Small office VoIP system

Good morning everyone,
I am currently defining the architecture for a very simple VoIP network that is to be installed in a small office (about 70 VoIP extensions). Initially, we don't want to include any special feature, just the internal voice IP service and the ability to make up to 4 simultaneous external phone calls through PSTN.
We are going to acquire a Cisco 2921 Router, the SL-29-UC-K9 Unified Communications licence and a VIC2-4FXO. 
I have been reading about ISR G2 licensing, but I am still not sure of fully understanding what we need for this project. My question is, does the UC licence for the Cisco 2921 include the FL-CME licence to use the Call Manager Express functionality? do we need something else? any special license for the FXOs functionality?
Thank you for your help
Pablo

Thank you guys for your answers,
Actually, it's my first contact as a developer with VoIP and UC Cisco technology... so I would like to keep it simple at the beginning: just internal voip phone calls and the possibility to ring pstn extensions. Our budget is very limited too... so I need to stick to the hardware that I told you in the previous message: 2921 + fxo card. 
As far as I have read, SRST functionality is very useful when you have several nodes, to provide survival to each local node that loses connectivity with a centralized call manager. But in our scenario, with a single node... I think we can give up this functionality.
So, we only have budget to purchase any other license that could be necessary to accomplish this small project. so the key question is: does SL-29-UC-K9 Unified Communications License include Call Manager Express functionality and the ability to use de FXO card to make pstn phone calls as well? because that will be more than enough for us...
thank you very much
Pablo

Similar Messages

  • Help with small office PBX system.

    Hello all,
    I'm looking for any help or advice here.
    We have an old Panasonic PABX, 3 external CO lines and 16 extension lines (only 8 in use).
    Question 1.
    We have CO1 connected to the fax/broadband number. C02 and CO3 connected to our other number. How is it possible that CO2 and C03 use the same line number but are in fact 2 separate usable lines? I am going to check with BT but is it possible this is a 'feature line' or similar?
    Question 2.
    An issue has arisen where C03 will not hang up a call. People keep saying they are not able to disconnect the call from the other end either.
    Any clarification or clues on this would be greatly appreciated.
    Olly.

    Hi
    It is possible to have a business number with more than one line (aux working). Most large business's have this set up, the designation would normally have line 1 line 2 line 3 etc etc.
    You would need to talk to who ever supplied the system to you, to get them to check the settings for line 2 (of your main number, which is line 3 on the system. You could contact BT Business Fault reception on 154 to get them to test the line
    (If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
    If I have solved your Issue please click the "Mark as accepted solution" button.

  • VoIP for Small Office

    Hi all-
    I am new to VoIP technology and currently working on a study for the business on deploying VoIP. Our business is small and currently is connected to the interent via DSL. We do have some Cisco routers and would like to know what is involved in deploying VoIP for our small office!
    Thanks in advnace,
    sK

    You need a router in the branch. As small as an 857 or 877 can do. The difference is that the 857 doesn't support QoS, VLAN and other features, beside that will work fine. The following url will help you:
    http://www.cisco.com/web/psa/products/tsd_products_support_maintain_and_operate.html
    look not much further than here, I've used this to implement Auto-Qos:
    http://www.cisco.com/en/US/products/hw/switches/ps4324/products_configuration_example09186a0080722cdb.shtml

  • VOIP system for small company

    Hi, I am planning to replace phone exchange, and thinking on something with VOIP system, my main requirements are:
    - 2 isdn lines for backup
    - 4 voip lines
    - up to 15 users
    woud uc500 be a good solution or would you recommend anything else?
    Thanks

