Setup new access point 1200

hi
i have problem in install new access point 1200
the access point now not connect to any device iam connect the access point using ethernet cable to PC to configure it i try to using GUI but i can not iam setup the PC with ip address 10.0.0.2 and GW 10.0.0.1 and i try to enter to access point but i can not
i try to use CLI and i connect the access point to PC using console cable and now iam enter to it after the access point start i try to enter to config ter but i can not i get error when i check the command i can not see this command and when i read the manual its tell me to setup ip address using command (lwapp ap ip address) and i try to save ip address using command wr mem or copy run start but i cannot i get error
in prevelig mode i get only this command
clear Reset functions8B5E500 00001537 61300D06 092A8648
clock Manage the system clock
crypto Encryption related commands.
debug Debugging functions
dir List files on a
led LED lock Lock the terminal
more Display the contents of a file
name-connection Name an existing network connection
no Disable debugging functions
ping Send echo messages
pwd Display current working directory
release Release a resource
reload Halt and perform a cold restart
rename Rename a file
renew Renew a resource
rmdir Remove existing directory
save Start to save raise_interrupt_level stack
send Send a message to other tty lines
set Set system parameter (not config)
show Show running system information
systat Display information about terminal lines
terminal Set terminal line parameters
test Test subsystems, memory, and interfaces
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
upgrade Upgrade software
verify Verify a file
where List active connections
how i can setup it and how i can enable the radio
when i see sh run i see that the ip address is dhcp
can any one help me please
thanks

Hi Nassem,
It looks like you ended up with a Lightweight AP (LAP Part#) instead of an IOS AP. This can be fixed;
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

Similar Messages

Dose access point 1200 aironet lightweight work stand alone

hi
i have question about access point 1200 aironet lightweight
my question is
dose access point 1200 aironet lightweight work stand alone or must connect to controler if its work stand alone how i can disable controller and how i can setup it
thanks

You will need a controller to configured an AP running the LWAPP image. If you need it to run standalone you can convert it to IOS with the process in this document.
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

Blackberry Z10 connection with an Aironet Cisco Access Point 1200

Hi everybody,
I'm trying without success a connection between a Blackberry Z10 and an Aironet Cisco Access Point 1200.
We have no BB Server, we would like just to connect the WIFI.
I've checked this points during the activation of the device:
There's no LEAP protocolle.
There's an EAP-Fast possibility.
There's Mac Address recognition possibility.
When we try to use the EAP-Fast possibility, we generate a .pac file, but i don't know where i can put this file so that the Blackberry recognize this file. I've search the whole day and didn't find anything... there's simply no explanation with the Z10 around the .pac file without a BB Server.
I've try the Mac Address recognition and it simply doesn't work (no error the search time is too long)
Every other older smartphones - Blackberry (there's 4 devices) are working.
Anyone have an idea about? a suggestion? a list of compatible WIFI Devices?
Thank you ahead.
Have a nice day.
Joel.

Sorry i don't understand your answer.
I'm not a developper but a system administrator.
I just would like to use a Balckberry Z10 with our Wifi/Router Aironet Access Point 1200.
not more.
Best regards,
Joel

How do i ensure the new access point is joined the controller or not

How do i ensure the new access point is joined the controller or not

To Verifying that Access Points Join the Controller or not there are two ways as below.
Please go through the step by step to find the APs joined state
When replacing a controller, you need to make sure that access points join the new controller.
Using the GUI to Verify that Access Points Join the Controller
Follow these steps to ensure that access points join the new controller.
Step 1 Follow these steps to configure the new controller as a master controller.
a. Click Controller > Advanced > Master Controller Mode to open the Master Controller Configuration page.
b. Check the Master Controller Mode check box.
c. Click Apply to commit your changes.
d. Click Save Configuration to save your changes.
Step 2 (Optional) Flush the ARP and MAC address tables within the network infrastructure. Ask your network administrator for more information about this step.
Step 3 Restart the access points.
Step 4 Once all the access points have joined the new controller, configure the controller not to be a master controller by unchecking the Master Controller Mode check box on the Master Controller Configuration page.
Using the CLI to Verify that Access Points Join the Controller
Follow these steps to ensure that access points join the new controller.
Step 1 To configure the new controller as a master controller, enter this command:
config network master-base enable
Step 2 (Optional) Flush the ARP and MAC address tables within the network infrastructure. Ask your network administrator for more information about this step.
Step 3 Restart the access points.

