SNMP OID for Port & CPU Utilization

I have a LinkSys SRW208P switch. Is it possible to retrieve Port & CPU Utilization using SNMP?
If so, does anyone know the OIDs?

SNMP sure does that. Default OID should work fine. Community password is set to "public" by default.

Similar Messages

SG-500 - SNMP OID for CPU Load?

Hello,
i have several SG500 (Standalone and stacked). How can i get the CPU Load via SNMP? Who knows the correct SNMP OID for CPU Load?
In the MIB which are provided as download a wasn't able to find the correct OID.

Hello,
There are three OIDs available for CPU usage:
CPU utilization for 5 seconds
.1.3.6.1.4.1.9.6.1.101.1.7.0
CPU utilization for 1 minutes
.1.3.6.1.4.1.9.6.1.101.1.8.0
CPU utilization for 5 minutes
.1.3.6.1.4.1.9.6.1.101.1.9.0
This came from a scrap note I had in an e-mail, so I am not exactly sure where this information is originally.
Let me know if that works for you,
Christopher Ebert - Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts*

Snmp oids for the command "show counters interface intx/y delta"

Hello,
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..
Is possible to get these values using SNMP??
Thank you
Roman

Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman

SNMP OIDs for solaris 8

Hello
Someone could tell me where to find a list of SNMP OIDs for solaris 8
thank you for your cooperation

Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman

Cat6509 - SNMP OIDs for interface stats

Hello,
I have a Catalyst 6509-E-VSS with IOS 12.2(33)SXI3.
I'm looking for OIDs to retrieve the same counters I get with the commands
"show interface stats" and "show interface switching".
I want to graph the number of packets that are process switched.
The OIDs from IF-MIB ( ifInOctets, ...) show only the total number of octets not the
switching path.
Thanks for help
Mike

After a long time silence on this frontier the problem is comming up again.
My goal is still to find out, what interface causes process switched traffic.
There is usualy a lot of traffic handled in software but sometimes (of course on weekend midnight) it seems to increase the cpu load (IP Input process).
Regarding the Cisco document "Troubleshooting High CPU Utilization Due to the IP Input Process" I want to monitor traffic by switching path.
So again - does anybody has an idea to get these counters with snmp ?
Update: IOS is now 12.2(33)SXJ3

Reading SNMP OID for used storage on px12-400r

Hi, does anyone know how get the correct value for used disk space via snmp on the px12-400r nas?
All capacity is configured as one big cifs share. I want to monitor the usage of space with snmp.
If I do a snmpwalk (v3) I can pinout the filesystem /mnt/pools/A/A0 on OID 1.3.6.1.2.1.25.2.3.1.3.38.
If I read the oid for StorageUsed I get a strange negative value: -1084997477
This value changes while data are written to the cifs share so it seems to be monitoring. But what to do with this negative value?
Thanks for any help!
/Anders

Hello anders-px12-400
I recommend checking with rtrevino from his thread. The unit's are different, but the firmware is bascially the same across all Lifeline devices
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

SNMP OID for DHCP on Server 2012

We recently installed Server 2012 standard on one of our servers and were trying to keep a graph of DHCP lease use. Anyway the OIDs for DHCP in Server 2008 R2 started with "1.3.6.1.4.1.311.1.3.2.1.1". If I try to snmpwalk these same OIDs on the new Server
2012 (We the DHCP server configured and active), I get:
Error in packet.
Reason: (genError) A general failure occured
Failed object: SNMPv2-SMI::enterprises.311.1.3.2.1.1
I'm using SNMPwalk and I've never had a problem with this before. Any idea what would cause this? Thanks!
Thanks!

I'm having the same issue. OIDs just don't work against a 2012 DHCP server. I can snmpwalk other OIDs, just not DHCP :(
Firewall has been disabled (and there were already adequate snmp rules allowing the traffic). Since I can query other OIDs, I'm ruling out firewall.
Has this info been removed in 2012?

SNMP OID for 5108 Chassis input and output Watts?

Anybody know these?
Craig

Craig,
OID for cucsEquipmentChassisStatsTable -- 1.3.6.1.4.1.9.9.719.1.15.10
UCS MIBs are available here
ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html
HTH
Padma

SNMP OID for Stuck CICs

Hello,
We have a PGW2200 and we are facing a stuck CIC problem. Im trying to monitorate it thru zabbix but I cant find the correct OID for the information. DOes anyone knows it, or can point me some document where I can find the OID ? I googled in many ways but for some reason I couldnt find the information.
Best Regards.
Luis Fernando Laimer

When I use the command:
rtrv-tc: it returns as follows:
CIC=1,PST=IS,CALL=IN,BLK=NONE"
CIC=2,PST=IS,CALL=IDLE,BLK=NONE"
CIC=3,PST=IS,CALL=OUT,BLK=NONE"
CIC=4,PST=IS,CALL=IDLE,BLK=NONE"
CIC=5,PST=IS,CALL=IDLE,BLK=NONE"
CIC=6,PST=IS,CALL=IDLE,BLK=NONE"
CIC=7,PST=IS,CALL=IN,BLK=MATE_UNAVAIL"
CIC=8,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=9,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=10,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=11,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=12,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=13,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=14,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=15,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=16,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=17,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
CIC=18,PST=IS,CALL=IDLE,BLK=MATE_UNAVAIL"
Those identified by BLK=MATE_UNAVAIL wont work.
I guess its an issue of our service provider, but for now I need to monitore the occorence of this situation.
Best Regards