    The UC540 would be perfect IMO. Find a good SIP provider and your only limited by bandwidth and the number of DID's and I guess DSP resources but at 15 users I wouldnt worry to much about that. CCA is much improved now compared to what it was a few years ago and you should be able to get it up and running pretty quickly. There are tons of resources under the technical enablement labs for the UC5xx/SBCS product line. We did a roadshow the last quarter of 2010 and used most of those labs (the ones in under the technical enablement labs page) to show partners all the ins and outs of the UC500 product line and I know during the ones I did I had a ton of Account Managers who felt confident enough to actually do the technical install of a basic system after a few days of training. Cisco is dedicated to making sure their partners and their customers have every tool possible to be successful so use them!
    Zac

  • 1 small office + 2 companies + shared resources = ? (SG300, SA520, WAP2000)

    I need to configure a network in 1 small office space that segregates 2 company domains but allows them to share an Internet connection, a WAP, a couple of printers, and a non-Cisco VoIP phone system. And, it needs to provide guest access to the internet and printers via wireless. I have a SG300-28P, an SA520W, and a WAP2000 to make it all happen. Here's the plan below. Will this work? Is there a better approach that uses the available equipment? Thanks in advance!!!
    VLANs:
    VLAN 1 - default, mgmt vlan, 192.168.1.0
    VLAN 10 - CompanyA-Data, 192.168.10.0
    VLAN 20 - CompanyB-Data, 192.168.20.0
    VLAN 30 - Guest, 192.168.30.0
    VLAN 50 - Printers, 192.168.50.0
    VLAN 100 - Internet, 192.168.100.0
    VLAN 200 - Voice, 192.168.200.0
    Device IPs:
    SG300 = 192.168.1.254
    SA520 = 192.168.1.1
    WAP2000 = 192.168.1.245
    DHCP Servers:
    VLAN 10 = SBS-A
    VLAN 20 = SBS-B
    VLANs 30,50,200 = SA520
    VLAN 1,200 = NO DHCP
    Wireless:
    SA520 is primary, WAP2000 is repeater (will it repeat multiple SSIDs???)
    SSIDA - VLAN10
    SSIDB - VLAN20
    SSID-Guest - VLAN30
    Switch Ports:
    SG300:
    1 = trunk, VLAN 1
    2-6, 25 = access, VLAN 10
    7-12, 26 = access, VLAN 20
    13 = access, VLAN 30 (unmanaged switch providing additional ports)
    14 = access, VLAN 50 (unmanaged switch providing additional ports)
    15-23 = access, VLAN 200
    24 = trunk, VLANs 10, 20, 30 (connect to WAP2000)
    27 = unallocated
    28 = trunk, all VLANs (connect to SA520 p4)
    SA520:
    1-3 = access VLAN 1
    4 = trunk all VLANs (connect to SG300 p28)
    Routing:
    SG300 in L2 mode using SA520 as router on a stick??

    Hi Rick,
    This is a great question that our Partner Design Support team can help you with.  Please go here to start chatting with them:
    https://supportforums.cisco.com/community/netpro/small-business/partnerzone/pds
    Refer the engineer to this post so that they can see what you have.
    Regards,
    Cindy Toy
    Cisco Small Business Community Manager
    for Cisco Small Business Products
    www.cisco.com/go/smallbizsupport
    twitter: CiscoSBsupport

  • Perfect router for small office (2-3 peoples)

    Hello,
    I'm trying to find the most cost effective VoIP solution for one of our small branch offices. This office will have no more than 3 peoples, but each person requires to have a PC and Cisco IP phone (voicemail, multiple line, direct inbound, pstn dial out and etc).
    Building will provide ethernet hand-off for internet access (part of T1 I guess) so we are planning to create VPN connection between our data center and the local gateway.
    As for the PSTN connection, 2 POTS will be provided by LEC. Gateway should be able to accomodate 4 Ports FXO module.
    What would be the smallest but the best router can handle firewall/VPN/IP Voice/PSTN for the small office?
    Thank you very much for your help in advance.