How to get a new Access Point to be seen by the controller

Hello All,
I have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller. I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch. After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). Looks encouraging so far.
Here is where I am stuck...
When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address. I want to be able to rename the AP to reflect where it will be used, but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc.
I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address. I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.
Is there something I'm missing like a "re-scan" that scan's all devices?
The AP is an AP 1131 AG
Thanks,
Jon

For console connetion you need console cable i attached image of it so you know which cable we are talking about. Just connet eithernet side to the connector i think on 1131 console port is on the right if you seeing it form back. Plug other side of cable to a laptop on serial connetor and use windows hyper terminal to access your access point. Once you connected via console you should be able to see whats going on on the console. Here is a quick link for setting up console connection with correct settings.
http://ciscogeek.org/setup-windows-hyper-terminal-to-access-routerfirewall-console/
Hope this helps you

User unable to connect to new access point AIR-CAP3502P-S-K9

Hi Guys,
In my branch there are 8 access points[ AIR-CAP3502I-S-K9 ] connected to Wireless controller which is been working fine since the beginning.. I had to add two more access points to this branch and after the failure, i realised this Access point [ AIR-CAP3502P-S-K9 ] is latest and it needs the minimum image 7.3.101.. So i did a upgrade on WLC 5508 and all 10 access points have joined successfully...
Issue am facing is when NEW users come under AP 9 and AP 10 get associated successfully, but the old users(Projetc Manager) who been in the branch for very long and able to get associated with other AP's [1 to 8] gets associated successfully with all old AP's but not with the new AP's..
Could please some one advise, why this strange behaviour... I googled for answer but am not getting any right solution...

Issue am facing is when NEW users come under AP 9 and AP 10 get associated successfully, but the old users(Projetc Manager) who been in the branch for very long and able to get associated with other AP's [1 to 8] gets associated successfully with all old AP's but not with the new AP's..
Do you have AP Groups configured?
The old wireless clients, are their drivers up to date?

IOS Upgrade Procedure for Access Point 1200 0r 1230 series

Greetings all - perhaps this is posted or on the site howveer I did not see it anywhere. I have several 1231 Access Points that have an IOS on it but I would like to upgrade the IOS to the newer version. Can anyone provide a link or procedure on how to perform this.. Thank you kindly in advance

Hi Pete,
Have you had a look at this;
Working with Software Images
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_configuration_guide_chapter09186a0080184aa2.html#1035507
Hope this helps!
Rob
Please remember to rate helpful posts.......

Amazon Q&A : E2500 - Setup as access point

Does this work as a wireless access point?

Yes, it does. This is a router with built in wireless access point. It is also possible to use the router as plain access point only.

How do I setup an Access Point/Repeater on FIOS

I have a MI424WR-GEN2 router/modem from Verizon. Since Verizon installed it in the basement, my wi-fi at various other points is not the strongest. I do have cat-5 in various parts of the house. So, I'd like to add one of my old routers to the network and have it act as an access point or repeater (not sure if there is a difference between the two designations). I'm technical enough to be dangerous and do damage but I wasn't having any luck doing this ... for one, I can't even figure out how to access it to program it since 192.168.1.1 is the verizon router.
I have three choices for a device:
(1) Linksys WRT54GS
(2) Linksys BEFW11S4
(3) Netgear RangeMAx DGND3300 (my preferred choice because it has B/G/N as options)
Help please!
Thank you!

Ok, it is working, more or less. But there seems to be a connectivity or reliability issue. For some reason, and it seems to only be on my laptop (but perhaps because the others in my house aren't on engough and haven't noticed an issue?).
I periodically lose connectivity but the network is not down. I turn off my laptop wi-fi, wait a few seconds, and turn it back on.
I suspect this is something to do with competing protocols ... I don't know, and Verizon didn't confirm, if their router support b/g AND n. The netgear supports b/g/n. Also, the Netgear is dual band. Right now, the netgear, as an access point, has both 2.4Ghz (11g) and 5Ghz (11n) SSIDs set to the same name. Should they be different? In which case, do we need an additional wi-fi to recognize? It doesn't appear as if I can disable one of them.
For the time being, the netgear access point is right next to the laptop. COuld the proximity cause a problem? I've never had that issue before but trying to identify anything!
Any thoughts?
Thanks!

HP photosmart 7520 connects to wrong access point and looses connection

I recently installed a remote wireless access point in an outbuilding. I'm using a router with the same SSID and password as my main router with the same security settings. Only the main router is set to issue IP addresses. The system works fine with two laptops, a desktop, an Ipad and an Ipod. It provides continuous connections from my house to the outbuilding. Only the HP Photosmart seems to be an issue. At first the system worked fine then after a couple of days it lost its connection. I tried to the Wireless Setup Wizzard with no success. The Wireless Network Test results indicated that MAC address filtering may be enabled. This is not the case, MAC filtering in not enabled on either router. The next morning the printer was fine and connected again. I suspect that it is detecting the remote router and trying to connect through it. During the setup a warning came up indicating that two routers were detected with the same SSID and Password and that the printer might try to connect to the wrong router. It should not matter since the remote router connects and is issued IP addresses through the main router. The only difference in the routers is the BSSID. This uses the same number as the MAC filtering address, so I suspect this may be the problem. Any suggestions on a work around. The only thing I have found that solves the problem is turning off the remote router.

