OUT to 208.67.222.222 or 208.67.220.220 on Port 53" and
"BLOCK TCP/UDP IN/OUT all IP addresses on Port 53"
The goal of this is to create a firewall rule to only allow DNS (TCP/UDP) to OpenDNS' servers and restrict all other DNS traffic to any other IPs.
Or, alternatively is there a way to configure same applied to the Network preferences on IMAC OS X?
Thanks and much appreciation to anyone who has any clue about this.

Sorry, I think you've got it backwards.
The concern is NOT that the child can make changes to our hardware/AEBS, or even our network software on my IMAC - nothing's been changed.
BUT, he changed the dns settings on his OWN device (ie chromebook) to google public server, accessed the AE using our home wifi network BUT bypassed our dns settings. Capeesh?
See: http://www.pocketables.com/2013/03/how-to-use-change-the-dns-settings-on-your-ch romebook-and-use-googles.html

How do I set up the "Objects and Attachments"

Hi .... I'm new at WorkFlow (and SAP for that matter) and have inherited a WF that is already built. In several of the steps I can see "Objects and Attachments" on the work item screen where a User can click to be directed to a transaction. For example, on one screen the User can click on "Incoming Invoice: 5105601690" to be directed to the Invoice Display Screen that is populated with information for that particular invoice (5105601690).
I am looking at the WF using TCode SWDD and cannot figure our how the original developer set this up. So my question is ..... for a particular WF step, how do you set up the "Objects and Attachments: area so that the User will be directed to a particular transaction when he/she clicks on it.
Thanks in advance, and sorry for such a "juvenile" question.
Dan A

Thanks for your reply Rajkumar,
I am looking at the screen you have directed me to. Business object is BUS2081 (actually it is ZMMWBS2081 which is a customized version BUS2081) Method is "Display" and Attribute is "InvoiceDocNumber". How do I know by looking at this that "Display" means Display Invoice? What if I wanted to display the PO instead?
Thanks for the "spoon feeding".
Dan A

How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

How can I recover an old/disused iCloud account. I was having some issues with my apple id so I restored my iPad, I am now stuck on the activation screen as I no longer use the iCloud account i used to set up the iPad and can't remember the address or pas

I have the same problem - it is maddening. I rely on this iPad for work so this is not just an annoyance! The above solutions of changing the appleid on the device or on the website do not work.
The old email address no longer exists - I haven't used it in a year probably and I no longer have the account. I logged into the appleid website and there is no trace of the old email address so there is nothing that can be deleted or changed there. On the iPad there is no trace of the old email address so nothing can be deleted there either. I have updated the iPad software and the same problem comes right back. Every 2 seconds I am asked to log in using the old non-existent email. The device is currently useless.
The only recent change to anything was the addition of an Apple TV device, which was set up using the correct login and password.
Does anyone have any ideas? The iPad has been backed up to the iCloud so presumably it now won't recognize the current iCloud account? So restoring may notbe an option?

TS1702 i downloaded the GV app to my iphone but i'm trying to set up the app and it says it can't connect to google when i try to sign in to my google account.... any ideas what's wrong? i can access my gmail account just fine with my gmail app on the sam

i downloaded the GV app to my iphone but i'm trying to set up the app and it says it can't connect to google when i try to sign in to my google account.... any ideas what's wrong? i can access my gmail account just fine with my gmail app on the same phone

What's a GV app?

Bought the iphone 5 today, and when i turned it on it made me set up the language and my origin of country. Then it made me set up wi fi settings but my wi fi settings are messed up! Now i can't proceed to press next! Please help!!

Bought the iphone 5 today, and when i turned it on it made me set up the language and my origin of country. Then it made me set up wi fi settings but my wi fi settings are messed up! Now i can't proceed to press next! Please help!!