SNMP OID for CPU and Memory Utilization on a MDS 9509

Does anyone know what the OIDs are for CPU and Memory utilization on a MDS 9509?
Thanks

CISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
Once you feel as though you are on the right track, have a look at:
http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
I gather that what you need is:
1.3.6.1.4.1.9.9.305.1.1.1
and
1.3.6.1.4.1.9.9.305.1.1.2
Enjoy.
Stephen

Need SNMP OID for MSTP status in Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch

Hi,
I have configured redundant network using two Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch through MSTP & it's working fine.
I need OID of MSTP status from which I can monitor which Switch is active and which one is in standby mode.
Please help.
Thanks,
Harsha

Hi Harsha,
check these OID's:
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.4.1.9.9.500.1.2.1.1.6&translate=Translate&submitValue=SUBMIT
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=cRFStatusUnitState&translate=Translate&submitValue=SUBMIT&submitClicked=true
Thanks-
Afroz
**Ratings Encourages Contributors ***

How to set up notification email for Full CPU utilization on OEM12c?

I have found a Oracle Doc,Is that's the way email notifications are setup?How can i check that after setting the notifications?
4.1.2.3 Subscribe to Receive E-mail for Incident Rules
An incident rule is a user-defined rule that specifies the criteria by which notifications should be sent for specific events that make up the incident. An incident rule set, as the name implies, consists of one or more rules associated with the same incident.
When creating an incident rule, you specify criteria such as the targets you are interested in, the types of events to which you want the rule to apply. Specifically, for a given rule, you can specify the criteria you are interested in and the notification methods (such as e-mail) that should be used for sending these notifications. For example, you can set up a rule that when any database goes down or any database backup job fails, e-mail should be sent and the "log trouble ticket" notification method should be called. Or you can define another rule such that when the CPU or Memory Utilization of any host reach critical severities, SNMP traps should be sent to another management console. Notification flexibility is further enhanced by the fact that with a single rule, you can perform multiple actions based on specific conditions. Example: When monitoring a condition such as machine memory utilization, for an incident severity of 'warning' (memory utilization at 80%), send the administrator an e-mail, if the severity is 'critical' (memory utilization at 99%), page the administrator immediately.
You can subscribe to a rule you have already created.
From the Setup menu, select Incidents, then select Incident Rules.
On the Incident Rules - All Enterprise Rules page, click on the rule set containing incident escalation rule in question and click Edit... Rules are created in the context of a rule set.
Note: In the case where there is no existing rule set, create a rule set by clicking Create Rule Set... You then create the rule as part of creating the rule set.
In the Rules section of the Edit Rule Set page, highlight the escalation rule and click Edit....
Navigate to the Add Actions page.
Select the action that escalates the incident and click Edit...
http://docs.oracle.com/cd/E24628_01/doc.121/e24473/notification.htm#CACHDCAD

Make sure you have correct thresholds...
from target home>monitoring>"Metric and Collection Settings"
Check the incident rule for warning and critical events for host targets
Setup>Incident>Incident Rules

SNMP OIDs for ASR1k

Hi everyone,
We're trying to read CPU & MEM values from ASR1006 equipment. Obviously the old OIDs are not supported on this platform. This is what we have found by going through the snmp object navigator. (I assume .2 is the ESP, .3 is the RP, .4 & .5 are the SIPs). But the values we get from the command line are slightly different than what we get through snmp. Has anyone done this before? What OIDs do you use?
=====================================================================
CPU:
1min: cpmCPULoadAvg1min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.5; Value (Gauge):
5min: cpmCPULoadAvg5min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.5; Value (Gauge):
15min: cpmCPULoadAvg15min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.5; Value (Gauge):
======================================================================
Memory:
cpmCPUMemoryUsed
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.2; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.3; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.4; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.5; Value (Gauge): KiloByte
cpmCPUMemoryFree
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.2; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.3; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.4; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.5; Value (Gauge): KiloByte
Best Regards,
Babak

Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman

Is there a single snmp oid for flash and dram ?

Does a single univeral oid (or 1 for flash and one for dram) exist that will provide total amount of flash and total amount of dram across all chassis families ?
Thanks

This link is your best bet:
http://www.cisco.com/warp/public/477/SNMP/contiguous_memory.html

SNMP OID for AssociatedAPs in Virtual WLC 7.4.100.0

Hello Guys!
I need you help for something that I need to do to monitor my Wi-FI network.
I'm using a Virtual WLC (SW Ver 7.4.100.0) where most that 30 APs are associated with, but I would like to monitor each disaciossiation of APs using SNMP. After some search, I have found this OID .1.3.6.1.4.1.14179.2.1.1.1.38 on some forums but it doesn't work, I see random number in my monitoring tool.
Do you know if there is any another OID to use with this software version or maybe if I have to upgrade to ver7.6 or ver8?
Thanks in advance,
Kevin

I'm assuming you don't own a license for Cisco Prime Infrastructure
One thing you can do is send SNMP traps to your monitoring software from the WLC (I've never used virtual WLC but my assumption is most options are the same. If your software doesn't support SNMP Traps consider a different monitoring software...
Go to Management > SNMP > Trap Receivers and set up your receiver
Then to to Management > SNMP > Trap ControlsHere is where you set what traps are sent via SNMP. If you see the "AP" tab you can set several things.
If you only want to see if an AP is dropping off the network and the above doesn't work, you could just put dhcp reservations on your APs and have your software ping it. This of course is only if its off network, not if it simply disassociates.

SNMP OID for Port & CPU Utilization

Similar Messages

Maybe you are looking for