Snmp-server community over VRF

I'm in the process of rolling out snmp-server community for LMS for all our devices. A few devices is VRF enabled, hence I need to ping the LMS server through a VRF and not the global routing table. To my knowledge the ' snmp-server host 11.22.33.44 vrf VRF XXXX' command only sends traps/notifications to DFM , is there a similar comand for the 'snmp-server community xxxx RO 1' ?
I can ping the device from the LMS server but the snmp-server community access-list does not show any hits for the LMS IP and hence the device is not registered in LMS.
Any ideas?

So manually-initiated communications appear to be working in both directions. That's good.
Since you're not seeing hits on your acl at the device, I'd next check to see the traffic leaving your LMS server. You can run a Wireshark capture there (or use the built-in packet tracer), filtering on your device's destination IP. I'd initiate a comms check from Device Center in LMS (or snmpwalk from the cli) to manually trigger an SNMP query.
If you don't see any SNMP queries leaving, LMS is the culprit (I'd check the DCR entry for the device in question). If you do see the traffic leaving then there is a network / device issue.

Similar Messages

SNMP server on PIX IOS 7.2 over VPN

Hi Team,
I have a simple query for the issues I m facing currently.
I have @ remote site remote site PIX firewall which is configurd to get the Snmp poll on the server locate outside via site to site VPN.
There is another snmp server located also in inside which I’m not managing it .
========================================================================
below are the command for the snmp configured on PIX.
snmp-server host inside x.x.x.x community XXXXX ---This is not managed by us
snmp-server host inside x.x.x.x community XXXXX
snmp-server host outside y.y.y.y (private IP tunneled though VPN) poll community YYYYY ---Managed by us
snmp-server host outside y.y.y.y poll community YYYYY
snmp-server community XXXXX
snmp-server enable traps snmp authentication linkup linkdown coldstart
snmp-server enable traps syslog
access-list acl-VPN-tunnel line 2 extended permit ip host z.z.z.z (outside interface of PIX firewall) host Y.Y.Y.Y (server located outside)
==============================================================================
there are 2 snmp community & server defined in snmp-server host command for 2 different IP address belongs to snmp server and we can only define one global snmp-server community for any one of them .Question is how the snmp community take a precedence .
Currently I am able to ping from my snmp server from outside to the PIX firewall outside interface over L2L VPN but somehow the snmp server is not listening when i do port query on 161 por!.
Appreciate you inputs for the same and let me know if any more details are needed

What was the resolution? I am having the same issue.
Thanks!

Process Failure when communicating over MODBUS using LabVIEW 2011 and DSC

I'm currently trying to read from a PLC's holding registers using MODBUS/TCP. I've confirmed that the PLC is updating the values and responding to MODBUS communication correctly using a third party program called Modbus Poll. However, when I try to poll the PLC using LabVIEW's shared variable engine, I am unable to read any values from the same addresses that I'm viewing with Modbus Poll.
My setup simply consists of a PC connected directly to the PLC over Ethernet, with no router in between. I am using LabVIEW 2011 SP1 with the DSC module.
I opened the NI Distributed Systems Manager to view the status of all shared variables in the Modbus library that I created and I've noticed that the CommFail bit is permanently set to "true". All other variables with a "read" access mode report "Process Failure". I've tried restarting the process as well as stopping and starting the local variable engine with no success. I've also restarted my computer several times to see if any services were failing, but this does not seem to have fixed the problem.
I finally resorted to monitoring communications over the network card that I have the PLC plugged into via Ethernet using Wireshark and I've found that while Modbus Poll is communicating with the PLC, many MODBUS and TCP packets are sent and received. However, when solely using LabVIEW or the NI DSM to communicate with the PLC, there does not appear to be any communication over the network card.
Something that may be worth noting is that I was able to communicate with the PLC and read values from it with the DSM on just one occasion, when I first figured out which addresses I should be reading from. It all stopped working shortly thereafter. Prior to this, "CommFail" was not usually set to "true" with my current configuration. Thinking that it was my firewall, I have since turned my firewall off, but this seems to have had no effect on the problem either.
Any help on this matter would be appreciated.
Solved!
Go to Solution.