    Hi,
    What drives the price up a bit is the FXO requirement. Cisco used to have a router small as the 1751V, but it is EOL now, so the smaller you can get is a 2801. The price is almost the same but the earlier model was a bit more office-friendly due the box shape and size, while the 2801 is a classic rack box 1 unit.
    The good thing with the 2801 is that it supports POE (optionally), so if you put one 4 or 9 port ethernet switch (HWIC) in the router, your phones can work without the external power supply.
    You can configure the voice system be totally controlled by the router itself with the embedded CCME, or be part of company's CallManager (now CommunicationManager)
    Can I give you another advice, try to get ISDN BRI preferentially instead of FXO. You will have all the features like DID, caller-ID, and much easier setup a diagnostic in the router. Plus, if you add a WIC-1B/ST you can also have ISDN backup using the same data facilities.
    Please remember to rate useful posts!

  • Do VOIP systems work with regular phone lines?

    Hey there, I'm an old phone tech and I'm looking to expand from regular telephone systems into the VOIP market.
    What I need to know is whether a VOIP system can be hooked to regular dial-tone?
    I basically want to hook the telephone numbers into the system, let the phones in my customers office have access to these lines, and use the VOIP side of things to connect a remote office on the other side of the state.
    I need to be able to connect anywhere between 1-20 phone numbers and 1-60 telephone sets.
    Can anyone help me out or point me towards a model that will do this?

    Always good to see an old PBX tech embracing the new and wanting to understand this sort of technology.
    PBX's and analogue voice ports work fine together, we have made many grumpy customers happy after we understood their requirements and reverse engineered how the PBX actually functions :-)
    What you are talking about is refered to as toll bypass - you set up a first choice route on the PBX to point to the tie line and outpulse digits to the router which then makes the call.
    Best way to connect PBX's and VOIP systems is using E&M ports as they give end to end answer and disconnect supervision, but these are not all that common on smaller PBX's and key system.
    You can trunk via FXS and FXO ports, but these may cause issues with disconnect supervision, especially if the PBX does not support battery reversal or disconnect tones.
    The short answer is basically that everything you want to do is possible and we have successfully done it many times. There are a lot of other things to consider though, such as -
    Call Signaling - SIP or H323
    Dial Plans - scaling the network as it expands
    Bandwidth per call - codecs used between sites
    DTMF relay - passing digits over the IP cloud
    Interface types (E&M type 1,2,3,4,5) , FXO, FXS, Loop start , Ground start
    Disconnect supervision - battery reversal, tone based, power denial
    Hookflash control of features
    There is a lot of good material in the Cisco Press book on VOIP. Check out Amazon or one of the on line booksellers.
    If you give us some more details about what you are proposing we could give some more pointers.
    You may want to consider becoming experienced with CallManager Express as this is an ideal way to get started with VOIP, IP telephony and IP based voice mail systems. This book covers it very well -
    http://www.amazon.com/Cisco-Communications-Express-CallManager-Networking/dp/158705180X

  • Problem using File sharing  in a small office network

    I have a problem using File sharing on an Imac and Macbook Pro.
    My office has a small network running Windows Small office file server 2003. I have one Windows 2000 PC connected to it and 3 Macs, an 2.4 gHz Intel iMac running Leopard 10.5.6 , a MBP running the same and a Mac Mini running 10.5.
    From the Finder Shared window of the Mac Mini, I can see all the computers on the network. It also used to be the case for the iMac, but the MBP could never see the Windows PC’s, not the server or the Win2000. This wasn’t a big problem as I was communicating between the Macs and using the shared printer on the iMac.
    On Monday Jan 19 the iMac was suddenly unavailable to the other 2 Macs. It was working normally on the Friday. The iMac can access the Mac Mini and copy files to it. The Mac Mini can see the iMac but cannot access it. Even trying to connect as, ends in a failed connection. I have tried rebooting, turning File sharing off and then on again to no avail.
    The iMac now also cannot see the Windows PC’s which it previously could.
    To get files from the MBP for printing, I now copy it to the Mac Mini and acces the folder from the iMac, a very tedious procedure. I don’t know why this happened and am scared that the Mac Mini is going to do the same thing.
    All three computers are also running VMware 2.0 with Windows XP pro, and from VMware the server is visible on all the computers.
    Any help will be much appreciated, I live in a small town in South Africa and the local computer suppliers have no knowledge of the Macs.
    I think that the problem with the iMac may have started after a software upgrade to 10.5.6 but I am not entirely sure.
    Thank you
    ajdk