Hello there -
Is it possible your new remote access point only supports the 5Ghz band for N connection, or that it's connected to your primary router through a wireless N connection in the 5Ghz band? The 7520 only supports 2.4Ghz N connections. If your primary access point supports both 2.4Ghz and 5Ghz, that is likely why it's able to connect there while it cannot connect to the new access point. Many newer laptops and iPad/pods utilize 5Ghz N, which would explain why they can connect and your 7520 cannot. I'd recommend moving the 7520 closer to the primary router and using AirPrint to send your jobs.
***I am an HP employee***
The comments above represent myself and do not reflect the opinions of HP.

Problem with PowerBook (but NOT MacBook) and two access points on network

I recently installed a wall-plugged ethernet adapter system (Netgear XE104 and XE103) and plugged a wireless access point (Netgear WPN802) into one of the adapters (in the part of our house where we lacked a wireless signal) in order to extend the range of our (DSL) wireless network. I configured this new access point--disabled DHCP, assigned an IP address to the access point that does not fall into the wireless router's IP adress range, put the wireless router and access point on different channels (6 and 11), and made sure the router and access point had the same SSID.
I have had no problems using the resulting setup with our new MacBook--everything goes as planned. BUT I am having a terrible time with my PowerBook G4. It has a really strong signal everywhere, but when I open my browser it says that I am not connected to the internet. The problem seems to be that my PowerBook refuses to change channels once it connects to one. I installed iStumbler to see if I could manually control which access point/channel the PowerBook uses, and, while I can track the signal strengths for both access points, I can't get my PowerBook to switch from one access point to the other.
I've tried just about everything I can think of. I suppose I could try giving a different SSID to the access point (and then try to switch with the airport menu in the toolbar), but I would like to avoid this if possible.
I would really appreciate any advice you have. Thank you!

Can you connect if you temporarily turn off WEP or WPA?
This will determine if it is a WEP or WPA issue.
Does your PC support WPA, from both a hardware and a software perspective?
The problem you are having probably lies with the encryption key.
Accessing a Airport Network with a Windows XP PC or laptop (with XP SP2)
http://tech.ifelix.net/1011.html
Accessing a Airport Network with a Windows XP PC or laptop (with XP SP1)
http://tech.ifelix.net/1010.html
Problems connecting an XP PC to an Airport Base Station
http://tech.ifelix.net/2002.html
iFelix

Is Cisco air-ap1230a a lightweight access point?

Is Cisco air-ap1230a a lightweight access point? Can it be use for the new CCNP training?
Thanks

Hi Bao,
The 1230 is not a Lightweight AP, but can be upgraded to LWAPP with the A Radio model listed below (Note that this model is EOS/EOL) this is probably not the best choice for your studies;
Solution Requirements
Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
All 1130AG access points
All 1240 AG access points
For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
if 802.11G, MP21G and MP31G are supported
if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
All 1310 AG access points
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
Cisco Aironet 1200 Series Access Point Ordering Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00800c9435.html
EOS & EOL for the Cisco Aironet 1200 Series 802.11a Access Points
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_eol_notice0900aecd801e5303.html
Understanding the Lightweight Access Point Protocol (LWAPP)
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd802c18ee.shtml
Lightweight Access Point FAQ
http://www.cisco.com/en/US/products/ps6306/products_qanda_item09186a00806a4da3.shtml
Lightweight AP (LAP) Registration to a Wireless LAN Controller (WLC)
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
**You are probably better off with something like the LAP 1131. Have a look here;
http://www.cisco.com/en/US/products/hw/wireless/products_category_buyers_guide.html#access_points
Hope this helps! I noticed your other post regarding the WLC suggestions and have responded there as well :)
Rob

E52 - after update cannot add access points

Can anyone help plz? I updated firmware to 054.003 but now I cannot add access points for wap/mms/internet! The setup wizard only gives me the option to add an email address only...before update I could get operator settings which is not the case now. Can anyone help? My cell phone carrier is ORANGE IL.
Thanks in advance.
mike

I upgraded an unbranded E52 last night to 054.003 and didn't have any problem adding new access points that the operator (in this case vodafone UK) pushed out. Suggest maybe a hard reset on the phone?