No
It says ' Your ipj
your iphone could not be activated because the activation server cannot be reached. try connecting your iphone to itunes to activate it, or try again over the cellular connection in a couple of minutes. You can also try to activate using a Wi-Fi connection.'
HELP:(

Thank you all for the responses. By process of elimination, I think the problem is the connection to the express in between the extreme and dock. I bought another express and tried it at dock, no luck, I then replaced new express where the one is between

I have an airport extreme and express setup. My extreme is in my 2nd floor office with windows facing the water. My dock is about 250 ft away down a very steep hill. I have the express about 100 ft down the hill in an electrical waterproof box attached to a tree as high as I could install. The signal is weak and I'm thinking I might have to buy another express. Any thoughts on the best setup for me. I ultimately want to control speakers(hard wired in) down at the dock with my iphone. I have a receiver coming with airplay built in.
Thank you all for the responses. By process of elimination, I think the problem is the connection to the express in between the extreme and dock. I bought another express and tried it at dock, no luck, I then replaced new express where the one is between extreme and dock, no better. I unplugged the express between extreme and dock and there was no difference. So I believe I am connecting to the airport express or extreme that is inside the house. Again because when i approach express that is halfway I reconnect. so if you can understand my chaos, I believe the express in between is not really connecting to the extreme inside my house. Yes, No? So I need to know how to know if the express half way down the hill is getting the connection from the the extreme in the house. This is wearing me out!!!!!

You are asking several different questions. If you need to store your photos, music, and movies on an external volume, you certainly can. Any externally connected hard disk drive will work, connected either directly to your Mac or to your Time Capsule as a shared volume.
You should not rely upon using that as a backup device though. Although you certainly may use it for both purposes, it is a better idea to have dedicated backup devices for a variety of reasons not limited to redundancy. You would not want to simultaneously lose all your pictures as well as your backup. If they are all on the same device, that could happen. Furthermore, a backup cannot back up the volume on which it is running.
As for adding an Extreme or Express, using its LAN port for your iMac, and then enable Internet sharing so you can effectively use the iMac as a "hotspot", you can do that too, but I am unclear on what benefit you believe this arrangement would convey for you.
An Extreme's Guest network is separate from its Main network; that is the reason for having it.

How do you set up the stock and weather ticker on notifications?

How do you set up the stock and weather ticker on notifications?

The next question will be what weather and stock apps will display data in Notifications similar to an iPhone. Sure there are lots of apps available but nothing I found will duplicate the features found on the iPhone.

I just noticed that when I talk on skype, my friends can not hear me as clear. I went to sound setting on the mac and noticed that my voice was getting picked up to good regardless of chaning the setting. Has anyone got any idea??

I just noticed that when I talk on skype, my friends can not hear me as clear. I went to sound setting on the mac and noticed that my voice was getting picked up to good regardless of chaning the setting. Has anyone got any idea??

Basic troubleshooting from the User's Guide is reset, restart, restore. Has any of this been tried?
It is possible that dropping the device has caused the issue.... regardless, it's unlikely Apple would do a warranty exchange since there is obvious user damage.
If basic troubleshooting does not resolve the issue, take it to an Apple store for evaluation... if determined to be a hardware issue and you ask nicely, they may be able to assist you, but they may also only provide the option of an Out of Warranty replacement.

HT4528 I loaded the iphone update and now my gmail does not sync. I get a message that imap cannot connect. All my setting are the same and correct. Thoughts.

After loading the iphone update, I get a message that imap.gmail.com is not resopnding. All my setting are the same and are correct. My gmail works on my ipad. Thoughts.

Same thing happened to me. Called Verizon, they had me run updates and resync to the local tower (*228, option2). Took about 15 minutes over the phone to correct.

VM Specs to set up the QA and Prod

Hi,
Can any one please help me in setting up VM with hardware and software configurations to set up the QA and Prod.
i need VM Specs (hardware and software configurations ) to set up the QA and Prod?
Regards, Aboorva Raja R Please remember to mark the replies as answers if they help and unmark them if they provide no help.

The suggested hardware spec is as follows:
A computer with an Intel Pentium-compatible CPU that is:
1 GHz or higher for single processors
900 MHz or higher for double processors
700 MHz or higher for quad processors
Hyper-threading and dual-core processors are supported.
The 64-bit versions of BizTalk Server require a 64-bit operating system running on an x64-based system. Computers based on CPUs that are compatible with the AMD64
(x86-64) and Extended Memory 64-bit Technology (EM64T) processor architecture are considered x64-based systems.
BizTalk Server is not supported on Itanium-based systems.
Memory Minimum - 2 GB of RAM, but from experience its suggested to use atlest 8 for better performance.
Hard disk: Minimum 10 GB of available hard disk space for a complete installation including the operating system and all prerequisite software.
The hard disk must be NTFS formatted. But again from experience its suggested to use attest 50+GB.
And the following article from MSDN shall help you with the
Microsoft -Hardware and Software Requirements for BizTalk Server 2013
If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful by clicking the upward arrow mark next to my reply.

