SM bus and network controller problem

Hi, 
I have the above notepad but I cannot connect to the Internet.
In the device manager it shows  yellow triangles with a "!" for :
- network controller
- SM  Bus Controller
Where can I find the drivers for them?
I tried to put several drivers. 
But most of the time  a message came saying : "this computer does no meet the minimum requirements for installing the software"
Can anyone help ?
Thanks in advance.

Hi:
See my last reply to your other post...
http://h30434.www3.hp.com/t5/Notebook-Hardware/Missing-drivers-no-Internet-connection/m-p/4945051#M1...

Similar Messages

  • T42 Ethernet and Network controller problems

    I am fairly new to computers and obtained a T42 for my grandson. Please bear with me as I am rather Techno challenged and battled now for 2 days getting internet connection. Had to do a clean XP SP2 installation and landed up with a host of Other devices issues with Yellow Question marks. Have downloaded most drivers from http://support.lenovo.com/en_US/downloads with various success. Need serious help here please.
    In Device manager I am sitting with two unresolved issues under Other Devices
    Ethernet Controller PCI\VEN_14E4&DEV_167D&SUBSYS_05771014&REV11\4&111A1FD8&0&00E0
    AND
    Network Controller PCI\VEN_8086&DEV_4224&SUSYS_1011808&REV_05\4&AD1B67F&0&10F0
     I have downloaded various drivers but still cannot get them to work. Not sure which of the drivers to use.
    In another forum somebody replied
    The Intel PRO/1000 is an ethernet controller. Once you get that installed and establish a network connection, you can download and install MS dotnetfx and Lenovo System Update which will download and install all the other drivers automatically. Or just download them yourself and manually install them.
    Not very helpful as I could not figure ou thow to install as the drivers that I downloaded did not fix this and no further help from them when I questioned this
    Please if someone here will give us some step by step directions. The model is 2373-L77 if that will help
    Solved!
    Go to Solution.

    raycomp schrieb:.
    Ethernet Controller PCI\VEN_14E4&DEV_167D&SUBSYS_05771014&REV11\4&111A1FD8&0&00E0
    AND
    Network Controller PCI\VEN_8086&DEV_4224&SUSYS_1011808&REV_05\4&AD1B67F&0&10F0
     I have downloaded various drivers but still cannot get them to work. Not sure which of the drivers to use.
    Checked the "DEV_" # on www.pcidatabase.com
    upper: Broadcom NetXtreme Gigabit Ethernet driver (it seems, you have a T43-System Board in your T42 or you have a T43).
    lower: 802.11a/b/g WLan adapter driver (Intel 2915 Wireless LAN adapter)
    Please find the installation instructions on the linked pages. Executing the downloaded packages extracts them only to C:\DRIVERS\WIN\xxx.
    Starting there you'll need to execute the setup as described on the download page.
    My home-forum: http://www.thinkpad-forum.de
    Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
    My ThinkPad-Collection

  • Unable to install lan realtek rtl8101 and network controller driver on windows server 2008

    Hi Guys,
    i am trying to install realtek rtl 8101 f amily driver and network controller driver on windows server 2008 but unable to install.
    Hp device Model.:- hp pavilion g4 1303au
    Model no.:- 5c03213jsh
    network controller Device ID: PCI\VEN_168C&DEV_0032&SUBSYS_1785103C&REV_01\4&211965BF&0&0020
    Name: PCI Device
    Device ID: PCI\VEN_10EC&DEV_5209&SUBSYS_3564103C&REV_01\4&34BC5A71&0&0030
    Name: SM Bus Controller
    Device ID: PCI\VEN_1022&DEV_780B&SUBSYS_3564103C&REV_13\3&2411E6FE&0&A0
    thanks,
    Amit Rai

    Hi:
    SMBus controller:
    Here is what I have done...I have zipped up and attached below under Attachments, the raw smbus controller driver files for you to unzip and manually install. 
    Download and unzip the file.
    Go to the device manager and click on the smbus controller needing drivers.  Click on the driver tab.  Click on Update Driver.
    Select the Browse my computer for driver software option and browse to the driver folder that you unzipped.
    Make sure the Include Subfolders box is checked and the driver should install.  Then reboot.
    Ethernet:  Download and install the 1st driver on the list.
    http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTy...
    Card reader (PCI dev.):  Download and install the first driver on the list.
    http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=15&PFid=25&Level=4&Conn=3&DownT...
    Wireless:  You will have to try the Vista driver for the Atheros wireless card...
    http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5060882&sp...
    Attachments:
    sp66185.zip ‏7 KB