N95 Wifi, home network and hidden access points

Hello-
Just picked up a N95 and having some problems. First, my home network doesn't broadcast a SSID. I stumbled across the home network option and was able to configure it. However, it's never an option when I need an internet connection; e.g., it never shows up in the wlan list.
So, how do I congigure a hidden access point so I can use it? The user guide says you should be able to do it manually, but doesn't go into any details.
Secondly, exactly what is the home network setting for and why is it separate from the other wlan settings?
Thanks,
Jay

Jay,
I too have a hidden network (SSID not broadcast), the N95 seems to have a problem with this. It may or may not show up on the active standby screen (on my Voda N95, it shows up when I take my sim out!).
To configure your accesss point :-
Tools / Settings / Connection / Access Points
then Options / New access point
Connection name
(enter a name, whatever you want to call it)
Data bearer
=wireless LAN
WLAN network name
(enter your SSID here)
Network Status
(public or hidden)
WLAN network mode
(Infrastructure or ad-hoc. If you're using a router, infracstructure should be the one you want)
WLAN security mode
(Open, WEP, 802.1x or WPA2. Check your router)
WLAN security settings
WPA/WPA2
EAP or Pre-shared key (consult your router)
EAP plug-in settings or Pre-shared key
(which one you get depends on what you set above)
WPA2 only mode
(leave alone)
Having done all this it still won't show on the active-standy screen (at least it doesn't on mine) in the WLAN section BUT if you know try and surf the web it should ask which access point you want to use - assuming you've got it set to 'always ask'. What this seems to do is only list the connections that it can find (i.e if you've got a 'Starbucks' and a 'home' connection defined, it'll only show 'home' at home and 'Starbucks' when you're getting your latte. The standby screen may show, how to decribe it, a four leaf clover near to the battery level indicator, this is the indication that it's either found or connected to your wireless lan.
I think the 'Home netw.' option is for use with the Home Media Server application supplied on the CD. I haven't tried it so can't confirm for sure.
Hope this helps,
Simon
E&OE
Sony CMD-Z1, Nokia 8110, Nokia 6210, Nokia 6610 (returned within a week), Nokia 6600 (twice), N95, 3109c & N97.

Is there any way I can control which specific access point I connect (and stay connected) to from amongst a set of access points with the same SSID?

I'm working from a boat in a harbor in which the ISP has deployed numerous access points around the periphery. All the access points share the same SSID and each is configured to use either channel 1, 6 or 11. From my location, there are over a dozen of these access points "visible" (based on the the output of WiFi Scanner) with a range of RSSI and S/N values that vary over time.
The ISP has told me that the quality of my connection should be "perfectly fine" for any access point with an RSSI value better than -75, but I know from experience that my connection quality is miserable (i.e. < 50Kbps download) for almost all of these, including those with RSSI values better than -75. There is at least one exception, however, which gives me on the order of 2Mbps download, which is "great" in this context.
I've tried using a more powerful USB antenna plugged into my MacBook Air (mid 2011), but as far as I can tell, it really doesn't make much difference. Neither does my location within the boat. The overriding factor seems to be which access point I happen to connect up to.
I should point out that the closest access points are about 75 yards away, with many of them being several hundred yards away or more. I'm guessing that even though the signal strength of some of the distant access points is causing them to get "chosen" some times, the results are unacceptable due to the distance.
I'm hoping that I can determine, through experimentation, which access point(s) provide(s) acceptable performance and then configure my Mac to limit my connection to those points through whatever mechanism I need to use (e.g. channel, MAC id, etc.).

Establishing a wireless connection with a client computer is left to the access point for various reasons. One reason that your Mac may not connect to the strongest access point is that it may have reached a limit of the number of clients it can serve, leaving it unable to accept a connection with another. The limit may not be very large.
Suppose that happens, and your Mac establishes a connection with a more distant access point having a weaker signal. Then, suppose a client drops off the network. Doesn't this mean your Mac will switch to the stronger access point? Not necessarily. The throughput delivered to and from your Mac would have to drop below a threshold specified in the AP for it to drop the client, leaving your Mac free to connect with another one. The reason for this is to prevent rapid switching from one AP to another in an area in which two signals are of approximately equal quality. If that were to occur the frequent and repetitive handshaking between the two devices would slow throughput to zero.
In an environment in which several access points are broadcasting the same SSID, Apple provides no insight as to how it determines which access point to choose. This is the reason I suspect this "choice" is a function of the router, or access point. The connection originates with it, not the Mac.
Now, what would solve your dilemma would be to determine a way to control the access point with which your Mac connects, by specifying the access point's unique MAC address for example. In this happy circumstance, you could maintain an editable "whitelist" or "blacklist" of the harbor's access points and be able to choose which among them you prefer.
I do not believe OS X maintains such a record of MAC addresses though, only those of the routers it uses. If I am correct about that, such a solution is unlikely to exist. Don't let that discourage you from searching for one though... I would concentrate on something like "selecting access point by specific MAC address".
I did find this patent application though:
Roaming Network Stations Using A Mac Address Identifier To Select New Access Point
Perhaps it's a start

Setup new access point 1200

Similar Messages

Maybe you are looking for