How do I set up Airport Extreme with cable modem and router?

Hi--
I'm having a house built and all of the wiring for TV, phone, and internet will be centralized in a closet. The cable modem can be placed there as well. In one room in the basement I want to use my Airport Extreme for my iMac and USB external hard drives. In another location of the basement, I'd like to set up a Time Capsule for another desktop and USB printer. If the cat5e comes out of the wall at each location, I "think" I need a router at the closet location. I also thought I might need an Airport Express upstairs on first or second floor to boost signal for my laptop. The house isn't that big so maybe that's overkill. So beyond the router question, do I want to set up a roaming network and have the Airport Express connected via ethernet or just wireless if the thought is that I need this? Finally, if I should connect cable modem to router to Airport Extreme, Time Capsule, etc., in what order and ports does the equipment get connected? Many thanks!!

Welcome to the discussions, Forum Girl!
It would be best to position the cable modem and main router in the central location like the closet if possible. The other devices would connect via ethernet to the wall jacks in each room.
If you could setup a "roaming" wireless network as you mention, this will give you better wireless performance and coverage. This is the way commercial establishments like airports, businesses, etc. are configured for wireless.
The order of connection would go something like this: ethernet connection > cable modem >main router>devices. Devices could be computers, routers, a backup device, etc. Since the Extreme has only 3 LAN ports for ethernet connections, you will also need to plan to install an "ethernet switch" near the location of the main router to provide enough ethernet jacks. If you are planning to use DirectTV, etc or your audio/video devices require ethernet connections (most new products do for updates and extra features), be sure to plan for that as well.
Make sure that CAT5e or CAT6 wiring is run so you will be able to take advantage of faster gigabit speeds.
Finally, it would be a good idea to work with an IT specialist to go over your plans to make sure all the bases are covered. This would be money well spent.

Connecting airport extreme, netgear dsl modem, windows 7, and Macbook pro

I'm having a problem connecting my airport extreme to my netgear modem, windows 7 pc and my Macbook Pro. Until a few days ago, I had a Westell wireless dsl modem and everything worked fine. Now, the only way I can connect to the internet is through my desktop pc and the hardwired modem.

If your goal is to extend/boost the range of your Netgear router with either or both of the AirPorts, this will not work wirelessly ... at least, not completely by wireless. That is because, WDS is not standard and each manufacturer has had creative license to implement it as they see fit for their products.
Instead, you have at least two other choices to use the Netgear (as the main Internet router) with the AirPorts:
Connect one AirPort directly to the Netgear by Ethernet, and then, configure both AirPorts for an extended wireless network. In this configuration, you would be running two separate wireless networks; one created by the Netgear, and the second the extended network created by the AirPorts.
Connect both AirPorts directly to the Netgear by Ethernet, and then, configure all of the routers for a roaming network. In this configuration, there would be a "single" wireless network where wireless network clients can literally roam from one router to another and still be on the "same" wireless network.

Setting up with Vonage and Comcast modems

I've tried twice to set up my TC to no avail. I know I'm not doing something right but am unsure what it is. I've read the manuals--I'm a bit challenged in these areas.
My current set up is: Comcast modem to Vonage modem; Vonage modem to Airport extreme, and, to a router for our home which is wired. What I've tried:
Comcast to Vonage to TC / router--the computers could not see TC or only saw it temporarily.
Comcast to TC to Vonage / router--No wireless, no internet, and lost Vonage phone service. Plus, I could not get the TC light to stop flashing amber.
I have enjoyed immensely the simplicity of Apple when setting up the wireless network. But I am stumped. What am I overlooking?
Thanks
The results of the

Let me check to see if I understand.
Are you referring to Time Capsule as assuming the role of the main router, which is currently a Linksys Etherfast DSL/Cable Router Model BEFSR41? So this router is no longer required?
Here's what I think you are proposing:
1. Comcast modem to WAN port on Time Capsule (replaces Linksys Etherfast)
2. Connect Vonage to LAN port on Time Capsule
3. Connect the second router (10/100 8-Port Workgroup Switch Model EZXS88W) to LAN Port on Time Capsule
4. Put the second router in bridge mode
The Airport Express would be removed in favor of Time Capsule so not sure what wireless preference is being referred to for the second routeer.

Setting up the extreme and DSL modem

Similar Messages

Maybe you are looking for