  • PCI Device and Network Controller uninstalle​d

    Having problems with downloading a pci device and network controller driver for presario cq57? Need help. my hardware id is PCI\VEN_10EC&DEV_5209&SUBSYS_3577103C&REV_01 

    Hi:
    You need to install the Realtek Card Reader driver from your notebook's support and driver page for the PCI device.
    Please  do the following so I can find out what model wireless card your model uses...
    Go to the device manager, find the Other Devices category, and click on the Network Controller needing drivers.
    Then click on the Details tab at the top of the network controller window.
    Now you see a Property drop down list and it is defaulted to Device Description.
    Drop down on that and select the second item on the list (Hardware ID's).
    Post the top string of characters that begin with PCI\VEN.

  • PCI devices and network controller

    Hi there can anybody tell on hoe to install the PCI device driver and the network controller please as these two devices is marked with an ? in the devices managers windows
    Thanks

    Subject: Re: PCI devices and network controller (Satellite SM 30 X-165)
    Good morning
    I have a problem i bougt a laptop in china but to translate it thay reprogramed everything and my modem was desinstaled, i dont exactly know which model it is, its a toshiba satellite and the mothem comes whit a ? (yellow question marc) and the name it apears is modem PCI
    could you help me
    Message was edited by: andres_pedroza

  • T41 has Network Controller problem

    I was given a T41 2373-7JU that I loaded with XP Pro. My problem is it will not  connect to the internet via it's browser. In Device Manager it shows a Network Controller problem and I've been unable to correct this no matter how many different drivers I've tried. Also, how do I tell if there's an internal  wireless card inside?  It did connect to the internet earlier today using my USB adaptor but now I can't even do that anymore. I've tried a dozen or so solutions without any success so where should I go from here?

    Hi and welcome to the forum!
    Following are the drivers you need for Ethernet and wifi card (and yes, as per support page there's an internal card installed in your system):-
    http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62922
    http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-42683
    To install the drivers successfully, you need to run the .exe setups from C:\Drivers.... for each device after the first setup completes.
    For ethernet, the setup is in C:\DRIVERS\Win\ETHERNET\PRO1000\Win32 and for wifi C:\DRIVERS\WLLANCSC.
    Hope this helps.
    Maliha (I don't work for lenovo)
    ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
    IdeaPad: U350
    Apple:- Macbook Air [Snow Leopard]
    Did someone help you today? Compliment them with a Kudos!
    Was your question answered today? Mark it as an Accepted Solution! 
      Lenovo Deutsche Community     Lenovo Comunidad en Español 
    Visit my YouTube Channel

  • Replaced hard drive need ethernet and network controller

    Hello
    I replaced the hard drive on my satellite L655.  I installed windows and used my existing key code.  The laptop is telling me I have no ethernet and network controller.  I have tried to find the correct drivers. Since I am starting the computer from scratch do I need to install other drivers as well?  Please help.
    Thanks
    Heidi 
    Solved!
    Go to Solution.

    I'm so sorry, Heidi. I misread your first message. I thought you had restored the hard disk to its original out-of-the-box contents using Toshiba recovery media.
    That's the best thing to do. All the drivers and utilities are properly preinstalled. Windows is preactivated.
    If you failed to burn recovery discs, you can obtain them from Toshiba. Scroll down to Get Recovery Media here .
    For instructions, see the section Restoring from recovery DVDs/media, which begins on p. 71 of the User's Guide.
       Satellite L640/L650 Series User’s Guide
    If you have problems with drivers after doing that, see my previous message.
    -Jerry

  • NVIDIA nForce Networking Controller problem

    Hi, I am a new user of Solaris and Linux and I am having a problem with my internet connection under solaris.... i was reading other messages in the forum and apparently solaris doesn't detect my network adapter because when i run ifconfig -a it only shows lo0....
    I went to nvidia.com but the drivers on their website are only for the graphics card... where can i get the requiered drivers (and how do i install them under solaris) for my internet connection to work???
    i have a NVIDIA nForce Networking Controller and connect to the internet using road runner trough a router...
    thanks...
    Javisam376