    Well, you're current method sounds pretty good. But if you want to user a file server, hey go ahead.
    What you want to do when you centralize project files is to keep track of which one is the newest and becareful not to overwrite files with the same name. So you either have to set up individual spaces on the server (separate AFP/FTP folders maybe), or you'll need to run a file checkout service.
    The individual space is cheaper, but it's not much of a difference from backing up to the network drive. Since you have Gigabit connections, you might even opt to save ALL the user files on the server instead of just the project files.
    If you want to run a file checkout service, there's two approaches. You can run a service that can host any kind of file, or you can run a version control system for each kind of application (Photoshop, Word, etc.). Please notice, that as you read further and further along, the methods become more and more expensive and complicated. Once you get to this point, it will be necessary to purchase or build software in addition to the Mac OS X Server package.

  • How to setup a small office network

    Hello,
    I am looking to setup a small office network comprising 6 G4 macs (existing computers) that have been upgraded to the newest OS version. What is the best way to go about networking these computers together in terms of being able to share files, internet connection, access to peripherals and also implementing a firewall.
    Any suggestions or help would be greatly appreciated.
    Thank you

    1, Get a cable internet ISP account; depending on your service you should be able to secure a 5Mbps down and 2Mbps up on the cable e.g. Cox or Comcast.
    2. Get a good router. The mass market Linksys and Netgear routers aren't very good in terms of reliability. I use a ZyXEL P-330W router is the best I've ever seen. Its reliable and very efficient in terms of throughout. The Apple Airport Extreme is good.
    3. Set up the router to support UPnP. This way all computers will be able to share iChatAV video conferencing. If you enabled "port forwarding" only one Mac would be able to use iChatAV video conferencing.
    4. Set up your router for DHCP to dynamically issue Internet address to all your computers.
    5. Setup the wireless router for encryption such as WPA. This will encrypt wireless communication.
    6. Setup the wireless router for only your computers. You'll have to get the MAC/AirPort ID network addresses as expressed in terms of an xx:xx:xx:xx address. You can get this thru your Systems Preferences -> Network window -> AirPort (in the sidebar) -> Advanced button.
    7. If you have Ethernet in your office then skip steps 5 and 6 above.
    8. On each computer open up the System Preferences -> Sharing and check-off the File Sharing. Set your user access preferences appropriately.
    9. Get a Network enabled All-in-one printer and setup Printer Sharing options. Hook-it up to your network and add your printer by clicking on the "+" sign in your "Print and Fax" Preferences.
    10. Don't enable Apple Firewall on each Mac. The router will be the Firewall.
    Ok. That's the short-hand.. plug it all in and go!

  • Setting up a small office network - advice needed

    We are to move our small office (3 people) from a shared office environment to our own office space. That has the huge advantage that we´ll finally be Mac-only, but the agreeable disadvantage that there is no longer a networking professional around. And this is where I enter. I now have to find a solution on how to set up the network, and I do not have experience in that field (though I am fairly experienced with OSX).
    As of today we have a G5 iMac, a G4 powermac and a G4 iBook. In the not too far future we will be getting a proper G5 powermac as well.
    The G4 is used for low key office applications, Word and Mail mostly. The iMac is the workhorse that runs all graphic/video applications. It also is used for presentations once in a while, so that this machine is not always available. The iBook is used for writing and e-mail plus some light-weight field editing.
    I would like to find a solution that we could store all important files on one computer, so that it would be easier to make regular back-ups. And everyone could easily access those files.
    It would be great if data from iCal and Adress Book could also be stored centrally, such as that addresses are available for everyone, and updated calenders are available for all employees.
    As the budget should be as small as possible, I was wondering if we could use the G4 powerbook (867mhz, 1gig memory) to run a sharing service in the background. Then I could also install a second harddisk and use both hdd as a backing-up-raid. Once in a while I would make a backup on a external firewire disk.
    Is this a possible solution, or should we rather have one machine dedicated as a server. Would it be sufficient then to use the G4 as that server and buy a MacMini or iMac as the office machine?
    Since it is a small network, would I still need an OSX server license, or is the standard OSX enough for this?
    iMac G5 20, G4 QS 867mhz, iBook G4, PB 190, and a Pentium that I haven't switched on in months...   Mac OS X (10.4.3)   Experienced with technology, just not with networking...