Just a thought but I think the register addresses used by LabVIEW are one off of the actual register #. I was using a CRIO as a modbus IO Server and had to shift the register addresses by 1 to get things to work correctly (can;t recall if it was +1 or -1). This is documented somewhere on ni.com but can;t seem to find it now. But here is another link that may help:
http://zone.ni.com/reference/en-XX/help/371618E-01/lvmve/dsc_modbus_using/
Dan

Receiver SOAP channel error: Communication over HTTPS. Unable to create a socket

Hi,
I am getting following error while sending message from PI (7.1) to SalesForce system:
'SOAP: call failed: java.io.IOException: Communication over HTTPS. Unable to create a socket'
Scenario: Sending Customer data from SAP via Async proxy to PI which is sent further to SalesForce system via SOAP webservice call.
When I am trying to Post data to the same webservice via SOAP UI it is working fine and data is getting updated in SalesForce system.
XPI inspector logs for the channel suggest the following:
client [103965] RequestImpl.initSslAttributes(): Initially sslAttributes = null
client [103965] RequestImpl.initSslAttributes(): Cannot find SSL headers in the request.
client [103965] RequestImpl.initSslAttributes(): No SSL attributes: not found in headers and not searched in FCA, because connection.isSecure() = false; sslAttributes = null
I have checked the following SAP Note and requested for updation of SSL icm parameters
891877 - Message-specific configuration of HTTP-Security
I checked the following discussions:
http://scn.sap.com/message/8910518#8910518
http://scn.sap.com/message/6244674#6244674
http://scn.sap.com/thread/2100000
http://scn.sap.com/thread/1632114
which are suggesting a different approach. Kindly suggest a way forward.
Thanks,
Vishwajeet

This is related network issue.
Did you do telnet in pi server with target system ip and port?
If you use https then you need to install certificates.
Check below threads
http://scn.sap.com/thread/190299
Unable to create socket error

Prime Infrastructure 2.0: Running an inventory sync removes "snmp-server location" in running-config

Hello,
we're running Prime Infrastructure 2.0 (version VA-2.0.0.0.294).
I was scared as I figured out one hour ago that running an inventory sync (Device Work Center) removes the command snmp-server location and adds the command snmp-server host "PI-ip address" "snmp rw community" in the running-config.
Has someone the same behaviour or can reenact this scenario?!
Can someone imagine that this behaviour has something to do with a configuration setting in PI?
I'm perplexed and got gray hair now.
Thank you for your answers or tips.
Bastian

Hello Rob,
I just successfully installed the patch. The snmp-server location is not touched anymore while running a inventory job.
But PI still enters this string in the running-configuration:
snmp-server host "PI-IP address" " our snmp RW community- string"
although there already exists the entry:
snmp-server host "PI-IP address" version 2c "community-string (not the snmp rw-community-string)"
Do you or anyone else has the same behaviour that PI adds automaically himself as snmp trap receiver with the SNMP-RW community?
Regards
Bastian

Cisco Works SNMP write community string Incorrect

Hi,
I have installed Cisco Works at my organisation. Under RME -> Inventory -> Import status -> Device Attribute Error: I am getting: Incorrect SNMP write community strings. Even though i know perfectly well the SNMP write community string is correct. To prove that, if I delete the device and then add the same device using the same SNMP write community string it works fine. then a couple of days later, it comes up with the same message "SNMP write community string is incorrect". I have increased the time and retries for the SNMP settings at the ANI server, still it has not resolved the issue.
Please help

I have sharched the CCO bug toolkit and according them, it was a know issue for verion 3.4 but it has been fixed for Ver RME 3.5. But we are currently running RME 3.5, therefore it does not make any sense.