    Hi, I am a new user of Solaris and Linux and and I am having a problem with my internet connection under solaris...<snip>
    Javisam376
    Hi,
    Same problem here Javisam376, but I am on an AMD x64 platform, and wondered if that might be the reason why the Solaris Express Developer Edition was unable to see the NVIDIA nForce Networking Controller, so I wonder which platform you're on (32 or 64-bits?) A general Google search for "Solaris NVIDIA nForce Networking problem" gave a fair number of hits, so the problem, seems well known, but no solutions were suggested by anybody, as far as I could see(!?)
    But it seems the Linux community has the same problem, since I found this posting on LinuxQuestions.org (http://www.linuxquestions.org/questions/showthread.php?t=471094):
    "I just finished installing Red Hat 9 on my machine, which is running off of an AMD/NVIDIA nForce2 chipset mobo that has integrated ethernet. I was trying to set up my network connection, but was unable to locate the nvida ethernet controller in the Network app/Network Configuration Wizard. So I went on to nvidia's site and downloaded the x86 linux driver (using my other machine) and used a cd to pop it into the other comp... Saved it to the desktop,
    then terminaled: sh NFORCE-Linux-x86-1.0-0310-pkg1.run.
    It took me through a setup screen where I 'installed a audio and ethernet driver'. I checked the Network wiz again, still no entry for it. So I randomly clicked the hardware browser, and IT lists the 'nForce2 Ethernet Controller' under network devices, but I can't configure it from this screen. Anyway, I would seriously appreciate any help with this. I need to get internet access on this machine quick, so this is drivin' me crazy."
    Message was edited by:
    troruud

  • Probems with msi 875p neo Fis2r and network controller driver

    Hi guys just wondering if anyone could help me with my msi 875p neo FIS2R and problems with the network controller driver/network card.
    I'm running xp on a computer my nextdoor neighbour gave me. I got it working fine  with service pack 3 installed but then installed a bunch of windows updates last night and the computer would switch itself off before windows could start. Now I reinstalled xp and unfortunately it does not recognise the network controller/card at all now. I tried installing the intel network controller drivers but it stopped because it said no intel adapter/card was installed/present. Could anyone please help with suggestions? I tried running everest and under newtwork it doesnt list intel network adapters but I'm pretty certain it is. Again any suggestions?
    --------[ EVEREST Home Edition (c) 2003-2005 Lavalys, Inc. ]
        Computer:
          Operating System                                  Microsoft Windows XP Professional
          OS Service Pack                                   Service Pack 3
          DirectX                                           4.09.00.0904 (DirectX 9.0c)
        Motherboard:
          CPU Type                                          Intel Pentium 4, 2800 MHz (14 x 200)
          Motherboard Name                                  MSI 875P Neo-FIS2R (MS-6758)  (5 PCI, 1 AGP, 4 DDR DIMM, Audio, Gigabit LAN, IEEE-1394)
          Motherboard Chipset                               Intel Canterwood i875P
          System Memory                                     1024 MB  (PC3200 DDR SDRAM)
          BIOS Type                                         AMI (10/11/04)
        Partitions:
          C: (NTFS)                                         238464 MB (200326 MB free)
    --------[ DMI ]---------------------------------------------------------------------------------------------------------
      [ BIOS ]
        BIOS Properties:
          Vendor                                            American Megatrends Inc.
          Version                                           V2.4
          Release Date                                      10/11/2004
          Size                                              512 KB
          Boot Devices                                      Floppy Disk, Hard Disk, CD-ROM, ATAPI ZIP, LS-120
          Capabilities                                      Flash BIOS, Shadow BIOS, Selectable Boot, EDD, BBS
          Supported Standards                               DMI, APM, ACPI, ESCD, PnP
          Expansion Capabilities                            ISA, PCI, AGP, USB
      [ System ]
        System Properties:
          Manufacturer                                      MICRO-STAR INC.
          Product                                           MS-6758
          Version                                           00C
          Serial Number                                     00000000
          Wake-Up Type                                      Modem Ring
      [ Motherboard ]
        Motherboard Properties:
          Manufacturer                                      MICRO-STAR INC.
          Product                                           MS-6758
          Version                                           00C
          Serial Number                                     00000000
      [ Processors / Intel(R) Pentium(R) 4 Processor ]
        Processor Properties:
          Manufacturer                                      Intel
          Version                                           Intel(R) Pentium(R) 4 Processor
          External Clock                                    200 MHz
          Maximum Clock                                     4000 MHz
          Current Clock                                     2800 MHz
          Type                                              Central Processor
          Voltage                                           3.3 V, 2.9 V
          Status                                            Enabled
          Socket Designation                                FC-478
        Network adapters:
          Direct Parallel                                   5.1.2535.0
          WAN Miniport (IP)                                 5.1.2535.0
          WAN Miniport (IP) - Packet Scheduler Miniport     5.1.2535.0
          WAN Miniport (L2TP)                               5.1.2535.0
          WAN Miniport (PPPOE)                              5.1.2535.0
          WAN Miniport (PPTP)                               5.1.2535.0
     