    There are two ways to set up a network:
    1 peer-to-peer
    2 client-server
    Peer-to-peer is cheaper, but not reliable. Apple supports peer-to-peer in OS X. (In fact, in all versions of the Mac OS since System 7.) You can have up to 10 users connected to any one machine using peer-to-peer. (Warning... if you have more than five users, that machine is going to get slow.) The various peers are used as normal workstations while sharing. You have three peers, and may get one or two more, so you can use peer-to-peer. Just don't overdo it. Your planed usage of a few Word docs and a few graphics files sounds about right.
    Under OS X the peers are limited to sharing specific folders only, unless they use 3rd-party software such as SharePoint, which allows the sharing of any and all folders.
    It seems that you plan to use the G4 as a 'server' using peer-to-peer. You also seem to be planing to add additional drives, and RAID. I'd get a high end IDE PCI card, or a FireWire card, or a SCSI card, for the G4. Depending on which G4 you have, you can stick up to four hard drives in the case if you go IDE or internal FireWire or SCSI. External SCSI or FireWire drive configuratins are limited only by the drive slots available (7 for low-end SCSI, 15 for high-end SCSI, 63 for FireWIre) and the space available. (And, of course, the budget availanle...) You can get dedicated RAID controllers.
    For backup I'd get DVD or tape. Tape holds more and is easier to use, but is expensive (you have no idea how expensive, but I suspect you'll find out) and can be finicky. DVD is a lot cheaper, but it's slow, and someone will have to sit and feed discs into the machine. This will get old really fast. If your backup requirements are modest, DVDs might do, but probably you'll need something else. You could just buy an external hard disk and back up to that...
    Apple charges US$500 for OS X Server 10 seat version. (They charge $1000 for the 255-seat version.) OS X Server should run on the G4, and will turn it into a full-fledged server.
    Any of the O'Reilly books on OS X Server and/or on Samba should help you get started. O'Reilly's _Using Samba_ has a section devoted specifically to SMB on OS X Server which should be quite helpful.

  • Small Office Switch Questions

    Hi Guys,
    Have a small office I need to setup with a few requirements.
    I need to replace some unmanaged switches with one or two managed devices to better facilitate bandwith and general managment. There will be 5/6 VLANS (VOIP, Users, Wifi, CCTV ect), between 24 and 48 workstations requiring gigabit speeds and around 15 VOIP phones and 5 IP Cameras.
    Due to costs, i'm quite happy to go with a 24port 1000base switch and a 48port 10/100base POE switch (as I can bounce lots of devices that don't need 1000 like printers and accesspoints down to the POE switch). I was looking originally at the 3750 series (1000 and 100 and using the stacking ports) but the cost may be a little high.
    Used switches are not a real problem (unless anyone can advise on some really good reasons why) so picking up old cat hardware and getting the latest images are a option. Ideally, I want to spend under 1500 USD on something like this, but if it could be sub $1000 that would be great. In terms of the POE device, it needs to be standard POE not Cisco Pre-Standard.
    Happy to keep in the same series even if it's older.
    I've seen the small business series, but it seems that by the time you spend the money on two switches, you're nearly upto the prices of two used cats.
    Any thoughts on those?
    Thanks.