"Error Getting Licence. License Server Communication Problem. E_ADEPT_DOCUMENT_OPEN_ERROR

After a fatal HDD crash and rebuild, my ADE was working fine but now it's not. I purchased a book from Google, it starts to download to ADE then I get the ADE message "Error Getting License. License Server Communication Problem. E_ADEPT_DOCUMENT_OPEN_ERROR. Can anyone help? I've re-booted and re-authorized with no success. My wife is all over me to get this fixed so she can read the book. Thanks.
FYI: ADE 4.0.3 Windows 7x64

I was unable to download the book so I couldn't open it. However, I've been doing some experimenting and have finally got the book downloaded to ADE with some challenges. Here's what happened.
Prior to my HDD crash my Digial Editions library was on C:drive. When I restored my lost data it put it back on the C:drive. I copied it with all my other data to the new My Document on F:drive, pointed my existing My Documents to the F:drive.and re-installed ADE. It worked but VERY VERY slow loading. (4 minutes and not the only program to slow down. I checked drive share and everything should work well but it doesn't). Fine, I then pointed My Documents back to the C:drive and the original ADE library. Voila! It loads right away like it used to but now I get the open document error. This morning I redirected My Documents back to the F:drive which is where it was when I set up ADE. It again took many minutes to load but then allowed me to download the book.
So I guess the real questions is this: How can I move my ADE 4.0.3 library from the F:drive back to the C:drive without getting this kind of error? In absence of any better suggestion I'm going to uninstall ADE, point My Documents back to the C:drive which contains the original restored ADE library and re-install ADE. Do you think that makes sense?
Thanks for your help.

IMAPS Support from Portal Server Communications Channels?

I have successfully installed the Sun ONE Portal Server Communications Channel v6.0 onto a Portal 6.1 Server, as per the instructions. I'm trying connect to an installation of Messaging Server v5.2 which is set to only allow secure connections (IMAPS). Can someone tell me what configuration changes I need to make to the channels to connect over IMAPS?
Thanks for your help!

Fortunately Communications channels don't use
portal user desktop profile - they use LDAP attributes
to store configuration for each user.
There are several good examples how to create/modify
ldap attributes from a script. See Directory server docs.
Cheers,
Alex :-)

Instant Message client - server communication

Hi,
I am writing an instant message application that has central server and many connected clients. When one client writes a message to the server, the server echoes the message to all concerned clients
My server is a servlet, running on a J2EE web server. My client should run on Windows operating system and communicate with the WIN32 API.
My problem is:
The server is written in JAVA and my client should use the WIN32 API (in order to add its icon to the Windows tray for instance). How should I perform the client - server communication? What protocol/technology should I use? Should I write my client in C++ and from the server open a socket and perform HTTP requests? It looks too low level to me and not the �right� approach. Does it make sense to write my client in java and let it use JNI? And if yes, what is the preferred way of client � server communication?
Is there any good reference I can use?
Thanks

The both alternates you are thinking over are fine. But the later one may cause some performance and memory issues.
If you want to go with the first alternate, I suggest you to develope your owen server using ServerSocket and use your own protocol for communication between client and server over the sockets. Because using HTTP protocol will slow down your entire application. It adds overhead because each request passes through the servlet container.

Why am I getting the error: error getting license License Server communication problem W_ADEPT_CORE_EXPIRED when I try to download a book from the public library using Adobe Digital Editions. It has been working for a few months, but now I suddenly get th

I have checked and the Adobe Digital Editions is authorized. The library book doesn't expire for another 14 days. These have been the only two suggestions that I have found in other forums. Does anyone have any other suggestions?

I am having this exact issue. I just downloaded a book and went to open it and got this exact problem.
I purchased he book through indigo/kobo edition and paid for it and immediately went to open it and am getting the same error
Error getting License. License Server Communication Problem only mine says Bad Device key after.
Not sure why someone has not answered this question yet...i am using windows 7 and this is how i always do it. Never had this problem before when purchasing a book.
i hope someone answers this soon.

When I open a book in Adobe Digital Editions, I get the following error: Error getting License. License Server Communication Problem: E_ADEPT_DOCUMENT_TYPE_UNKNOWN:

Hi, I bought an e-book in PDF format that uses Adobe DRM. I've created an account on adobe.com and tried downloading the book in Adobe Digital Editions on the Mac (as well as the bookstore's e-reader--logged into my Adobe account--on an Android device).
It tries to download the book but get's the following error:
Error getting License. License Server Communication Problem:
E_ADEPT_DOCUMENT_TYPE_UNKNOWN:
Has anyone come across this? Any guidance would be most appreciated!
Thanks!
Tony