    Quote from: Jack t.N. on 14-November-09, 08:00:05
    Clear CMOS with your PSU unplugged from A/C power.  Then load "Optimized Defaults" in BIOS and retest.
    thanks jimi... jack
    will try that and post later if it worked... ive never cleared cmos, this sort of thing is relatively new to me but thanks again

  • Yellow mark - PCI Device" and "Network controller" on Satellite A100-787

    There is a yellow mark in the device manager for a driver called "PCI Device" and also for "Network controller" although the network connection (LAN) is working well and all other functions of the computer seem to be working well.
    What are those devices??

    Regarding the LAN driver, it is installed and working properly (the wired one). The wireless driver is provided by Atheros which I installed from its own setup file and it didnt give me any error so I assume it is installed well although I havent tested the wireless connection yet. I am going to do that shortly.
    As for the PCI device, the card reader is able to read Sony memory stick and one type of SD card with certain teeth arrangement but not another card with a different teeth type. I dont know why it is the case. so this remains a mistery to me.

  • Help! PCI Communications controller and network controller

    please tell me what to download,heres my ids:
    PCI:
    PCI\VEN_8086&DEV_3B64&SUBSYS_3658103C&REV_06
    PCI\VEN_8086&DEV_3B64&SUBSYS_3658103C
    PCI\VEN_8086&DEV_3B64&CC_078000
    PCI\VEN_8086&DEV_3B64&CC_0780
    Network COntroller:
    PCI\VEN_8086&DEV_0084&SUBSYS_13158086&REV_00
    PCI\VEN_8086&DEV_0084&SUBSYS_13158086
    PCI\VEN_8086&DEV_0084&CC_028000
    PCI\VEN_8086&DEV_0084&CC_0280

    When requesting assistance, please provide the complete model name and product number (p/n) of the HP computer in question. HP/Compaq makes thousands of models of computers. Without this information it may be difficult or impossible to assist you in resolving your issue.
    The above requested information can be found on the bottom of your computer, inside the battery compartment or on the startup BIOS screen. Please see How Do I Find My Model Number or Product Number? for more assistance locating this information. DO NOT include your serial number. Please enter the model/product information into HP's Online Consumer Support page and post it here for our review.
    In addition to the above requested information, please provide the name and bit version of the operating systemyou require drivers for.
    PCI\VEN_8086&DEV_3B64&SUBSYS_3658103C&REV_06 = Intel Management Engine Interface
    PCI\VEN_8086&DEV_0084&SUBSYS_13158086&REV_00 = Intel(R) WiFi Link 1000 BGN (Please select the correct driver for your OS)
    If you have any further questions, please don't hesitate to ask.
    Please click the White KUDOS "Thumbs Up" to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • Missing Ethernet, PCI, and Network Controller Drivers

    I recently reinstalled Windows on my fiance's laptop, and now it wont connect to wi/fi.  The device manager is showing that there is no drivers for the Ethernet controller, PCI Device, or Network controller.   How do I fix this? Thanks!