    I was looking originally at the 3750 series (1000 and 100 and using the stacking ports) but the cost may be a little high.
    You will no longer be able to purchase FastEthernet 3750 as Cisco has announced the End-of-Sale of the 10/100BaseTx of the 3560 and 3750 since January 2011.  Cisco has also announced the End-of-Sale of the 3560G/E and 3750G/E back in March 2012.
    So this leaves you with the 3560X and the 3750X and I can assure you this variety doesn't come cheap at all. 
    This leaves you with the last remaining stack-capable model, the 2960S.  Like what Paul has said, the 2960S is a "triple speed" variety:  10/100/1000BaseTx.  You can have uplinks of 1 Gbps fibre or 10 Gbps fibre.  You can have "half" PoE or Full PoE.
    But what sets the 2960S different from the 3750X (in terms of stacking) is the amount of switches in a stack.  The 3750X can support up to nine but the 2960S can support up to four.  This factor was set deliberately to prevent potential users to choose the cheaper 2960S instead of the 3750X.

  • Setup Lion Server for use in Small Office of Windows & Mac Clients

    I've purchased a Mac Mini Server with Lion Server installed to be used in my small office of less than 10 people.
    The primary goal of this server is to used for File Sharing, bother locally, and remotely.
    In the process of setting up Lion Server I have come across a couple things that I am confused about.
    The first is Open Directory.
    It is my understanding that this is not a necessary setup for the number of users in my office, however I set it up anyway as it appeared to be something that would be useful in the future.
    I have come across information that states Lion Server will not be accessible for Windows users connected via Open Directory. Thus my inclination is to disable the service, and set up my users as local users.
    My question is, for local and remote File Sharing, is there any benefit to using Open Directory?
    The second has to do with Remote Access.
    I am familiar with the notion of a VPN, but I need some clarification as to my remote access options.
    When I go to setup my Server's hostname, I am presented with three options. 1) Host name for local network, 2) Host name for private network, and 3) Host name for Internet.
    I have a domain name for my company's website, so I set up a subdomain (server.mycompany.com), asked my ISP for a Static WAN IP, and pointed thesubdomain to said IP using my DNS. Thus this appears to be option number 3; to allow users to connect to my server from the local network, as well as the Internet.
    My question is, how does this differ from a VPN both in setup, as well as method with which users will access the server? Is there a benefit to one over the other? I would Google this to find an answer, but I can't seem to find a name for what this setup is called.
    I very much appreciate any help you can provide.
    Thanks.

    Well, I spoke too soon.  Lion Server is unstable, awkward and is far too limited to qualify as an Apple product. Even though there's quite a few enhancements, the omissions of technologies in the server 10.6 edition makes this "server" a no go for us.
    Even after installing mysql, I still cannot run a Joomla website on Lion server as it should be done. The wiki's a nice thing to have, but isn't a "professional grade" solution.  There's too much iOS as well.
    With that said, I think it's a shame that apple would put customers through so much frustration and disappointment by releasing such a lame product. In order for us to use Lion server, we would have to be able to run a second (totally separate) instance of Apache. It also appears that server settings are changing to the extent that services become inaccessible as the system is running.

  • Trouble with office VOIP

    I have an office VOIP (Taridan) that connects to my office network. I have a static IP address through which I connect to the office VPN. Our IT folks know nothing about Macs. I just switched from a NetGear router to an Airport Extreme. The internet connection works great - both wired and wireless. But I cannot get the VOIP phone to work. The phone uses a wired ethernet connection.
    The IT folks have asked me to find out if the Airport Extreme recoginzes the phone, but I am having trouble finding such an identification. Some other posts seem to indicate that wired connections aren't listed anywhere in Airport Utility but that doesn't make sense.
    They also discussed port forwarding to the IP address shown for the phone, but I am having trouble identifying the IP address in Airport Utility.
    Any help would be greatly appreciated. I know just enough about networks to be dangerous!
    Thanks.
    Trey

    Sig,
    My hard drive has approx 1.5 TB Free. And the iMac has around 9 GB Of RAM (out of 16GB) in the green
    on the activity monitor.  I know in older versions of the operating system, one could assign
    more RAM to an open application, thus allowing the app to access more memory when needed
    such as having huge amounts of text on the clipboard.