Please refer to the KB article, Public Knowledge Base

Window Server communications from outside of session allowed for root

Hi ,
When I am running the following program, i got the exception as
49:wasp.corp.apple.com_kevinli:/ngs/app/giat/src/java/chart> java MyFrame
kCGErrorRangeCheck : Window Server communications from outside of session allowed for root and console user only
Exception in thread "main" java.lang.InternalError: Can't connect to window server - not enough permissions.
at java.lang.ClassLoader$NativeLibrary.load(Native Method)
at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1586)
at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1503)
at java.lang.Runtime.loadLibrary0(Runtime.java:788)
at java.lang.System.loadLibrary(System.java:834)
at sun.security.action.LoadLibraryAction.run(LoadLibraryAction.java:50)
at java.security.AccessController.doPrivileged(Native Method)
at sun.awt.NativeLibLoader.loadLibraries(NativeLibLoader.java:38)
at sun.awt.DebugHelper.<clinit>(DebugHelper.java:29)
at java.awt.Component.<clinit>(Component.java:506)
at MyFrame.<clinit>(MyFrame.java:6)
import java.awt.*;
import javax.swing.*;
public class MyFrame
public static JFrame f = new JFrame();
public static void main(String[] args)
JFrame.setDefaultLookAndFeelDecorated(true);
f.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
//Add the ubiquitous "Hello World" label.
JLabel label = new JLabel("Hello World");
f.getContentPane().add(label);
//Display the window.
f.pack();
f.setVisible(true);
Please send a reply on this.
with regards,
Mohan

Seth,
you may also install the latest update (10.4.6) using the combo file from apple.com.
Mihalis.
Dual G5 @ 2GHz Mac OS X (10.4.6)

I keep getting the following message after I download a book and try to open the book from my downloads (in finder) Error getting License. License Server Communication Problem: E_ACT_NOT_READY. It gives me no other information and no options other than to

I don't really know what to do. I download a book from my library and it then goes to my download folder in finder (I have a macbook pro). When I double click on the downloaded book to open, digital editions comes up and then I get the following message
Error getting License. License Server Communication Problem:
E_ACT_NOT_READY
The only option I have at that point is to close the window. My computer is registered/authorized and I have tried everything I can think of but can't get the books to download into adobe digital editions.
Help please

I am having this exact issue. I just downloaded a book and went to open it and got this exact problem.
I purchased he book through indigo/kobo edition and paid for it and immediately went to open it and am getting the same error
Error getting License. License Server Communication Problem only mine says Bad Device key after.
Not sure why someone has not answered this question yet...i am using windows 7 and this is how i always do it. Never had this problem before when purchasing a book.
i hope someone answers this soon.

I upgraded to a new apple mac book pro and now when I try to download to adobe digital edition I receive this error:Error getting License. License Server Communication Problem: E_ACT_NOT_READY

I upgraded to a new apple mac book pro and now when I try to download to adobe digital edition I receive this error:Error getting License. License Server Communication Problem: E_ACT_NOT_READY

What does that have to do with Digital Publishing Suite?
We’d love to help but if does have something to do with it, please give us
some details.

Agentry Server Communications error (14)

Hi All,
We are trying to use WPF client for testing the application,
but we were getting the below error message
To resolve that we used the local certificate generated by using steps mentioned in the below link
http://infocenter.sybase.com/help/topic/com.sybase.infocenter.dc01930.0233/doc/html/fre1383608304168.html
After installing new certificate we are getting below communication error in ATE and as well as in WPF client:
before installing local certificate Application was working fine in ATE
Message:
Requesting Public Key from Server
Communications error (14)
Connection failed
Ending transmission
Please guide me to resolve the issue
Regards,
Lekhak Patil

Hi Steve,
We got the same issue working with WPF client , Hence we upgraded the SMP server 2.3 from SP00 to SP03 .
At present the Server is SMP 2.3 SP03 but we have not installed any certificate.
Again when trying to connect to server we got the Communication error(14) error.
Do we need to install the certificate again ?
Please let us know the exact process of installing and working with WPF client with SMP 2.3 SP03
Thanks
Neha

Snmp-server community over VRF

Similar Messages

Maybe you are looking for