     Hi, Network controllerhttp://ftp.hp.com/pub/softpaq/sp53501-54000/sp53753.exe Ethernet controllerhttp://ftp.hp.com/pub/softpaq/sp52001-52500/sp52421.exe PCI Devicehttp://ftp.hp.com/pub/softpaq/sp52001-52500/sp52186.exe  Regards

  • New logic board and network connection problems

    My late 2007 MBP just had a new logic board installed. I have home and work wireless networks that are configured to connect automatically. This always worked flawlessly in the past. My MBP would find the network, connect and all was well. Since I've had the new logic board I'm having issues. The wireless network will be detected but an IP address is not assigned so I can't get on the network or internet. Both my home and work networks were set to assign a specific IP address to my computer. The MAC address detected by the router is correct, at least according to System Preferences.
    The only way I can connect is to disable the firewall (Allow all incoming connections). When I do this I connect immediately to the network and everything works as normal. I can even turn the firewall back on and everything will be fine, that is until I leave work and turn the computer on at home. Then I have to go through this again. And then again when I go to work in the morning. I've tried deleting my router profile and resetting from scratch, deleting the network profiles in System Preferences and re-detecting. I don't know what else to try. It's an annoying problem.
    Any suggestions?
    Thanks.
    Kevin

    I think I have it fixed. One of the solutions I read about had to do with the 10.5.7 upgrade. I have always installed the smaller upgrades, not the larger "combo" upgrades. One tip suggested installing the full combo upgrade because, among other things, it re-creates two specific files that control how the computer interacts with the network. I installed the combo upgrade last Friday and connected without difficulty to the network at my office this morning. If I connect just as easily when I get home tonight I will consider the problem solved.
    Cheers!
    Kevin

  • 5800 XM WPA-PSK and network profiles problem

    Hi,
    I've just purchased a 5800XM phone, with the idea of setting up my personal email account on the device, using my office's network access point.
    The access point / router is a Comtrend 5361. The SSID is set to hidden (no broadcast), and the security is set to WPA-PSK (pre-shared key).
    On the Nokia phone I go to 'Settings -> Connectivity -> Wireless LAN' and choose 'Other (hidden netw.)'.
    Then I choose 'Connect', set the WLAN network name, the phone shows a message 'No WLAN network found', but then prompts to choose network mode (Infrastructure - Hidden),  and then password. It connects succesfully and asks for storing the network profile under offline mode, I tell it to do so, and the new profile appears under 'Network destinations -> Internet'. So until now everything seems ok.
    The problem is that after the phone disconnects from the internet, the stored profile seems to be useless, since the phone never connects automatically even if the AP is available and always shows 'Search for WLAN'. In the list the hidden access point never shows up so the only choice is repeating the steps that I mentioned above, creating a new profile every time I want to surt the net.
    Is there a solution to this, or a third party software that can do the trick?, I have OS V21.0.25, custom version 21.0.025.219.06 from Vodafone, no updates available as of today, but I've tested it with a phone that has the latest OS v30 and it shows the same behavior.
    I can't change the access point settings, so I must stick to WPA and hidden SSID, so for me this is almost a deal breaker.

    Ok, I was testing the wifi part without a sim card inserted, with a sim, the phone connects to the profile properly, but without the sim it has an odd behavior, not loading the profile and wrongly stating that it can't connect when it does (but disconnects randomly).
    So the problem is that wireless lan management doesn't work properly without a sim card.

  • Windows, RAC and network card problems... ?