  • Remote administration of small office via Internet possible?

    Hi forum,
    I am a sort of "administrator" (actually that one, who is always asked when there is a computer problem) within our small office group. But I am also very often on the road so I cannot help my workmates personally.
    Our office Macs are connected to the inside and outside world via a Time Capsule. I consider buying an ARD license, but I am unsure if this would enable me to hop on my workmates' Mac screen when I am on the road and want to connect via internet.
    Could you tell me if there is a way to accomplish this without buying new hardware or a subscription service?
    Cheers,
    Sven

    If all you need is to be able to control another computer at your office from a remote location, then ARD would be overkill. Look into the freeware VNC. That will give you control capabilities and not cost you anything. You can find VNC applications for Mac here. Mac OS X 10.4 and 10.5 already have a VNC component to allow you connect to the system so all you'd need is the portion on the computer from which you'd be taking the control. Most people seem to find Chicken of the VNC still works well for them, though it's not been updated in a while. JollyFastVNC, though still in development, is another option that's looking quite promising. You will need to open and forward the appropriate ports (TCP 5900) to the internal IP address of the system in your office. If you need to connect to more than one system, you'll need to run a third-party VNC application, such as VINE, on the office systems to you can designate the port; ARD only uses 5900 which only allows one computer to be controlled through an NAT device.
    Another option, if your users are all using Mac OS X 10.5, might be to use iChat. It allows screen sharing and isn't subject to the difficulties with IP addresses, network ports, etc. that arise when using ARD or any similar direct system control.
    Hope this helps.

  • Sharing Reports in Small Office

    Post Author: pma
    CA Forum: General
    Hello,
    I am hoping this is a basic question for someone.  We use Crystal Reports Professional II to report off a MS SQL server.  We would like to share report output amoung our small office of about 12 people.  I am told that the professional version comes with some type of web deployment system you can put on a server, but I don't see this anywhere.  I see the "Crystal Report Server" on Business Object's website, but this seems like overkill for us (not to mention too pricey).  Anyone have some simple direction on how to deploy reports?  Optimally I could schedule reports and have them viewed in a browser.
    Thanks in advance.

    Post Author: qcheng
    CA Forum: General
    Sounds like you have a Crystal Report Designer only. You may need to install BusinessObjectss or Crystal Report server on which you can publish your reports. Once you have published a report on the server, other people can get access the website and schedule the report.

Maybe you are looking for

  • Does the unlimited email/web plan give us access to the 3G network?

    since i got the unlimited email/web plan will i be able to access the internet wherever i go over the 3G network? and I also, like many could not transfer my upgrades within the family plan, very disapointed, dont look forward to the hassle of callin

  • Populate Combo in matrix

    Hi,      I have a Matrix.      In Each row i want like to populate matrix with values based on the row.      My problem is once a combo gets populated in one row, the same value      gets populated for other rows also(inspite of changing values)     

  • Finder not picking up external HD

    I have an external HD that have connected to the mac before in fact I believe it is in OX forma, but regardless when I connect the drive I can see if it disk utility but I can select it. It doesn't show up in finder but I do get a message saying that

  • Entitlementsadministration shows blank page

    Hi all, I installed OES 10.1.4.3.0 using Oracle 11g and tomcat. I am able to start the SCM and admin server. I am able to login to https://<host>:7010/asi as admin/password and see the content. But when I try to login to https://<host>:7010/entitleme

  • SM50-DUMP display error

    There are lots of error in my prd system. The line of DUMP all display red. Can somebody help me ?