    Dear friends,
    I've a problem! :)
    Here are some info:
    Node Hardware:
         Processor: Intel(R) Xeon(R) CPU E7430 @2.13GHz (2 processors)
         Installed memory(RAM): 52.0 GB
         System type: 64-bit OS
         Windows edition: Windows server 2008 R2 Enterprise
    Network cards (Shown by WIN):
         PublicLAN: HP NC373i Multifunction Gigabit Server Adapter
         PrivateLAN: HP NC373T PCle Multifunction Gig Server Adapter
         Offline: HP NC373T PCIe Multifunction Gig Server Adapter
    Software:
         Windows 2008 R2 Enterprise (Very last updates from MS)
         Oracle RAC 11.2.0.2.0 (Clusterware, DB) – 2 nodes
    Environment:
         AD network. Everything is MS based.
    Problem description:
    During RAC installation, company had only one network card (server network card, per node). Installation was successfully finished. RAC was/is in production. Has some problems, but noting for alarm.
    This days, we get other network cards. (purpose: network redundancy).
    RAC shutdown was clean.
    Network card inserted to nodes by OS Admin.
    Nodes was started up... and...
    OS Admin disabled network card immediately after logon screen was available... but to late...
    Windows changed network card order!!! PublicLAN was not at the first place when Cluster started (Network and sharing center -> change adapter settings -> Advanced (from menu) -> Advanced Settings -> Adapters and Bindings)!!! (I found in logs that MAC address changed at this point!)
    Cluster started hardware reconfiguration... and... we could not stop CW till starting up finished... ! After stopping CW again, we set PublicLan at first place, and every win setting was as at the moment of installation.
    Cluster was started again, DB, OEM too...
    Everything is working. Client can connect to DB, applications work well... but...
    Damage is done... now we have totally new IP situation inside... changes are saved to the DNS, too!!!
    Before inserting network card IP settings (nslookup from any client) :
    rac1 192.168.217.60
    rac1-vip 192.168.217.62
    rac2 192.168.217.61
    rac2-vip 192.168.217.63
    rac-scan 192.168.217.64
    192.168.217.65
    192.168.217.66
    After this incident (nslookup from any client):
    rac1 192.168.217.60
    192.168.217.62
    192.168.217.64
    192.168.217.66
    rac2 192.168.217.61
    192.168.217.63
    192.168.217.65
    192.168.217.66
    VIP and SCAN IP address are the same as before...
    nslookup show as that rac1,rac2,rac-scan change IP addresses in round-robin scenario!!!
    We stopped RAC couple of time and OS Admin cleared DNS records (both zone)... but every start of cluster make changes again in DNS.
    Other "side-effects":
    Some cluster commands, invoked from CMD, fire errors (lsnodes, cluvfy comp nodecon -n rac1,rac2).
    Configuration files seem to be correct (listeners, scan, scan_listeners, etc). srvctl and crsctl command are working without errors. oifcfg too.
    Logs are full of errors (like: ASM could not be reached... no listener)
    Listener(s) stop working sometime...
    Relocation of resource are not possible.
    Well, I mentioned the most important things... other alerts and errors in logs are present, but everything is connected with this issue, I think...
    As I said: RAC working. Clusterware, DB, OEM, connections, applications, backup... everything look good... but we have a problem!!!
    Any ideas, any suggestion, any link, any advice, anything are welcome!
    Thanks!
    PS.
    Metalink haven't any document about this... I've found a lot of examples for changing IP's, interfaces, interconnection... but noting about fixing problem!

    I'm having the same issue. My desktop pc keeps dropping the connection to my network (airport extreme router) while the rest of my devices (macbook pro, xbox, mac mini) still stay connected. The pc never had this issue prior to installing Windows 7 so im guessing there must be something with the Windows 7 OS.

Maybe you are looking for

  • A workaround for Aperture users to use .Mac Web Gallery

    As a user who recently switched to Aperture - I was hugely disappointed seeing some amazing new photo-related features in iLife '08 not available for Aperture users. Let alone the cash for purchasing software suites, I can't convince myself switching

  • TS4006 how to open the app on my mac?

    How do i get the Find my phone App to open on my mac after ts been downloaded ? So i can find my phone .

  • Reading Application ID in WD ABAP application

    Hi All,         I have three Application ID's ID1, ID2 and ID3 and i set this in my URL which i make use of to call this application which in turn sets application parameter value, may i know how i can read this ID in my view ? Regards, Anoop

  • Will there be an Ergotron MX Desk Mount arm for the IPAD 2?

    Having trouble finding a functional AND attractive clamping desk mount for a drafting table (which sits at an incline). The Ergotron is pefect but only made for computer monitors. After having researched this for a couple of weeks, Im here to tell yo

  • Installing Snow Leopard on New Lion formatted macbook pro

    I just purchased a new 15" macbook pro and it came with lion. I need to revert back to snow leopard for a couple of my programs because they aren't currently supported. When I try to boot from the snow leopard disc to add a partition to my hard drive